UV-curable low surface energy fluorinated polycarbonate-based polyurethane dispersion

UV-curable low surface energy fluorinated polycarbonate-based polyurethane dispersions were synthesized by incorporating a hydroxy-terminated perfluoropolyether (PFPE) into the soft segment of polyurethane. The effects of the PFPE content on the UV-curing behavior, physical, surface, thermal properties and refractive index were investigated. The UV-curing behavior was analyzed by photo-differential scanning calorimetry. The surface free energy of the UV-cured film, which is related to the water or oil repellency, was calculated from contact angle measurements using the Lewis acid-base three liquids method. The surface free energy decreased significantly with increasing fluorine concentration because PFPE in the soft segment was tailored to the surface and produced a UV-cured film with a hydrophobic fluorine enriched surface, as confirmed by X-ray photoelectron spectroscopy. With increasing the fluorine content, the refractive indices of UV-cured films decreased. However, the UV-curing rate and final conversion was decreased with increasing contents of PFPE, which resulted in the decrease of the glass transition temperature (T(g)), crosslink density, tensile strength and surface hardness.     

Preparation and characterization of emulsifier-free core–shell interpenetrating polymer network-fluorinated polyacrylate latex particles

The emulsifier-free core–shell interpenetrating polymer network (IPN) fluorinated polyacrylate latex particles with fluorine rich in shell were prepared by emulsifier-free seeded emulsion polymerization with water as the reaction medium. The fluorinated copolymer could be fixed on the particle surface due to the formation of interpenetrating polymer network. The resultant core–shell particles were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), dynamic light scattering (DLS) analysis, Fourier transform infrared (FTIR) spectrometry, X-ray photoelectron spectroscopy (XPS) analysis and thermogravimetric analysis (TGA). The core–shell particles possessed very narrow monomodal particle size distributions. XPS analysis of the latex film displayed that perfluoroalkyl groups had the tendency to enrich at surface and there was a gradient concentration of fluorine in the structure of the latex film from the film–air interface to the film–glass interface. In addition, compared with the latex film of crosslinked polyacrylate prepared under the same condition, the emulsifier-free core–shell IPN-fluorinated polyacrylate latex film showed better thermal stability, higher contact angle and lower water uptake.     

氟含量对含氟丙烯酸酯共混乳胶膜梯度结构和表面性能的影响

首先将制备出的平均粒径较小的含氟丙烯酸酯均聚物乳液与平均粒径较大的纯丙烯酸酯共聚物乳液按不同的比例( 1/9,2/8,3/7,4/6,5/5)共混,接着将各共混乳液在室温下(20℃)玻璃基材上干燥后,于110℃/210℃下热处理一段时间.运用接触角法,XPS、AFM、SEM-EDX等详细研究了共混乳胶膜中含氟组分含量对...     

正离子光固化聚硅氧烷的合成及其环氧树脂复合固化膜的性能

以含氢聚硅氧烷(PMHS)分别与甲基丙烯酸六氟丁酯(HFMA)和烯丙基缩水甘油醚(AGE),经氯铂酸催化硅氢加成反应将甲基丙烯酸六氟丁酯和烯丙基缩水甘油醚引入聚硅氧烷的侧链,合成了3种含氟量不同的含氟代烃侧基/环氧侧基聚硅氧烷(EFPS),用FTIR、1H-NMR和13C-NMR进行了结构表征,将这类聚硅氧烷与环氧树脂...     

Synthesis and characterization of core–shell polyacrylate latex containing fluorine/silicone in the shell and the self-stratification film

A series of core–shell polyacrylate latexes with different fluorine/silicone monomer concentrations were prepared successfully by seeded emulsion polymerization. Dodecafluoroheptyl methacrylate and perfluorooctyl methacrylate with different fluorinated side chains were employed as fluorinated monomers, and γ-methacryloxypropyl triisopropoxidesilane (MAPTIPS) was used as a silicone-containing monomer as well as a self-cross-linking agent. The morphology and chemical structure of the latexes were characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, and differential scanning calorimetry, and the self-stratification properties of the latex film were verified by X-ray photoelectron spectroscopy and static contact angle measurement. The results showed that the fluorine/silicone-containing polyacrylate latexes presented a uniformly spherical core–shell structure, and the latex films displayed a preferential distribution of fluorinated composition near the surface, which was more remarkable with the synergism effect between the fluorine monomer and MAPTIPS. Additionally, the hydrophobicity and oleophobicity of the latex films exhibited high relevance with the fluorine/silicone monomer concentrations as well as the fluorinated side-chain structure.     

Photochemical modification of diamond films: introduction of perfluorooctyl functional groups on their surface

Photolysis of perfluoroazooctane with diamond films led the chemical modification of the surface to introduce perfluorooctyl functional groups, confirmed by means of Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and time-of-flight secondary ion mass spectrometry measurements. Diamond films modified with fluorine moieties showed improved frictional property and reduction of surface energy, as evaluated by contact angle to water, compared with a pristine diamond film. The contact angle and friction coefficient of chemically modified diamond film are 118 degrees and 0.1, respectively. The results of the value of the contact angle depending on irradiation times are consistent with those of the F/C ratio of fluorinated diamond films by monitoring with XPS.     

氧杂环丁烷/丙烯酸酯混杂体系的光固化性能研究

以氧杂环丁烷和丙烯酸酯为主要原料,加入一定量光引发剂配制成一种新型的光固化混杂体系。研究了混杂体系中引发剂的协同作用,结果显示自由基引发剂对阳离子引发剂有增感作用。通过吸水性测试、红外光谱（FTIR）、热重分析（TGA）、扫描电镜（SEM）等手段研究了固化膜的性能,结果显示混杂固化膜的力学性能、耐溶剂性能和热稳定性要优于自由基固化膜,这是由于混杂体系在固化过程中形成了高分子互穿网络结构（IPN）,其中混杂固化膜的拉伸强度为10.34 MPa,断裂伸长率为10.13%,冲击强度为15 kg·cm,附着力为1级,柔韧性小于3 mm,耐丙酮来回擦拭次数为200次。     

光致变色含氟丙烯酸酯涂层的制备及性能

选取十二烷基硫酸钠(SDS),辛基苯基聚氧乙烯醚(OP-10)为复合乳化剂,过硫酸钾(KPS)为引发剂,将2-(全氟己基)乙基甲基丙烯酸酯(PFM)与丙烯酸酯类单体采用预乳化-半连续种子乳液聚合法进行乳液共聚,再将羟基螺吡喃(SPOH)与乳液进行物理共混,制得光致变色含氟丙烯酸酯乳液。 通过多种表征手段研究丙烯酸正丁酯(n-BA)和甲基丙烯酸甲酯(MMA)软硬单体的质量比,SPOH的用量对聚合反应和乳胶膜性能的影响。 结果表明,加入含氟单体后乳胶膜与水、油的接触角提高,热稳定性提高;加入SPOH的质量分数为1.25%时,乳胶膜具有较好的光致变色性能。     

Properties and characterization of novel cationic polyacrylate latex containing fluorine and silicon prepared with soap-free emulsion polymerization

The novel cationic polyacrylate latex containing fluorine silicon was successfully prepared via soap-free emulsion polymerization of butyl acrylate, methyl methacrylate, vinyltriethoxysilane and hexafluorobutylmethacrylate in water phase, which were initiated with water soluble azo initiator and emulsified with the mixed surfactants polymerizable emulsifier and OP-10. The films of the resultant latex were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and contact angle (CA) determinator, respectively. In comparison with the conventional polyacrylate latex, the thermal stability and water resistance of novel latex film are improved. The conditions of preparing the novel cationic acrylate latexes were optimized. The optimum conditions of preparing the novel latex are as follows: the amount of emulsifiers and the initiator are 6.0% and0.3%, respectively; both the amount of VETS and amount of HFMA are 6.0%. In this case, the conversion is high and the polymerization stability is good.     

Synthesis,UV-curing Behavior and Surface Properties of New Fluorine-containing Aromatic Oxetane Monomers

In this paper,we combined high-end cationic UV-curable material with fluorinated chain obtaining a series of new fluorine-containing aromatic oxetane monomers via a mild nucleophilic substitution reaction.The structures and properties of monomers were characterized using 1H-NMR,19F-NMR,dynamic viscosity tests and differential scanning calorimetry (DSC).It was determined that all of the fluorinated monomers obtained had much lower viscosity and higher thermostability after the introduction of hexafluorobenzene.Then,UV-curable coatings were prepared using four fluorine-containing aromatic oxetane monomers (FOX1-4);the UV-curing kinetics,with three kinds of initiators,and properties of the cured films were evaluated using real-time Fourier transform infrared (FTIR) spectroscopy,water and diiodomethane contact angle tests,surface energy calculations and scanning electron microscopy (SEM).The FTIR spectroscopy results showed that the coatings possessed excellent conversion rate (＞ 99％ with liquid initiator PAG-201 in 150 s),and as the fluorine content increased,the monomers exhibited decreased mobility with the increasing viscosity and worse solubility with fluorinated monomers,resulting in a lower conversion rate.Moreover,the coatings possessed favorable hydrophobic and oleophobic properties and low surface energies owing to the fluoride chains floating to the membrane-air interface,which was also confirmed by discrete concave structures in SEM images.These new kinds of monomers can replace traditional fluorinated cationic monomers applied to the fingerprint resistant,fouling resistant,scratch resistant and anti-aging coatings,adhesives or printing ink materials.     

POSS基杂化含氟丙烯酸酯共聚物涂膜的表面相分离与疏水性研究

采用自由基溶液聚合法成功合成了多面体低聚倍半硅氧烷(POSS)基杂化含氟丙烯酸酯共聚物,并采用核磁共振仪(NMR)和凝胶渗透色谱仪(GPC)表征了共聚物,其中POSS和含氟单体分步加入到反应中.首先将共聚物溶解到三氟三氯乙烷(F113)和乙酸乙酯的混合溶剂中配制成溶液,然后通过直接在玻璃片上滴落共聚物溶液制备了共聚物涂膜.采用扫描电子显微镜(SEM)、X-射线光电子能谱(XPS)、原子力显微镜(AFM)和接触角测量仪考察了F113和乙酸乙酯的配比对共聚物涂膜表面形貌、表面元素组成、表面粗糙度以及表面疏水性的影响.实验数据表明POSS在表面能够聚集成纳米颗粒并能极大增强涂膜表面粗糙度和疏水性.共聚物表面同时存在POSS聚集与有机相微相分离两类相分离行为,并形成了复合粗糙结构.虽然POSS和含氟段竞争迁移到表面,但是随着混合溶剂中F113的增多,涂膜表面含氟量越来越多,同时POSS在表面的聚集体越来越少,表面平均粗糙度越来越小,最终涂膜的疏水性越来越强,这说明F113有助于提升氟的趋表迁移能力,使涂膜表面含氟链段占据较多的表面空间,从而抑制了POSS在表面聚集分布.当使用纯F113作为溶剂时,共聚物涂膜的表面氟含量为45.25%,平均粗糙度为93.4 nm,此时静态水接触角最大为135.0?,表现出优异的疏水性.     

Preparation of an environmentally friendly antifouling degradable polyurethane coating material based on medium-length fluorinated diols

A novel medium-length fluorinated diols and poly(L-lactide) (PLLA) were synthesized via Michael addition reaction and ring-opening polymerization, respectively. Subsequently, Synthetic medium-length fluorinated diols and PLLA were combined to prepare new polyurethane composites with degradability and low surface energy. The compositional analysis and structural characterization of synthetic materials were characterized by using fourier transform infrared spectroscopy (FT-IR) and proton nuclear magnetic resonance spectra (¹HNMR). Thermogravimetric analysis(TGA) indicated that the introduction of medium-length fluorinated diols improved the thermal stability of the polyurethane. The biodegradation and low surface energy of the polyurethane were investigated by static hydrolysis experiment and water contact angle test. It was found that the degradation rate of the polyurethane increased as measurement time went on when the PLLA content was under 40%, and the water contact angle increased from 71.12° to 108.24° with the increase of fluorine content, which indicated that the degradable and low surface energy polyurethane has a potential as a coating material for a marine antifouling coating application.     

Emulsifier-free latex of fluorinated acrylate copolymer

Emulsifier-free latices of fluorinated acrylate copolymers were prepared by semicontinuous polymerization method, with perfluoroalkylethyl methacrylate (Zonyl TM) as a fluoromonomer. Ultrasonic at 40 kHz was adopted to help monomers disperse well in water. The relationships of polymerization conditions between the final conversion and polymerization stability were discussed in detail and the optimal polymerization condition was given. A fluorinated acrylate copolymer was finally obtained and its T_g was 54 °C. The average particle size of the latex was about 601 nm and the particle size distribution of the latex was narrow. The latex film exhibited a low surface free energy and good surface property. By using 6% Zonyl TM, the water contact angle of the film-air interface increased significantly and reached to 110.2°. Compared with the latex film of fluorine-free polyacrylate prepared under the similar polymerization condition, the fluorinated latex film had a better water-resistance and thermal stability.     

PREPARATION AND SURFACE PROPERTIES OF ACRYLIC COPOLYMERS CONTAINING FLUORINATED MONOMERS

A series of copolymers comprising butylmethacrylate, styrene, butylacrylate, hydroxypropyl acrylate and perfluoroalkyl methacrylate were synthesized by the free radical polymerization using BPO as an initiator. The surface property of the copolymer films was subsequently characterized. The contact angle measurements and energy dispersive analysis of X-ray （EDAX） show that the length and content of perfluoroalkyl side chains in the copolymers are crucial for the preparation of the film with low surface energy. At a given content of fluorinated monomers in the copolymers, the longer the perfluoroalkyl side chain, the larger the water contact angle of the copolymer films will be. On the other hand, the higher the content of fluorinated monomers, the lower the surface energy is. The water contact angle increases with the increase of the fluorinated monomer content and reaches a plateau at 3 wt% of fluorinated monomer content.     

Synthesis of Fluorinated Polyurethane/Polyacrylate Hybrid Emulsion Initiated by 60Co γ-Ray and Properties of the Latex Film

Based on the solvent-free method, novel fluorinated polyurethane/polyacrylate hybrid emulsions, dodecafluoroheptyl methacrylate (DFMA) as fluorinated monomer, were successfully prepared via emulsion polymerization without traditional emulsifier. For the purpose of increasing the grafting ratio of polyurethane and polyacrylate, ⁶⁰Co γ-ray radiation polymerization had been adopted to enhance the hardness of latex film. The chain structure and polymerization progress were confirmed by the analysis of Fourier transform infrared spectroscopy. The grafting ratio of polymethyl methacrylate and polyurethane was obtained by calculating the ratio of N–H peak integral area and Ph(C=C) peak integral area. The effect of DFMA content on thermal stability, mechanical property and water resistance were investigated systematically by thermal weight loss analysis, tensile strength test, absorbed water ratio and water contact angle.     

含氟丙烯酸酯聚合物乳胶膜表面性质

采用XPS和界面张力仪分别测定了含氟丙烯酸酯聚合物乳胶膜表面的组成及水在其表面的动态接触角, 并用状态逼近方程模型计算了含氟聚合物乳胶膜的表面张力, 考察了温度对乳胶膜润湿性的影响. 结果表明, 含氟聚合物乳胶膜表层较深处的F 1s信号强度比近表面要弱, 乳胶膜表面张力随表面氟原子浓度增加在一定程度上呈现线性下降；含氟侧链(Rf)较长(碳原子数n＞6)的含氟聚合物, 其表面张力随Rf单元含量增加而下降的趋势显著高于Rf较短(n≤6)的含氟聚合物, 而水在含氟聚合物乳胶膜表面上的后退接触角θr随n增大出现急剧上升, n≥10 时, θr值几乎恒定不再随n增大而改变. 此外, 参与共聚的非氟丙烯酸酯酯基碳链较短时, 水在共聚物乳胶膜表面的θr随氟单元含量增加而增加的趋势更显著；温度超过40 ℃后, 水对聚合物乳胶膜的润湿性随温度上升略有改善.     

Synthesis, characterization and properties of a novel fluorinated polyurethane

A novel fluorinated polyurethane (FPU) was prepared by fluorinated polyether glycol (PTMG-g-HFP) as a soft segment, 1,6-hexamethylene diisocyanate (HDI) or toluene diisocyanate (TDI) as a hard segment and 1,4-butanodiol (BDO) as a chain extender. Fourier transform infrared spectroscopy (FTIR), ¹H NMR, ¹³C NMR and gel permeation chromatography (GPC) were used to characterize the structure of the fluorinated polyurethane. The thermal stabilities of the fluorinated polyurethane and the corresponding hydrogenated polyurethane were studied by thermogravimetric analysis (TGA). X-ray photoelectron spectroscopy (XPS) analysis at two different sampling depths for the fluorinated polyurethane was used to investigate the surface compositions of FPU. And the mechanical properties of the fluorinated polyurethane and the corresponding hydrogenated polyurethane were also measured. Chemical resistance of polyurethane films was estimated through spot tests with different solvents. The results showed that FPU had high thermal stability, strain-hardening property and good chemical resistance. The XPS measurements showed the fluorine enrichment on the surface of FPU.     

Synthesis and Properties of Cationic Fluorinated Polyacrylate Soap-Free Latex

Cationic fluorinated polyacrylate soap-free latex (CFMBD) was synthesized by semi-continuous seeded emulsion polymerization of dodecafluoroheptyl methacrylate (DFMA), methyl methacrylate (MMA), butyl acrylate (BA), and dimethylaminoethyl methacrylate (DM) with a novel cationic polymerizable emulsifier, maleic acid double ester-octadecyl poly(ethyleneoxy)₂₀ ether-ethylene trimethyl ammonium chloride (R303), and 2,2′- azobis (2 - methylpropionamidine) dihydrochloride (VA-50) was utilized as the initiator. Effects of some factors, such as VA-50 amount, R303 amount and DFMA amount, on stability and average particle size of the CFMBD were discussed in detail, and the optimal polymerization condition was obtained. In addition, the emulsion and its film were characterized by Fourier transform infrared (FTIR) spectrometry, thermogravimetry analysis (TGA), contact angle goniometer, X-ray photoelectron spectroscopy (XPS), respectively. FTIR confirmed the structure of the CFMBD. With the increasing of DFMA amount, water absorption of the film decreased and water contact angle of the film increased. While the DFMA amount was more than 6 g in the recipe, the water contact angle (107.5°) and the water absorption (7.8 wt%) of the film showed no more changes. Meanwhile, thermal stability of the copolymer was greatly improved with the increasing of DFMA amount. XPS analysis indicated the fluoroalkyl groups had the tendency to enrich at the film-air interface.     

Development of hydrophobic polyurethane film from structurally modified castor oil and its anticorrosive performance

Hydrophobic polyurethane (PU) films are widely used for various commercial and industrial applications due to their excellent water repelling and self-cleaning property. Nevertheless, achieving appreciable hydrophobicity in PU film is quite a challenge. Herein, we report on the development of a novel hydrophobic PU (fluorinated polyurethane [FCO-PU]) film and comprehensively evaluate its anticorrosive property. The FCO-PU was prepared by structural modification of castor oil (CO) through attachment of long fluorocarbon chains as pendant groups onto the backbone of CO. A model PU film (CO-PU) was also prepared from unmodified CO to compare the properties of FCO-PU film. All intermediate compounds, FCO-PU and CO-PU films were characterized by various spectroscopic techniques. Morphological, thermal and mechanical properties of the PU films were analyzed by field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical thermal analysis (DMTA) studies. Successful introduction of long fluorocarbon chains into the FCO-PU film is reflected by its high hydrophobicity with a water contact angle of 119.1°, compared to the model CO-PU film with a water contact angle of 84.4°. Anticorrosive properties of the PU films were evaluated by polarization technique and electrochemical impedance spectroscopy under corrosive environment and the obtained results reveal a significant corrosion resistance (corrosion rate: 6.72 × 10⁻⁶ mm/year) behavior by the FCO-PU film. This work represents an effective strategy for the backbone modification of CO to develop novel functional PU materials.     

紫外光引发LDPE膜接枝含氟丙烯酸酯的研究

通过紫外光引发表面接枝聚合反应的方法 ,把含氟丙烯酸酯单体R 5 6 1 0引到LDPE薄膜上 .对经丁酮抽提后的接枝膜进行FTIR、ESCA、SEM和DSC等表征 ,证实含氟聚合物以化学键的方式接枝在LDPE基体膜上 .在一定范围内 ,增加紫外光强、引发剂和单体浓度以及反应温度等均有利于提高接枝率 .经计算R 5 6 1 0的紫外光引发接枝聚合反应总活化能为 5 4 2kJ mol.接枝膜的接触角随着接枝率的提高逐步增大 ,直至趋于恒定 .作者提出接枝膜存在一个在接触角测定时影响基体膜与探测水滴相互作用过程的边界层 .当接枝率较低、接枝层厚度小于边界层临界厚度时 ,基体LDPE影响接触角的大小 ,但随着接枝率提高 ,接枝层逐渐变厚 ,氟聚合物层对接触角的贡献逐渐占优势 ,导致接触角随之增大 .当接枝率超过一定值以后 ,接枝层厚度超过边界层临界厚度 ,接枝层对接枝膜的接触角起全部贡献 ,接触角测定值随之稳定