不同退火温度的Al_2O_3:C薄膜热释光和光释光性能

α-Al_2O_3:C晶体的热释光和光释光性能优越,但其制备要求高,需高温和高还原气氛.与α-Al_2O_3:C晶体性能接近的α-Al_2O_3:C陶瓷,热释光峰不单一.本文采用两次阳极氧化法在0.5 mol/L的草酸溶液中5℃恒温制备高度均匀有序的多孔Al_2O_3:C薄膜,主要研究不同退火温度对其热释光和光释光特性的影响.结果表明,经不同温度退火后的Al_2O_3:C薄膜均为非晶结构;不同退火温度的Al_2O_3:C薄膜热释光的主发光峰约在310℃左右,符合通用级动力学模型.600℃退火后的Al_2O_3:C薄膜热释光灵敏度最强,其热释光剂量曲线在1-10 Gy范围内具有很好的线性响应,在剂量10-120 Gy范围内出现超线性响应;在相同的辐照剂量下,随着退火温度的升高(≤600℃)光释光的初始发光强度逐渐增强.不同退火温度的Al_2O_3:C薄膜光释光衰减曲线都呈典型的指数衰减且快衰减速率相比α-Al_2O_3:C晶体显著加快.600℃退火后的Al_2O_3:C薄膜光释光灵敏度最强,其光释光剂量响应曲线在1-200 Gy整体上都具有很好的剂量线性关系.与热释光相比,Al_2O_3:C薄膜的光释光具有更宽的线性剂量响应范围.此研究为Al_2O_3:C薄膜作为光释光辐射剂量材料做出了有益的探索.     

Characteristics of TL and PTTL glow curves of gamma irradiated pure Li2B4O7 single crystals

The TL glow curve of X-ray irradiated pure and Cu-doped Li₂B₄O₇ shows that the most intense TL peak is at 160°C. In the present work the characteristics of the TL and PTTL glow curves from gamma irradiated pure Li₂B₄O₇ single crystal samples (prepared by Mitui Kinzoku Kougyo, Japan) have been studied. The samples were irradiated with different gamma doses (from 0.5 up to 500 Gy) using a ⁶⁰Co gamma ray source at a dose rate of 78 Gy h⁻¹. The TL glow curve shows three intense peaks (at 160°C, 260 and 305°C) and three weak ones (at 110, 140 and 220°C). The most intense TL peak is at 160°C, which agrees with the TL glow curve from X-ray irradiated samples [Kutomi Y. and Tomita A. (1990) TSEE and TL of Li₂B₄O₇:Cu single crystals. Radiat. Prot. Dosim. 33, 347–350]. The 305°C peak in gamma irradiated samples also appears to be very intense, which indicates its possible use in high-dose high-temperature dosimetry. Further, the characteristics of the PTTL glow curve have been studied as a function of ultraviolet exposure and number of repeated PTTL cycles.     

2018年7期 电子期刊

采用自蔓延燃烧法制备了不同镨掺杂浓度的12CaO·7Al₂O₃：Pr³⁺（C12A7：Pr³⁺） X射线影像存储荧光粉。在232 nm激发下,发现Pr³⁺掺杂摩尔分数为0.3%的荧光粉位于486 nm的蓝光发射峰呈现最大的发光强度。对C12A7：0.3% Pr³⁺样品进行真空热处理后,C12A7笼中的O^2-基团数量减少,同时类F⁺色心的空笼子的数量增多,导致陷阱数目增加和光激励发光强度增大。热释发光实验表明：C12A7：0.3% Pr³⁺样品中存在两个深陷阱,陷阱深度分别约为0.69 eV和0.80 eV;经过真空热处理后的C12A7：0.3% Pr³⁺荧光粉,陷阱深度变深,陷阱数目增多,光存储性能变好。当吸收的X射线剂量为5.2 Gy时,可以实现分辨率较高的X射线成像。实验结果表明,镨掺杂C12A7荧光粉在计算机X射线摄影领域有潜在的应用前景。     

Transport properties of SrCe0.95Y0.05O3−δ and its application for hydrogen separation

Transport properties of SrCe_0.95Y_0.05O_3−δ were studied by impedance spectroscopy and by measuring open-cell voltage (OCV) and gas permeation. Ionic transference numbers were determined by measuring the OCV of concentration cells and water vapor evolution of an O₂/H₂ fuel cell. We observed interfacial polarization on the basis of the I–V curves obtained by discharging a hydrogen concentration cell or an O₂/H₂ fuel cell. The observed high protonic conductivity (high proton and low oxide ion transference numbers) makes SrCe_0.95Y_0.05O_3−δ a potential material for hydrogen separation. From proton conductivity measurements, under a given hydrogen partial pressure difference of 4%/0.488%, the hydrogen permeation rate (of a dense membrane with 0.11 cm in thickness) was calculated to be ≈0.072 cm³ (STP) cm⁻² min⁻¹ at 800°C, whereas the permeation rate calculated from short-circuit current measurements was ≈0.023 cm³ (STP) cm⁻² min⁻¹ at 800°C. The difference between calculated and observed permeation rates is probably due to interfacial polarization.     

Electrical transport and superconductivity in the Al2O3-Bi2Sr1.8Ca1.2Cu2Oy and MgO-Bi2Sr1.8Ca1.2Cu2Oy composites

We have measured the resistivities of Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites with the nominal Bi₂Sr_1.8Ca_1.2Cu₂O_y volume fraction, ₂₂₁₂, ranging from 0.15 to 1.00. For the Al₂O₃-Bi₂Sr_1.8Ca_1.2Cu ₂O_y composites, we find for the samples with ₂₂₁₂≥0.6 that the superconducting transition temperature, T_c, is not disturbed by the addition of Al₂O₃. For ₂₂₁₂<0.3, no zero-resistivity state is observed. For the MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y composites, T_c is barely disturbed for the samples with ρ₂₂₁₂≥0.7. No superconducting state is observed for the samples with ρ₂₂₁₂<0.35. The variation of (300 K) with ρ₂₂₁₂ indicates a three-dimensional percolating Bi-Sr-Ca-Cu-O matrix occurring at ρ₂₂₁₂≈0.19 and ≈0.15 in Al₂O₃-Bi₂Sr_1.8Ca_1.2 Cu₂O_y and MgO-Bi₂Sr_1.8Ca_1.2Cu₂O_y, respectively. Both resistivity and magnetization measurements suggest that the reactions of Bi₂Sr_1.8Ca_1.2Cu₂O_y with MgO are weaker than with Al₂O₃.     

Optical and dosimetric properties of variously doped SrF2 crystals

Optical properties and irradiation effects of Nd³⁺-, Pr³⁺-, Tb³⁺- and Tm³⁺-doped SrF₂ crystals and their possible application to solid-state dosimetry were studied and compared to those induced in pure SrF₂ crystals. Optical absorption, thermoluminescence (TL), X- and light-induced luminescence (XL and PL) as well as optically stimulated luminescence and phototransferred TL (OSL and PTTL) were measured in the various samples. Special attention was given to effects of monochromatic vacuum ultraviolet (VUV) radiation. TL was excited in the pure and doped samples by X and β rays as well as by VUV radiation. TL peaks appeared after VUV irradiation at the same temperatures and with the same thermal activation energies as after X or β irradiation, indicating that they are due to the same processes. The VUV excitation spectra showed two maxima at about 145 and 130 nm. Comparison of the TL sensitivities of the various TL materials, showed that the sensitivity of SrF₂:Pr³⁺ was by more than an order of magnitude higher than that of the known LiF:Mg,Ti (TLD-100) phosphor. The sensitivity of pure and of the Nd, and Tb-doped SrF₂ were by a factor of 2–4 higher than that of the TLD-100 and that of SrF₂:Tm was slightly lower. The main emission bands of SrF₂:Pr³⁺ are located in a convenient spectral region between 460 and 640 nm, where most of the standard photomultipliers are sensitive. The dose dependence of the 460 K TL peak in SrF₂:Pr³⁺ is nearly linear in a wide range up to above 27 000 Gy.     

The response of thermally and optically stimulated luminescence from Al2O3:C to high-energy heavy charged particles

The thermoluminescence (TL) and optically stimulated luminescence (OSL) response of Al₂O₃ dosimeters to high-energy heavy charged particles (HCP) has been studied using the heavy ion medical accelarator at Chiba, Japan. The samples were Al₂O₃ single-crystal chips, of the type usually known as TLD-500, and Luxel^TM dosimeters (Al₂O₃:C powder in plastic) from Landauer Inc. The samples were exposed to ⁴He (150 MeV/u), ¹²C (400 MeV/u), ²⁸Si (490 MeV/u) and ⁵⁶Fe (500 MeV/u) ions, with linear energy transfer values covering the range from 2.26 to 189 keV/μm in water and doses from 1 to 100 mGy (to water). A ⁹⁰Sr/⁹⁰Y beta source, calibrated against a ⁶⁰Co secondary standard, was used for calibration purposes. For OSL, we used both continuous-wave OSL measurements (CW-OSL, using green light stimulation at 525 nm) and pulsed OSL measurements (POSL, using 532 nm stimulation from a Nd:YAG Q-switched laser). The efficiencies (η_HCP,γ) of the different HCPs at producing OSL or TL were observed to depend not only upon the linear energy transfer (LET) of the HCP, but also upon the sample type (single crystal chip or Luxel^TM) and the luminescence method used to define the signal—i.e. TL, CW-OSL initial intensity, CW-OSL total area, or POSL. Observed changes in shape of the decay curve lead to potential methods for extracting LET information of unknown radiation fields. A discussion of the results is given, including the potential use of OSL from Al₂O₃ in the areas of space radiation dosimetry and radiation oncology.     

(Lu,Y)2SiO5∶Ce3+与SrSO4∶Dy3+材料低温热释光及其测试仪器的研究

为了分析材料在低温下的陷阱能级,获得更多有关缺陷结构的信息,研制了一套由STM32微控制器为核心的低温热释光发光谱测量系统。设计了低温样品室,采用液氮冷却样品;STM32通过控制加热电流,实现样品以恒定速率升温,从而获得低温热释光发光曲线或三维热释光谱。温度测量范围为85~400 K,升温速率范围为0.1~10 K/s。设计了由STM32控制X射线及紫外光源的驱动电路,用于样品的激发。采用高灵敏度CCD实现对三维热释光谱的测量,采用单光子计数器获取二维热释光发光曲线。利用该系统测试了（Lu,Y）₂SiO₅:Ce³⁺（LYSO:Ce³⁺）单晶闪烁体与SrSO₄:Dy³⁺粉末样品的热释光谱及辐射发光光谱。观察到LYSO:Ce³⁺在108,200,380 K左右的热释光峰,发光波长位于390~450 nm之间,是明显的宽带峰。在低温下由于基质的自陷激子（STE）发射所形成的发射峰在166 K时发生猝灭。在309 K时,Ce³⁺发射峰展宽为单一发射峰;SrSO₄:Dy³⁺发光峰温度为178,385 K,发光波长由Dy³⁺离子的能级跃迁决定,在480,575,660,750 nm处呈现窄带发光峰。结果表明,系统人机交互界面友好,实验数据可靠,智能化程度高,操作简单。     

Synthesis and electron storage characteristics of isolated silver nanodots on/embedded in Al2O3 gate dielectric

Monolayer-isolated silver (Ag) nanodots with the average diameter down to 7 nm are synthesized on Al₂O₃/Si substrate by vacuum electron-beam evaporation followed by annealing at 400 °C in N₂ ambient. Metal–insulator-silicon (MIS) structures with Ag nanodots embedded in Al₂O₃ gate dielectric are fabricated. Clear electron storage effect with the flatband voltage shift of 1.3 eV is observed through capacitance–conductance and conductance–voltage measurements. Our results demonstrate the feasibility of applying Ag nanodots for nanocrystal floating-gate memory devices.     

Characterization of nonstoichiometric nickel manganite spinels NixMn3−x□3δ/4O4+δ by temperature programmed reduction

Cation deficient spinels Ni_xMn_3−x□_3δ/4O_4+δ (0≤x≤1) have been prepared by thermal decomposition of mixed oxalates Ni_x/3Mn_(3−x)/3(C₂O₄)·nH₂O in air at 623 K. They have been characterised by temperature programmed reduction (TPR) under H₂, the reaction being followed by gravimetric and powder X-ray diffraction measurements. It has been shown that TPR proceeds in several steps. The first steps correspond to the loss of nonstoichiometric oxygen leading to the formation of a stoichiometric oxide. During the following stages the manganese cations are reduced, causing the spinel structure to be destroyed, and the formation of solid solution of NiO in a cubic MnO. Subsequently, Ni²⁺ cations undergo a reduction to metallic nickel, and, finally, a mixture of nonstoichiometric MnO_1−δ and metallic nickel is formed. These oxides contain a high level of vacancies which vary with the nickel content with a maximum of δ≈1 near x=0.6. This nonstoichiometry is ascribed both to the presence of Ni³⁺ and excess of Mn⁴⁺.     

Gamma ray radiation induced visible light absorption in P-doped silica fibers at low dose levels

A CCD Fiber Optic Spectrometer has been used to monitor the gamma ray radiation induced loss in P-doped fibers at different dopant concentrations (1, 5 and 10 mol%) with a light source (an incandescent bulb with a temperature of 2800–3000 K). The range of dose rates is limited to that used in medical applications (cancer treatments), that is 0.1 to 1.0 Gray per minute (Gy/min). At low integral dose level (<2.0 Gy) four absorption peaks were observed (470, 502, 540 and 600 nm) within the visible region. It has been observed that the radiation induced loss at 470 and 600 nm depends strongly on dose rate. At dose rates of 0.2 and 0.5 Gy/min the induced loss shows nonlinear relation to the total dose. However, at high dose rate (1.0 Gy/min) and low dose rate (0.1 Gy/min) it seems to have a linear dependence with total dose. The conversion from NBOHCs to GeX centers was observed during gamma radiation at low dose rates (0.1–0.5 Gy/min). At the wavelength of 502 and 540 nm, the radiation induced losses show excellent linear relations with total dose (<2.0 Gy) with little dose rate dependence. Experimental results show that the sensitivity (induced loss (dB) per meter fiber per Gy) of 5 mol% P-doped silica fiber is more than 30 times greater than that of a standard multi-mode (MM) communication fiber. The results suggest that P-doped silica fiber is a good candidate as a sensing component in fiber optic dosimetry, especially for radiation therapy applications.     

OSL from BeO ceramics: new observations from an old material

In BeO ceramics, exposed to ionizing radiation, an intense OSL signal was observed. The properties of the signal and its behavior under various experimental conditions were investigated. It was found that the OSL signal is a composite signal and exhibits strong thermal quenching. The quenching energy was estimated as 0.5 eV. The excitation spectrum of the OSL signal was obtained as a broad peak in the region 420–550 nm with maximum around 435 nm. The possible correlation between the OSL signal and the peaks in the TL glow curve was also examined. It was interesting to observe that the highly light sensitive TL peak near 220°C does not contribute to the OSL signal. The OSL signal was found to originate from a trap near 340°C.

To check the possibility of using the material for radiation dosimetry the dose response and thermal stability of the OSL signal were also investigated. The dose response was found to be quite linear up to 10 Gy. The thermal activation energy of the OSL trap was determined as 1.7 eV using isothermal annealing and heating rate methods thus proving the suitability for dosimetry.     

Influence of the transparency of tunnel barriers in Nb/Al2O3/Al/Al2O3/Nb junctions on transport properties

The transparency of the tunnel barriers in double-barrier junctions influences the critical current density and the form of the current–voltage characteristics (IVC). Moreover, the barrier asymmetry is an important parameter, which has to be controlled in the technological process. We have performed a systematic study of the influence of the barrier transparency on critical current, I_C, and normal resistance, R_N, by preparing SIS and SINIS junctions under identical technological conditions and comparing their transport properties. We have fabricated Nb/Al₂O₃/Nb and Nb/Al₂O₃/Al/Al₂O₃/Nb devices with different current densities using a conventional fabrication process, varying pressure and oxidation time. The thickness of the Al middle electrode in all Nb/Al₂O₃/Al/Al₂O₃/Nb junctions was 6 nm. Patterning of the multilayers was done using conventional photolithography and the selective niobium etching process. The current density of SIS junctions was changed in the range from 0.5 to 10 kA/cm². At the same conditions the current density of SINIS devices revealed 1–100 A/cm² with non-hysteretic IVC and characteristic voltages, I_CR_N, of up to 200 μV. By comparing the experimental and theoretical temperature dependence of the I_CR_N product we estimated the barrier transparency and its asymmetry. The comparison shows a good agreement of experimental data with the theoretical model of tunneling through double-barrier structures in the dirty limit and provides the effective barrier transparency parameter γ_eff≈300. A theoretical framework is developed to study the influence of the barrier asymmetry on the current–phase relationship and it is proposed to determine the asymmetry parameter by measuring the critical current suppression as function of applied microwave power. The theoretical approach to determine the non-stationary properties of double-barrier junctions in the adiabatic regime is formulated and the results of calculations of the I–V characteristics are given in relevant limits. The existence and the magnitude of a current deficit are predicted as function of the barrier asymmetry.     

Thermoluminescence of natural and synthetic diopside

Diopside, a natural silicate mineral of formula CaMgSi₂O₆, has been investigated concerning its thermoluminescence (TL) and electron paramagnetic resonance (EPR) properties. Glow curves and TL vs. γ-dose were obtained irradiating natural samples to additional dose varying from 50 to 10,000 Gy. Except for a 410 °C peak found in the Al-doped artificial diopside, all the other peaks grow linearly with radiation dose, but saturate beyond 1 kGy. To investigate high-temperature effect before irradiation, measurements of TL intensity in samples annealed at 500–900 °C and then irradiated to 1 kGy γ-dose were carried out. Also the TL emission spectrum has been obtained. To compare with natural diopside, a synthetic pure polycrystal was produced and further those doped with iron, aluminum and manganese were also produced.     

Ionic conduction and dielectric relaxation in Ag/Na ion-exchanged aluminosilicate glasses: mixed mobile ion effect and KWW relaxation

Ag⁺/Na⁺ ion-exchanged aluminosilicate glasses with uniform concentration profiles were prepared, and their electrical conductivities were investigated as functions of the ion-exchange ratio and the initial glass compositions. In the case of the ion-exchanged glasses of x20Ag₂O–(1−x)20Na₂O–10Al₂O₃–70SiO₂ in mol%, the conductivity, σ, and its activation energy, E_σ, showed a minimum and a maximum at the same ion-exchange ratio x=0.3, respectively, and the mixed mobile ion effect (MMIE) was observed. The fully ion-exchanged sample attained σ=3.5×10⁻⁵ S/cm at 200 °C, which was 1.5 orders of magnitude larger than that of initial glass. In the case of x25Ag₂O–(1−x)25Na₂O–25Al₂O₃–50SiO₂, the mixed mobile ion effect was also observed at x=0.5. The maximum conductivity of 2×10⁻⁴ S/cm at 200 °C was obtained in the fully ion-exchanged glass sample.

The electric relaxation analysis was also conducted on both systems, and Kohlrausch–Williams–Watts (KWW) fractional exponent β was obtained as a function of x. The decrease of β was observed near x≈0.3 in the former system, while that of the later system was independent of the ion-exchange ratio. Based on the structural analysis results, the observed behaviors were investigated from the point of view of the occupation of Ag⁺ ions on the non-bridging oxygen-site (NBO-site) and the charge compensation-site (CC-site) of AlO₄ tetrahedral unit.     

The effects of deep trap population on the thermoluminescence of Al2O3:C

The influence of deep traps on the 450 K thermoluminescence (TL) peak of Al₂O₃:C is studied. Depending upon the sample and on the degree of deep trap filling, features such as the TL width, area and height can vary considerably. These effects are interpreted to be due to: (a) sensitivity changes introduced by competition mechanisms involving deep electron and hole traps, and (b) the multiple component nature of the 450 K TL peak. The influence of the deep traps on the TL was studied using different excitation sources (beta irradiation or UV illumination), and step annealing procedures. Optical absorption measurements were used to monitor the concentration of F- and F⁺-centers. The data lead to the suggestion that the competing deep traps which become unstable at 800–875 K are hole traps, and that the competing deep traps which become unstable at 1100–1200 K are electron traps. Both the dose response of the TL signal and the TL sensitivity are shown to be influenced by sensitization and desensitization processes caused by the filling of deep electron and hole traps, respectively. Changes in the TL peak at low doses were also shown to be connected to the degree of filling of deep traps, emphasizing the influence of deep trap concentration and dose history of each sample in determining the TL properties of the material. Implications of these results for the optically stimulated luminescence properties are also discussed.     

Thermodynamic properties of the clathrate-type silver-oxide Ag6O8AgHF2

We report normal-state and superconducting properties of the clathrate-type silver-oxide Ag₆O₈AgHF₂. We present electrical resistivity, DC- and AC-susceptibility and specific-heat measurements of single crystalline Ag₆O₈AgHF₂. In the normal state, Ag₆O₈AgHF₂ exhibits metallic conductivity and a phase transition near 110 K, possibly a structural phase transition as observed in the related compound Ag₆O₈AgNO₃. The onset of superconductivity of our samples is observed around 1.2–1.5 K, and the H–T phase diagram is determined for the first time. The upper critical field H_c2(0) is estimated to be about 2000–2200 Oe and the coherence length ξ_GL(0) to be 40 nm.     

Enhanced luminescence from transparent Ni-doped MgO–Al2O3–SiO2 glass ceramics by Ga2O3 addition

Transparent Ni²⁺-doped MgO–Al₂O₃–SiO₂ glass ceramics without and with Ga₂O₃ were synthetized. The precipitation of spinel nanocrystals, which was identified as solid solutions in the glass ceramics, could be favored by Ga₂O₃ addition and their sizes were about 7.6 nm in diameter. The luminescent intensity of the Ni²⁺-doped glass ceramics was largely enhanced by Ga₂O₃ addition which could mainly be caused by increasing of Ni²⁺ in the octahedral sites and the reduction of the mean frequency of phonon density of states in the spinel nanocrystals of solid solutions. The full width at half maximum (FWHM) of emissions for the glass ceramics with different Ga₂O₃ content was all more than 200 nm. The emission lifetime increased with the Ga₂O₃ content and the longest lifetime is about 250 μs. The Ni²⁺-doped transparent glass ceramics with Ga₂O₃ addition have potential application as broadband optical amplifier and laser materials.     

Evidence for pinning by (Sr,Ca)2CuOy particles in partial-melting processed bulk Bi2Sr2CaCu2O8+δ ceramics

Flux distributions of partial-melting processed Bi₂Sr₂CaCu₂O_8+δ ceramics are obtained using magneto-optic imaging. In remanent states (μ₀H_a=0 T), large amounts of trapped flux are observed along (Sr,Ca)₂CuO_y particles embedded in the Bi₂Sr₂CaCu₂O_8+δ matrix. Despite the relatively large size of these particles (up to 30 μm), the pinning effect is similar to that of Y₂BaCuO₅ particles in melt-processed YBa₂Cu₃O_7−δ. Furthermore, we discuss how the pinning capability of non-superconducting particles of different sizes and densities will show up in magneto-optic images.     

The effects of substrate temperature on the superconducting properties of Tl2Ca2Ba2Cu3O10 films sputter-deposited from stoichiometric oxide targets

The annealing characteristics and the superconducting properties of Tl₂Ca₂Ba₂Cu₃O₁₀ thin films sputter-deposited onto yttrium- stabilized ZrO₂ substrate at up to 500°C from two stoichiometric oxide targets are reported. The films deposited at 400–500°C were found to require a lower post-annealing temperature than the films deposited at lower temperatures to attain the highest T_c superconducting state, due to a more pronounced Ba diffusion toward the substrate as indicated by their secondary ion mass spectrometry depth profiles. The highest T_c achieved tends to degrade with increasing substrate temperatures, a zero resistance T_c of 121 and ≈90 K, respectively, being observed for the films deposited at -ambient temperature and at 500°C. The formation of the highest T_c phase (Tl₂Ca₂Ba₂Cu₃O₁₀) generally is associated with a sheet type of crystal growth morphology with smooth and aligned surfaces which can be obtained only from the films capable of sustaining prolonged annealing at 900°C. Annealing at lower temperatures (≈860°C) results in the formation of rod or sphere type of morphologies with rough and randomly oriented crystals and the lower T_c phases such as Tl₂Ca₁Ba₂Cu₂O₈.