Normalized mass mapping of Orbitrap data to define complex,polyglycerol‐based raw material compositions

Kendrick Mass Mapping of complex sample compositions, via data derived by Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) at 1 000 000 resolution, is becoming more common. The Orbitrap mass spectrometer (Fourier Transform Axially Harmonic Orbital Trapping) also uses FT methods and indirect detection, though operating at a maximum resolution of 100 000. We define the more general case of Normalized Mass Mapping to any repeating oligomer unit (e.g., C₃H₆O₂) and apply it to Orbitrap‐based mapping of a complex polyglycerol ester, 'green' raw material. Mass measurement errors showed sub‐ppm precision and accuracy in many cases, parameters that are critical to obtaining well‐defined maps. Map‐derived, raw‐material‐characterization parameters such as iodine value are compared with wet‐chemical results and show reasonable agreement for our purposes. The methodology appears applicable to raw material control and eliminates wet chemical methods. Copyright © 2010 John Wiley & Sons, Ltd.     

Artifacts Induced by Selective Blanking of Time-Domain Data in Fourier Transform Mass Spectrometry

Fourier transform mass spectrometry (FTMS) of the isolated isotopic distribution for a highly charged biomolecule produces time-domain signal containing large amplitude signal “beats” separated by extended periods of much lower signal magnitude. Signal-to-noise ratio for data sampled between beats is low because of destructive interference of the signals induced by members of the isotopic distribution. Selective blanking of the data between beats has been used to increase spectral signal-to-noise ratio. However, blanking also eliminates signal components and, thus, can potentially distort the resulting FT spectrum. Here, we simulate the time-domain signal from a truncated isotopic distribution for a single charge state of an antibody. Comparison of the FT spectra produced with or without blanking and with or without added noise clearly show that blanking does not improve mass accuracy and introduces spurious peaks at both ends of the isotopic distribution (thereby making it more difficult to identify posttranslational modifications and/or adducts). Although the artifacts are reduced by use of multiple Gaussian (rather than square wave) windowing, blanking appears to offer no advantages for identifying true peaks or for mass measurement.

ESI-FTICRMS与更换底物保护基团方法联用表征烯醇反应中间体

更换底物保护基团的化学方法与质谱、同位素标记以及核磁方法联用表征钯催化的烯醇环化反应中间体。实验表明更换底物的保护基团方法可以明显降低反应速度,延长关键中间体离子的存活寿命,不仅清晰地观察了反应的整个进程而且成功地捕获检测表征了其中关键中间体离子。进一步,串联质谱(SORI-CAD)方法研究了其中一些中间体离子的气相裂解反应行为,归纳总结其气相裂解反应的途径。结合同位素标记的结构为它们结构的确证提供了丰富信息。     

Evidence for electron‐based ion generation in radio‐frequency ionization

Radio‐frequency ionization (RFI) is a novel ionization method coupled to mass spectrometry (MS) for analysis of semi‐volatile and volatile organic compounds (VOCs). Despite the demonstrated capabilities of RFI MS for VOC analysis in both positive‐ and negative‐ion modes, mechanism of RFI is not completely understood. Improved understanding of the ion generation process in RFI should expand its utility in MS. Here, we studied the possibility of electron emission in RFI using both direct charged particle current measurements and indirect electron detection in a 9.4‐T Fourier transform‐ion cyclotron resonance (FT‐ICR) mass spectrometer. We show that RF‐generated electrons can be trapped in the ICR cell and, subsequently, reacted with neutral hexafluorobenzene (C₆F₆) molecules to generate C₆F₆^●?. Intensity of observed C₆F₆^●? species correlated with the number of trapped electrons and decreased as a function of electron quenching period. We also measured the electron attachment rate constant of hexafluorobenzene using a post‐RF electron trapping experiment. Measured electron attachment rate constant of hexafluorobenzene (1.19 (±0.53) × 10^?9 cm³ molecule^?1 s^?1) for post‐RF FT‐ICR MS agreed with the previously reported value (1.60 (±0.30) × 10^?9 cm³ molecule^?1 s^?1) from low‐pressure ICR MS measurements. Experimental results from direct and indirect electron measurements suggest that RFI process involves RF‐generated electrons under ultrahigh vacuum conditions. Copyright © 2015 John Wiley & Sons, Ltd.     

Fast Padé transform for optimal quantification of time signals from magnetic resonance spectroscopy

The fast Padé transform (FPT) is both a parametric and a nonparametric estimator that is capable of quantifying the input raw time signals without any fitting. The FPT simultaneously interpolates as well as extrapolates, and this is expected to mitigate truncation artifacts. To assess performance, it is necessary to compare the main features of the FPT with the characteristics of other parametric estimators, as well as with the fast Fourier transform (FFT), which can yield only shape spectra. The FPT can also give the shape of a spectrum, but accomplishes this in two totally different ways, with and without computing the spectral parameters (complex frequencies and amplitudes). A number of other parametric estimators used in signal processing are unable to yield shape spectra without prior extraction of the fundamental frequencies and the corresponding amplitudes. The primary goal of the present study is to assess the accuracy, robustness, and efficiency of the FPT for parametric and nonparametric estimations of experimentally measured time signals from in vivo magnetic resonance spectroscopy (MRS). Robustness and steadiness of the FPT are assessed relative to the FFT by monitoring the convergence rates of these two processors through a systematic and gradual decrease of the truncation level of the full signal length. Accuracy of the FPT is verified by performing error analysis of proven validity, using a gold standard, if available. Alternatively, comparison is made between the two complementary variants of the FPT that converge inside and outside the unit circle. Efficiency of the FPT is checked with respect to the FFT for estimation of the shape of a spectrum, as well as relative to other parametric processors, in the case of quantifications. To establish the accuracy, robustness, and efficiency of the FPT within the outlined multi‐level strategy, we use a time signal encoded via MRS at 4T from the brain of a healthy volunteer. We also assess the overall usefulness of the FPT for signal processing of data acquired from patients, in light of the emerging appreciation that spectroscopy of the tissue metabolites offers a number of vital advantages over the corresponding anatomical imaging in diagnostics. © 2005 Wiley Periodicals, Inc. Int J Quantum Chem, 2005     

Study of active naphtodianthrone St John's Wort compounds by electrospray ionization Fourier transform ion cyclotron resonance and multi‐stage mass spectrometry in sustained off‐resonance irradiation collision‐induced dissociation and infrared multiphoton dissociation modes

Five well‐known active naphtodianthrone constituents of Hypericum perforatum (St John's Wort) extracts have been investigated by electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI‐FTICRMS) and ESI‐FTICRMSⁿ. The studied compounds were hypericin, pseudohypericin, protohypericin, protopseudohypericin (biosynthetic precursors of the two former compounds, respectively) and isopseudohypericin (alkaline degradation product of pseudohypericin). Dissociation mass spectrometry measurements performed on the [M–H]^? ion presented a variable efficiency as a function of the used activation mode. Sustained off‐resonance irradiation collision‐induced dissociation (SORI–CID) only led to a restricted number of fragment ions. In contrast, IRMPD ensured the detection of numerous product ions. Ions detected in ESI‐FTICRMS and ESI‐FTICRMSⁿ experiments were measured with a very high mass accuracy (typically mass error is lower than 0.5 mDa at m/z close to 500) that allowed unambiguous formulae to be assigned to each signal observed in a mass spectrum. In spite of similar structures, specific fragmentation patterns were observed for the different compounds investigated. This study may be useful in the future to characterize in natural extracts these compounds (or derivatives of these compounds) by liquid chromatography/tandem mass spectrometry (LC/MS/MS) experiments by considering the MS/MS transitions highlighted in this paper. Copyright © 2009 John Wiley & Sons, Ltd.     

Glycerophospholipid profiling by high‐performance liquid chromatography/mass spectrometry using exact mass measurements and multi‐stage mass spectrometric fragmentation experiments in parallel

A profiling method for glycerophospholipids (GPs) in biological samples was developed using reversed‐phase high‐performance liquid chromatography (RP‐HPLC) coupled to hybrid linear ion trap‐Fourier transform ion cyclotron resonance mass spectrometry (LIT‐FTICRMS) with electrospray ionization (ESI) in the negative ionization mode. The method allowed qualitative (identification and structure elucidation) and relative quantitative determination of various classes of GPs including phosphatidylcholines, phosphatidylethanolamines, phosphatidylinositols, phosphatidylserines, phosphatidic acids, phosphatidylglycerols, and cardiolipins in a single experiment. Chromatographic separation was optimized by the examination of different buffer systems and special emphasis was paid on the detection by ESI‐MS. The hybrid LIT‐FTICRMS system was operated in the data‐dependent mode, switching automatically between FTICRMS survey scans and LIT‐MS/MS experiments. Thereby, exact masses for elemental composition determination and fragmentation data for identification and assignment of fatty acid residues are provided at the same time. The low absolute instrumental limits of detection (0.05 pmol for phosphatidylglycerol to 1 pmol for phosphatidic acid) complemented by a linear dynamic range of 1.5 to 2.5 orders of magnitude facilitated the relative quantification of GP species in a lipid extract from Saccharomyces cerevisiae. The developed method is a valuable tool for in‐depth GP profiling of biological systems. Copyright © 2009 John Wiley & Sons, Ltd.     

Characterization of complex assemblages of organic acids in geological samples by negative electrospray ionization mass spectrometry using a double‐focusing magnetic sector field mass spectrometer

Four different geological sample types (a crude oil, a crude oil asphaltene, a reservoir core extract and a reservoir core asphaltene) have been characterized by negative ionization electrospray mass spectrometry at low and high mass resolution using a double‐focusing magnetic sector field mass spectrometer. The mass range, shape of the spectra and the signal distribution of the acidic constituents as well as the average molecular weights, the total ion abundance and signal intensity in the spectra were compared for the different sample types. Nominal mass classes have been evaluated and Kendrick mass plots were generated in order to identify homologous series. For the crude oil sample, accurate mass assignments were made by high‐resolution double‐focusing magnetic sector field mass spectrometry (DFMSFMS) and were compared with those obtained by negative ion electrospray ionization (ESI) Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS). With both instrument types, compounds with the molecular composition C_nH_2n+zO₂, among which carboxylic acids predominated, were the main acidic compound class detectable in negative ESI mass spectra. Good agreement was achieved for the double bond class distribution and the carbon number distribution of the O₂ class. In addition, minor compound classes could be identified using FTICRMS. Copyright © 2010 John Wiley & Sons, Ltd.     

High-resolution analysis by nano-electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry for the identification of molecular species of phospholipids and their oxidized metabolites

Nano-electrospray ionization (ESI) Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) was applied to identify the molecular species of phosphatidylethanolamine of Caenorhabditis elegans, which has a high concentration of phospholipids with a fatty acyl chain having an odd number of carbon atoms. The molecular species of diacyl phosphatidylethanolamine with one fatty acyl chain having an odd number of carbon atoms and one fatty acyl chain having an even number of carbon atoms was identified separately from alkyl-acyl phosphatidylethanolamine with an alkyl chain having an even number of carbon atoms and a fatty acyl chain having an even number of carbon atoms. Furthermore, nano-ESI-FTICRMS was applied to the direct identification of oxidized phosphatidylcholine from soybean. The mass peaks of individual molecular species of oxidative phosphatidylcholine, such as 34:3 diacyl phosphatidylcholine with peroxide (+2O) (m/z 788.544) or 34:2 diacyl phosphatidylcholine with peroxide (+2O) (m/z 790.560), can be separated from the peaks of the molecular species of the non-oxidative phospholipids. This suggests that the mass peaks with a difference of less than 0.1 mass units in their molecular weight can be separated and that their individual exact molecular compositions can be obtained by the FTICRMS analysis. The high resolution and high accuracy of FTICRMS are very effective in the analysis of molecular species of phospholipids and their derivatives.     

Elucidating molecular level impact of peat fire on soil organic matter by laser desorption ionization Fourier transform ion cyclotron resonance mass spectrometry

Analytical and Bioanalytical Chemistry - In this work, laser desorption ionization coupled with Fourier transform ion cyclotron resonance mass spectrometry (LDI–FTICRMS) was used to...     

Analysis of cigarette smoke by laser desorption mass spectrometry

Laser desorption ionization Fourier transform ion cyclotron mass spectrometry (LDI–FTICRMS) has been successfully applied for the characterization of tobacco smokes. The versatily of analysis allows inorganic and organic tobacco smoke constituents to be identified. As a function of ion detection mode and laser irradiance experimental conditions, inorganic nitrate and sulfate as well as nicotine and associated nicotine, tobacco-specific nitrosamine, polycyclic aromatic hydrocarbon, polyoxygenated compounds are highlighted. The high mass resolution and the high mass accuracy attained by LDI–FTICRMS measurements allow the unambiguous assignment of detected species for m/z < 250 to be achieved.     

Molecular level comparison of water extractives of maple and oak with negative and positive ion ESI FT‐ICR mass spectrometry

Soluble extractives in wood function to protect living trees from destructive agents and also contribute to wood color and fragrance. Some extractive components have biological activities with medical applications. They also play important roles in wood processing and related applications. To increase the knowledge of wood chemistry, maple and oak were extracted by water. Ultraviolet/visible (UV/vis) spectroscopy indicated the presence of a phenolic compound, resorcinol, in maple extractives having higher molecular mass and more aromatic components than oak extractives. Negative and positive electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT‐ICR‐MS) identified thousands of formulas in the two samples in the m/z range of 200 to 800. They mainly fall into the lignin‐like, carbohydrate‐like, and tannin‐like compound categories. The top 25 peaks (ie, formulas) with the highest relative magnitude in negative ESI represented nearly 50% of the summed total spectral magnitude of all formulas assigned in the maple and oak extractives. Furthermore, the base peak (ie, most abundant peak) accounted for about 14% of the total abundance in each wood sample. Literature comparisons identified 17 of 20 formulas in the top five peaks of the four spectra as specific bioactive compounds in trees and other plants, implying the potential to explore utilization of maple and oak extractives for functional and medicinal applications. The various profiling of the top 25 peaks from the two samples also suggested the possible application of FT‐ICR‐MS for detecting chemical markers useful in profiling and identification of wood types and sources.     

2,5‐Dihydroxybenzoic acid solution in MALDI‐MS: ageing and use for mass calibration

2,5‐Dihydroxybenzoic acid (DHB) is one of the most widely used and studied matrix compounds in matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry. However, the influence of ageing of the DHB solution on the MALDI mass spectra has not been yet systematically studied. In this work, the possible changes occurring in the acidified acetonitrile/water solution of the MALDI matrix compound DHB during 1‐year usage period have been monitored with MALDI‐Fourier transform ion cyclotron resonance mass spectrometer (MALDI‐FT‐ICR‐MS) and attenuated total reflectance Fourier transform infrared (ATR‐FT‐IR) spectroscopy. No significant ageing products have been detected. The ability of the aged DHB solution to act as a MALDI matrix was tested with two materials widely used in art and conservation – bone glue (a proteinaceous material) and shellac resin (a resinous material) – and good results were obtained. A number of peaks in the mass spectra measured from the DHB solution were identified, which can be used for internal calibration of the mass axis. Copyright © 2014 John Wiley & Sons, Ltd.     

Identification and fragmentation pathways of caffeine metabolites in urine samples via liquid chromatography with positive electrospray ionization coupled to a hybrid quadrupole linear ion trap (LTQ) and Fourier transform ion cyclotron resonance mass spectrometry and tandem mass spectrometry

Liquid chromatography (LC) with positive ion electrospray ionization (ESI+) coupled to a hybrid quadrupole linear ion trap (LTQ) and Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) was employed for the simultaneous determination of caffeine and its metabolites in human urine within a single chromatographic run. LC/ESI‐FTICRMS led to the unambiguous determination of the molecular masses of the studied compounds without interference from other biomolecules. A systematic and comprehensive study of the mass spectral behaviour of caffeine and its fourteen metabolites by tandem mass spectrometry (MS/MS) was performed, through in‐source ion trap collision‐induced dissociation (CID) of the protonated molecules, [M+H]⁺. A retro‐Diels‐Alder (RDA) process along with ring‐contraction reactions were the major fragmentation pathways observed during CID. The base peak of xanthine precursors originates from the loss of methyl isocyanate (CH₃NCO, 57 Da) or isocyanic acid (HNCO, 43 Da), which in turn lose a CO unit. Also uric acid derivatives shared a RDA rearrangement as a common fragmentation process and a successive loss of CO₂ or CO. The uracil derivatives showed a loss of a ketene unit (CH₂CO, 42 Da) from the protonated molecule along with the loss of H₂O or CO. To assess the potential of the present method three established metabolite ratios to measure P450 CYP1A2, N‐acetyltransferase and xanthine oxidase activities were evaluated by a number of identified metabolites from healthy human urine samples after caffeine intake. Copyright © 2009 John Wiley & Sons, Ltd.     

Photochemical degradation of natural organic sulfur compounds (CHOS) from iron‐rich mine pit lake pore waters – an initial understanding from evaluation of single‐elemental formulae using ultra‐high‐resolution mass spectrometry

In order to better understand the chemical diversity of dissolved organic matter (DOM) in iron‐rich mine waters, a variety of sediment pore waters was analysed by means of ultra‐high‐resolution Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS). A considerable number of the DOM elemental formulae were found to contain sulfur. In a rather simplified experiment, DOM was exposed to sunlight in the presence of dissolved ferric iron, which is common in the oxygenated acidified epilimnetic waters of mine pit lakes. The photochemical alteration of the CHOS (carbon‐, hydrogen‐, oxygen‐ and sulfur‐containing) compounds was then categorised by following the changes in signal intensity of mass peaks. Nearly 20 000 elemental compositions were identified and sorted into the following categories: totally degraded, partially degraded, not significantly degraded, minor new photoproducts, and newly formed photoproducts. A large proportion of the CHOS compounds were found to be entirely degraded; the degradation ratios exceeded those of the CHO compounds. The pools of totally degraded compounds and those of newly formed products were contrasted with respect to photochemically relevant mass differences. These results indicate that photochemical loss of sulfur‐containing low molecular weight compounds can be considered likely. One feasible explanation is the photodegradation of sulfonic acids within the CHOS pool eventually leading to the release of sulfate. Copyright © 2010 John Wiley & Sons, Ltd.     

Fourier transform ion cyclotron resonance mass spectrometry using atmospheric pressure photoionization for high-resolution analyses of corticosteroids

Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) was coupled with atmospheric pressure photoionization (APPI) for the first time and used for the analysis of several corticosteroids.1 The analytes showed excellent response using APPI when compared with both electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI). APPI has the advantage of requiring less heat for desolvation, resulting in less thermal degradation of the analytes and higher signal-to-noise than APCI. In terms of ultimate sensitivity, APPI is more efficient than either ESI or APCI for the analysis of corticosteroids. With some compounds, the high-resolution capability of FTICRMS was necessary to obtain an accurate mass due to contributions of the M(+.) (13)C isotope in the [M+H](+) ion peak.     

Electron transfer dissociation in the hexapole collision cell of a hybrid quadrupole-hexapole Fourier transform ion cyclotron resonance mass spectrometer

Electron transfer dissociation (ETD) of proteins is demonstrated in a hybrid quadrupole-hexapole Fourier transform ion cyclotron resonance mass spectrometer (Qh-FTICRMS). Analyte ions are selected in the mass analyzing quadrupole, accumulated in the hexapole linear ion trap, reacted with fluoranthene reagent anions, and then analyzed via an FTICR mass analyzer. The hexapole trap allows for a broad fragment ion mass range and a high ion storage capacity. Using a 3 T FTICRMS, resolutions of 60 000 were achieved with mass accuracies averaging below 1.4 ppm. The high resolution, high mass accuracy ETD spectra provided by FTICR obviates the need for proton transfer reaction (PTR) charge state reduction of ETD product ions when analyzing proteins or large peptides. This is demonstrated with the ETD of ubiquitin and apomyoglobin yielding sequence coverages of 37 and 20%, respectively. We believe this represents the first reported successful combination of ETD and a FTICRMS.     

Use of the filter diagonalization method in the study of space charge related frequency modulation in Fourier transform ion cyclotron resonance mass spectrometry

The filter diagonalization method (FDM) is a recently developed computational technique capable of extracting resonance frequencies and amplitudes from very short transient signals. Although it requires stable resonance frequencies and is slower than the fast Fourier transform (FFT), FDM has a resolution and accuracy that is unmatched by the FFT or any other comparable techniques. This unique feature of FDM makes it an ideal tool for tracing space charge induced frequency modulations in Fourier transform ion cyclotron resonance (FT-ICR) cells, which are shown to reach +/-400 ppm even for such simple spectra as Substance P.     

Continuous‐flow sample introduction for field desorption/ionization mass spectrometry

We introduce continuous‐flow field desorption (FD) for improved spectral quality, higher sample throughput, and simpler interface to sample handlers and chromatographic equipment. A recently developed commercial FD probe with integral fused‐silica capillary allows sample dosing in situ, without probe removal and reinsertion. A stable FD‐generated ion current can be sustained for longer than an hour by continuous deposition of analyte solution on the FD emitter heated and at high voltage. Continuous‐flow FD allows ensemble averaging of up to 100 Fourier transform ion cyclotron resonance (FT‐ICR) mass spectra, in contrast to the traditional emitter dosing technique. Continuous‐flow FD is amenable to interface with liquid chromatography (LC) and/or automated sample injectors. Copyright © 2004 John Wiley & Sons, Ltd.     

Accurate mass measurement using Fourier transform ion cyclotron resonance mass spectrometry for structure elucidation of designer drug analogs of tadalafil, vardenafil and sildenafil in herbal and pharmaceutical matrices

Phosphodiesterase type 5 (PDE-5) inhibitors are a class of drugs used primarily in the treatment of erectile dysfunction. The Food and Drug Administration (FDA) approved PDE-5 inhibitors include sildenafil citrate, vardenafil hydrochloride and tadalafil. In this study, accurate mass measurements were made by electrospray ionization (ESI) using Fourier transform ion cyclotron resonance mass spectrometry (FTICRMS) to elucidate the structures of sildenafil, tadalafil and vardenafil analogs that were found in products marketed as dietary supplements. Initial detection of these analogs was accomplished through routine screening of suspect samples by liquid chromatography/electrospray ionization multi-stage mass spectrometry (LC/ESI-MS(n)) on a low-resolution ion trap instrument. The chromatographic behavior and mass spectrometric fragmentation patterns observed were often similar to those observed for FDA approved PDE-5 inhibitors. The mass accuracy and resolving power associated with FTICRMS allows for the determination of elemental compositions. Elucidation of the product ion structures for the analogs was accomplished through the use of accurate mass measurements with the aid of Mass Frontier software (version 4.0). Using FTICRMS, accurate masses with measurement errors averaging <0.4 ppm were achieved, allowing assignment of one possible elemental formula to each fragment ion. The mass measurement errors associated with [M + H](+) for the analogs aminotadalafil, piperidino vardenafil, hydroxyacetildenafil and piperidino acetildenafil were 0.1, 0.0, 0.1 and 0.5 ppm, respectively. Based on the accuracy of the measurements, structural assignments could be made with a high degree of confidence.