Thermal properties of single walled carbon nanotube‐silicone nanocomposites

The effect of single walled carbon nanotube (SWCNT) fillers on the low temperature thermal properties and curing behavior of SWCNT‐silicone nanocomposite are reported for the first time. The SWCNT‐silicone composites were prepared by different mixing procedures and characterized by differential scanning calorimetry (DSC). Solution mix, with the aid of sonication and soaking achieved better dispersion of SWCNTs in the silicone. The adding of SWCNTs in polymer seriously hindered the curing of silicone elastomer. The hindrance increased with increasing concentration of SWCNT and the quality of dispersion. The glass transition temperatures (T_g) of the nanocomposites were found to be independent of the SWCNT addition, although, the steps in the heat capacity (Δc_p) of the glass transition were smaller with increasing SWCNTs concentration. The melt crystallization behavior was strongly dependent on the concentration and dispersion of SWCNT in the polymer. The cooling scan showed that the higher concentration and the better dispersion of SWCNTs in the silicone resulted in higher percentage of melt crystallization of this nanocomposite. The correlation of the change of thermal properties to the dispersion of CNT in polymer may be used to determine the quality of SWCNT dispersion in silicone polymer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1845–1852, 2008     

Bulk dispersion of single-walled carbon nanotubes in silicones using diblock copolymers

The interactions of a series of poly(3-decylthiophene)-block-polydimethylsiloxanes (P3DT-b-PDMS) with single-walled carbon nanotubes (SWNTs) are investigated. The formation of supramolecular complexes of P3DT-b-PDMS with SWNTs is studied in THF, toluene, xylenes, and CHCl₃, and the resulting complexes are characterized by UV-Vis-NIR absorption and fluorescence spectroscopy. The P3DT-b-PDMS-SWNT and P3DT-SWNT complexes are further incorporated into a commercially available silicone rubber formulation. Percolation thresholds of <0.02% (P3DT-b-PDMS-SWNT) and <0.05% (P3DT-SWNT) are measured. A decrease in the percolation threshold when using the block copolymer for nanotube dispersion is observed, suggesting that the presence of a covalently-linked PDMS block improves SWNT distribution in the silicone elastomer and allows a percolation network to form at low SWNT loadings. In addition, it is found that entanglement of the silicone block of P3DT-PDMS with bulk silicones results in anchoring of the nanotubes within the composite, and leads to reversible conductivity changes upon repeated stretching and relaxation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 265–273     

Hybridization of emitting polyfluorene with silicone

Polyfluorenes with pendant allyl groups were prepared by terpolymerization of 9,9‐dihexylfluorene‐2,7‐bis(trimethyleneborate), 2,7‐dibromo‐9,9‐bis(2‐allyloxyethyl)fluorene, and 4,7‐dibromo‐2,1,3‐benzothiazole, or 4,7‐dibromo‐2,1,3‐naphthoselenadiazole using Suzuki coupling reaction. The subsequent hydrosilylation reaction of these precursor polymers with ethoxydimethylsilane quantitatively converted the allyl groups to ethoxysilyl groups. Hybridization of the emitting polyfluorenes with silicone was successfully achieved by the solvent‐free sol–gel reaction of tetraethoxysilane and silanol‐terminated polydimethylsiloxane in the presence of the ethoxysilyl‐functionalized polyfluorenes. Fluorescence spectra of these luminescent silicones revealed that emitting polyfluorenes were dispersed homogeneously in the matrix of silicone without aggregation. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 622–628     

A versatile A2 + B3 approach to hyperbranched polyacenaphthenequinones

A series of hyperbranched polyacenaphthenequinones has been prepared by superelectrophilic aromatic substitution of (substituted) acenaphthenequinone and 1,3,5‐tris‐(4‐phenoxybenzoyl)benzene via a facile A₂ + B₃ approach. Because of the strongly increased reactivity of the second A functionality, gelation was efficiently avoided during the polymerization. The structure of the resulting polymer was characterized by NMR spectroscopy and gel permeation chromatography. Further modification of the hyperbranched polyacenaphthenequinone was explored both on the acenaphthenequinone and aromatic moieties. Moreover, the polymer modified through sulfonation was investigated as a water‐soluble acid catalyst for the degradation of biomass resources. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2596‐2603     

Thiol‐epoxy polymerization via an AB monomer: Synthetic access to high molecular weight poly(β‐hydroxythio‐ether)s

A synthetic route is developed for the preparation of an AB‐type of monomer carrying an epoxy and a thiol group. Base‐catalyzed thiol‐epoxy polymerization of this monomer gave rise to poly(β‐hydroxythio‐ether)s. A systematic variation in the reaction conditions suggested that tetrabutyl ammonium fluoride, lithium hydroxide, and 1,8‐diazabicycloundecene (DBU) were good polymerization catalysts. Triethylamine, in contrast, required higher temperatures and excess amounts to yield polymers. THF and water could be used as polymerization mediums. However, the best results were obtained in bulk conditions. This required the use of a mechanical stirrer due to the high viscosity of the polymerization mixture. The polymers obtained from the AB monomer route exhibited significantly higher molecular weights (M_w = 47,700, M_n = 23,200 g/mol) than the materials prepared from an AA/BB type of the monomer system (M_w = 10,000, M_n = 5400 g/mol). The prepared reactive polymers could be transformed into a fluorescent or a cationic structure through postpolymerization modification of the reactive hydroxyl sites present along the polymer backbone. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2040–2046     

Amphiphilic silicones prepared from branched PEO‐silanes with siloxane tethers

Amphiphilic silicones were prepared by the covalent incorporation of branched polyethylene oxide (PEO) via a siloxane tether. This was achieved by using six novel branched PEO‐silanes with varying siloxane tether lengths and PEO molecular weight (M_n). Each PEO‐silane was crosslinked via acid‐catalyzed sol–gel condensation with α,ω‐bis(Si‐OH)polydimethylsiloxane (PDMS) (M_n = 3000 g/mol) to yield six amphiphilic silicone films. Film surface hydrophilicity increased with siloxane tether length, particularly after exposure to an aqueous environment, indicating that the PEO segments were more readily driven to the surface. This effect was more pronounced for films prepared with PEO‐silanes containing lower M_n PEO segments. AFM was used to study surface reconstruction of films upon exposure to an aqueous environment. Adsorption of bovine serum albumin (BSA) and human fibrinogen (HF) proteins decreased with siloxane tether length, particularly after first exposing films to an aqueous environment. For a given siloxane tether length, relatively less BSA adsorbed onto films prepared with PEO‐silanes with lower M_n PEO segments whereas less HF adsorbed onto films prepared with PEO‐silanes with higher M_n PEO segments. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4108–4119, 2010     

Development and application of latent hydrosilylation catalysts [2]—Control of catalytic activity of platinum catalyst by polystyrene derivatives having propargyl moieties

A new thermal latent hydrosilylation catalyst on the basis of H₂PtCl₆ and polystyrene derivatives having propargyl moieties is described. The polystyrene derivatives having various propargyl moieties were obtained by the reaction of propargyl alcohols with poly(p‐chloromethylstyrene) or its copolymer with styrene. The polymer‐supported platinum catalysts were prepared by aging H₂PtCl₆ with these polymers in tetrahydrofuran at 30 °C for 12 h. In the presence of the polymers, the hydrosilylation activity of H₂PtCl₆ was found to be controlled thermally in the model reaction of trimethylsilane and triethylvinylsilane. Effective control of the crosslinking reaction of silicone resin was also achieved by using these latent catalyst systems. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 35–42, 2000     

Growth of poly(3,4‐ethylenedioxythiophene) films prepared by base‐inhibited vapor phase polymerization

Transparent [90% transmittance at 550 nm at a sheet resistance (R_s) of 279 Ω sq^?1] poly(3,4‐ethylenedioxythiophene) (PEDOT) films with electrical conductivities up to 1354 S cm^?1 are prepared using base‐inhibited vapor phase polymerization at atmospheric pressure. The influence of reaction conditions, such as temperature and growth time, on the film formation is investigated. A simple and convenient two‐electrode method is used for the in situ measurement of resistance, enabling to investigate the growth mechanism of polymer films and the influence of different parameters (relative humidity and the amount of oxidant) on the film growth. Low humidity exerts a detrimental effect on film growth and conductivity. In situ R_s measurements suggest that a large structural change occurs upon washing the PEDOT‐oxidant film. © 2014 Wiley Periodicals, Inc. J Polym Sci Part B: Polym. Phys. 2014 , 52, 561–571     

Viscoelastic properties of supramolecular soft materials with transient polymer network

A series of supramolecular soft materials with hydrogen bonded transient networks was prepared by blending carboxy‐terminated telechelic poly(ethyl acrylate) (PEA‐(COOH)₂) and polyethyleneimine (PEI). Effects of PEA‐(COOH)₂ molecular weight (M_PEA) and the blend ratio on the viscoelastic properties were investigated by rheological and small angle X‐ray scattering measurements. Rubbery plateau appeared by adding PEI due to network formation with ionic hydrogen bonded crosslinks between amines on PEI and carboxylic acids on PEA‐(COOH)₂. The highest temperature of a storage modulus‐loss modulus crossover as well as the highest flow activation energy was attained at a certain mole ratio of amines to carboxylic acids, irrelevant to M_PEA, indicating optimized supramolecular networks were achieved by stoichiometric balance of two functional groups. Since telechelic PEA‐(COOH)₂ serves as a network strand, the plateau modulus was inversely proportional to M_PEA, which was consistent with the correlation length between crosslinks estimated by X‐ray scattering measurements. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 755–764     

Synthesis of chiral iridium complexes immobilized on amphiphilic polymers and their application to asymmetric catalysis

This article details the enantioselective catalytic performance of crosslinked, polymer immobilized, Ir‐based, chiral complexes for transfer hydrogenation of cyclic imines to chiral amines. Polymerization of the achiral vinyl monomer, divinylbenzene, and a polymerizable chiral 1,2‐diamine monosulfonamide ligand followed by complexation with [IrCl₂Cp*]₂ affords the crosslinked polymeric chiral complex, which can be successfully applied to asymmetric transfer hydrogenation of cyclic imines. Polymeric catalysts prepared from amphiphilic achiral monomers have high catalytic activity in the reaction and can be used both in organic solvents and water to give chiral cyclic amines with a high level of enantioselectivity (up to 98% ee). The asymmetric reaction allows for reuse of the heterogeneous catalyst without any loss in activity or enantioselectivity over several runs. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3037–3044     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Preparation of macrodiols and polyols by chopping high‐molecular‐weight aliphatic polycarbonates

High‐molecular‐weight poly(1,4‐butylene carbonate) (PBC) (M_n: 40,000?90,000) was prepared through the condensation polymerization of dimethyl carbonate (DMC) and 1,4‐butanediol (BD) in the presence of 0.05 mol % sodium alkoxide catalyst. The subsequent feeding of 15 mol % HOAOH, such as 1,6‐hexanediol, 1,5‐pentanediol, 1,4‐cyclohexanedimethanol, or 1,4‐benzenedimethanol and stirring at 190–150 °C converted the extremely thick high‐molecular‐weight polymer to low‐molecular‐weight macrodiols with GPC‐measured M_n ～2000. The analysis of the ¹H NMR spectra indicated that the –A– units and 1,4‐butylene units were randomly distributed in the resulting oligomers. The chopping of the high‐molecular‐weight PBC using either triols or tetraols such as glycerol propoxylate, 1,1,1‐tris(hydroxymethyl)ethane, or pentaerythritol also afforded macropolyols containing branched chains with GPC‐measured M_n ～2000. When the chopped polymers were genuine PBCs, the resulting macrodiols or polyols were in a waxy state at room temperature. However, permanently oily compounds were obtained when the chopped polymers were prepared using 0.90 mole fraction of BD admixed with various other diols. The macrodiols and polyols synthesized in this study may have potential applications in the polyurethane industry. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1570–1580     

From fatty acid and lactone biobased monomers toward fully renewable polymer latexes

Novel waterborne polymeric materials based on renewable resource monomers have been prepared by the environmentally friendly miniemulsion polymerization of an oleic acid‐derivative monomer (MOA) and the α‐methylene‐γ‐butyrolactone (α‐MBL). The effect of the incorporation of different amounts of α‐MBL on kinetics and polymer microstructure is investigated. The estimation of the monomer reactivity ratios (r_α‐MBL = 0.49 and r_MOA = 1.26) shows the slight lower reactivity of the α‐MBL, resulting in a random copolymer moderately enriched with MOA at the beginning of the reaction. The thermal and mechanical properties of the polymers demonstrate that by incorporating the lactone it is possible to produce copolymers in a broad range of glass transition temperatures, with high thermal stability and improved mechanical properties. This study provides a new green route toward the bio‐sourced preparation of polymer latexes with tuneable properties, which can range from coatings to adhesives. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3543–3549     

Carbon fibers prepared from tailored reversible‐addition‐fragmentation transfer copolymerization‐derived poly(acrylonitrile)‐co‐poly(methylmethacrylate)

Reversible‐addition fragmentation‐transfer (RAFT) polymerization of acrylonitrile (AN) was performed with 2‐(2‐cyano‐2‐propyl‐dodecyl)trithiocarbonate as RAFT agent and azobis(isobutyronitrile) as initiator. Linear polyacrylonitrile (M_n = 133,000 g/mol, PDI = 1.34) was prepared within 7 h in 86% isolated yield. High‐yield copolymerization with methyl methacrylate (MMA) was performed and copolymerization parameters were determined according to Kelen and Tüdös at 90 °C in ethylene carbonate yielding r_AN = 0.2 and r_MMA = 0.42. The molecular weights, polydispersity indices (PDIs), and MMA content of the copolymer were adjusted in a way that precursor fibers could be prepared via wet spinning. These precursor fibers had round cross‐sections and a dense morphology, showing tenacities of 40–50 cN/tex and elastic moduli of 900–1000 cN/tex at a fineness of 1 dtex and an elongation of 13–17%. Precursor fibers were oxidatively stabilized and then carbonized at different temperatures. A maximum tensile strength of 2.5 GPa was reached at 1350 °C. Thermal analysis, infrared and Raman spectroscopy, wide‐angle X‐ray scattering, scanning electron microscopy, and tensile testing were used to characterize the resulting carbon fibers. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1322–1333     

Thiol‐ene and thiol‐yne‐based synthesis of glycodendrimers as nanomolar inhibitors of wheat germ agglutinin

Alkene and alkyne functional polyester‐based dendrimers of generation 1 to 4 have been prepared and reacted under free‐radical conditions with 2‐acetamido‐2‐deoxy‐1‐thio‐β‐D ‐glucose (GlcNAc‐SH). As the alkene‐dendrimers underwent the addition of one thiyl radical per ene group whereas each yne group of alkyne‐dendrimers was saturated by two thiyl radicals, a collection of glycodendrimers with glycan density ranging from six to ninety‐six GlcNAc per dendrimer was obtained. The recognition properties of the prepared glycodendrimers toward the wheat germ agglutinin (WGA) were evaluated by enzyme‐linked lectin assay (ELLA). The eight glycodendrimers were excellent ligands showing IC₅₀ values in the nanomolar range and relative potencies per sugar unit up to 2.27 e⁶ when compared to monosaccharidic GlcNAc used as monovalent reference. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2422–2433     

Effects of POSS nanoparticles on glass transition temperatures of ultrathin poly(t‐butyl acrylate) films and bulk blends

As a model system, thin films of trisilanolphenyl‐POSS (TPP) and two different number average molar mass (5 and 23 kg mol^?1) poly(t‐butyl acrylate) (PtBA) were prepared as blends by Langmuir–Blodgett film deposition. Films were characterized by ellipsometry. For comparison, bulk blends are prepared by solution casting and the samples are characterized via differential scanning calorimetry. The increase in T_g as a function of TPP content for bulk high and low molar mass samples are in the order of ～10 °C. Whereas bulk T_g shows comparable increases for both molar masses (～10 °C), the increase in surface T_g for higher molar mass PtBA is greater than for low molar mass (～22 °C vs. ～10 °C). Nonetheless, the total enhancement of T_g is complete by the time 20 wt % TPP is added without further benefit at higher nanofiller loads. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 175–182     

Tuning the LCST of poly(2‐cyclopropyl‐2‐oxazoline) via gradient copolymerization with 2‐ethyl‐2‐oxazoline

Poly(2‐propyl‐oxazoline)s can be prepared by living cationic ring‐opening polymerization of 2‐oxazolines and represent an emerging class of biocompatible polymers exhibiting a lower critical solution temperature in aqueous solution close to body temperature. However, their usability is limited by the irreversibility of the transition due to isothermal crystallization in case of poly(2‐isopropyl‐2‐oxazoline) and the rather low glass transition temperatures (T_g < 45 °C) of poly(2‐n‐propyl‐2‐oxazoline)‐based polymers. The copolymerization of 2‐cyclopropyl‐2‐oxazoline and 2‐ethyl‐2‐oxazoline presented herein yields gradient copolymers whose cloud point temperatures can be accurately tuned over a broad temperature range by simple variation of the composition. Surprisingly, all copolymers reveal lower T_gs than the corresponding homopolymers ascribed to suppression of interchain interactions. However, it is noteworthy that the copolymers still have T_gs > 45 °C, enabling convenient storage in the fridge for future biomedical formulations. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3118–3122     

Amphiphilic dendritic copolymers of tert‐butyl‐glycidylether and glycidol as a nanocontainer for an anticancer ruthenium complex

Dendritic copolymers comprising a hydrophobic core and hydrophilic shell with nearly equal numbers of hydroxyl groups in the shell and different densities in the core were prepared by a multi‐step process based on anionic ring‐opening polymerization. The diversity in the core density was obtained by using copolymer stars with poly(tert‐butyl‐glycidylether)‐block‐polyglycidol arms with nearly equal length of hydrophobic blocks and numbers of hydroxyl groups of polyglycidol but different numbers of arms as macroinitiators. The ability of the dendritic copolymers to serve as a nanocontainer for a ruthenium complex Ru(NH₃)₃Cl₃ with anticancer properties was studied. The possibility of improving the water solubility of this poorly soluble drug by loading it onto dendritic copolymers was investigated. The hydroxyl groups of the dendritic copolymers were used for complexation of the ruthenium compound to the shell. The loading efficiency was analyzed by UV–vis spectroscopy. The dendritic nanoparticles in their hydrated state were visualized using cryo‐TEM. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3488–3497     

Preparation and evaluation of a polymeric gel containing ionic liquid‐functionalized MWCNTs as a novel class of organic solvent absorbent

Multiwalled carbon nanotubes grafted with vinyl immidazolium‐based ionic liquid (MWCNT‐IL) were synthesized and utilized as a crosslinking agent for the preparation and evaluation of a polymeric gel as a new class of organic solvent absorbent. Based on our earlier organic solvent‐absorbents, the present polymeric gel exhibited high organic solvent absorbency, fast organic solvent absorption rate, and good reusability. To prepare such polymeric gel, radical polymerization was carried out with dodecyl methacrylate and butyl acrylate as comonomers, MWCNT‐ILs as crosslinking agent, and azoisobutyronitrile as initiator, providing polymeric gel in a quantitative yield. The polymeric gel synthesized under the optimized polymerization conditions absorbed 79 times the dry weight in CCl₄, 57 times in toluene, 96 in CHCl₃, and 100 times in CH₂Cl₂. The reusability of the prepared‐polymeric gel was also checked which established that the gels could be recycled and reused for at least 10 times. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3166–3172     

Well‐defined PE‐b‐PDMS diblock copolymers via the combination of thiol‐ene click and esterification reactions: Facile synthesis and compatibilization for HDPE/silicone oil blends

Well‐defined diblock copolymers of linear polyethylene (PE) and poly(dimethylsiloxane) (PDMS) have been synthesized through a facile route combining the thiol‐ene click chemistry of vinyl‐terminated polyethylene (PE‐ene) and the sequential esterification reaction. The resulting diblock copolymers are characterized by ¹H NMR, FT‐IR, DSC, TGA, and TEM. In addition, the PE‐b‐PDMS diblock copolymers have been evaluated as compatibilizers in the blends of high‐density polyethylene (HDPE) and silicone oil. The morphological analysis and mechanical properties demonstrate that the compatibilized blends with low loading concentration of PE‐b‐PDMS display significant improvements in modulus of elasticity and elongation at break as compared to the uncompatibilized binary blends. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3205–3212