Thick porous tungsten trioxide films by anodization of tungsten in fluoride containing phosphoric acid electrolyte

In the present work, we report on the formation of mesoporous thick tungsten trioxide films grown on tungsten foil by anodization in fluoride containing concentrated phosphoric acid (85%) electrolyte. Under optimized experimental conditions, mesoporous WO₃ films with a thickness up to approximately 2 μm are formed. SEM shows the films to consist of a connected network with a typical pore and feature diameter of ca 50 nm. These films as formed are amorphous and can be annealed to orthorhombic WO₃ structure. These thick porous films can show significant enhanced electrochromic and improved photocatalytic properties.     

High‐performance Flexible Complementary Electrochromic Device Based on Plasma Modified WO3 Nano Hybrids and V2O5 Nanofilm with Low Operation Voltages

Tungsten trioxide‐poly(3,4‐ethylenedioxythiophene) (WO₃‐PEDOT) and tungsten trioxide‐polyfuran (WO₃‐PFu) were prepared by rf rotating plasma polymerization. Electrochromic hybrid thin films were fabricated onto flexible polyethylene terephthalate (PET)/ indium tin oxide (ITO) film using electron beam evaporation method. In order to deeply characterize all films, scanning electron microscopy‐energy dispersive X‐ray spectroscopy (SEM‐EDS) and electrochemical impedance spectroscopy (EIS) techniques were used. The counter electrode effect on plasma modified WO₃ nano hybrids‐based electrochromic devices (ECDs) was evaluated. By incorporating flexible vanadium pentoxide (V₂O₅) film as counter electrode, complementary ECDs were constructed through combining the hybrid flexible films (WO₃‐PEDOT, WO₃‐PFu) as working electrodes, which exhibit highly efficient electrochromic performance with low voltage operation. Especially, WO₃‐PEDOT/V₂O₅‐based ECD owns a high optical modulation of 61.5 % at 750 nm driven by −1.0 V (coloration) and +1 V (bleaching) with fast response times (coloration time: 13.58 s, bleaching time: 8.07 s) and a high coloration efficiency of 527 cm² C⁻¹. This study can supply useful and efficient avenue for designing flexible complementary electrochromic device for energy‐saving flexible electronics.     

Electrochromic responses of low-temperature-annealed tungsten oxide thin films in contact with a liquid and a polymeric gel electrolyte

Thin films of tungsten trioxide (WO₃) for electrochromic application were synthesized by potentiostatic method by using a peroxytungstic acid as a solution precursor. The morphology of the films with and without postthermal annealing was analyzed by atomic force microscopy. When they were in contact with the liquid electrolyte (LiI in propylene carbonate, PC) and under alternatively applied negative (−1.5 V) and positive (+1.0 V) potentials, the transient optical transmittance modulations at wavelength of 650 nm of the as-deposited and 60 °C annealed WO₃ samples were higher than that of 100 °C annealed WO₃ films, and the switching times between the colored and bleached states were related to the surface morphology of the WO₃ films. In polymeric gel electrolyte (LiI and polymethyl methacrylate in PC) devices, longer time was required for complete coloration as well as bleaching process compared with the liquid one. A parametric analysis was made for each of the transient optical transmittance curves of WO₃-based electrochromic devices to extract the values of the response time in coloration (reduction) and bleaching (oxidation) processes. It concludes that the coloration process was determined by the exchange of current density at the electrolyte–WO₃ interface and a possible inhomogeneous interfacial potential for ion intercalation retards the effective coloration time. The bleaching process seems to be controlled by the space charge-limited lithium ion diffusion in WO₃ electrode and the ionic conductivity of the electrolyte as well.     

Preparation and characterization of the Ti/IrO<Subscript>2</Subscript>/WO<Subscript>3</Subscript> as supercapacitor electrode materials

WO₃ films have been prepared onto IrO₂-coated Ti substrate by electro-deposition, and as-deposited and annealed films have been characterized by using Raman spectroscopy. It was found that the asdeposited film consists of orthorhombic WO₃ · H₂O phase, which transforms to amorphous WO₃ by annealing at 250°C and to monoclinic phase by annealing at and above 350°C. All electrochemical experiments were carried on Ti/IrO₂/WO₃ annealed at 450°C. The open-circuit potential could change significantly due to the hydration of the coating film. However this process is fairly slow. Reproducible voltammograms could be obtained quickly, further revealing high electrochemical stability of the Ti/IrO₂/WO₃ electrode. And the shapes of CV show the approximate rectangular mirror image, showing the typical characteristic of capacitive behavior. The specific capacitance obtained at a scan rate of 50 mV s⁻¹ is 46 F g⁻¹.     

One‐step electrodeposition of amorphous carbon films containing WO3 with high conductivity and good wettability

Tungsten trioxide‐incorporated hydrogenated amorphous carbon (WO₃/a‐C:H) films have been fabricated on a single‐crystal silicon wafer by liquid phase electrodeposition using methanol as carbon source and tungsten carbonyl as incorporated reagent. The morphology, composition and structure of the films have been investigated by SEM, XPS, Raman scattering spectroscopy, Fourier transform infrared spectroscopy (FTIR) and Transmission electron microscope (TEM), respectively. The effects of WO₃ incorporation on the electrical and wetting properties were studied in detail. The characterization results showed that tungsten trioxide nanocrystalline particles with diameters in the range of 10–20 nm were homogenously embedded in the amorphous carbon films. Also, the electrical conductivity and wetting ability of the films were strongly improved due to the contribution of the tungsten trioxide. Copyright © 2010 John Wiley & Sons, Ltd.     

Decoration of TiO2 nanotube layers with WO3 nanocrystals for high-electrochromic activity

We report a simple approach to decorate ordered TiO₂ nanotube (TiNT) layers with tungsten trioxide nanocrystallites by the controlled hydrolysis of a WCl₆ precursor. These WO₃ nanocrystallites, when formed, are amorphous, but can be annealed to a monoclinic crystal structure. The WO₃ crystallites on the TiO₂ nanotube skeleton are electrochemically active, and hence ion insertion reactions are possible. As a result, the decorated nanotube layers show remarkable enhancement of the electrochromic properties. In particular, a significantly lower threshold voltage and an increased electrochromic contrast can be achieved compared with unloaded (neat) TiO₂ nanotube layers.     

无模板电化学沉积法制备多孔WO3·2H2O薄膜及其电致变色性能

二水合氧化钨(WO₃·2H₂O)因其独特的层状结构且富含层间结构水,与无水WO₃相比显示出更加优异的电致变色性能。我们采用简单、无模板的阴极电化学沉积方法,成功在氧化铟锡(ITO)导电玻璃基底上制备了WO₃·2H₂O薄膜。通过改变电沉积液中过氧化氢(H₂O₂)的加入量优化沉积液的成分,获得了具有纳米多孔结构的薄膜。由此制备的WO₃·2H₂O薄膜显示出大的光学对比度(633 nm处的光学对比度大于90%)、快速的响应速度(着色、褪色时间均小于10 s),以及良好的循环稳定性(经10 000次循环后,光学对比度仍保持在90%左右)。     

Fabricating polypyrrole/tungsten oxide hybrid based electrochromic devices using different ionic liquids

A facile approach of polypyrrole (PPy)/tungsten oxide (WO₃) composites electrosynthesized in ionic liquids for fabrication of electrochromic devices is discussed. The electrochromic properties of PPy/tungsten oxide nanocomposite films (PPy/WO₃) prepared in the presence of four different ionic liquids, 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMIMBF₄), 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆), 1‐butyl‐3‐methylimidazolium bis(trifluoromethylsulfonyl) imide (BMIMTFSI), and 1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl) imide (BMPTFSI) were investigated in detail. Cyclic voltammetry results revealed that PPy/WO₃ nanocomposite films have much more electrochemical activity than those of WO₃ and PPy film. The electrochromic contrast, coloration efficiency, and switching speed of the composite films were determined for electrochromic characteristics. The maximum contrast and the maximum coloration efficiency values were measured as 33.25% and 227.89 cm²/C for the PPy/WO₃/BMIMTFSI composite film. Copyright © 2015 John Wiley & Sons, Ltd.     

Ion conductivity of poly(ethylene oxide)-based polyurethane networks containing alkali metal salts

Ion conductivity of poly(ethylene oxide) (PEO)-based polyurethane networks containing alkali metal salts has been investigated. Consequently, it has been revealed that the conductivity is dependent on the following parameters: lattice energy of the alkali metal salt, concentration of alkali metal salt, and the cross-linking density of the network polymer (which is a function both of the amount of cross-linking agent and the molecular weight of PEO). Under optimal conditions, the conductivity at ambient temperature corresponded to 2.51 × 10^?5 Scm^?1, which is greater than that of a typical alkali metal-PEO system by a factor of about 10² to 10³. Moreover, from the standpoint of the application to electrochromic displays (ECD), tensile bond strength between the polymer electrolytes and tungsten trioxide (WO₃), which is the most promising electrochromic material, has been evaluated. The bonding strength of the bond of WO₃ with the present electrolyte has been found to be much larger than that of the alkali metal-PEO system.     

介孔氧化钨电色薄膜的制备与性能研究

采用一种新的非离子型gemini表面活性剂结构导向模板, 成功制备了介孔氧化钨薄膜. 通过SAXRD, TEM和N₂吸附-脱附等方法考察薄膜的制备和微结构特性, 发现获得的产物具有三维蠕虫介孔结构, 比表面积可达145.5 m²• g^－1. 测定了该薄膜在无水高氯酸锂/碳酸丙烯酯电解质溶液中的循环伏安和电致变色性能, 并与无模板薄膜进行了对比研究. 研究表明, 由于具有更大的电化学活性比表面, 纳米介孔氧化钨薄膜表现出增强的电色性能, 在633 nm波长处的透过率调制幅度可达60%以上, 着色效率为51.7 cm²•C^－1.     

Electrochromic properties of WO<Subscript>3</Subscript> and WO<Subscript>3</Subscript>:P thin films

WO₃ and WO₃:P (5 mol% H₃PO₄) thin films were prepared using the sol-gel route and the electrochromic properties of the films were investigated using in situ spectroelectrochemical methods. The measurements were performed in propylene carbonate solution with 0.1 M LiClO₄ as electrolyte. During the cathodic polarization at –0.8 V a blue coloration is observed with a reversible variation between 14% and 84% of the transmittance at λ=633 nm. The kinetics for the bleaching process is faster for the WO₃:P film than for the undoped WO₃ film. Electronic Publication     

无模板电化学沉积法制备多孔WO3·2H2O薄膜及其电致变色性能

二水合氧化钨(WO₃·2H₂O)因其独特的层状结构且富含层间结构水,与无水WO₃相比显示出更加优异的电致变色性能。我们采用简单、无模板的阴极电化学沉积方法,成功在氧化铟锡(ITO)导电玻璃基底上制备了WO₃·2H₂O薄膜。通过改变电沉积液中过氧化氢(H₂O₂)的加入量优化沉积液的成分,获得了具有纳米多孔结构的薄膜。由此制备的WO₃·2H₂O薄膜显示出大的光学对比度(633nm处的光学对比度大于90%)、快速的响应速度(着色、褪色时间均小于10s),以及良好的循环稳定性(经10000次循环后,光学对比度仍保持在90%左右)。     

Effect of tungsten oxide loading on metathesis activity of ethene and 2-butene over WO<Subscript>3</Subscript>/SiO<Subscript>2</Subscript> catalysts

The metathesis of ethene and 2-butene to propene was studied over WO₃/SiO₂ catalysts with various WO₃ loadings (2, 4, 8, 12, 16, and 24 wt%). The 2-butene conversion and propene selectivity increased greatly with WO₃ loading increasing from 2 to 8 wt%, reached maximum at 8–12 wt% WO₃ loading, and then decreased when the WO₃ loading was higher than 12 wt%. From the above results and taking the economics into account, the optimal amount of WO₃ loading was ~8 wt%. The catalysts were characterized by physico-chemical and spectroscopic techniques to elucidate the effect of different tungsten oxide loadings on the metathesis reactivity of ethene and 2-butene. The characterization data indicated that three types of tungsten species (i.e., surface tetrahedral tungsten species, surface octahedral polytungstate species, and WO₃ crystallites) were present in the catalysts. It was found that WO₃ was not the active centers, and surface tetrahedral tungsten species might be more active than octahedral polytungstate species in metathesis reaction. The reduced form of tungsten species [W⁺⁴, W⁺⁵, and W^+(6−y) (0 < y < 1)] may be the suitable state of W species acting as metathesis active centers.     

Synthesis and characterization of chemically grown electrochromic tungsten oxide

Tungsten oxide thin films, which are cathodic coloration materials that are used in electrochromic devices, were prepared by a chemical growth method and their electrochromic properties were investigated. The thin films of WO₃ were deposited onto electrically conducting substrates: fluorine doped tin oxide coated glass (FTO) with sheet resistance of about 10 Ω/cm. Transparent, uniform and strongly adherent thin film samples of WO₃ were studied for their structural, morphological, optical and electrochromic properties. The XRD data confirmed the monoclinic crystal structure of WO₃ thin films. The direct band gap Eg for the films was found to be 2.95 eV which is good for electrochromic device application. The electrochromism of WO₃ thin film was evaluated in 0.5 M LiClO₄/propylene carbonate for Li⁺ intercalation. Electrochromic properties of WO₃ thin films were studied with the help of Cyclic Voltammetry (CV), Chronoamperometry (CA) and Chronocoulometry (CC) techniques.     

Crystallographically oriented mesoporous WO3 films: synthesis, characterization, and applications.

Mesoporous semiconducting films consisting of preferentially orientated monoclinic-phase nanocrystals of tungsten trioxide have been prepared using a novel version of the sol-gel method. Transformations undergone by a colloidal solution of tungstic acid, stabilized by an organic additive such as poly(ethylene glycol) (PEG) 300, as a function of the annealing temperature have been followed by means of a confocal Raman microscope. The shape and size of WO3 nanoparticles, the porosity, and the properties of the films depend critically on preparation parameters, such as the tungstic acid/PEG ratio, the PEG chain length, and the annealing conditions. Well-crystallized WO3 films combine excellent photoresponse to the blue region of the solar spectrum, up to 500 nm, with good transparency at wavelengths larger than 550 nm. Particular applications of these nanocrystalline WO3 films include photoelectrochemical and electrochromic devices.     

WO<Subscript>3</Subscript> thin film coating from H<Subscript>2</Subscript>O-controlled peroxotungstic acid and its electrochromic properties

We prepared PTA coating solution by hot plate evaporation, N₂ bubbling evaporation, and rotary evaporation. N₂ bubbling and rotary evaporation are very efficient way to synthesize PTA which reduces the synthesis process time to 1/5, compared to hot plate evaporation method. Another strong point is that N₂ bubbling and rotary evaporation make it possible to control excess hydrogen peroxide and water contents in PTA. The PTA formula were WO₃·0.13H₂O₂·10.0H₂O for hot plate method, WO₃·0.16H₂O₂·7.1H₂O for N₂ bubbling method, and WO₃·0.15H₂O₂·3.00H₂O for rotary evaporation method. Thermal analysis and mass spectroscopy analysis show that water is evaporated at around 100 °C and hydrogen peroxide is dissociated at the range of 150 and 250 °C. Amorphous phase of WO₃ thin film prepared from rotary evaporated PTA solution has the best electrochromic property, light transmission difference from 91% at its bleached state and 5.5% colored state, and charge density of 22 mC/cm². It is thought that the control of excess hydrogen peroxide and water contents in PTA is very important to enhance the electrochromic properties of WO₃ thin film.     

Influence of PEG additive and annealing temperature on structural and electrochromic properties of sol–gel derived WO<Subscript>3</Subscript> films

Sol–gel derived tungsten oxide (WO₃) films have been deposited by spin coating route using acetylated peroxotungstic acid (APTA) or a mixture of APTA and polyethylene glycol (PEG) dissolved in ethanol as the precursor solution, followed by thermal treatment in air. The influence of PEG additive and annealing temperature on the structural and electrochromic (EC) behavior of the films have been investigated. For films annealed at 300 °C, a porous nanocrystalline/amorphous microstructure was obtained in the WO₃-PEG film, while monoclinic microstructure was formed in the pure WO₃ film. Moreover, for the WO₃-PEG films, the film microstructure was found to depend on the annealing temperature. Electrochemical studies indicate that the WO₃-PEG film annealed at 300 °C (WP-300) exhibits superior EC properties, which produces faster switching speed (t _c = 19 s, t _b = 3 s),better reversibility (K = 0.97) as well as higher optical modulation (ΔT = 32% at 550 nm) and coloration efficiency (η = 22 cm²/C at 550 nm). Our results suggest that PEG addition in combination with an appropriate annealing treatment can benefit the EC properties, arising from the ease of ion diffusion within the EC material, as evident from the nanocrystallines embedded into the amorphous matrix with a porous character.     

Optical Characteristics and Structure of Electrochromic Amorphous Tungsten Trioxide Films Electrodeposited from Aqueous Electrolytes

The structure of electrochromic amorphous tungsten trioxide films electrodeposited from an aqueous tungsten-containing electrolyte and specific features of the optical and electrochemical characteristics of these films in different stages of their reversible coloration in a 1 N H₂SO₄ solution were studied.     

Activation of methanol-tolerant carbon-supported RuSe<Subscript>x</Subscript> electrocatalytic nanoparticles towards more efficient oxygen reduction

An electrocatalytic system that utilizes tungsten oxide modified carbon-supported RuSe_x nanoparticles is developed and characterized here using transmission electron microscopy and such electrochemical diagnostic techniques as cyclic voltammetry and rotating ring-disk voltammetry, as well as upon its introduction (as cathode) to the low-temperature hydrogen–oxygen fuel cell. After the modification of RuSe_x catalytic centers with ultra-thin films of WO₃, the potential of oxygen reduction in 0.5 mol dm⁻³ H₂SO₄ (in the absence and presence of methanol) is shifted ca. 70 mV (under rotating disk voltammetric conditions) towards more positive values, and the percent formation (at ring) of the undesirable hydrogen peroxide has decreased approximately twice when compared to the WO₃-free system. Relative to bare electrocatalyst, an increase of power density from 75 to 100 mW cm⁻² (at 300 mA cm⁻²) has been observed upon utilization of WO₃-modified RuSe_x in polymer electrolyte membrane fuel cell at 80 °C. In comparison to Vulcan-supported Pt nanoparticles, the overall electrocatalytic performance of tungsten oxide modified carbon-supported RuSe_x nanoparticles is lower, but the latter system is practically insensitive to the presence of methanol even at 0.5 mol dm⁻³ level. Dedicated to Professor Dr. Algirdas Vaskelis on the occassion of his 70th birthday.     

Preparation and photoelectrocatalytic activity of a nano-structured WO3 platelet film

A tungsten trioxide (WO₃) film was prepared by calcination from a precursor paste including suspended ammonium tungstate and polyethylene glycol (PEG). The ammonium tungstate suspension was yielded by an acid-base reaction of tungstic acid and an ammonium solution followed by deposition with ethanol addition. Thermogravimetric (TG) analysis showed that the TG profile of PEG is significantly influenced by deposited ammonium tungstate, suggesting that PEG is interacting strongly with deposited ammonium tungstate in the suspension paste. X-ray diffraction (XRD) data indicated that the WO₃ film is crystallized by sintering over 400 °C. The scanning electron microscopic (SEM) measurement showed that the film is composed of the nano-structured WO₃ platelets. The semiconductor properties of the film were examined by Mott-Schottky analysis to give flat band potential E_FB=0.30 V vs. saturated calomel reference electrode (SCE) and donor carrier density N_D=2.5×10²² cm⁻³, latter of which is higher than previous WO₃ films by two orders of magnitude. The higher N_D was explained by the large interfacial heterojunction area caused by the nano-platelet structure, which apparently increases capacitance per a unit electrode area. The WO₃ film sintered at 550 °C produced 3.7 mA cm⁻² of a photoanodic current at 1.2 V vs. SCE under illumination with a 500 W xenon lamp due to catalytic water oxidation. This photocurrent was 4.5-12.8 times higher than those for the other control WO₃ films prepared by similar but different procedures. The high catalytic activity could be explained by the nano-platelet structure. The photocurrent was generated on illumination of UV and visible light below 470 nm, and the maximum incident photon-to-current conversion efficiency (IPCE) was 47% at 320 nm at 1.2 V. Technically important procedures for preparation of nano-structured platelets were discussed.