Interactions of carbon nanotubes with pyrene‐functionalized linear‐dendritic hybrid polymers

A series of linear‐dendritic hybrid polymers, containing pyrene units at the periphery of aliphatic polyester dendrons, were prepared for the purpose of dispersing shortened single‐walled carbon nanotubes (SWNTs) in tetrahydrofuran (THF). The prepared hybrids contained 1, 2, 4, 8, or 16 (G0 through G4) pyrene units and a linear segment composed of polystyrene. It was found that a minimum of four pyrene units was necessary to form a strong enough interaction with SWNTs to enable steric stabilization in solution, when using a linear polymer segment of 11.5 kDa. Increasing either the number of pyrene units per polymer chain or the length of the polymer segment to 18.0 kDa did not improve nanotube solubility, whereas decreasing the polymer length resulted in significantly less effective nanotube dissolution. The G4 dendron alone, without the linear polystyrene segment, was also found to impart solubility to the nanotubes in THF. Interactions between the series of linear‐dendritic hybrids and full‐length multiwalled carbon nanotubes were also investigated, and it was found that the polymers exhibited strong interactions with the multiwalled carbon nanotube surface, resulting in the formation of stable solutions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1016–1028, 2010     

Multiarm star polymers with peripheral dendritic PMMA arms through Diels–Alder click reaction

Dendritic 2‐ and 4‐arm PMMA‐based star polymers with furan‐protected maleimide at their focal point, (PMMA)_2n‐MI and (PMMA)_4n‐MI were efficiently clicked with the peripheral anthracene functionalized multiarm star polymer, (α‐anthryl functionalized‐polystyrene)_m‐poly(divinyl benzene) ((α‐anthryl‐PS)_m‐polyDVB) through the Diels–Alder reaction resulting in corresponding multiarm star block copolymers: (PMMA)_2n‐(PS)_m‐polyDVB and (PMMA)_4n‐(PS)_m‐polyDVB, respectively. Molecular weights (M_w,TDGPC), hydrodynamic radius (R_h), and intrinsic viscosity (η) of the multiarm star polymers were determined using three‐detection GPC (TD‐GPC). The high efficiency of this methodology to obtain such sterically demanding macromolecular constructs was deduced using ¹H‐NMR and UV–vis spectroscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Dispersion of single‐walled carbon nanotubes using nucleobase‐containing poly(acrylamide) polymers

Single‐walled carbon nanotubes (SWNTs) possess extraordinary properties, but suffer from poor solubility and a lack of purity. Of the possible routes available to solubilize and purify nanotube samples, the use of noncovalent functionalization is ideal as carbon nanotube properties are not deleteriously affected. A multitude of different dispersants have been investigated thus far, but of particular interest is deoxyribonucleic acid (DNA), which has previously been demonstrated to effectively separate metallic and semiconducting carbon nanotubes. Here, we investigate the ability of synthetic nucleobase‐containing poly(acrylamide) polymers to produce stable nanotube dispersions in organic solvents. Polymers bearing different nucleobase and backbone structures, as well as block copolymers with different block sequences were investigated. Polymer:SWNT mass ratios and solvent compositions were optimized for the nucleobase‐functionalized polymers, and semiconducting and metallic SWNT populations were identified by a combination of UV‐Vis‐NIR absorption, Raman, and fluorescence spectroscopy. These results demonstrate the capacity for synthetic DNA analogues to disperse SWNTs in organic media. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2611–2617     

Separation of single‐walled carbon nanotubes with aromatic group functionalized polymethacrylates and building blocks contribution to the enrichment

We previously showed that in N,N‐dimethylformamide (DMF), poly(9‐anthracenylmethyl methacrylate) (PAMMA) and poly(2‐naphthylmethacrylate) selectively disperse semiconducting and metallic single‐walled carbon nanotubes (SWNTs), respectively. We have also proposed a new noncovalent polymer interaction based on photon induced dipole–dipole interaction to account for the metallicity‐based selectivity. In this article, we investigate two other polymethacrylates, that is, poly(benzyl methacrylate) (PBMA) and poly(methylmethacrylate)‐co‐(9‐anthracenylmethyl acrylate) (PMMA‐c‐PAMA) in the light of our previously proposed photon‐induced dipole–dipole interaction. We find that PBMA and PMM‐c‐PAMMA in DMF show no metallicity selectivity. The different selective behavior of the four polymers in DMF manifests the decisive influence of the side aromatic group in determining their metallicity selectivity. The nonpreferential energy transfer from PMMA‐c‐PAMA to SWNTs and the nonoverlap of PBMA fluorescence (in the ultraviolet range) with nanotube absorption account for their nonselectivity of specific nanotube species. Further, the parallel relationship between the diameters of extracted tube species and the affinity between polymers and solvents suggests the leading role of the polymeric conformation on the diameter selectivity. A sufficient (i.e., 2 weeks) standing time of the SWNTs solution after sonication, during which the polymers presumably optimize their conformation to the SWNTs, was found to be essential to the enrichment. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

H‐shaped (ABCDE type) quintopolymer via click reaction [3 + 2] strategy

H‐shaped quintopolymer containing different five blocks: poly(ε‐caprolactone) (PCL), polystyrene (PS), poly(ethylene glycol) (PEG), and poly(methyl methacrylate) (PMMA) as side chains and poly(tert‐butyl acrylate) (PtBA) as a main chain was simply prepared from a click reaction between azide end‐functionalized PCL‐PS‐PtBA 3‐miktoarm star terpolymer and PEG–PMMA‐block copolymer with alkyne at the junction point, using Cu(I)/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as a catalyst in DMF at room temperature for 20 h. The H‐shaped quintopolymer was obtained with a number–average molecular weight (M_n) around 32,000 and low polydispersity index (M_w/M_n) 1.20 as determined by GPC analysis in THF using PS standards. The click reaction efficiency was calculated to have 60% from ¹H NMR spectroscopy. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4459–4468, 2008     

The effect of molecular weight on the separation of semiconducting single‐walled carbon nanotubes using poly(2,7‐carbazole)s

The use of selective interactions between conjugated polymers and single‐walled carbon nanotubes has emerged as a promising method for the separation of nanotubes by electronic type. Although much attention has been devoted to investigating polyfluorenes and their ability to disperse semiconducting carbon nanotubes under specific conditions, other polymer families, such as poly(2,7‐carbazole)s, have been relatively overlooked. Poly(2,7‐carbazole)s have been shown to also preferentially interact with semiconducting carbon nanotubes, however a detailed investigation of polymer parameters, such as molecular weight, has not been performed. We have prepared seven different molecular weights of a poly(2,7‐carbazole), from short chain oligomers to high molecular weight polymers, and have investigated their effectiveness at dispersing semiconducting single‐walled carbon nanotubes. Although all polymer chain lengths were able to efficiently exfoliate carbon nanotube bundles using a mild dispersion protocol, only polymers above a certain threshold molecular weight (M_n ～ 27 kDa) were found to exhibit complete selectivity for semiconducting nanotubes, with no observable signals from metallic species. Additionally, we found the quality of separation to be strongly dependent on the ratio of polymer to carbon nanotube. Contrary to previous reports, we have found that an excess of poly(2,7‐carbazole) leads to incomplete removal of metallic carbon nanotubes. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2510–2516     

Surface and interface morphology of polystyrene/poly(methyl methacrylate) thin‐film blends and bilayers

The surface and interface morphologies of polystyrene (PS)/poly(methyl methacrylate) (PMMA) thin‐film blends and bilayers were investigated by means of atomic force microscopy (AFM) and X‐ray photoelectron spectroscopy. Spin‐coating a drop of a PS solution directly onto a PMMA bottom layer from a common solvent for both polymers yielded lateral domains that exhibited a well‐defined topographical structure. Two common solvents were used in this study. The structure of the films changed progressively as the concentration of the PS solution was varied. The formation of the blend morphology could be explained by the difference in the solubility of the two polymers in the solvent and the dewetting of PS‐rich domains from the PMMA‐rich phase. Films of the PS/PMMA blend and bilayer were annealed at temperatures above their glass‐transition temperatures for up to 70 h. All samples investigated with AFM were covered with PS droplets of various size distributions. Moreover, we investigated the evolution of the annealed PS/PMMA thin‐film blend and bilayer and gave a proper explanation for the formation of a relatively complicated interface inside a larger PS droplet. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 9–21, 2006     

Facile postpolymerization end‐modification of RAFT polymers

One‐pot methods for the end‐group postpolymerization modification of reversible addition fragmentation chain transfer (RAFT) derived polymers were investigated. Dithioester‐terminated polymers were transformed into ω‐functionalized polymers through conjugate addition of a variety of acrylates with an intermediate thiol. These methods provide a versatile means of introducing a variety of functionalities onto the polymer terminus, while simultaneously removing the residual dithiobenzoate group. A series of functionalized polymethylmethacrylate‐b‐polystyrene (PMMA‐b‐PS) polymers were synthesized utilizing the developed methods to probe the effect of charged end groups on diblock copolymer phase separation in thin films. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 346–356, 2009     

Grafting of aldehyde structures to single‐walled carbon nanotubes for application in phenolic resin‐based composites

Grafting of aldehyde structures to single‐walled carbon nanotubes (SWNTs) has been carried out to endow the nanotubes with appropriate wettability. The results of Fourier transform infrared (FTIR) spectroscopy, ultraviolin‐visible‐near infrared (UV‐VIS‐NIR) spectroscopy, and Raman spectroscopy provide the supporting evidence of aldehyde structures covalently attached to SWNTs. The improved wettability of aldehyde‐functionalized SWNTs (f‐SWNTs) was demonstrated by their good dispersion in organic medium, namely, ethanol and phenolic resin. The prospective covalent bonding between aldehyde structures on the surfaces of f‐SWNTs and phenolic resin makes it possible to prepare an integrated composite with the enhanced‐interfacial adhesion. The f‐SWNT composites, therefore, show much higher average values of dσ/dW_CNT and dE/dW_CNT (i.e., tensile strength and Young's modulus per unit weight fraction) compared with the composites filled with pristine SWNTs or MWNTs. The respective maxima are 9680 MPa and 320 GPa. It is thus feasible for f‐SWNTs to prepare the moderately enhanced but lightweight phenolic composites. Furthermore, the incorporation of f‐SWNTs does not limit the application of phenolic resin as insulation material. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6135–6144, 2009     

Anionic synthesis and detection of fluorescence‐labeled polymers with a terminal anhydride group

To monitor polymer–polymer coupling reactions between two different monofunctional polymers in dilute polymer blends, fluorescence‐labeled anhydride‐functional polystyrene (PS) and poly(methyl methacrylate) (PMMA) were prepared by conventional anionic polymerization. Sequential trapping of lithiopolystyrene by 1‐(2‐anthryl)‐1‐phenylethylene (APE) and then di‐t‐butyl maleate (4) provided, after pyrolysis, anhydride‐functional fluorescent PS. Fluorescent PMMA anhydride (8) was synthesized with sec‐butyllithium/APE as an initiator for the anionic polymerization of methyl methacrylate, trapping by 4, and pyrolysis. These polymers could be reacted with amine‐functional polymers by melt blending, and the reaction progress could be monitored by gel permeation chromatography coupled with fluorescence detection. This technique not only allows monitoring of the coupling reaction with high sensitivity (ca. 100 times more sensitive than refractive index detection) but also permits selective detection because unlabeled polymers are invisible to fluorescence detection. This highly sensitive and selective detection methodology was also used to monitor the coupling reaction of 8 with PS‐NH₂ at a thin‐film interface, which was otherwise difficult to detect by conventional methods. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2177–2185, 2000     

Synthesis of well‐defined and end‐polymerizable star‐shaped polysulfides and their application to negative photoresist

Various star‐shaped poly(phenoxy propylene sulfide)s (PPSs) bearing curable end groups were synthesized by the functionalization of the propagating ends of star‐shaped poly(PPS) with various electrophilies. The functionalization with chloromethyl styrene proceeded quantitatively, and afforded polymers with M_n almost agreed with theoretical value and narrow M_w/M_n. The photocuring conditions were optimized, and the addition of 10 wt % of poly(ethylene glycol) diacrylate was effective to attain sufficient crosslinking. The photocuring reaction of the end‐functionalized poly(PPS) films cast on silicon wafers was conducted by UV irradiation. The cured poly (PPS)s became insoluble in THF, supporting the sufficient crosslinking. Developing of a cured polymer yielded a negative photoresist pattern. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Correlation of architecture with excimer emission in 100% pyrene‐labeled self‐assembled polymers

Pyrene was incorporated as pendant unit to side‐chain urethane methacrylate polymers having a short ethyleneoxy or a long polyethyleneoxy spacer segment. The short‐spacer pyrene urethane methacrylate was also incorporated either as block or random copolymer (1:9) along with polystyrene. The excimer emission was observed to be different for different polymers with the random copolymer exhibiting the lowest efficiency. But, the total quantum yield was highest (? = 0.58) for random copolymer due to the high emission coefficient of monomer compared to that of excimer. The polymer dynamics were compared by steady state emission and fluorescence decay in THF or THF/water (9:1) solvent mixture and films. The solid state decay profile showed decay without a rise time indicating presence of ground state aggregates. In THF/water (9:1), the decay profile at the excimer emission (500 nm) showed a rise time indicating dynamic excimers. The evolution of excimeric emission centred ～430 or ～480 nm as a function of temperature was also studied in THF/water (9:1). The I_E/I_M ratio for the λ_{343 nm} excitation exhibited steady increase with temperature with the block copolymer PS‐b‐PIHP exhibiting the highest ratio and highest rate of increase; whereas, the random copolymer PS‐r‐PIHP had the lowest I_E/I_M ratios. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Multiarm star block copolymers via Diels‐Alder click reaction

Two types of multiarm star block copolymers: (polystyrene)_m‐poly(divinylbenzene)‐poly(methyl methacrylate)_n, (PS)_m‐polyDVB‐(PMMA)_n and (polystyrene)_m‐poly(divinylbenzene)‐poly(tert‐butyl acrylate)_k, (PS)_m‐polyDVB‐(PtBA)_k were successfully prepared via a combination of cross‐linking and Diels–Alder click reactions based on “arm‐first” methodology. For this purpose, multiarm star polymer with anthracene functionality as reactive periphery groups was prepared by a cross‐linking reaction of divinyl benzene using α‐anthracene end functionalized polystyrene (PS‐Anth) as a macroinitiator. Thus, obtained multiarm star polymer was then reacted with furan protected maleimide‐end functionalized polymers: PMMA‐MI or PtBA‐MI at reflux temperature of toluene for 48 h resulting in the corresponding multiarm star block copolymers via Diels–Alder click reaction. The multiarm star and multiarm star block copolymers were characterized by using ¹H NMR, SEC, Viscotek triple detection SEC (TD‐SEC) and UV. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 178–187, 2009     

Synthesis of highly dispersed,block copolymer‐grafted TiO2 nanoparticles within neat block copolymer films

The objective of the study is to formulate exclusive block copolymer (BCP) nanocomposites by dispersing bcp end‐grafted nanoparticles (bcp‐g‐nps) of PMMA‐b‐PS‐g‐TiO₂ within PS‐b‐PMMA matrix. PMMA‐b‐PS‐g‐TiO₂ is synthesized using a “grafting‐to” approach and characterized by XPS and TGA to establish that the copolymer chains were bonded to NPs. Good dispersion of bcp‐g‐nps in PMMA and PS‐PMMA bcp films is observed, in contrast to poor dispersion in PS films. In PS‐PMMA films, the compatible and identical bcp nature of the end‐grafted polymer, and large NP size caused it to span across entire PS‐PMMA domains. Poor and good dispersion in PS and PMMA matrices, respectively, can be rationalized by the fact that NPs interactions are driven by the PMMA at the outer corona of the bcp‐g‐nps. Developing bcp‐g‐nps as a strategic route to preparation of highly dispersed high permittivity NPs like titanium dioxide (TiO₂) in bcp matrix can have important ramifications for energy storage devices. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 468–478     

Titanium‐mediated [CpTiCl2(OEt)] ring‐opening polymerization of lactides: A novel route to well‐defined polylactide‐based complex macromolecular architectures

Among three cyclopentadienyl titanium complexes studied, CpTiCl₂(OEt), containing a 5% excess CpTiCl₃, has proven to be a very efficient catalyst for the ring‐opening polymerization (ROP) of L ‐lactide (LLA) in toluene at 130 °C. Kinetic studies revealed that the polymerization yield (up to 100%) and the molecular weight increase linearly with time, leading to well‐defined PLLA with narrow molecular weight distributions (M_w/M_n ≤ 1.1). Based on the above results, PS‐b‐PLLA, PI‐b‐PLLA, PEO‐b‐PLLA block copolymers, and a PS‐b‐PI‐b‐PLLA triblock terpolymer were synthesized. The synthetic strategy involved: (a) the preparation of OH‐end‐functionalized homopolymers or diblock copolymers by anionic polymerization, (b) the reaction of the OH‐functionalized polymers with CpTiCl₃ to give the corresponding Ti‐macrocatalyst, and (c) the ROP of LLA to afford the final block copolymers. PMMA‐g‐PLLA [PMMA: poly(methyl methacrylate)] was also synthesized by: (a) the reaction of CpTiCl₃ with 2‐hydroxy ethyl methacrylate, HEMA, to give the Ti‐HEMA‐catalyst, (b) the ROP of LLA to afford a PLLA methacrylic‐macromonomer, and (c) the copolymerization (conventional and ATRP) of the macromonomer with MMA to afford the final graft copolymer. Intermediate and final products were characterized by NMR spectroscopy and size exclusion chromatography, equipped with refractive index and two‐angle laser light scattering detectors. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1092–1103, 2010     

The effect of length of single‐walled carbon nanotubes (SWNTs) on electrical properties of conducting polymer–SWNT composites

DC conductivity of conjugated polymer‐single‐walled carbon nanotube (SWNT) composite films has been measured for different SWNT concentrations. The composite was prepared by dispersing SWNTs in the poly (3‐octylthiophene), P3OT matrix already dissolved in xylene. The conductivity of the composite films showed a rapid increase as the SWNT concentration increases beyond a certain value. This behavior is explained in terms of percolating paths provided by the SWNTs in the volume of polymer matrix. To investigate the effect of length of nanotubes on the percolation conductivity, different SWNT samples were employed with similar diameter but varying tube lengths. It was found that the conductivity of the composite films is strongly dominated by the length of the nanotubes. Lower percolation limit and high conductivity value of composite films is observed for longer nanotubes. Furthermore, the conductivity is observed to be dependent on the size of the host polymer molecule also. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 89–95, 2010     

Synthesis of poly(ethylene‐co‐vinyl alcohol)‐g‐polystyrene graft copolymer and their applications for ordered porous film and compatibilizer

A series of new functional poly(ethylene‐co‐vinyl alcohol)‐g‐polystyrene graft copolymers (EVAL‐g‐PS) with controlled molecular weight (M_n = 38,000–94,000 g mol^?1) and molecular weight distribution (M_w/M_n = 2.31–3.49) were synthesized via a grafting from methodology. The molecular structure and component of EVAL‐g‐PS graft copolymers were confirmed by the analysis of their ¹H NMR spectra and GPC curves. The porous films of such copolymers were fabricated via a static breath‐figure (BF) process. The influencing factors on the morphology of such porous films, such as solvent, temperature, polymer concentration, and molecular weight of polymer were investigated. Ordered porous film and better regularity was fabricated through a static BF process using EVAL‐g‐PS solution in CHCl₃. Scanning electron microscopy observation reveals that the EVAL‐g‐PS graft copolymer is an efficient compatibilizer for the blend system of low‐density polyethylene/polystyrene. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 516–524     

Intimate blending of binary polymer systems from their common cyclodextrin inclusion compounds

A procedure for the formation of intimate blends of three binary polymer systems polycarbonate (PC)/poly(methyl methacrylate) (PMMA), PC/poly(vinyl acetate) (PVAc) and PMMA/PVAc is described. PC/PMMA, PC/PVAc, and PMMA/PVAc pairs were included in γ‐cyclodextrin (γ‐CD) channels and were then simultaneously coalesced from their common γ‐CD inclusion compounds (ICs) to obtain intimately mixed blends. The formation of ICs between polymer pairs and γ‐CD were confirmed by wide‐angle X‐ray diffraction (WAXD), fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC). It was observed [solution ¹H nuclear magnetic resonance (NMR)] that the ratios of polymers in coalesced PC/PMMA and PC/PVAc binary blends are significantly different than the starting ratios, and PC was found to be preferentially included in γ‐CD channels when compared with PMMA or PVAc. Physical mixtures of polymer pairs were also prepared by coprecipitation and solution casting methods for comparison. DSC, solid‐state ¹H NMR, thermogravimetric analysis (TGA), and direct insertion probe pyrolysis mass spectrometry (DIP‐MS) data indicated that the PC/PMMA, PC/PVAc, and PMMA/PVAc binary polymer blends were homogeneously mixed when they were coalesced from their ICs. A single, common glass transition temperature (T_g) recorded by DSC heating scans strongly suggested the presence of a homogeneous amorphous phase in the coalesced binary polymer blends, which is retained after thermal cycling to 270 °C. The physical mixture samples showed two distinct T_gs and ¹H T_1ρ values for the polymer components, which indicated phase‐separated blends with domain sizes above 5 nm, while the coalesced blends exhibited uniform ¹H spin‐lattice relaxation values, indicating intimate blending in the coalesced samples. The TGA results of coalesced and physical binary blends of PC/PMMA and PC/PVAc reveal that in the presence of PC, the thermal stability of both PMMA and PVAc increases. Yet, the presence of PMMA and PVAc decreases the thermal stability of PC itself. DIP‐MS observations suggested that the degradation mechanisms of the polymers changed in the coalesced blends, which was attributed to the presence of molecular interactions between the well‐mixed polymer components in the coalesced samples. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2578–2593, 2005     

Graft copolymers via ROMP and Diels–Alder click reaction strategy

Anthracene‐functionalized oxanorbornene monomer and oxanorbornenyl polystyrene (PS) with ω‐anthracene end‐functionalized macromonomer were first polymerized via ring‐opening metathesis polymerization using the first‐generation Grubbs' catalyst in dichloromethane at room temperature and then clicked with maleimide end‐functionalized polymers, poly(ethylene glycol) (PEG)‐MI, poly(methyl methacrylate) (PMMA)‐MI, and poly(tert‐butyl acrylate) (PtBA)‐MI in a Diels–Alder reaction in toluene at 120 °C to create corresponding graft copolymers, poly(oxanorbornene)‐g‐PEG, poly(oxanorbornene)‐g‐PMMA, and graft block copolymers, poly(oxanorbornene)‐g‐(PS‐b‐PEG), poly(oxanorbornene)‐g‐(PS‐b‐PMMA), and poly(oxanorbornene)‐g‐(PS‐b‐PtBA), respectively. Diels–Alder click reaction efficiency for graft copolymerization was monitored by UV–vis spectroscopy. The dn/dc values of graft copolymers and graft block copolymers were experimentally obtained using a triple detection gel permeation chromatography and subsequently introduced to the software so as to give molecular weights, intrinsic viscosity ([η]) and hydrodynamic radius (R_h) values. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Functionalized SWNT/polymer nanocomposites for dramatic property improvement

In this paper, we present results for polymer nanocomposites of poly‐ (methyl methacrylate) (PMMA) and amide‐functionalized SWNTs. The results demonstrate that even at very low loadings, 1 wt % (0.5 vol %), the mechanical and electrical properties are significantly improved. The improvement over PMMA properties exceeds the theoretical bounds for composites with the same volume fraction loading of randomly oriented, straight, individually dispersed nanotubes. The modeling and experimental results thus suggest that the nanotube bundles are well dispersed in the polymer matrix, that the functionalization significantly improves interaction with polymer, and that the interphase formed has improved mechanical properties over that of the matrix material. Loss modulus results indicate a significant difference between functionalized and nonfunctionalized tubes in the composite. Functionalized tubes result in a composite in which relaxation mechanisms are shifted by 30 °C from that of the matrix material, indicating extensive interphase regions and absence of PMMA with bulk properties. Unfunctionalized composites demonstrate a broadening of relaxation modes, but still retain the signature of bulk PMMA properties. These data suggest a morphological difference with a discrete interphase layer in unfunctionalized composites and a fully transformed matrix in the case of functionalization. This difference is consistent with electrical and mechanical property data. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2269–2279, 2005