Soot particles in piston-top pool fires and exhaust at 5 and 15 MPa injection pressure in a gasoline direct-injection engine

This study shows the structure of soot particles sampled directly from wall wetting-induced pool fires formed on the piston top in a spark-ignition direct-injection (SIDI) engine. Of particular interest is its variation with injection pressure considering the current trend of high-pressure DI system development to reduce engine-out particulate emissions. Thermophoretic particle sampling was performed for transmission electron microscope (TEM) imaging, which was post-processed for statistical analysis of key morphology and internal structure parameters. These include the size distribution of soot aggregates and primary particles as well as carbon-layer fringe-to-fringe gap and concentricity. With the fixed engine speed and load conditions, in-flame soot particles are compared to the exhaust particles sampled simultaneously at selected 5 and 15 MPa injection pressures corresponding to low-speed/low-load and high-speed/high-load in practical engine operation. From the TEM images and statistical analysis, it was found that more concentrated and taller pool fire developed for 5-MPa injection leads to smaller soot aggregates composed of smaller soot primary particles due to suppressed soot growth in fuel-rich flames. However, the soot particles formed in 15-MPa injection-induced pool fires are at a more reactive status evidenced by less defined core-shell boundaries and higher fringe separation. The higher soot reactivity results in enhanced soot oxidation, which explains smaller soot aggregates and primary particles found for the 15-MPa injection in the exhaust sample.     

Influence of the cumulative effects of multiple laser pulses on laser-induced incandescence signals from soot

The effect of multiple laser pulses reaching soot particles before an actual laser-induced incandescence (LII) measurement is investigated in order to gain some insights on soot morphological and fine structure changes due to rapid laser heating. Soot, extracted from a premixed and a quenched diffusion flames, is flowing through a tubular cell and undergoes a variable number of pulses at different fluence. The response of soot is studied by the two-color LII technique. Transmission electron microscopy (TEM) analysis of laser-modified soot aggregates from the diffusion flame is also presented. The results indicate that even at low laser fluences a permanent soot transformation is induced causing an increase in the absorption function E(m). This is interpreted as an induced graphitization of soot particles by the laser pulse heating. At high fluences the vaporization process and a profound restructuring of soot particles affect the morphology of the aggregates. Soot from diffusion and premixed flames behaves in a similar way although this similarity occurs at different fluence levels indicating a different initial fine structure of soot particles.     

Laser-induced incandescence for soot-particle sizing at elevated pressure

This paper describes the applicability of laser-induced incandescence (LII) as a measurement technique for primary soot particle sizes at elevated pressure. A high-pressure burner was constructed that provides stable, laminar, sooting, premixed ethylene/air flames at 1–10 bar. An LII model was set up that includes different heat-conduction sub-models and used an accommodation coefficient of 0.25 for all pressures studied. Based on this model experimental time-resolved LII signals recorded at different positions in the flame were evaluated with respect to the mean particle diameter of a log-normal particle-size distribution. The resulting primary particle sizes were compared to results from TEM images of soot samples that were collected thermophoretically from the high-pressure flame. The LII results are in good agreement with the mean primary particle sizes of a log-normal particle-size distribution obtained from the TEM-data for all pressures, if the LII signals are evaluated with the heat-conduction model of Fuchs combined with an aggregate sub-model that describes the reduced heat conduction of aggregated primary soot particles. The model, called LIISim, is available online via a web interface. PACS 65.80.+n; 78.20.Nv; 42.62.-b; 47.70.Pq     

Transported JPDF modelling and measurements of soot at elevated pressures

Accurate measurements and modelling of soot formation in turbulent flames at elevated pressures form a crucial step towards design methods that can support the development of practical combustion devices. A mass and number density preserving sectional model is here combined with a transported joint-scalar probability density function (JDPF) method that enables a fully coupled scalar space of soot, gas-phase species and enthalpy. The approach is extended to the KAUST turbulent non-premixed ethylene-nitrogen flames at pressures from 1 to 5 bar via an updated global bimolecular (second order) nucleation step from acetylene to pyrene. The latter accounts for pressure-induced density effects with the rate fitted using comparisons with full detailed chemistry up to 20 bar pressure and with experimental data from a WSR/PFR configuration and laminar premixed flames. Soot surface growth is treated via a PAH analogy and soot oxidation is considered via O, OH and O₂ using a Hertz-Knudsen approach. The impact of differential diffusion between soot and gas-phase particles is included by a gradual decline of diffusivity among soot sections. Comparisons with normalised experimental OH-PLIF and PAH-PLIF signals suggest good predictions of the evolution of the flame structure. Good agreement was also found for predicted soot volume statistics at all pressures. The importance of differential diffusion between soot and gas-phase species intensifies with pressure with the impact on PSDs more evident for larger particles which tend to be transported towards the fuel rich centreline leading to reduced soot oxidation.     

Influence of soot particle aggregation on time-resolved laser-induced incandescence signals

Laser-induced incandescence (LII) is a versatile technique for quantitative soot measurements in flames and exhausts. When used for particle sizing, the time-resolved signals are analysed as these will show a decay rate dependent on the soot particle size. Such an analysis has traditionally been based on the assumption of isolated primary particles. However, soot particles in flames and exhausts are usually aggregated, which implies loss of surface area, less heat conduction and hence errors in estimated particle sizes. In this work we present an experimental investigation aiming to quantify this effect. A soot generator, based on a propane diffusion flame, was used to produce a stable soot stream and the soot was characterised by transmission electron microscopy (TEM), a scanning mobility particle sizer (SMPS) and an aerosol particle mass analyzer coupled in series after a differential mobility analyzer (DMA-APM). Despite nearly identical primary particle size distributions for three selected operating conditions, LII measurements resulted in signal decays with significant differences in decay rate. However, the three cases were found to have quite different levels of aggregation as shown both in TEM images and mobility size distributions, and the results agree qualitatively with the expected effect of diminished heat conduction from aggregated particles resulting in longer LII signal decays. In an attempt to explain the differences quantitatively, the LII signal dependence on aggregation was modelled using a heat and mass transfer model for LII given the primary particle and aggregate size distribution data as input. Quantitative agreement was not reached and reasons for this discrepancy are discussed.     

Investigation on the influence of soot size on prompt LII signals in flames

Theoretical papers predict that prompt LII signals are weakly dependent on the soot size due to the fact that larger particles reach higher temperatures during the heating process by nanosecond laser pulses. This question is of crucial importance for establishing LII as a practical technique for soot volume fraction measurements. In this work two-color prompt LII measurements have been performed in several locations of diffusion and rich premixed ethylene-air flames. The experimental apparatus was carefully designed with a probe volume of uniform light distribution and sharp edges, a 4 ns integration time around the signal pulse peak and narrow spectral bandwidth. Measurements did not confirm the theoretical predictions concerning an increase of temperature for larger particles. On the contrary, larger particles in richer premixed flames exhibit a lower 400/700 signal ratio. This can probably be attributed to small differences in the refractive index of soot.     

The effect of particle aggregation on the absorption and emission properties of mono- and polydisperse soot aggregates

This study concerns the effect of soot-particle aggregation on the soot temperature derived from the signal ratio in two-color laser-induced incandescence measurements. The emissivity of aggregated fractal soot particles was calculated using both the commonly used Rayleigh–Debye–Gans fractal-aggregate theory and the generalized Mie-solution method in conjunction with numerically generated fractal aggregates of specified fractal parameters typical of flame-generated soot. The effect of aggregation on soot temperature was first evaluated for monodisperse aggregates of different sizes and for a lognormally distributed aggregate ensemble at given signal ratios between the two wavelengths. Numerical calculations were also conducted to account for the effect of aggregation on both laser heating and thermal emission at the two wavelengths for determining the effective soot temperature of polydisperse soot aggregates. The results show that the effect of aggregation on laser energy absorption is important at low fluences. The effect of aggregation on soot emissivity is relatively unimportant in LII applications to typical laminar diffusion flames at atmospheric pressure, but it can become more important in flames at high pressures due to larger primary particles and wider aggregate distributions associated with enhanced soot loading.     

Visualization of soot formation from evaporating fuel films by laser-induced fluorescence and incandescence

Late-evaporating liquid fuel wall-films are considered a major source of soot in spark-ignition direct-injection (SIDI) engines. In this study, a direct-injection model experiment was developed to visualize soot formation in the vicinity of evaporating fuel films. Isooctane is injected by a multi-hole injector into the optically accessible part of a constant-flow facility at atmospheric pressure. Some of the liquid fuel impinges on the quartz-glass windows and forms fuel films. After spark ignition, a turbulent flame front propagates through the chamber, and subsequently sooting combustion is detected near the fuel films. Overlapping laser light sheets at 532 and 1064 nm excite laser-induced fluorescence (LIF) of polycyclic aromatic hydrocarbons (PAH) -potential soot precursors- and laser-induced incandescence (LII) of soot, respectively. The 532 nm light sheet has low fluence to avoid the excitation of LII. The LII and LIF signals are detected simultaneously and spectrally separated on two cameras. In complementary line-of-sight imaging, the fuel spray, chemiluminescence, and soot incandescence are captured with a high-speed color camera. In separate experiments, toluene is added to the isooctane as a fluorescent tracer and excited by pulsed 266 nm flood illumination. From images of the LIF signal, the fuel-films’ thickness and mass evolutions are evaluated. The films survive the entire combustion event. PAH LIF is found in close vicinity of the evaporating fuel films. Soot is found spatially separated from, but adjacent to the PAH, both with high spatial intermittency. Average images additionally indicate that soot is formed with a much higher spatial intermittency than PAH. Images from the color camera show soot incandescence earlier and in a similar region compared to soot LII. Chemiluminescence downstream of the soot-forming region is thought to indicate the subsequent oxidation of fuel, soot, and PAH.     

Laser-induced incandescence technique to identify soot nucleation and very small particles in low-pressure methane flames

This paper presents the study we carried out on the formation of soot particles in low-pressure premixed CH₄/O₂/N₂ flames by using Laser-Induced Incandescence (LII). Flames were stabilised at 26.6 kPa (200 torr). Four different equivalence ratios were tested (Φ = 1.95, 205, 2.15 and 2.32), Φ = 1.95 corresponding to the equivalence ratio for which LII signals begin to be measurable along the flame. The evolution of the LII signals with laser fluence (fluence curve), time (temporal decay) and emission wavelength is reported at different heights above the burner. We specifically took advantage of the low-pressure conditions to probe with a good spatial resolution the soot inception zone of the flames. Significant different behaviours of the fluence curves are observed according to the probed region of the flames and Φ. In addition, while the surface growth process is accompanied by an increase in the LII decay-times (indicator of the primary particle diameter) at higher Φ, decay-times become increasingly short at lower Φ reaching a constant value along the flame at Φ = 1.95. These behaviours are consistent with the detection of the smallest incandescent particles in the investigated flames, these particles having experienced very weak surface growth. Flame modelling including soot formation has been implemented in flames Φ = 2.05 and 2.32. Experimental quantitative soot volume fraction profiles were satisfactorily reproduced by adjusting the fraction of reactive soot surface available for reactions. The qualitative variation of the computed soot particle diameter and the relative weight of surface growth versus nucleation were consistent with the experimental observations.     

Soot formation characteristics in a lab-scale turbulent pulverized coal flame with simultaneous planar measurements of laser induced incandescence of soot and Mie scattering of pulverized coal

Soot formation characteristics of a lab-scale pulverized coal flame were investigated by performing carefully controlled laser diagnostics. The spatial distributions of soot volume fraction and the pulverized coal particles were measured simultaneously by laser induced incandescence (LII) and Mie scattering imaging, respectively. In addition, the radial distributions of the soot volume fraction were compared with the OH radical fluorescence, gas temperature and oxygen concentration obtained in our previous studies [1], [2]. The results indicated that the laser pulse fluence used for LII measurement should be carefully controlled to measure the soot volume fraction in pulverized coal flames. To precisely measure the soot volume fraction in pulverized coal flames using LII, it is necessary to adjust the laser pulse fluence so that it is sufficiently high to heat up all the soot particles to the sublimation temperature but also sufficiently low to avoid including a too large of a change in the morphology of the soot particles and the superposition of the LII signal from the pulverized coal particles on that from the soot particles. It was also found that the radial position of the peak LII signal intensity was located between the positions of the peak Mie scattering signal intensity and peak OH radical signal intensity. The region, in which LII signal, OH radical fluorescence and Mie scattering coexisted, expanded with increasing height above the burner port. It was also found that the soot formation in pulverized coal flames was enhanced at locations where the conditions of high temperature, low oxygen concentration and the existence of pulverized coal particles were satisfied simultaneously.     

Numerical investigation of the effect of signal trapping on soot measurements using LII in laminar coflow diffusion flames

Laser-induced incandescence has been rapidly developed into a powerful diagnostic technique for measurements of soot in many applications. The incandescence intensity generated by laser-heated soot particles at the measurement location suffers the signal trapping effect caused by absorption and scattering by soot particles present between the measurement location and the detector. The signal trapping effect was numerically investigated in soot measurements using both a 2D LII setup and the corresponding point LII setup at detection wavelengths of 400 and 780 nm in a laminar coflow ethylene/air flame. The radiative properties of aggregated soot particles were calculated using the Rayleigh–Debye–Gans polydisperse fractal aggregate theory. The radiative transfer equation in emitting, absorbing, and scattering media was solved using the discrete-ordinates method. The radiation intensity along an arbitrary direction was obtained using the infinitely small weight technique. The contribution of scattering to signal trapping was found to be negligible in atmospheric laminar diffusion flames. When uncorrected LII intensities are used to determine soot particle temperature and the soot volume fraction, the errors are smaller in 2D LII setup where soot particles are excited by a laser sheet. The simple Beer–Lambert exponential attenuation relationship holds in LII applications to axisymmetric flames as long as the effective extinction coefficient is adequately defined.     

Investigations of soot formation in an optically accessible gasoline direct injection engine by means of laser-induced incandescence (LII)

This study presents the results of laser-induced incandescence (LII) measurements in an optically accessible gasoline direct injection engine. The focus was to evaluate LII as a particle measurement technique which is able to provide a deeper understanding of the underlying reaction and formation processes of soot in order to optimize the injection system to reduce exhaust gas emissions. A comparison of time-resolved LII, based on the model described by Michelsen, with an Engine Exhaust Particle Sizer (EEPS) was performed. In this context, the air–fuel ratio, the injection pressure and the injection timing have been varied while applying the measurement techniques in the exhaust system. In case of a variation of the air–fuel ratio, two-dimensional LII has been performed in the combustion chamber additionally. For each measurement, the Filter Smoke Number (FSN) was taken into account as well. Finally, a good agreement of the different techniques was achieved. Moreover, we found that by combining time-resolved LII and EEPS a differentiation of primary particles and agglomerates is possible. Consequently, a determination of the processes in the combustion chamber and agglomeration in the exhaust gas is feasible.     

Experimental comparison of soot formation in turbulent flames of Diesel and surrogate Diesel fuels

Soot formation is compared in turbulent diffusion flames burning a commercial Diesel and two Diesel surrogates containing n-decane and α-methylnaphthalene. A burner equipped with a high-efficiency atomisation system has been specially designed and allows the stabilisation of liquid fuels flames with similar hydrodynamics conditions. The initial surrogate composition (70% n-decane, 30% α-methylnaphthalene) was previously used in the literature to simulate combustion in Diesel engines. In this work, a direct comparison of Diesel and surrogates soot tendencies is undertaken and relies on soot and fluorescent species mappings obtained respectively by Laser-Induced Incandescence (LII) at 1064 nm and Laser-Induced Fluorescence at 532 nm. LIF was assigned to soot precursors and mainly to high-number ring Polycyclic Aromatic Hydrocarbons (PAH). The initial surrogate was found to form 40% more soot than the tested Diesel. Consequently, a second surrogate containing a lower α-methylnaphthalene concentration (20%) has been formulated. That composition which presents a Threshold Soot Index (TSI) very close to Diesel one is also consistent with our Diesel composition that indicates a relatively low PAH content. The spatially resolved measurements of soot and fluorescent soot precursors are quite identical (in shape and intensity) in the Diesel and in the second surrogate flames. Furthermore the concordance of the LII temporal decays suggests that a similar growth of the primary soot particles has occurred for Diesel and surrogates. In addition, the comparison of the LII fluence curves indicates that physical/optical properties of soot contained in the different flames might be similar. The chemical composition present at the surface of soot particles collected in Diesel and surrogate flames has been obtained by laser-desorption ionisation time-of-flight mass spectrometry. An important difference is found between Diesel and surrogate samples indicating the influence of the fuel composition on soot content.     

Endoscopic fuel film,chemiluminescence, and soot incandescence imaging in a direct-injection spark-ignition engine

In direct-injection spark-ignition engines, fuel films formed on the piston surface due to impinging sprays are a major source of soot. Previous studies investigating the fuel films and their correlation to soot production were mostly performed in model experiments or optical engines. These experiments have different operating conditions compared to commercial engines. In this work, fuel films and soot are visualized in an all-metal engine with endoscopic access via laser-induced fluorescence (LIF) and natural incandescence, respectively. Gasoline and a mixture of isooctane/toluene were used as fuel for the experiments. The fuel films were excited by 266 nm laser pulses and visualized by an intensified CCD camera through a modular UV endoscope. Gasoline yielded much higher signal-to-noise ratio, and this fuel typically took an order of magnitude longer to evaporate than isooctane/toluene. The effects of injection time, injection pressure, engine temperature, and combustion on the fuel-film evaporation time were investigated. This film survival time was reduced with higher engine temperature, higher injection pressure, and later injection time, with engine temperature being the most significant parameter, whereas skip-fired combustion had very little effect on the film survival time. In complementary experiments, LIF from fuel films and soot incandescence were simultaneously visualized by an intensified double-frame CCD camera. At lower engine temperatures the fuel films remained distinct, and soot formation was limited to regions above the films, whereas at higher temperatures, fuel films, and hence the soot, appeared to be spread over the whole piston surface. Finally, high-speed imaging showed the spray, chemiluminescence, and soot incandescence, with results broadly consistent with fuel-film LIF and soot incandescence imaging.     

Influence of pressure on near nozzle flow field and soot formation in laminar co-flow diffusion flames

Soot formation from combustion devices, which tend to operate at high pressure, is a health and environmental concern, thus investigating the effect of pressure on soot formation is important. While most fundamental studies have utilised the co-flow laminar diffusion flame configuration to study the effect of pressure on soot, there is a lack of investigations into the effect of pressure on the flow field of diffusion flames and the resultant influence on soot formation. A recent work has displayed that recirculation zones can form along the centreline of atmospheric pressure diffusion flames. This present work seeks to investigate whether these zones can form due to higher pressure as well, which has never been explored experimentally or numerically. The CoFlame code, which models co-flow laminar, sooting, diffusion flames, is validated for the prediction of recirculation zones using experimental flow field data for a set of atmospheric pressure flames. The code is subsequently utilised to model ethane-air diffusion flames from 2 to 33 atm. Above 10 atm, recirculation zones are predicted to form. The reason for the formation of the zones is determined to be due to increasing shear between the air and fuel steams, with the air stream having higher velocities in the vicinity of the fuel tube tip than the fuel stream. This increase in shear is shown to be the cause of the recirculation zones formed in previously investigated atmospheric flames as well. Finally, the recirculation zone is determined as a probable cause of the experimentally observed formation of a large mass of soot covering the entire fuel tube exit for an ethane diffusion flame at 36.5 atm. Previously, no adequate explanation for the formation of the large mass of soot existed.     

Relationship between soot volume fraction and LII signal in AC-LII: effect of primary soot particle diameter polydispersity

Theoretical analysis and numerical calculations were conducted to investigate the relationship between soot volume fraction and laser-induced incandescence (LII) signal within the context of the auto-compensating LII technique. The emphasis of this study lies in the effect of primary soot particle diameter polydispersity. The LII model was solved for a wide range of primary soot particle diameters from 2 to 80 nm. For a log-normally distributed soot particle ensemble encountered in a typical laminar diffusion flame at atmospheric pressure, the LII signals at 400 and 780 nm were calculated. To quantify the effects of sublimation and differential conduction cooling on the determined soot volume fraction in auto-compensating LII, two new quantities were introduced and demonstrated to be useful in LII study: an emission intensity distribution function and a scaled soot volume fraction. When the laser fluence is sufficiently low to avoid soot mass loss due to sublimation, accurate soot volume fraction can be obtained as long as the LII signals are detected within the first 200 ns after the onset of the laser pulse. When the laser fluence is in the high fluence regime to induce significant sublimation, however, the LII signals should be detected as early as possible even before the laser pulse reaches its peak when the laser fluence is sufficiently high. The analysis method is shown to be useful to provide guidance for soot volume fraction measurements using the auto-compensating LII technique.     

Combination of LII and extinction measurements for determination of soot volume fraction and estimation of soot maturity in non-premixed laminar flames

The measurement of soot and soot precursors is important for understanding the formation of soot particles in flames. In this paper, we use the difference between laser-induced incandescence (LII) and two-dimensional extinction measurements to assess the contribution of soot precursors to the extinction measurement. LII measurements are performed with a high spatial resolution of 100 µm to determine the soot volume fraction (f _V) in a laminar ethylene/air non-premixed flame at the standard Gülder conditions. While LII is specific to mature soot only, the extinction data represent attenuation due to mature and young soot (absorption and elastic scattering) and also absorption by soot precursors. The difference between the two measurements indicates the contribution of soot precursors and allows a determination of the maturity of soot. This is important knowledge for those using extinction techniques to measure soot concentration, as the contribution from soot precursors may lead to an overestimation of the mature soot concentration. Further, regions with high soot-precursor concentrations, which lead to soot formation, can be identified.     

Water vapour effects on temperature and soot loading in ethylene flames in hot and vitiated coflows

Flames in hot, low oxygen environments exist in a variety of practical applications. These conditions result in significant mixing between fuel and combustion products, such as water vapour, or diluents included for emissions control. The chemical and physical effects of water vapour as a diluent are investigated in a series of ethylene flames in a jet in hot coflow burner to determine the effects on temperature and soot fields. The combined analyses of photographs, non-linear excitation regime two-line atomic fluorescence (NTLAF) of indium, planar laser-induced incandescence (LII) and one-dimensional opposed-flow flame simulations demonstrate the dominance of the chemistry, driven by the hot and vitiated oxidant, in soot reduction. Although photographs appear to suggest that both highly vitiated coflows, and highly diluted jet flames have global effect on the flames, detailed measurements reveal significantly different trends in their soot and temperature fields. The chemical contribution of water vapour as a reactant, as a third-body in ethylene decomposition and a source of H and OH in the rich mixture is further described, and trends subsequently identified, in the context of formation of polycyclic aromatic hydrocarbons and soot reduction.     

Experimental and theoretical comparison of spatially resolved laser-induced incandescence (LII) signals of soot in backward and right-angle configuration

In-situ measurements of soot volume fraction in the exhausts of jet engines can be carried out using the laser-induced incandescence (LII) technique in backward configuration, in which the signal is detected in the opposite direction of the laser beam propagation. In order to improve backward LII for quantitative measurements, we have in this work made a detailed experimental and theoretical investigation in which backward LII has been compared with the more commonly used right-angle LII technique. Both configurations were used in simultaneous visualization experiments at various pulse energies and gate timings in a stabilized methane diffusion flame. The spatial near-Gaussian laser energy distribution was monitored on-line as well as the time-resolved LII signal. A heat and mass transfer model for soot particles exposed to laser radiation was used to theoretically predict both the temporal and spatial LII signals. Comparison between experimental and theoretical LII signals indicates similar general behaviour, for example the broadening of the spatial LII distribution and the hole-burning effect at centre of the beam due to sublimation for increasing laser pulse energies. However, our comparison also indicates that the current heat and mass transfer model overpredicts signal intensities at higher fluence, and possible reasons for this behaviour are discussed. PACS 42.62.Fi; 44.40.+a     

Soot-visualization strategies using laser techniques

Strategies for spatially resolved soot volume-fraction measurements have been investigated in sooting laboratory flames with known soot characteristics. Two techniques were compared: Laser-Induced Fluorescence in C₂ from Laser-Vaporized Soot (LIF(C₂)LVS), and Laser-Induced Incandescence of soot (LII). The LII signal is the increased temperature radiation from soot particles which have been heated to temperatures of several thousand degrees as a consequence of absorption of laser radiation. The LIF(C₂)LVS technique is based on the production of C₂ radicals from laser-vaporized soot which occurs for laser intensities ≥10⁷ W/cm². A laser wavelength is chosen such that besides vaporizizng the soot, it also excites the C₂ radicals, and the subsequent C₂ fluorescence signal is detected. The signals from both techniques showed good correlation with soot volume fractions in the studied flame. The dependence of the signals on experimental parameters was studied, and the influence of interfering radiation, such as background flame luminosity and fluorescence from polyaromatic hydrocarbons, on studied signals was established. The potential of the two techniques for imaging of soot volume fractions in laboratory flames was demonstrated. Advantages and disadvantages of the studied techniques are discussed.