Dynamic mechanical properties and thermal degradation process of the compositions obtainedfrom unsaturated poly(ester urethanes) cross-linked with styrene

Dynamic mechanical and thermal properties of poly(ester urethanes) (PEU) cross-linked with styrene have been studied. The investigated polyurethanes were obtained from 4,4′-diphenylmethane diisocyanate and unsaturated oligo(alkyleneester)diol based on cis-2-butene-1,4-diol. The conducted analyses dealt with the correlation between the chemical structure of poly(ester urethanes) and their ability to phase separate as well as their thermal stability. The products of PEU thermal degradation were characterized using infrared spectroscopy.     

Block copolymer from α,ω-dihydroxyl polystyrene and polyethylene glycol

α,ω-Dihydroxyl polystyrene was synthesized by the addition of styrene oxide to polystyryl dianion initiated with sodium naphthalene. Diglyme was found to be an unsuitable solvent for the preparation of low molecular weight compounds. Block copolymerization of the α,ω-dihydroxyl polystyrenes (M?_n = 2250, 3140, and 6200) with poly(ethylene glycols) (M?_n = 404, 1960, and 5650) was pursued by introducing urethane linkages with 4,4′-diphenylmethane diisocyanate. The mechanical, thermal, and viscoelastic properties, solution viscosity, molecular weight distribution, and moisture absorption of the block copolymers obtained were examined. Incorporation of styrene blocks was found to disturb the crystallization and fusion of poly(ethylene glycol) blocks. Films cast from benzene solution were soft and elastic and absorbed up to 5.8% moisture.     

Synthesis and characterization of bismaleimides derived from polyurethanes

A series of novel bismaleimides (BMIs) were prepared from maleic anhydride and polyurethane prepolymers based on MDI (4,4′-diphenylmethane diisocyanate) and polyether and polyester diols with various chain lengths. All the BMIs were characterized by IR, ¹H-NMR, and elemental analysis. DSC studies indicated that the thermal polymerization of the BMIs could be carried out in the temperature range of 102–245°C, and that curing behavior was significantly affected by the molecular weight of the BMIs. The crosslinked BMI elastomers showed good mechanical properties and much better thermal stability than that of the traditional polyurethane elastomers. The glass transition temperatures, mechanical, and dynamic mechanical properties were dependent on the types of polyols used and the resultant crosslink densities due to various chain lengths of the BMIs. © 1994 John Wiley & Sons, Inc.     

Framed aromatic polyurethanes based on an anionic macroinitiator, 4,4'-diphenylmethane diisocyanate,and 4,4'-dihydroxy-2,2-diphenylpropane: Metal-complex modification

Metal complexes are prepared from poly(oxyethylene glycol) and iron(III) chloride and studied as modifiers of framed aromatic polyurethanes. The latter polymers are synthesized on the basis of macroinitiators, 4,4'-dihydroxy-2,2-diphenylpropane, and polyisocyanate, which is a mixture of 4,4'-diphenylmethane diisocyanate and its branched derivatives. The interaction of iron(III) chloride with poly(oxyethylene glycol) is accompanied by redox processes that lead to its degradation and partial reduction of Fe(III) to Fe(II). Aromatic polyurethanes are modified in the concentration range of metal complexes from 0.5 to 20%. At a concentration of metal complexes of 4–7%, the polymer shows high mechanical characteristics and excellent thermal stability. The framed structure of aromatic polyurethanes hampers the effective contacts of coordinately bonded Fe atoms that are present in various oxidation states.     

Studies on thermal, mechanical and morphological behaviour of caprolactam blocked methylenediphenyl diisocyanate toughened bismaleimide modified epoxy matrices

Diglycidyl ether of bisphenol A epoxy resin (DGEBA, LY 556) was toughened with 5%, 10% and 15% (by wt) of caprolactam blocked methylenediphenyl diisocyanate (CMDI) using 4,4′-diaminodiphenylmethane (DDM) as curing agent. The toughened epoxy resin was further modified with chemical modifier N,N′-bismaleimido-4,4′-diphenylmethane (BMI). Caprolactam blocked methylenediphenyl diisocyanate was synthesized by the reaction of caprolactam with methylenediphenyl diisocyanate in presence of carbon tetrachloride under nitrogen atmosphere. Thermal properties of the developed matrices were characterized by means of differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), heat distortion temperature (HDT) and dynamic mechanical analysis (DMA). Mechanical properties like tensile strength, flexural strength and impact strength were tested as per ASTM standards. The glass transition temperature (T_g) and thermal stability were decreased with increase in the percentage incorporation of CMDI. The thermomechanical properties of caprolactam blocked methylenediphenyl diisocyanate toughened epoxy resin were increased by increasing the percentage incorporation of bismaleimide. The values of impact strength for epoxy resin were increased with increase in the percentage concentration of CMDI. The homogeneous morphology of CMDI toughened epoxy resin and bismaleimide modified CMDI toughened epoxy resin system were ascertained from scanning electron microscope (SEM).     

Preparation of reflective and electrically conductive surface-silvered polyimide films from silver(I) complex and PMDA/ODA via an in situ single-stage technique

Optically reflective and/or electrically conductive surface-silvered polyimide films have been prepared by thermal curing of the (1,1,1-trifluoro-2,4-pentadionato) silver(I) (AgTFA)-containing poly(amic acid) derived from pyromellitic dianhydride (PMDA) and 4,4′-oxydianiline (4,4′-ODA) in dimethylacetamide. Films with specular reflectivity of 20-40% and surface electrical resistivity less than 7 Ω/sq were obtained. Two different thermal curing cycles were applied for the imidization and silver reduction process, and film conductivity were only obtained under rapid thermal treatment. The metallized films exhibit mechanical properties close to that of the parent polyimide films. Films were characterized by dynamic mechanical thermal analysis, X-ray diffraction, transmission electron microscopy, atomic force microscopy and mechanical measurements.     

Synthesis and properties of cationic ionomers from poly(ester‐urethane)s based on polylactide

l ‐Lactide (l ‐LA) was polymerized in the presence of N‐methyldiethanolamine as an initiator and Sn(Oct)₂ as a catalyst to give hydroxy‐telechelic poly(l ‐lactide) (PLLA‐diol) bearing a tertiary amine group at the center of the polymer chain. Successive chain extension of the PLLA‐diol with hexamethylene diisocyanate afforded PLLA‐based poly(ester‐urethane)s (PEU) with equally spaced tertiary amine groups. Treatment of the PEU with iodomethane converted tertiary amine groups to quaternary ammonium groups to give cationic ionomers (PEU‐MeI). The thermal, mechanical, hydrophilic, and biodegradation properties of the obtained polymers were investigated. The thermal properties of the PEUs and the PEU‐MeIs were similar each other. The PEU‐MeIs exhibited higher tensile modulus than those of the starting PEUs. The contact angles of water on the PEU‐MeIs were lower than those of the PEUs with similar NMDA content indicating their higher hydrophilicity. In compost degradation tests, the PEU‐MeIs showed slower degradation than those of the PEUs. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4423–4428     

Actuating Shape Memory Polymer for Thermoresponsive Soft Robotic Gripper and Programmable Materials

For soft robotics and programmable metamaterials, novel approaches are required enabling the design of highly integrated thermoresponsive actuating systems. In the concept presented here, the necessary functional component was obtained by polymer syntheses. First, poly(1,10-decylene adipate) diol (PDA) with a number average molecular weight M_n of 3290 g·mol⁻¹ was synthesized from 1,10-decanediol and adipic acid. Afterward, the PDA was brought to reaction with 4,4′-diphenylmethane diisocyanate and 1,4-butanediol. The resulting polyester urethane (PEU) was processed to the filament, and samples were additively manufactured by fused-filament fabrication. After thermomechanical treatment, the PEU reliably actuated under stress-free conditions by expanding on cooling and shrinking on heating with a maximum thermoreversible strain of 16.1%. Actuation stabilized at 12.2%, as verified in a measurement comprising 100 heating-cooling cycles. By adding an actuator element to a gripper system, a hen’s egg could be picked up, safely transported and deposited. Finally, one actuator element each was built into two types of unit cells for programmable materials, thus enabling the design of temperature-dependent behavior. The approaches are expected to open up new opportunities, e.g., in the fields of soft robotics and shape morphing.     

Preparation, characterization and dielectric properties of 4,4-diphenylmethane diisocyanate (MDI) based cross-linked polyimide films

Four different types of cross-linked polyimides based on 4,4-diphenylmethane diisocyanate (MDI) were prepared by the reaction of different types of conventional poly(amic acid) intermediates with MDI as a cross-linking agent. Subsequently, they were thermally imidized in order to obtain corresponding cross-linked polyimide structure. The results of FTIR-ATR showed that MDI can effectively react with carboxylic acid groups of PAA to form cross-linked polyimide films. TGA, FTIR-ATR and SEM analyses were carried out for characterization of cross-linked polyimide (CPI) films. Moreover, the electrical properties such as dielectric breakdown strength, dielectric constant, I-V characteristics and loss factor of MDI based cross-linked polyimides have been checked. In addition, some physical properties such as water uptake, adhesion, hardness and solubility properties of the films were investigated.The results showed that all CPI films have good insulating properties such as high dielectric breakdown voltage, low loss factor (tan δ), leakage density and excellent physical properties.     

Framed aromatic polyurethanes based on an anionic macroinitiator, 4,4'-diphenylmethane diisocyanate,and 4,4'-dihydroxy-2,2-diphenylpropane: Synthesis and characterization

Polyurethanes composed of aromatic components are synthesized using the catalytic effect of potassium alcoholates on the reaction of urethane formation occurring with participation of 4,4'-dihydroxy-2,2-diphenylpropane, 4,4'-diphenylmethane diisocyanate, and polyisocyanate, which is a mixture of 4,4'-diphenylmethane diisocyanate and its branched derivatives. In the case of 4,4'-diphenylmethane diisocyanate, segmented polyurethanes with the predetermined length of the rigid block are formed, while the use of polyisocyanate gives rise to framed aromatic polyurethanes. The use of macroinitiators as carriers of potassium alcoholate groups does not cause microphase separation of flexible and rigid segments.     

Structure–property relationships of anionic poly(urethane–urea) dispersion cross-linked with partially methylated melamine formaldehyde

An anionic poly(urethane–urea) dispersion (PUD) was cross-linked with different amount of partially methylated melamine formaldehyde (PMMF). The isothermal curing behavior was observed by a rigid-body pendulum rheometer. The test results showed that cure response of PUD cross-linked with PMMF was a function of the concentration of PMMF. Also, PMMF self-condensation could take place during the curing process. In this experiment, the anionic poly(urethane–urea) dispersion has a large number of >N–H cross-linking or branching sites in urethane and urea groups per molecule that allow a large number of PMMF to couple into elastic PUD backbone to form branched structure with partial cross-linking. The dynamic mechanical properties of PUD cross-linked with PMMF were affected by the concentration of PMMF. It was further shown that the tensile properties were strongly influenced by the concentration of PMMF and curing temperature.     

Effect of thermal curing on the properties of thin films based on benzophenonetetracarboxylic dianhydride and 4,4′-diamino-3,3′-dimethyldiphenylmethane

The processing of polyimide films from polyamidic acid solutions involves the simultaeous loss of solvent and chemical conversion, and may imply structural reorganization such as orientation or crystallization. The effect of thermal treatment on the thermal, mechanical and dielectric properties of polymer films based on benzophenonetetracarboxylic dianhydride and 4,4’-diamino-3,3’-dimethyl diphenylmethane have been investigated. The thermal treatment of polyamidic acid at different temperatures led to compounds with different degree of imidization; it turned out that the imidization process took place with high speed until 240 °C and then remained constant. The dynamic mechanical analysis (DMA), contact angles, and dielectric measurements revealed that the storage modulus and contact angles increased with increasing of curing temperature while the dielectric constant decreased.     

Products of Polyaddition of 1,1′-Isopropylidene- bis-(p-phenylene-oxy)-di-β-ethanol Thioglycolate with 4,4′-Diphenylmethane Diisocyanate and Desmodur L

Abstract

Esterification of dianol 22 by means of thioglycolic acid and some analytical tests of the product obtained were carried out. The synthesis of polyurethanes was then carried out using 4,4′-diphenylmethane diisocyanate and Desmodur L. The products of polyaddition were subject to some physicomechanical, thermal, and dielectric tests.     

Synthesis,morphology, and properties of waterborne m-TMXDI-based anionic polyurethane and hybrids

In this study, waterborne polyurethane (WPU) hybrid emulsions with a weight ratio of 2/1 were prepared by emulsion polymerization using a mixture of styrene (St) and/or butyl acrylate (BA) monomers with WPU dispersion. WPU dispersion was synthesized with isocyanic acid and m-tetramethylxylene diisocyanate (m-TMXDI)-based anionic poly(urethane-urea) dispersions using the prepolymer mixing process. The structures of WPU and hybrids were characterized by FTIR spectroscopy. The size and morphology of the latex particles were investigated using dynamic light scattering and transmission electron microscopy, respectively. The stability of the emulsions was determined according to their shelf life and particle size using the dispersion analyser LUMiSizer® with STEP?-Technology. The thermal and mechanical properties of these films were examined by thermogravimetric analysis and strain-stress curves.     

Structure-property relationships in polycaprolactone-polyurethanes

The structure-property relationships of polycaprolactone-based segmented polyurethanes were studied using differential scanning calorimetry (DSC), small-angle x-ray scattering (SAXS), wide-angle x-ray diffraction (WAXD), dynamic mechanical, and stress-strain testing. The materials studied varied in hard-segment type [4,4′-diphenylmethane diisocyanate/butanediol (MDI/BD) or 4,4′-dicyclohexyl methane diisocyanate/butanediol (H₁₂MDI/BD)], soft-segment molecular weight (830 or 2000 MW polycaprolactone), hard-segment content (23–77% by weight), and thermal history. The materials with aromatic (MDI/BD) hard segments had semicrystalline hard-segment domains, while the materials with aliphatic (H₁₂MDI/BD) hard segment had mostly amorphous domains. Materials with the shorter polycaprolactone soft segment (830 MW) exhibited thermal and mechanical behavior which indicated a considerable degree of hard- and soft-segment compatibility. The materials which contained a 2000-MW polycaprolactone soft segment exhibited better-defined microphase separation. SAXS was used to characterize the microphase structure of each system. The effects of hard-segment content and soft-segment molecular weight were similar for the aromatic (MDI) and aliphatic (H₁₂MDI) hard-segment-based block copolymers. Changing the hard segment from aromatic to aliphatic gave materials with larger interfacial area and slightly higher tensile strength. A range of morphologies between isolated hard domains in a rubbery matrix and isolated rubbery domains in a hard matrix was observed.     

Parameters affecting transition temperatures of poly(lactic acid‐co‐polydiols) copolymer‐based polyester urethanes and their shape memory behavior

A series of polyester urethanes (PEUs) comprising poly(lactic acid‐co‐polydiol) copolymers as a soft segment, 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (BDO) as a hard segment were systematically synthesized. Soft segments, which were block copolymers of L ‐lactide (LA) and polydiols such as poly(ethylene glycol) and poly(trimethylene ether glycol), were prepared via ring opening polymerization. Glass transition temperatures (T_g) of the obtained PEUs were found strongly dependent on properties of copolymer soft segments. By simply changing composition ratio, type and molecular weight of polydiols in the soft segment preparation step, T_g of PEU can be varied in the broad range of 0–57°C. The synthesized PEUs exhibited shape memory behavior at their transition temperatures. PEUs with hard segment ratio higher than 65 mole percent showed good shape recovery. These findings suggested that it is important to manipulate molecular structure of the copolymer soft segment for a desirable transition temperature and design optimal soft to hard segment ratio in PEU for good shape recovery. Copyright © 2011 John Wiley & Sons, Ltd.     

Mechanical properties and morphology of epoxy/poly(vinyl acetate)/poly(4-vinyl phenol) brominated system

Diglycidyl ether of bisfenol-A (DGEBA)/poly(vinyl acetate) (PVAc)/poly(4-vinyl phenol) brominated (PVPhBr) ternary blends cured with 4,4’-diaminodiphenylmethane (DDM) were investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). Homogeneous (DGEBA+DDM)/PVPhBr networks with a unique T _g are generated. Ternary blends (DGEBA+DDM)/PVAc/PVPhBr are initially miscible and phase separate upon curing arising two T _gs that correspond to a PVAc-rich phase and to epoxy network phase. Increasing the PVPhBr content the T _gof the PVAc phase move to higher temperatures as a consequence of the PVAc-PVPhBr interactions. Different morphologies are generated as a function of the blend composition.     

PU/MOMMT纳米复合材料的制备与研究

纳米复合材料由于其纳米尺寸效应，表面效应以及纳米粒子与基体界面间强的相互作用，具有优于相同组分常规复合材料的力学、热学等性能，引起了人们的广泛关注。用纳米材料改性聚合物，制备纳米复合材料是获得高性能高分子复合材料的重要方法。1998年以来，Pinnavaia等首先制备了聚氨酯，蒙脱土（PU／MMT）纳米复合材料，研究了有机蒙脱土在聚醚中的分散性。其后Chen等将聚羟基己内酯/蒙脱土（PCL／MMT）纳米复合材料加入到PCL和二苯基甲烷-4，4＇-二异氰酸酯（MDI）合成的预聚体与1，4-丁二醇扩链反应后的溶液中，制备了PU／MMT纳米复合材料。少量PCL／MMT的引入可使复合材料的综合性能大幅提高。     

Studies on thermoplastic polyurethanes based on new diphenylethane-derivative diols. II. Synthesis and characterization of segmented polyurethanes from HDI and MDI

Various new thermoplastic segmented polyurethanes were synthesized by a one-step melt polymerization from aliphatic-aromatic α,ω-diols containing sulfur in the aliphatic chain, including 4,4′-(ethane-1,2-diyl)bis(benzenethioethanol), 4,4′-(ethane-1,2-diyl)bis(benzenethiopropanol) and 4,4′-(ethane-1,2-diyl)bis(benzenethiodecanol) as chain extenders, hexane-1,6-diyl diisocyanate (HDI) or 4,4′-diphenylmethane diisocyanate (MDI) and 20-80 mol% poly(oxytetramethylene)diol (PTMO) with molecular weight of 1000 g/mol as a soft segment. The reaction was conducted at the molar ratio of NCO/OH = 1 and 1.05, and in the case of the HDI-based polyurethanes in the presence of dibutyltin dilaurate as a catalyst. The effect of the diisocyanate used on the structure and some physicochemical, thermal and mechanical properties of the segmented polyurethanes were studied. The structures of these polyurethanes were examined by FTIR and X-ray diffraction analysis. The thermal properties were investigated by differential scanning calorimetry and thermogravimetric analysis. Shore hardness and tensile properties were also determined. All the synthesized polymers showed partially crystalline structures. The MDI-based polyurethanes were products with lower crystallinity, higher glass-transition temperature (T_g) and better thermal stability in comparison with the HDI-based ones. The MDI series polymers also exhibited higher tensile strength (up to ∼36 MPa vs. ∼23 MPa) and elongation at break (up to ∼3900% vs. ∼900%), but lower hardness than the analogous HDI series polyurethanes. In both series of the polymers an increase in PTMO soft-segment content was associated with decreased crystallinity, T_g, hardness and tensile strength. An increase in PTMO content also involved an increase in elongation at break.     

新型手性聚酰胺酰亚胺的合成及其热稳定性

L-异亮氨酸与3,3’,4,4’-联苯四甲酸二酐在乙酸中回流反应制得具有联苯酰亚胺结构的手性N,N’-(4,4’-二邻苯二甲酰基)-二[(S)-(+)-异亮氨酸](3);以3和二苯基甲烷二异氰酸酯为单体,通过缩聚反应合成了新型手性聚酰胺酰亚胺(5),其结构经1H NMR和IR表征。DSC测试结果表明,5在氮气氛中5%失重温度超过370℃;600℃时残余质量为60%,显示出良好的热稳定性。