Synthesis and characterization of low‐bandgap cyclopentadithiophene‐biselenophene copolymer and its use in field‐effect transistor and polymer solar cells

Novel series of conjugated copolymers, incorporating cyclopentadithiophene (CPDT) and the biselenophene ( R‐CPDT‐Se2 ), were synthesized by Pd‐catalyzed Stille coupling polymerization. The optical, electrochemical, field‐effect carrier mobilities, and photovoltaic properties of the R‐CPDT‐Se2 were investigated and compared with cyclopentadithiophene (CPDT) and the bithiophene ( EHex‐CPDT‐T2 ). The highest hole mobility of thin film transistor devices fabricated with new p‐type polymer semiconductors, Oct‐CPDT‐Se2 , was 1.3 × 10^?3 cm²/Vs with an on/off ratio of about 10⁵. The maximum power conversion efficiency of polymer solar cell fabricated with the blend of EHex‐CPDT‐Se2 /C₇₁‐PCBM reached 1.86% with an open circuit voltage (V_OC) of 0.55 V, a short circuit current density (J_sc) of 7.27 mA/cm², and a fill factor (FF) of 0.47 under AM 1.5G irradiation (100 mW/cm²). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2009     

Synthesis and applications of cyano‐vinylene‐based polymers containing cyclopentadithiophene and dithienosilole units for photovoltaic cells

Two β‐cyano‐thiophenevinylene‐based polymers containing cyclopentadithiophene ( CPDT‐CN ) and dithienosilole ( DTS‐CN ) units were synthesized via Stille coupling reaction with Pd(PPh₃)₄ as a catalyst. The effects of the bridged atoms (C and Si) and cyano‐vinylene groups on their thermal, optical, electrochemical, charge transporting, and photovoltaic properties were investigated. Both polymers possessed the highest occupied molecular orbital (HOMO) levels of about ?5.30 eV and the lowest unoccupied molecular orbital (LUMO) levels of about ?3.60 eV, and covered broad absorption ranges with narrow optical band gaps (ca. 1.6 eV). The bulk heterojunction polymer solar cell (PSC) devices containing an active layer of electron‐donor polymers ( CPDT‐CN and DTS‐CN ) blended with an electron‐acceptor, that is, [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM), in different weight ratios were explored under 100 mW/cm² of AM 1.5 white‐light illumination. The PSC device based on DTS‐CN: PC₇₁BM (1:2 w/w) exhibited a best power conversion efficiency (PCE) value of 2.25% with V_oc = 0.74 V, J_sc = 8.39 mA/cm², and FF = 0.36. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Synthesis and photovoltaic properties of copolymers based on bithiophene and bithiazole

Three simple structured D‐A copolymers, PBTBTz‐1 , PBTBTz‐2 , and PBTBTz‐3 , containing bithiophene (BT) donor unit and bithiazole (BTz) acceptor unit with different alkyl chain length were synthesized by the Pd‐catalyzed Stille‐coupling method. The copolymers were characterized by thermogravimetric analysis, UV–vis absorption, electrochemical cyclic voltammetry, and photovoltaic measurements. The results indicate that the introduction of BTz unit to the polythiophene main chain effectively decreases highest occupied molecular orbital levels of the copolymers and increases the open circuit voltage (V_oc) of polymer solar cells (PSCs) based on the copolymers as donor, and the alkyl chain length influences the photovoltaic properties of the polymers significantly. The PSCs based on PBTBTz‐2 and PBTBTz‐3 show higher V_oc up to 0.77 and 0.81 V, respectively. The power conversion efficiency of the PSC based on PBTBTz‐2 :PC₇₀BM = 1:1(w/w) reached 2.58% with short circuit current of 8.70 mA/cm², under the illumination of AM1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and applications of 2,7‐carbazole‐based conjugated main‐chain copolymers containing electron deficient bithiazole units for organic solar cells

A series of low‐band‐gap (LBG) donor–accepor conjugated main‐chain copolymers ( P1 – P4 ) containing planar 2,7‐carbazole as electron donors and bithiazole units (4,4′‐dihexyl‐2,2′‐bithiazole and 4,4′‐dihexyl‐5,5′‐di(thiophen‐2‐yl)‐2,2′‐bithiazole) as electron acceptors were synthesized and studied for the applications in bulk heterojunction (BHJ) solar cells. The effects of electron deficient bithiazole units on the thermal, optical, electrochemical, and photovoltaic (PV) properties of these LBG copolymers were investigated. Absorption spectra revealed that polymers P1 – P4 exhibited broad absorption bands in UV and visible regions from 300 to 600 nm with optical band gaps in the range of 1.93–1.99 eV, which overlapped with the major region of the solar emission spectrum. Moreover, carbazole‐based polymers P1 – P4 showed low values of the highest occupied molecular orbital (HOMO) levels, which provided good air stability and high open circuit voltages (V_oc) in the PV applications. The BHJ PV devices were fabricated using polymers P1 – P4 as electron donors and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₁BM) or (6,6)‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) as electron acceptors in different weight ratios. The PV device bearing an active layer of polymer blend P4:PC₇₁BM (1:1.5 w/w) showed the best power conversion efficiency value of 1.01% with a short circuit current density (J_sc) of 4.83 mA/cm², a fill factor (FF) of 35%, and V_oc = 0.60 V under 100 mW/cm² of AM 1.5 white‐light illumination. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Reduced‐bandgap triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene copolymers pending benzothiadiazole or diketopyrrolopyrrole units for efficient polymer solar cells

Two new side‐chain donor–acceptor (D‐A)‐based triphenylamine‐alt‐benzo[1,2‐b:4,5‐b′]dithiophene (TPA‐alt‐BDT) copolymers ( P1 and P2 ) with pendant benzothiadiazole (BT)/diketopyrrolopyrrole (DPP) in TPA unit were synthesized by Stille coupling polymerization. Their thermal, photophysical, electrochemical, blend film morphology and photovoltaic properties were investigated. Efficient bulk heterojunction polymer solar cells (PSCs) were obtained by solution process using both copolymers as donor materials and PC₇₁BM as acceptor. The maximum power conversion efficiency (PCE) of 3.17% with a highest open‐circuit voltage (V_oc) of 0.86V was observed in the P1 ‐based PSCs, while the maximum short‐circuit current (J_sc) of 10.77 mA cm^?2 was exhibited in the P2 ‐based PSCs under the illumination of AM 1.5, 100 mW cm^?2. The alternating binary donor units and pending acceptor groups played a significant role in tuning photovoltaic properties for this class of the side‐chain D–A‐based copolymers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4103–4110     

Synthesis and characterization of fluorene and cyclopentadithiophene‐based copolymers exhibiting broad absorption for photovoltaic devices

In this study, two low bandgap copolymers composed of fluorene (Fl), cyclopentadithiophene (CDT), and 4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole (DBT) were synthesized, and their optical, electrochemical, and photovoltaic (PV) characteristics were investigated for applications in PV devices. The feed ratio of the Fl and CDT moieties was modulated to tune the electronic structures and resulting optical properties of the polymers. In the copolymeric structures, the Fl‐CDT unit absorbs the short‐wavelength UV/vis regions, and the CDT‐DBT (or Fl‐DBT) unit with strong intramolecular charge transfer characteristics covers the long‐wavelength visible regions. P1 exhibited a wide UV absorption spectrum covering the UV and entire visible region in the range of 300–800 nm, and P2 showed absorption covering from 300 to 700 nm. UV/vis and electrochemical studies confirmed the desirable highest occupied molecular orbital/lowest unoccupied molecular orbital levels of the copolymers with bandgaps of 1.62–1.86 eV, enabling efficient electron transfer and a high open‐circuit voltage when blending them with fullerene derivatives. When the polymers were blended with [6,6]phenyl‐C₆₁‐butyric acid methyl ester, P1 exhibited the best device performance with an open‐circuit voltage of 0.66 V, short‐circuit current of 4.92 mA cm^?2, and power conversion efficiency of 1.13% under Air Mass 1.5 Global (AM 1.5G, 100 mW cm^?2) illumination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and photovoltaic properties of two‐dimensional D‐A copolymers with conjugated side chains

Four novel two‐dimensional (2D) donor–acceptor (D‐A) type copolymers with different conjugated side chains, P1 , P2 , P3 , and P4 (see Fig. 1 ), are designed and synthesized for the application as donor materials in polymer solar cells (PSCs). To the best of our knowledge, there were few reports to systematically study such 2D polymers with D‐A type main chains in this area. The optical energy band gaps are about 2.0 eV for P1 – P3 and 1.67 eV for P4 . PSC devices using P1 – P4 as donor and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester as acceptor in a weight ratio of 1:3 were fabricated and characterized to investigate the photovoltaic properties of the polymers. Under AM 1.5 G, 100 mA/cm² illumination, a high open‐circuit voltage (V_oc) of 0.9 V was recorded for P3 ‐based device due to its low HOMO level, and moderate fill factor was obtained with the best value of 58.6% for P4 ‐based device, which may mainly be the result of the high hole mobility of the polymers (up to 1.82 × 10^?3 cm²/V s). © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Novel low‐bandgap oligothiophene‐based donor‐acceptor alternating conjugated copolymers: Synthesis,properties, and photovoltaic applications

A series of novel soluble donor‐acceptor low‐bandgap‐conjugated polymers consisting of different oligothiophene (OTh) coupled to electron‐accepting moiety 2‐pyran‐4‐ylidenemalononitrile (PM)‐based unit were synthesized by Stille or Suzuki coupling polymerization. The combination of electron‐accepting PM building block with varied OTh_n (the number of thiophene unit increases from 3 to 5) results in enhanced π–π stacking in solid state and intramolecular charge transfer (ICT) transition, which lead to an extension of the absorption spectra of the copolymers. Cyclic voltammetry measurements and molecular orbital distribution calculations indicate that the highest occupied molecular orbitals (HOMO) energy levels could be fine‐tuned by changing the number of thiophene units of the copolymers, and the resulting copolymers possessed relatively low HOMO energy levels promising good air stability and high‐open circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction photovoltaic devices were fabricated by using the copolymers as donors and (6,6)‐phenyl C₆₁‐butyric acid methyl ester as acceptor. It was found that the highest V_oc reached 0.94 V, and the short circuit currents (J_sc) were improved from 1.78 to 2.54 mA/cm², though the power conversion efficiencies of the devices were measured between 0.61 and 0.99% under simulated AM 1.5 solar irradiation of 100 mW/cm², which indicated that this series copolymers can be promising candidates for the photovoltaic applications. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2765–2776, 2010     

Side‐chain effects on phenothiazine‐based donor–acceptor copolymer properties in organic photovoltaic devices

A series of new phenothiazine‐based donor–acceptor copolymers, P1 and P2, were synthesized via a Suzuki coupling reaction. The weight‐averaged molecular weights (M_w) of P1 and P2 were found to be 16,700 and 16,100, with polydispersity indices of 1.74 and 1.39, respectively. The UV–visible absorption spectra of the polymer thin films contained three strong absorption bands in the ranges 318–320 nm, 430–436 nm, and 527–568 nm. The absorption peaks at 320 and 430 nm originated mainly from the phenothiazine‐based monomer units, and the longer wavelength absorption band at 527–568 nm was attributed to the increased effective conjugation length of the polymer backbones. Solution‐processed field‐effect transistors fabricated with these polymers exhibited p‐type organic thin film transistor characteristics. The field‐effect mobilities of P1 and P2 were measured to be 1.0 × 10^?4 and 7.5 × 10^?5 cm² V^?1 s^?1, respectively, with on/off ratios in the order of 10⁴ for all polymers. A photovoltaic device in which a P2/PC₇₁BM (1/3) blend film was used as the active layer exhibited an open‐circuit voltage (V_OC) of 0.70 V, a short‐circuit current (J_SC) of 6.79 mA cm⁽², a fill factor of 0.39, and a power conversion efficiency of 1.86% under AM 1.5 G (100 mW cm^?2) illumination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and characterization of new light‐emitting copolymers in polymeric‐light‐emitting‐diode device fabrications

A series of thiophene‐containing photoactive copolymers consisting of alternating conjugated and nonconjugated segments were synthesized. The ¹H NMR spectra corroborated the well‐defined structures, and the copolymers not only were soluble in common organic solvents but also had high glass‐transition temperatures (ca. 130 °C) and good thermal stability up to 390 °C. Introducing aliphatic functional groups, such as alkyl or alkoxyl, into chromophores of the copolymers redshifted the photoluminescence spectra and lowered the optical bandgaps. The electrochemical bandgaps calculated from cyclic voltammetry agreed with the optical bandgaps and thus indicated that electroluminescence and photoluminescence originated from the same excited state. The energy levels (highest occupied molecular orbital and lowest unoccupied molecular orbital) of all the copolymers were lower than those of poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐1.4‐phenylenevinylene] MEH–PPV, indicating balanced hole and electron injection, which led to improved performance in both single‐layer and double‐layer polymeric‐light‐emitting‐diode devices fabricated with these copolymers. All the copolymers emitted bluish‐green or green light above the threshold bias of 5.0 V under ambient conditions. At the maximum bias of 10 V, the electroluminescence of a device made of poly(2‐{4‐[2‐(3‐ethoxy phenyl)ethylene]phenyl}‐5‐{4‐[2‐(3‐ethoxy,4‐1,8‐octanedioxy phenyl)ethylene]phenyl}thiophene) was 5836 cd/m². The external electroluminescence efficiency decreased with the lifetime as the polymer degraded. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3954–3966, 2004     

Synthesis and Photovoltaic Properties of Thieno[3,4‐c]pyrrole‐4,6‐dione‐based donor–acceptor Copolymers

Three donor–acceptor (D–A) 1,3‐di(thien‐2‐yl)thieno [3,4‐c]pyrrole‐4,6‐dione‐based copolymers, poly{9,9‐dioctylfluorene‐2,7‐diyl‐alt‐1,3‐bis(4‐hexylthien‐2‐yl)‐5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}, poly{N‐(1‐octylnonyl)carbazole‐2,7‐diyl‐alt‐1,3‐bis(4‐hexylthien‐2‐yl)‐5‐octylthieno[3,4‐c]pyrrole‐4,6‐dione}, and poly {4,8‐bis(2‐ethylhexyloxyl) benzo[1,2‐b:3,4‐b′]dithiophene‐alt‐1,3‐bis(4‐hexylthien‐2‐yl)‐5‐octylthieno[3,4‐c] pyrrole‐4,6‐dione} were synthesized by Suzuki or Stille coupling reaction. By changing the donor segment, the bandgaps and energy levels of these copolymers could be finely tuned. Cyclic voltammetric study shows that the highest occupied molecular orbital (HOMO) energy levels of the three copolymers are deep‐lying, which implies that these copolymers have good stability in the air and the relatively low HOMO energy level assures a higher open‐circuit potential when they are used in photovoltaic cells. Bulk‐heterojunction photovoltaic cells were fabricated with these polymers as the donors and PC₇₁BM as the acceptor. The cells based on the three copolymers exhibited power conversion efficiencies of 0.22, 0.74, and 3.11% with large open‐circuit potential of 1.01, 0.99, and 0.90 V under one sun of AM 1.5 solar simulator illumination (100 mW/cm²). © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Pyrrolo[3,4‐c]pyrrole‐1,3‐dione‐based large band gap polymers containing benzodithiophene derivatives for highly efficient simple structured polymer solar cells

Pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (DPPD)‐based large band gap polymers, P(BDT‐TDPPDT) and P(BDTT‐TDPPDT), are prepared by copolymerizing electron‐rich 4,8‐bis(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene (BDT) or 4,8‐bis(5‐(2‐ethylhexyl)thiophen‐2‐yl)benzo[1,2‐b:4,5‐b′]dithiophene (BDTT) unit with novel electron deficient 2,5‐dioctyl‐4,6‐di(thiophen‐2‐yl)pyrrolo[3,4‐c]pyrrole‐1,3(2H,5H)‐dione (TDPPDT) unit. The absorption bands of polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) cover the region from 300 to 600 nm with an optical band gap of 2.11 eV and 2.04 eV, respectively. The electrochemical study illustrates that the highest occupied/lowest unoccupied molecular orbital energy levels of P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) are ?5.39 eV/?3.28 eV and ?5.44 eV/?3.40 eV, respectively. The single layer polymer solar cell (PSC) fabricated with a device structure of ITO/PEDOT:PSS/P(BDT‐TDPPDT) or P(BDTT‐TDPPDT):PC70BM+DIO/Al offers a maximum power conversion efficiency (PCE) of 6.74% and 6.57%, respectively. The high photovoltaic parameters such as fill factor (～72%), open circuit voltage (V_oc, ～0.90 V), incident photon to collected electron efficiency (～76%), and PCE obtained for the PSCs made from polymers P(BDT‐TDPPDT) and P(BDTT‐TDPPDT) make them as promising large band gap polymeric candidates for PSC application. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3564–3574     

Tuning the frontier molecular orbital energy levels of n‐type conjugated copolymers by using angular‐shaped naphthalene tetracarboxylic diimides,and their use in all‐polymer solar cells with high open‐circuit voltages

An angular‐shaped naphthalene tetracarboxylic diimide (NDI) was designed and synthesized as a new building block for n‐type conjugated polymers to tune their energy levels. Three n‐type copolymers incorporating this angular‐shaped NDI as the acceptor moiety were obtained by Stille coupling reactions and had number average molecular weights of 18.7–73.0 kDa. All‐polymer bulk‐heterojunction solar cells made from blends of these polymers with poly(3‐hexylthiophene) gave a power conversion efficiency up to 0.32% and exhibited an open‐circuit voltage (V_oc) up to 0.94 V due to their relative high‐lying lowest unoccupied molecular orbital energy levels. The high V_oc of 0.94 V is higher than that of solar cells based on linear‐shaped NDI‐containing polymers (<0.6 V). The results indicate that the angular‐shaped NDI is a promising building block for constructing nonfullerene polymer acceptors for solar cells with high open‐circuit voltages. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis,photophysics, and electroluminescent performance of stable blue‐light‐emitting copoly(9,9‐diarylfluorene)s

A series of fluorene derivatives containing nonsymmetric and bulky aromatic groups at C‐9 position were synthesized and used for the preparation of blue‐light‐emitting copolyfluorenes ( P1 – P4 ) by the Suzuki coupling polycondensation. The copolymers were characterized by molecular weight determination, elemental analysis, differential scanning calorimeter, thermogravimetric analysis, absorption and emission spectroscopy, cyclic voltammetry, and differential pulse voltammetry. Their decomposition temperatures and glass transition temperatures are 423–441 °C and >120 °C, respectively. In film state, the copolyfluorenes exhibit blue photoluminescence at 425–450 nm, which remains almost unchanged after annealing at 200 °C in air for 60 min. Polymer light‐emitting diodes [ITO/PEDOT:PSS/ P1 – P4 /Ca(50 nm)/Al(100 nm)] show stable blue‐light emission under device operation with the CIE co‐ordinates being between (0.16, 0.07) and (0.17, 0.09). The light‐emitting diodes devices from P1 and P3 containing electron‐deficient oxadiazole units display enhanced performance, with the maximum brightness and maximum current efficiency being (4510 cd/m² and 2.40 cd/A) and (2930 cd/m², 1.19 cd/A), respectively. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2821–2834, 2009     

Novel narrow‐band‐gap conjugated copolymers containing phenothiazine‐arylcyanovinyl units for organic photovoltaic cell applications

A series of novel narrow‐band‐gap copolymers ( P1 ‐ P12 ) composed of alkyl‐substituted fluorene (FO) units and six analogous mono‐ and bis(2‐aryl‐2‐cyanovinyl)‐10‐hexylphenothiazine monomers ( M1 ‐ M6 ) were synthesized by a palladium‐catalyzed Suzuki coupling reaction with two different feed in ratios of FO to M1 ‐ M6 (molar ratio = 3:1 and 1:1). The absorption spectra of polymers P1 ‐ P12 exhibited broad peaks located in the UV and visible regions from 400 to 800 nm with optical band gaps at 1.55–2.10 eV, which fit near the wavelength of the maximum solar photon reflux. Electrochemical experiments displayed that the reversible p‐ and n‐doping processes of copolymers were partially reversible, and the proper HOMO/LUMO levels enabled a high photovoltaic open‐circuit voltage. As blended with [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) as an electron acceptor in bulk heterojunction photovoltaic devices, narrow‐band‐gap polymers P1 ‐ P12 as electron donors showed significant photovoltaic performance which varied with the intramolecular donor‐acceptor interaction and their mixing ratios to PCBM. Under 100 mW/cm² of AM 1.5 white‐light illumination, the device of copolymer P12 produced the highest preliminary result having an open‐circuit voltage of 0.64 V, a short‐circuit current of 2.70 mA/cm², a fill factor of 0.29, and an energy conversion efficiency of 0.51%. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4285–4304, 2008     

Influence of 4‐fluorophenyl pendants in thieno[3,4‐b]thiophene‐benzo[1,2‐b:4,5‐b′]dithiophene‐based polymers on the performance of photovoltaics

Polymers consisting of benzo[1,2‐b:4,5‐b′]dithiophene and thieno[3,4‐b]thiophene units (PTB‐based polymers), either fully or partially containing 4‐fluorophenyl pendants, are synthesized as electron donor materials for inverted‐type polymer solar cells (PSCs). The influence of the 4‐fluorophenyl pendant content on the thermal and optical properties, the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO), the hole mobilities, and photovoltaic performances are investigated. As the 4‐fluorophenyl pendant content increased, the HOMO and LUMO of the polymers were deepened proportionally and the open‐circuit voltages of the PSCs improved. Incorporation of 4‐fluorophenyl pendants into the polymers also affected the crystallinity, orientation, and compatibility with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester in the active layers, leading to nonlinearities in the short‐circuit current densities, and fill factors. The incorporation of an appropriate number of 4‐fluorophenyl pendants enhanced the power conversion efficiencies of the PSC devices from 2.25 to 3.96% for identical device configurations. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1586–1593     

Electroluminescent copolymers based on dihexylfluorene and 2‐{2,6‐bis[2‐(4‐diphenylaminophenyl)vinyl]pyran‐4‐ylidene}malononitrile units

A series of statistical copolymers (poly[(9,9‐di‐n‐hexylfluorene)‐co‐2‐{2,6‐bis‐[2‐(4‐diphenylaminophenyl)vinyl]pyran‐4‐ylidene}malononitrile) were synthesized by the Suzuki coupling reaction. The copolymers showed absorption bands at 379 and 483–489 nm, which were attributed to the oligofluorene segments and the segments containing 2‐[2,6‐bis(2‐{4‐[(4‐bromophenyl)phenylamino]phenyl}vinyl)pyran‐4‐ylidene]malononitrile ( 3 ), respectively. The absorption band around 483–489 nm increased with the feed ratio of 3 . The photoluminescence (PL) spectra of the copolymers showed emission bands at 420 and 573–620 nm. As the feed ratio of 3 increased, the PL emission in the longer wavelength region redshifted, and the intensity increased as well. The electroluminescence (EL) spectrum of the copolymers showed a very weak emission at 420 nm. The PL and EL emission colors redshifted dramatically with the increase in the feed ratio of 3 . The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of the model compound (2‐{2,6‐bis[2‐(4‐diphenylaminophenyl)vinyl]pyran‐4‐ylidene}malononitrile) were determined to be ?5.34 and ?3.14 eV, respectively. It was concluded that energy transfer took place from the oligofluorene blocks to the segments containing 3 and that direct charge trapping occurred in the segments containing 3 during the EL operation. The Commission Internationale de l'Eclairage (CIE) chromaticity coordinates of the copolymer (x = 0.63, y = 0.37) containing 10 mol % 3 were very close to those (x = 0.67, y = 0.33) for National Television System Committee (NTSC) red with a maximum photometric power efficiency of 0.27 cd/A. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3729–3737, 2006     

Dithienosilole–phenylquinoxaline‐based copolymers with A‐D‐A‐D and A‐D structures for polymer solar cells

Two copolymers having D‐A‐D‐A ( P1 ) and D‐A ( P2 ) structures with quinoxaline acceptor unit and dithienosilole donor unit were synthesized and their optical and electrochemical (both experimental and theoretical) properties were investigated. The optical properties showed that these copolymers P1 and P2 exhibit optical bandgaps of 1.54 and 1.62 eV, respectively, with broader absorption profiles extending up to 800 nm and 770 nm, respectively. The electrochemical investigation of these two copolymers indicates that they exhibit suitable highest occupied molecular orbital and lowest unoccupied molecular orbital energy levels for efficient exciton dissociation and high open circuit voltage in the resultant polymer solar cells (PSCs). These copolymers were used as donors along with the PC₇₁BM as acceptor for the fabrication of solution processed bulk heterojunction PSCs. The optimized P1 :PC₇₁BM and P2 :PC₇₁BM active layers treated with solvent vapor treatment showed overall power conversion efficiency (PCE) of 7.16% and 6.57%, respectively. The higher PCE of P1 ‐based device as compared to P2 might be attributed to higher crystallinity of P1 and good hole mobility resulting more balanced charge transport. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 376–386     

Conjugated polymers based on dicarboxylic imide‐substituted isothianaphthene and their applications in solar cells

Four new polymers containing a benzo[c]thiophene‐N‐dodecyl‐4,5‐dicarboxylic imide (DIITN) unit including the homopolymer and three donor–acceptor copolymers were designed, synthesized, and characterized. For these copolymers, DIITN unit with low bandgap was selected as an electron acceptor, whereas 5,5′‐(2,7‐bisthiophen‐2‐yl)‐9‐(2‐decyltetradecyl)‐9H‐carbazole), 5,5′‐(3,3′‐di‐n‐octylsilylene‐2,2′‐bithiophene), and 5,5′‐(2,7‐bisthiophen‐2‐yl‐9,9‐bisoctyl‐9H‐fluoren‐7‐yl) were chosen as the electron donor units to tune the highest occupied molecular orbital/lowest unoccupied molecular orbital (HOMO/LUMO) levels of the copolymers for better light harvesting. These polymers exhibit extended absorption in the visible and near‐infrared range and are soluble in common organic solvents. The relative low lying HOMO of these polymers promises good air stability and high open‐circuit voltage (V_oc) for photovoltaic application. Bulk heterojunction solar cells were fabricated by blending the copolymers with [6,6]‐phenyl‐C61‐butyric acid methyl ester or [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC71BM). The best power conversion efficiency of 1.6% was achieved under simulated sunlight AM 1.5G (100 mW/cm²) from solar cells containing 20 wt % of the fluorene copolymer poly[5,5′‐(2,7‐bisthiophen‐2‐yl‐9,9‐bisoctyl‐9H‐fluoren‐7‐yl)‐alt‐2,9‐(benzo[c]thiophene‐N‐dodecyl‐4,5‐dicarboxylic imide)] and 80 wt % of PC71BM with a high open‐circuit voltage (V_oc) of 0.84 V. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and photovoltaic properties of low‐bandgap 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole‐based poly(heteroarylenevinylene)s

Three novel low‐bandgap copolymers containing alkylated 4,7‐dithien‐2‐yl‐2,1,3‐benzothiadiazole (HBT) and different electron‐rich functional groups (dialkylfluorene (PFV‐HBT), dialkyloxyphenylene (PPV‐HBT) and dialkylthiophene (PTV‐HBT)) were prepared by Horner polycondensation reactions and characterized by ¹H NMR, gel permeation chromatography, and elemental analysis. The alkyl side chain brings these polymeric materials good solubility in common organic solvents, which is critical for the manufacture of solar cells in a cost‐effective manner. The copolymers exhibit low optical bandgap from 1.48 to 1.83 eV. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the copolymers were measured by cyclic voltammetry. Theoretical calculations revealed that the variation laws of HOMO and the LUMO energy levels are well consistent with cyclic voltammetry measurement. The bulk heterojunction photovoltaic devices with the structure of ITO/PEDOT‐PSS/polymer:PCBM/LiF/Al were fabricated by using the three copolymers as the donor and (6,6)‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) as the acceptor in the active layer. The device based on PTV‐HBT:PCBM (1:4 w/w) achieved a power conversion efficiency of 1.05% under the illumination of AM 1.5, 100 mW/cm². © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.