N-CNTs/NiCo-LDH复合材料的制备及电化学性能

通过高温碳化聚吡咯纳米管制备了氮掺杂碳纳米管(N-CNTs), 并采用共沉淀法将镍钴层状双氢氧化物(NiCo-LDH)原位生长在N-CNTs上, 制备出具有三维互联网状结构的N-CNTs/NiCo-LDH复合材料. 研究了镍钴摩尔比对N-CNTs/NiCo-LDH复合材料形貌结构和电化学性能的影响. 结果表明, 当镍钴摩尔比为1∶2时, N-CNTs/Ni₁Co₂-LDH具有最佳的电化学性能. 在1 A/g电流密度下, 其比电容可达1311.8 F/g; 当电流密度为 10 A/g时, 电容保持率高达88.3%, 展现出优异的倍率性; 在经过2500次循环后, 电容保持率仍可达76.4%, 具有良好的循环稳定性.由N-CNTs/Ni₁Co₂-LDH与活性炭(AC)电极所构建的N-CNTs/Ni₁Co₂-LDH//AC水系混合型超级电容器, 在750 W/kg功率密度下, 具有27.19 W·h/kg的高能量密度.     

铝代α-Co（OH）2的制备及其电化学性能

采用化学共沉淀方法制备了Co-Al双金属氢氧化物,用红外光谱对所制样品的成分进行分析;用X射线衍射和场发射扫描电子显微镜表征产物的结构和形貌;用循环伏安、恒电流充放电等测试方法对Co/Al摩尔比为9∶1、8∶2和7∶3的铝代α-Co(OH)2的电化学性能进行研究。测试表明,Co/Al摩尔比为8∶2的铝代α-Co(OH)2具有最佳的电容性能,单电极比电容可达1180F/g,并且在1A/g电流密度下循环500周后,比电容仍能保持91%,有望成为电化学电容器的电极材料。     

CoxNi1-x层状双氢氧化物复合材料的制备及其超级电容器性能

通过化学共沉积方法制备了具有高比电容的介孔CoxNi1-x层状双氢氧化物(LDHs)复合材料。采用电子能谱、红外、X射线衍射、场发射扫描电镜等表征了产物的组成、结构和形貌。循环伏安、恒电流充放电等测试表明,Co0.5574Ni0.4426LDH复合材料具有最佳的电容性能,在1A/g的电流密度下,比电容高达2552F/g,且循环1000周后,比电容仍能保持90.6%,呈示该复合材料具有优异的电化学性能。     

絮状三元镍钴铁氢氧化物电极材料的制备及其电化学储能性能

采用一步溶剂热法在泡沫镍(NF)基底上合成了镍钴氢氧化物、镍铁氢氧化物及镍钴铁氢氧化物3种电极材料,并对其电化学性能进行测试,结果表明:三元镍钴铁金属电极的储能性能要远大于其他2种二元金属电极,其在2 mA·cm-2电流密度下能达到5.11 F·cm-2的面积比电容,并且构筑的非对称超级电容器在功率密度为46.814 ...     

石墨烯/钴镍双氢氧化物复合材料的制备及其超电容特性

采用氧化石墨(GO)还原法制备石墨烯(GNS),以氨水为沉淀剂,在石墨烯存在的情况下,通过Co²⁺和Ni²⁺化学共沉积的方法合成了石墨烯/钴镍双氢氧化物复合电极材料,采用红外光谱(FT-IR)、X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)、比表面积测试(BET)等技术手段表征了产物的组成、结构和形貌,用循环伏安、恒电流充放电等测试方法对复合材料的电化学性能进行了研究。 研究发现,石墨烯纳米片均匀分散在钴镍双氢氧化物中,改善了钴镍双氢氧化物的传导性和结构稳定性。 电化学测试表明,在1 A/g的电流密度下,复合材料比电容高达2770 F/g,且循环500次后,比电容仍能保持93.4%,呈示该复合材料具有优异的电化学性能。     

YF3包覆Li(Li0.22Ni0.17Mn0.61)O2正极材料的性能

富锂层状氧化物作为锂离子电池正极材料具有高比容量优势.采用草酸盐共沉淀法制备Li(Li0.22Ni0.17Mn0.61)O2,并用YF3包覆电极.采用X射线衍射(XRD)、扫描电子显微镜(SEM)和X射线能谱分析(EDS)表征材料结构、观察材料形貌.结果表明,材料颗粒尺寸在100～200 nm范围,YF3包覆不会改变材料结构和形貌.电化学恒流充放电测试表明,YF3包覆Li(Li0.22Ni0.17Mn0.61)O2电极的比容量,尤其倍率比容量明显提高.60 mA·g-1电流密度下包覆电极材料30周循环后其比容量保持在220 mAh·g-1以上,1500 mA·g-1电流密度下其比容量仍可达150 mAh·g-1.电化学阻抗谱(EIS)测试结果表明,YF3包覆电极电荷转移电阻和扩散阻抗均明显降低,有利于电化学性能改善.     

MnO_2/聚苯胺复合材料的电化学电容

以P123为模板剂,软模板法制备出纳米MnO2.酸性条件下引入苯胺并聚合,得到了MnO2/聚苯胺复合材料.X射线衍射(XRD)、红外光谱(IR),扫描电子显微镜(SEM)表征观察样品的结构、形貌.循环伏安、交流阻抗、恒电流充放电等测试MnO2/聚苯胺电极的电化学性能.结果表明:引入苯胺改变了样品纳米MnO2的形貌.MnO2/聚苯胺电极比容量高达190.8F·g-1,500次循环电极比容量仅衰减4.7%,库仑效率均保持在97%以上.     

二氧化锡/石墨烯柔性电极的制备及其在锂离子电池中的应用

采用简便的抽滤装置制备了三明治结构的不同粒径大小的二氧化锡(SnO_2)/石墨烯柔性薄膜电极,通过X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)、原子力显微镜(AFM)、比表面积(BET)和电化学等测试技术手段对样品结构、形貌和电化学性能进行表征,研究了二氧化锡颗粒大小对复合电极电化学性能的影响。结果表明,当SnO_2纳米颗粒的粒径为6 nm时柔性复合电极表现出最优的电化学性能,在100 m A/g的电流密度下经过100次循环后,可逆比容量保持在555 m A·h/g,远高于纯SnO_2和粒径过大或过小的SnO_2/石墨烯复合电极。     

α-Co(OH)_2的制备及其超级电容特性

以氯化钴为原料,聚乙烯吡咯烷酮(PVP)为分散剂,采用化学沉淀的方法制备出由纳米粒子组成的片状α-Co(OH)2.用红外光谱对所制样品的组分进行分析,用X射线衍射和场发射扫描电子显微镜表征产物的结构和形貌,用循环伏安和恒电流充放电等测试方法对其电化学性能进行研究.研究结果表明,由纳米粒子组成的片状α-Co(OH)2表现出优良的电化学性能,单电极比电容高达1220 F/g.     

交联多孔结构Mn~(2+)掺杂聚苯胺/石墨烯复合材料的制备及超级电容特性

采用简单的原位氧化聚合法成功制备了Mn2+掺杂聚苯胺/还原氧化石墨烯(Mn2+-PANI/r GO)复合物电极材料,利用傅里叶变换红外光谱、X射线衍射、扫描电镜和电化学测试等手段对其结构、形貌和电化学电容性能进行了分析研究。结果表明,纳米棒状的锰离子掺杂态聚苯胺均匀分散在褶皱的石墨烯中,形成交联状的多孔结构。当电流密度为2A/g时,电极的放电比容量高达952 F/g,循环1000次后初始比电容的保持率为86.2%。过渡金属和石墨烯的加入提高了电极材料的电化学性能,高的比电容和优良的循环稳定性使Mn2+-PANI/r GO复合物在超级电容器中有很好的应用前景。     

Enriching redox active sites by interconnected nanowalls-like nickel cobalt phospho-sulfide nanosheets for high performance supercapacitors

Although transition metal phospho-sulfides deliver outstanding electrochemical performance, complex preparation methods hindered their further development. Herein, we report a facile one-step electrodeposition approach to deposit interconnected nanowalls-like nickel cobalt phospho-sulfide (Ni-Co-P-S) nanosheets onto the surface of carbon cloth. The thin Ni-Co-P-S nanosheets with multi-components and synergetic effects delivered rich active sites, further enhancing reversible capacitance. Therefore, the as-prepared Ni-Co-P-S electrode materials exhibit excellent electrochemical performance in a three-electrode system, showcasing a high specific capacitance of 2744 F/g at 4 A/g. The full supercapacitors based on Ni-Co-P-S as positive electrode and active carbon as negative electrode showcase a high specific capacitance of 110.9 F/g at 1 A/g, impressive energy density of 39.4 Wh/kg at a power density of 797.5 W/kg in terms of excellent cycling stability (91.87% retention after 10,000 cycles). This simple electrode position strategy for synthesizing Ni-Co-P-S can be extended to prepare electrode materials for various sustainable electrochemical energy storage/conversion technologies.     

Hierarchical porous nanofibers of carbon@nickel oxide nanoparticles derived from polymer/block copolymer system

The triblock copolymer (PAA-b-PAN-b-PAA) is prepared by reversible addition-fragmentation chain-transfer polymerization, and then blended with polymer (PAN) and metal hydroxide (Ni(OH)₂) as a precursor for heat-treatment. A composite material of hierarchical porous nanofibers and nickel oxide nanoparticles (HPCF@NiO) is prepared by electrospinning combined with high-temperature carbonization. The effects of the ratio of PAA and PAA-b-PAN-b-PAA on the internal structure of nanofibers and their electrochemical properties as positive electrode materials are investigated. The experimental results show that when the ratio of PAA to PAA-b-PAN-b-PAA is 1.3 to 0.4, it has good pore structure and excellent electrochemical performance. At the current density of 1 A/g, the specific capacitance is 188.7 F/g and the potential window is −1 V to 0.37 V. The asymmetric supercapacitor assembled with activated carbon as the negative electrode materials has a specific capacitance of 21.2 F/g in 2 mol/L KOH and a capacitance retention of 85.7% after 12,500 cycles at different current density.     

Porous cobalt hydroxide film electrodeposited on nickel foam with excellent electrochemical capacitive behavior

A new porous cobalt hydroxide film has been successfully electrodeposited on nickel foam from 0.1?M cobalt nitrate electrolyte at ?1.0?V vs. SCE without adding any surfactant. The microstructure and surface morphology of prepared cobalt hydroxide films were physically characterized by X-ray diffraction analysis and scanning electron microscopy. The results indicate that an interlaced network structure was obtained. The effects of electrodeposition time, deposition potential, and different substrates on the specific capacitance and microstructure of prepared porous ??-Co(OH)₂ thin film were systematically studied. The results indicate that the film deposited on nickel foam at ?1.0?V has excellent electrochemical properties. A maximum specific capacitance of 1473?F?g^?1 could be achieved at a current density of 2?A?g^?1.     

纳米多孔结构镍基复合膜电极的电化学法制备及其电容特性

通过对电沉积法得到的Ni-Cu合金镀层进行电化学去合金化处理, 制备了纳米多孔结构金属镍膜. 采用循环伏安法对多孔金属镍膜在1 mol·L^-1 KOH溶液中进行阳极氧化处理, 获得了纳米多孔结构的镍基复合膜电极. 应用扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和电化学技术对所制备的膜电极的物理性质及赝电容特性进行了表征. SEM、XRD和XPS的测试结果表明, 所制备的纳米多孔结构镍基复合膜由Ni、Ni(OH)₂和NiOOH组成. 电化学实验结果显示, 该复合膜在20 A·g^-1的充放电电流密度下, 给出了578 F·g^-1的初始比电容; 在1000次充放电循环后, 它的比电容值为544 F·g^-1, 电容保持率为94%. 纳米多孔结构有利于KOH电解液的渗透, 从而促进反应物种在电极内部的传输; 纳米多孔的金属镍基体可以提高Ni(OH)₂膜的电子导电性; 纳米大小的Ni(OH)₂颗粒能够缩短质子的固相扩散路径. 上述因素是所制备的纳米多孔结构镍基复合膜电极具有优异赝电容特性的主要原因.     

Facile synthesis of high electrical conductive CoP via solid-state synthetic routes for supercapacitors

Co-P precursor was prepared by a mechanical alloying method and then is controlled to synthesis of Co P phase through an annealing method. The optimal conditions of ball milling and annealing temperature are investigated. The Co P exhibits higher electrical conductivity than graphite and cobalt oxide, showing excellent pseudocapacitive properties due its high electrical conductivity which can result in a fast electron transfer in high rate charge–discharge possess. The as-obtained Co P electrode achieves a high specific capacitance of 447.5 F/g at 1 A/g, and displays an excellent rate capability as well as good cycling stability. Besides, the asymmetric supercapacitor(ASC) based on the Co P as the positive electrode and activated carbon(AC) as the negative electrode was assembled and displayed a high rate capability(60%of the capacitance is retained when the current density increased from 1 A/g to 12 A/g), excellent cycling stability(96.7% of the initial capacitance is retained after 5000 cycles), and a superior specific energy of19 Wh/kg at a power density of 350.8 W/kg. The results suggest that the Co P electrode materials have a great potential for developing high-performance electrochemical energy storage devices.     

双金属离子调控型镍钴氧化物纳米片用于非对称超级电容器

通过水热-煅烧两步法制备了系列镍钴氧化物(NCO)纳米片。通过改变前驱体溶液中的镍、钴离子物质的量之比，进而调控NCO纳米片中的过渡金属离子比例。NCO纳米片的晶相、形貌和结构利用X射线衍射、扫描电子显微镜和X射线光电子能谱表征。此外，对NCO纳米片的电化学性能进行测试。结果表明，NCO-2(Ni_1.95Co₁O_x)纳米片在0.5 A·g^-1电流密度下，比电容为1 096.88 F·g^-1，且经过5 000次循环后具有78.26%的循环稳定性。以NCO-2为正极、活性碳为负极构成的非对称超级电容器，在功率密度为576 W·kg^-1时，能量密度为57.70 Wh·kg^-1。     

双金属离子调控型镍钴氧化物纳米片用于非对称超级电容器

通过水热-煅烧两步法制备了系列镍钴氧化物（NCO）纳米片。通过改变前驱体溶液中的镍、钴离子物质的量之比,进而调控NCO纳米片中的过渡金属离子比例。NCO纳米片的晶相、形貌和结构利用X射线衍射、扫描电子显微镜和X射线光电子能谱表征。此外,对NCO纳米片的电化学性能进行测试。结果表明,NCO-2（Ni_1.95Co₁O_x）纳米片在0.5 A·g^-1电流密度下,比电容为1 096.88 F·g^-1,且经过5 000次循环后具有78.26%的循环稳定性。以NCO-2为正极、活性碳为负极构成的非对称超级电容器,在功率密度为576 W·kg^-1时,能量密度为57.70 Wh·kg^-1。     

Ni–Al composite hydroxides fabricated by cation–anion double hydrolysis method for high-performance supercapacitor

Chemical doping of nickel hydroxide with other cations(e.g. Al~(3+)) is an efficient way to enhance its electrochemical capacitive performances. Herein, a simple cation–anion(Ni~(2+)and AlO_2) double hydrolysis method was developed toward the synthesis of nickel–aluminum(Ni–Al) composite hydroxides. The obtained composite hydroxides possesses a porous structure, large surface area(121 m~2/g) and homogeneous element distribution. The electrochemical test shows that the obtained composite hydroxides exhibits a superior supercapacitive performances(specific capacitance of 1670F/g and rate capability of 87% from 0.5 A/g to 20 A/g) to doping-free nickel hydroxide(specific capacitance of 1227 F/g and rate capability of 47% from 0.5 A/g to 20 A/g). Moreover, the galvanostatic charge/discharge test displays that after 2000 cycles at large current density of 10 A/g, the composite hydroxides achieves a high capacitance retention of 98%, indicative of an excellent electrochemical cycleability.