Determination of Lead and Cadmium in Sea‐ and Freshwater by Anodic Stripping Voltammetry with a Vibrating Bismuth Electrode

A solid, bismuth (Bi), disk, electrode is used to determine lead (Pb) in natural waters including seawater. The diffusion layer thickness was lowered from 93 to 29 µm by stirring, and to 18 µm by using the vibrated version of the Bi electrode. The Bi electrode does not require removal of dissolved oxygen, which facilitates in situ detection. The electrode was tested for the determination of Pb in coastal seawater samples. The detection limit for Pb was 0.15 nM in acetate buffer and 0.5 nM in seawater using a 2 min deposition time. Cadmium can be determined together with Pb but the sensitivity is about 10×lower. The Bi electrode compares unfavourably to a mercury electrode in terms of sensitivity.     

Study of Bare and Mercury‐Coated Vibrated Carbon,Gold and Silver Microwire Electrodes for the Determination of Lead and Cadmium in Seawater by Anodic Stripping Voltammetry

Carbon, gold and silver microwires are revisited under vibrated conditions for detection of trace lead and cadmium in seawater. The Pb and Cd peaks fully overlapped on the bare gold and carbon electrodes and partially on the silver electrode. The sensitivity of all three was insufficient for detection in uncontaminated waters. Peak separation was obtained after coating with mercury (Hg). Only the Hg‐coated silver electrode is suitable when preplated. Limits of detection for Pb using the Hg/C and Hg/Ag electrodes (20–40 pM), and Cd (70 pM), are sufficiently low for Pb and Cd detection in seawater.     

Electrochemical reduction of selenium on a silver electrode and its determination in river water

A new, simple, and fast method is described for determining selenium based on a silver wire electrode flow-through voltammetric detector. A comparison was done between the sensitivity of disk silver, mercury-modified glassy carbon, and mercury-modified gold electrodes. The response of the flow-through voltammetric detector was evaluated with respect to each electrode’s operating potential and pH in direct current mode. The limit of detection (3s) for Se(IV) was below 0.01 mg/L. The flow-through system does not need deposition times and the organic matter does not need to be removed before determining selenium in river water.     

An Arrayed Micro‐glutamate Sensor Probe Integrated with On‐probe Ag/AgCl Reference and Counter Electrodes

Complete all‐in‐one multi‐arrayed glutamate (Glut) sensors have been constructed on a silicon‐based micromachined probe composed of micro‐platinum (Pt) working electrodes, a micro‐silver/silver chloride (Ag/AgCl) reference electrode (RE), and a micro‐Pt counter electrode (CE). The OCP shift of the electrodeposited Ag/AgCl on‐probe micro‐reference electrode compared with a Ag/AgCl wire is <0.1 mV/h. The composition ratio of Ag, Cl, and Pt on the electrodeposited on‐probe micro‐reference electrode is observed to be 1.00 : 0.48 : 0.02 analyzed by EDS. The miniaturized amperometric Glut biosensors were constructed on working electrode sites (electrode area: ∼8.5×10⁻⁵ cm²) of the microprobe modified with glutamate oxidase (GlutOx) enzyme layers for the selective, fast, and continuous detection of L‐glutamate. The sensor selectivity towards common electroactive interferents has been improved significantly by coating the electrode surface with perm‐selective polymer layers, overoxidized polypyrrole (PPY) and Nafion®. The sensitivity, detection range, and response time of the proposed all‐in‐one Glut biosensors are 204.7±5.8 nA μM⁻¹ cm⁻² (N=5), 4.99–109 μM, and 2.7±0.3 sec, respectively and no interferent signals of AA and DA were observed. The sensor can be reused over 19 times of continuous repetitive operation (total measurement time: ∼4 hours) and the sensor sensitivity can retain up to four weeks of storage.     

Determination of lead and cadmium in seawater using a vibrating silver amalgam microwire electrode

Silver amalgamated electrodes are a good substrate to determine lead (Pb) and cadmium (Cd) in seawater because they have properties similar to mercury but without the free mercury (Hg). Here a silver amalgamated microwire (SAM) electrode is optimised for the determination of Pb and Cd in coastal waters and uncontaminated ocean waters. The SAM was vibrated during the deposition step to increase the sensitivity, and electroanalytical parameters were optimised. The Hg coating required plating from a relatively concentrated (millimolar) solution, much greater (500×) than used for instance to coat glassy carbon electrodes. However, the coating on the ex situ amalgamated electrode was found to be stable and could be used for up to a week to determine trace levels of Pb in seawater of natural pH. The limit of detection square-wave ASV (50 Hz) using the pre-plated SAM electrode was 8 pM Pb using a 1-min plating time at pH 4.5. The limit of detection in pH 2 seawater was 4 pM using a 5-min plating time, and it was 12 pM using a 10-min plating time at natural pH in the presence of air, using a square-wave frequency of 700 Hz. The vibrating SAM electrode was tested on the determination of Pb in reference seawater samples from the open Atlantic (at the 20 pM level), Pacific, and used for a study of Pb in samples collected over 24 h in Liverpool Bay (Irish Sea).     

Edge Plane Pyrolytic Graphite Electrodes for Stripping Voltammetry: a Comparison with Other Carbon Based Electrodes

The first examples of using edge plane pyrolytic graphite electrodes for anodic and cathodic stripping voltammetry (ASV and CSV) are presented, notably the ASV of silver and the CSV of manganese. In the former example, detection limits for silver (based on 3σ) of 8.1 nM and 0.185 nM for 120 s and 300 s accumulation time, respectively, were achievable using the edge plane electrode, which were superior to those observed on glassy carbon, basal plane pyrolytic graphite and boron‐doped diamond electrodes. In the second example, a detection limit for manganese of 0.3 μM was possible which was comparable with that achievable with a boron‐doped diamond electrode but with an increased sensitivity. Comparison of the edge plane pyrolytic graphite electrode with boron‐doped diamond electrodes reveals that the edge plane electrode has comparable detection limits and sensitivities whilst exhibiting a lower signal‐to‐noise ratio and large potential window for use in trace analysis suggesting boron‐doped diamond can be conveniently replaced by edge plane pyrolytic graphite as an electrode material in many applications.     

Electrochemical Behavior of Gold Nanoparticles Generated In Situ on 3‐(1‐Imidazolyl)propyl‐silsesquioxane

Gold nanoparticles of different morphologies have been synthesized on a silica‐based organic‐inorganic hybrid material for catalytic applications. The gold nanoparticles formations proceed through in situ chemical reduction of the AuCl₄^? anions previously adsorbed on 3‐(1‐imidazolyl)propyl‐silsesquioxane, which plays the role of substrate and stabilizer. Two distinct reducing agents, sodium citrate and sodium borohydride, were employed to generate gold nanoparticles of different sizes. UV‐vis diffuse reflectance as well as transmission electron microscopy were employed to evaluate the particle’s morphology. Modified carbon paste electrodes were prepared from these materials and their electrochemical behavior investigated using potassium ferrocyanide and 4‐nitrophenol as redox model compounds. Both AuNPs‐modified electrodes decreased the overpotential of 4‐nitrophenol reduction by around 90 mV compared to the unmodified electrode as evidenced by cyclic voltammetry experiment. However, the smaller diameter particles (borohydride‐reduced) produced more significant catalytic effect as a consequence of their large surface area. Regarding the sensing parameters, the sensitivity is higher for the borohydride‐reduced AuNPs while the values of limit of detection are of the same order of magnitude. Thus, the detection limit and sensitivity are 70.0±0.6 nM and 187 µA/mM for the citrate‐reduced AuNPs; and 75.0±2.2 nM and 238 µA/mM for the borohydride‐reduced AuNPs.     

Fabrication of Bismuth/Multi-walled Carbon Nanotube Composite Modified Glassy Carbon Electrode for Determination of Cobalt

A bismuth/multi‐walled carbon nanotube (Bi/MWNT) composite modified electrode for determination of cobalt by differential pulse adsorptive cathodic stripping voltammetry is described. The electrode is fabricated by potentiostatic pre‐plating bismuth film on an MWNT modified glassy carbon (GC) electrode. The Bi/MWNT composite modified electrode exhibits enhanced sensitivity for cobalt detection as compared with the bare GC, MWNT modified and bismuth film electrodes. Numerous key experimental parameters have been examined for optimum analytical performance of the proposed electrode. With an adsorptive accumulation of the Co(II)‐dimethylglyoxime complex at ?0.8 V for 200 s, the reduction peak current is proportional to the concentration of cobalt in the range of 4.0×10^?10?1.0×10^?7 mol/L with a lower detection limit of 8.1×10^?11 mol/L. The proposed method has been applied successfully to cobalt determination in seawater and lake water samples.     

Use of epoxy-embedded electrodes to integrate electrochemical detection with microchip-based analysis systems

A new method of fabricating electrodes for microchip devices that involves the use of Teflon molds and a commercially available epoxy to embed electrodes of various sizes and compositions is described. The resulting epoxy base can be polished to generate a fresh electrode and sealed against poly(dimethylsiloxane) (PDMS)-based fluidic structures. Microchip-based flow injection analysis was used to characterize the epoxy-embedded electrodes. It was shown that gold electrodes can be amalgamated with liquid mercury and the resulting mercury/gold electrode is used to selectively detect glutathione from lysed red blood cells. The ability to encapsulate multiple electrode materials of differing compositions enabled the integration of microchip electrophoresis with electrochemical detection. Finally, a unique feature of this approach is that the electrode connection is made from the bottom of the epoxy base. This enables the creation of three-dimensional gold pillar electrodes (65?μm in diameter and 27?μm in height) that can be integrated within a fluidic network. As compared with the use of a flat electrode of a similar diameter, the use of the pillar electrode led to improvements in both the sensitivity (72.1 pA/μM for the pillar versus 4.2 pA/μM for the flat electrode) and limit of detection (20 nM for the pillar versus 600 nM for the flat electrode), with catechol being the test analyte. These epoxy-embedded electrodes hold promise for the creation of inexpensive microfluidic devices that can be used to electrochemically detect biologically important analytes in a manner where the electrodes can be polished and a fresh electrode surface is generated as desired.     

Microband Sensor for As(III) Analysis: Reduced Matrix Interference

A portable sensor based on a microband design for arsenic detection in drinking water is presented. The work was focused to minimize interference encountered with a standard screen‐printed electrodes featuring an onboard gold working electrode, carbon counter and silver−silver chloride pseudo‐reference electrodes as composite coatings on plastic surface. The interference effect was identified as chloride ions interacting with the silver surface of the reference electrode and formation of soluble silver chloride complexes such as AgCl₄³⁻. By modification of the reference electrodes with Nafion membrane (5 % in alcohols), the interference was entirely eliminated. However, membrane coverage and uniformity can impact the electrodes reproducibility and performance. Hence, the sensor design was further considered and a microband format was produced lending favorable diffusive to capacitive current characteristics. Using the microband electrodes allowed As(III) detection with limit of detection of 0.8 ppb (in 4 M HCl electrolyte), inherently avoiding the problems of electrode fouling and maximizing analyte signal in river water samples. This is below the World Health Organization limit of 10 μg L⁻¹ (ppb). The electrolyte system was chosen so as to avoid problems from other common metal ions, most notably Cu(II). The presented electrode system is cost effective and offers a viable alternative to the colorimetric test kits presently employed for arsenic analysis in drinking water.     

Disposable Electrodes for Capacitive Immunosensor

Disposable electrodes were fabricated by coating chromium (5 nm) and gold (200 nm) on glass strips (5.0 mm×25.4 mm) and used in a label‐free immunosensor. Human serum albumin (HSA) and its antigen (anti‐HSA) were used as a model system. Electropolymerization of o‐phenylenediamine was used for the immobilization of anti‐HSA by covalent binding. A linear relationship was obtained in the range from 1.0×10^?14 to 1.0×10^?9 M with a limit of detection of 8.0×10^?15 M. Each modified electrode can be reused up to 30 times. The developed system was applied for human serum samples and compared to Albumin BCG method.     

Pulsed Amperometric Detection of Histamine at Glassy Carbon Electrodes Modified with Gold Nanoparticles

Gold nanocrystal‐modified glassy carbon electrodes (nAu‐GCE) were prepared and used for the determination of histamine by flow injection and high performance liquid chromatography using pulsed amperometric detection (PAD) as the detection mode. Experimental variables involved in the electrodeposition process of gold from a HAuCl₄ solution were optimized. A catalytic enhancement of the histamine voltammetric response was observed at the nAu‐GCE when compared with that obtained at a conventional Au disk electrode, as a consequence of the microdispersion of gold nanocrystals on the GC substrate. The morphological and electrochemical characteristics of the nAu‐GCE were evaluated by SEM and cyclic voltammetry. PAD using a very simple potential waveform consisting of an anodic potential (+700 mV for 500 ms) and a cathodic potential (?300 mV for 30 ms), was used to avoid the electrode surface fouling when histamine was detected under flowing conditions. Flow injection amperometric responses showed much higher I_p values and signal‐to‐noise ratios at the nAu‐GCE than at a conventional gold disk electrode. A limit of detection of 6×10^?7 mol L^?1 histamine was obtained. HPLC‐PAD at the nAu‐GCE was used for the determination of histamine in the presence of other biogenic amines and indole. Histamine was determined in sardine samples spiked at a 50 μg g^?1 concentration level, with good results. Furthermore, the chromatographic PAD method was also used for monitoring the formation of histamine during the decomposition process of sardine samples.     

Trace Analysis of Heavy Metals (Cd,Pb, Hg) Using Native and Modified 3D Printed Graphene/Poly(Lactic Acid) Composite Electrodes

Here we investigate the use of 3D printed graphene/poly(lactic acid) (PLA) electrodes for quantifying trace amounts of Hg, Pb, and Cd. We prepared cylindrical electrodes by sealing a 600 μm diameter graphene/PLA filament in a pipette tip filled with epoxy. We characterized the electrodes using scanning electron microscopy, Raman spectroscopy, and cyclic voltammetry in ferrocene methanol. The physical characterization showed a significant amount of disorder in the carbon structure and the electrochemical characterization showed quasi‐reversible behavior without any electrode pretreatment. We then used unmodified graphene/PLA electrode to quantify Hg, and Pb and Cd in 0.01 M HCl and 0.1 M acetate buffer using square wave anodic stripping voltammetry. We were able to quantify Hg with a limit of detection (LOD) of 6.1 nM (1.2 ppb), but Pb and Cd did not present measurable peaks at concentrations below ～400 nM. We improved the LODs for Pb and Cd by depositing Bi microparticles on the graphene/PLA and, after optimization, achieved clear stripping peaks at the 20 nM level for both ions (4.1 and 2.2 ppb for Pb²⁺ and Cd²⁺, respectively). The results obtained for all three metals allowed quantification below the US Environmental Protection Agency action limits in drinking water.     

Carbon Paste Electrode Modified with Functionalized Nanoporous Silica Gel as a New Sensor for Determination of Silver Ion

A new dipyridyl‐functionalized silica gel (DPSG) was synthesized. The potentiometric response of silver ion was investigated at a carbon paste electrode chemically modified with functionalized nanoporous silica gel. The electrodes with a DPSG proportions of 10.1% (w/w), showed very stable potential. Calibration plots with Nernstian slopes for Ag⁺ were observed, 58.7 (±0.9) mV decade^?1, over a wide linear range of concentration (5.0×10^?7 to 1.0×10^?1 M). The electrode has a detection limit of 1.0×10^?7 M. The selectivity coefficients measured by the match potential method in acetate buffer, pH 5.5, were investigated. The electrode has fast response time, high performance, high sensitivity in wide cation activity ranges, and good long term stability (more than 6 months). The method was satisfactory and used to determine the concentration of silver ion in waste waters contaminated by this metal.     

Disposable Gold Electrodes with Reproducible Area Using Recordable CDs and Toner Masks

The fabrication and characterization of very cheap disposable gold disk electrodes with reproducible area is reported. The innovation of the proposed procedure is the use of toner masks to define reproducible areas on uniform gold surfaces obtained from recordable compact disks (CD‐R). Toner masks are drawn in a laser printer and heat transferred to gold surfaces, defining exactly the electrodes area. The electrochemical behavior of these disposable electrodes was investigated by cyclic voltammetry in Fe(CN)₆^4? solutions. The relative standard deviation for signals obtained from 10 different gold electrodes was below 1 %. The size of the disk electrodes can be easily controlled, as attested by voltammetric responses recorded by using electrodes with radii varying from 0.5 to 3.0 mm. The advantages of using this kind of electrode for analytical measurements of substances that strongly adsorb on the electrode surface such as cysteine are also addressed.     

Mercury Detection in Seawater Using a Mercaptoacetic Acid Modified Gold Microwire Electrode

It is demonstrated here that it is possible to determine mercury in chloride containing media like seawater by anodic stripping voltammetry using a modified electrode. A gold microwire electrode is modified using mercaptoacetic acid (MAA) to eliminate the problem of calomel formation, allowing the mercury to become fully removed from the electrode surface after each scan. In a synthetic salt solution of KNO₃ the sensitivity for mercury was found to be improved by the surface modification. In seawater the sensitivity was not significantly improved possibly because of complexation of the mercury by the abundant chloride; however, the MAA coating prevented the formation of calomel causing the background scan to be free of mercury. Measurements in seawater at various pH values demonstrated that mercury detection is possible at natural pH (around 8); however, best sensitivity was attained at pH 4.8 with a deposition time of 3 min. A peak for copper occurred at more negative potential but did not interfere at this pH. The calibration was linear between 0 and 37 nM mercury with a limit of detection of 1 nM mercury.     

Comparison of DNA Hybridization at Rotating and Heated Gold Disk Electrodes

This paper reports about the influence of temperature, hybridization time and convection upon the detection of osmium tetroxide bipyridine‐labeled target oligonucleotides at rotating gold disk (RDE) and heated low temperature co‐fired ceramics (LTCC) gold disk electrodes. We used mixed self‐assembled monolayers of hexathiol‐linked probe oligonucleotides and mercaptohexanol on the gold surface of the electrodes for the hybridization detection of the labeled targets by means of square‐wave voltammetry. Due to protective strands, the osmium tetroxide‐modified target strands were still able to hybridize with the immobilized probe strands. The hybridization of such osmium tetroxide bipyridine‐modified target strands with thiol‐linked probe strands immobilized on gold yielded large reversible square‐wave‐voltammetric signals. Rotation speed and, hence, mass transport due to convection has only marginal effects. On the other hand, temperature affects greatly the hybridization step as indicated by both heated LTCC electrode in cold and RDE in warm hybridization solution. Calculated detection limits of 3.6 and 3.1 nM targets at the RDE and the LTCC electrode, respectively, have been almost the same at both types of electrodes. Applying an appropriate temperature during hybridization is more important than mechanically enhanced mass transport.     

Selective Detection of Dopamine Using Glassy Carbon Electrode Modified by a Combined Electropolymerized Permselective Film of Polytyramine and Polypyrrole‐1‐propionic Acid

A sensitive and selective electrochemical method for the determination of dopamine using a combined electropolymerized permselective film of polytyramine and polypyrrole‐1‐propionic acid on a glassy carbon (GC) electrode was developed. The formation of a “layer‐by‐layer” film has allowed for selective detection of dopamine in the presence of 3,4‐dihydroxyphenylalanine (L‐DOPA), DOPAC, ascorbic acid, uric acid, epinephrine and norepinephrine. The modified electrodes exhibited a detection limit of 100 nM with linearity ranging from 5×10^?6 to 5×10^?5 M. No cleaning step was required during the course of repeated measurement.     

Enhanced Sensitivity of 4‐Chlorophenol Detection by Use of Nitrobenzene as a Liquid Membrane over a Carbon Nanotube‐Modified Glassy Carbon Electrode

The analytical utility of nitrobenzene as a liquid membrane for the detection of hydrophobic compounds was examined with a glassy carbon electrode, using 4‐chlorophenol as the model analyte. Electrochemical experiments indicated a large partition coefficient for the entry of 4‐chlorophenol into the nitrobenzene (7.6×10²±1.5×10²). This was combined with an increase in effective electrode area by coating with single‐walled nanotubes. Differential pulse voltammetry produced a linear response across the range 0.3 nM to 1.5 nM with a sensitivity of 1.1×10^?5 A nM^?1 cm^?2. To the best of our knowledge, this limit of detection for phenol is lower than other nonenzymatic modifications of carbon.     

Catalytic Effect on Silver Electrodeposition of Gold Deposited on Carbon Electrodes

A new methodology, based on silver electrocatalytic deposition and designed to quantify gold deposited onto carbon paste electrode (CPE) and glassy carbon electrode (GCE), has been developed in this work. Silver (prepared in 1.0 M NH₃) electrodeposition at ?0.13 V occurs only when gold is previously deposited at an adequate potential on the electrode surface for a fixed period of time. When a CPE is used as working electrode, an adequate oxidation of gold is necessary. This oxidation is carried out in both 0.1 M NaOH and 0.1 M H₂SO₄ at oxidation potentials. When a GCE is used as working electrode, the oxidation steps are not necessary. Moreover, a cleaning step in KCN, which removes gold from electrode surface, is included. To obtain reproducibility in the analytical signal, the surface of the electrodes must be suitably pretreated; this electrodic pretreatment depends on the kind of electrode used as working electrode. Low detection limits (5.0×10^?10 M) for short gold deposition times (10 min for CPE and 5 min for GCE) were achieved with this novel methodology. Finally, sodium aurothiomalate can be quantified using silver electrocatalytic deposition and GCE as working electrode. Good linear relationship between silver anodic stripping peak and aurothiomalate concentration was found from 5.0×10^?10 M to 1.0×10^?8 M.