二氧化钛与碳纳米管协同作用的葡萄糖生物传感研究

在玻碳电极表面滴涂二氧化钛纳米颗粒-碳纳米管-壳聚糖(TiO2-MWNT-CS)复合物,待干后在其TiO2-MWNT-CS修饰电极表面电沉积一层均匀而致密的纳米铂(Pt),然后将葡萄糖氧化酶(GOD)固定于修饰电极表面,最后,为了防止酶的泄漏和干扰物质的干扰,将Nafion滴涂于修饰电极表面,制得新型的葡萄糖传感器。通过循环伏安法,交流阻抗技术和计时电流法考察了电极的电化学特性。在最佳的实验条件下,该传感器在3.0×10-6～1.45×10-3 mol/L范围内对葡萄糖有良好的线性响应,相关系数为0.9967(n=15),检测下限为9.5×10-7 mol/L(S/N=3)。由于纳米粒子间的协同作用,该传感器具有灵敏度高、稳定性和选择性好等优点。     

天青Ⅰ修饰玻碳电极的电化学性质及其对NADH的催化氧化

本文利用滴涂于玻碳表面的Nafion膜中负电性的磺酸基与天青I阳离子之间的静电作用,以实现天青I的固定化,从而制备出Nafion/天青I电催化型烟酰胺腺嘌呤二核苷酸(NADH)传感器。采用循环伏安法考察了传感器的电化学性质,并研究了该修饰电极对NADH的电催化作用。实验结果表明:该修饰电极对NADH有良好的电催化作用,NADH氧化峰电位比未修饰的玻碳电极负移了660 mV,响应电流与NADH的浓度在8.7×10-5~1.5×10-2mol/L范围内呈良好的线性关系。该方法检出限为3.0×10-5mol/L。     

基于纳米MnO2-MWCNTs复合材料修饰的葡萄糖传感器

采用水热法制备了纳米MnO2,并用红外光谱,X射线衍射(XRD)和扫描电子显微镜(SEM)对其进行了表征。将碳纳米管和纳米MnO2分散在壳聚糖溶液中,用滴涂法固定到玻碳电极表面,制成修饰电极。利用计时电流法对该葡萄糖传感器的性能进行了研究,纳米MnO2-MWCNTs复合物对葡萄糖的氧化有明显的催化作用。在优化的条件下,葡萄糖在5.0×10-5～3.0×10-2mol/L浓度范围内,计时电流与浓度之间呈线性关系,检出限为1.5×10-5 mol/L(S/N=3)。对1.0×10-3 mol/L葡萄糖溶液平行测定8次的相对标准偏差(RSD)为2.1%。该传感器可成功用于葡萄糖注射液中葡萄糖的测定,回收率在96.4%～98.6%之间。     

纸基葡萄糖电化学生物传感器的研究及应用

基于纳米金的自催化无电沉积镀金技术,采用混合纤维素滤膜作为模板,制备了一种纳米多孔纸基薄膜金电极。以该金滤膜电极作为基底电极,使用Nafion溶液分散的碳纳米管-纳米铂(PtNPs)复合材料作为载体,实现了葡萄糖氧化酶(GOD)的直接电化学,并建立了一种低成本的纸基葡萄糖电化学传感器。该传感器对葡萄糖具有良好的安培响应,葡萄糖浓度在5.0×10-6~2.5×10-3 mol/L范围与其0.55V处的氧化电流呈良好的线性关系(R=0.999),检测限(S/N=3)为1.0×10-6 mol/L。制备了8支传感器,对25μmol/L葡萄糖进行检测,结果的相对标准偏差为6.03%,表明该传感器具有较好的重现性。     

电沉积法制备铁氰化铈/Nafion复合物纳米颗粒及其对多巴胺电催化氧化性能的研究

采用电沉积法沉积铁氰化铈(CeHCF)纳米颗粒,在Nafion修饰的玻碳电极表面电沉积致密的、分散性良好的铁氰化铈纳米粒子。用场发射扫描电子显微镜(FE-SEM)对铁氰化铈纳米颗粒的形貌进行了表征。利用循环伏安法(CV)研究了多巴胺在铁氰化铈/Nafion修饰玻碳电极(CeHCF/NF/GCE)表面上的电化学行为。研究表明,CeHCF/NF/GCE对多巴胺具有良好的电催化氧化作用,该传感器对多巴胺在一定浓度下呈良好的线性关系,其线性范围是1.0×10~(-7)~3.4×10~(-4)mol/L。检测限为0.2×10~(-7)mol/L(S/N=3)。     

葡萄糖氧化酶在石墨烯-纳米氧化锌修饰玻碳电极上的直接电化学及对葡萄糖的生物传感

采用滴涂法和电沉积法制备了石墨烯/纳米氧化锌复合膜修饰玻碳电极,再将葡萄糖氧化酶固定在修饰电极表面制成了电化学生物传感器,用于葡萄糖的灵敏测定。用循环伏安法在-0.7～-0.1 V范围内研究了葡萄糖氧化酶在修饰电极上的直接电化学行为。结果表明,石墨烯/纳米氧化锌复合膜能很好地保持葡萄糖氧化酶的生物活性,并显著促进了其电化学过程。在0.1 mol/L磷酸盐缓冲溶液(pH 7.0)中,固定在修饰电极上的葡萄糖氧化酶呈现出一对近乎可逆的氧化还原峰,并且对葡萄糖的氧化具有良好的催化作用。葡萄糖氧化酶在修饰电极上的电子转移常数ks为1.42 s-1,修饰电极对葡萄糖催化的米氏常数Kampp为14.2μmol/L。线性范围为2.5×10-6～1.5×10-3mol/L,检出限为2.4×10-7mol/L(S/N=3)。此修饰电极具有良好的导电性能、稳定性和重现性,可用于实际样品的分析测定。     

葡萄糖氧化酶在纳米金/壳聚糖/离子液体BMIMPF6修饰电极上的直接电化学及其应用

用滴涂法将葡萄糖氧化酶(GOD)修饰到纳米金(Nano-Au)/壳聚糖(CS)/1-丁基-3-甲基咪唑六氟磷酸盐(BMIMPF6)复合材料修饰的金电极表面,制备了GODNano-Au/CS/BMIMPF6/Au生物传感器。采用循环伏安法(CV)和扫描电子显微镜(SEM)对该生物传感器进行表征,并对其制备条件、电化学性质进行了较为详细的研究。结果表明,复合材料不仅为GOD提供了良好的微环境,而且通过纳米尺寸效应和离子液体的高导电性,促进电子转移,使GOD具有更高的活性。该修饰电极可作为葡萄糖生物传感器,在最优条件下,葡萄糖浓度在1.0×10-4~1.0×10-6 mol·L-1范围内呈良好的线性关系,其线性相关系数r=0.9995,检出限为3.85×10-8 mol·L-1。     

层层自组装纳米金与乙酰胆碱酯酶电化学生物传感器检测有机磷农药

采用层层自组装技术制备了快速检测有机磷农药的生物传感器,利用带正电荷的高分子聚电解质聚二烯丙基二甲基氯化铵(PDDA)将乙酰胆碱酯酶(AChE)和金纳米粒子(AuNPs)通过静电力逐层固定到玻碳电极(GCE)表面,并采用交流阻抗和微分脉冲伏安法研究了此生物传感器的电化学行为。由于金纳米粒子优异的电催化性能和良好的生物相容性,使固定化的乙酰胆碱酯酶对其底物具有更高的亲和力和更快的响应速度。实验结果表明:修饰金纳米粒子后,传感器的氧化电流明显增大,在4.6×10-5～5.3×10-3mol/L范围内,固定化酶的抑制率与甲基对硫磷浓度的对数成正比,检出限为7.6×10-6mol/L。该生物传感器具有制备方法简便、成本低、灵敏度高等优点,已成功用于蔬菜样品中甲基对硫磷含量的测定。     

基于CuO-NiO复合氧化物的无酶葡萄糖传感器

通过化学共沉淀法制备了CuO-NiO复合氧化物。在最优条件下,该复合物修饰玻碳电极对葡萄糖检测的线性范围为2×10-6~4.1×10-3mol/L;灵敏度为4116μA·L·mmol-1·cm-2;检测限为0.2μmol/L(S/N=3)。传感器可用于葡萄糖检测。     

棒状Sb2S3-nafion纳米复合膜修饰玻碳电极的大肠杆菌DNA传感器

将棒状Sb2S3纳米粒子与Nafion聚合物在乙醇溶液中超声混合得到均匀的Sb2S3-Nafion纳米复合材料分散液。将该复合材料滴涂至玻碳电极(GCE)表面,得到稳定的Sb2S3-Nafion修饰电极。循环伏安和阻抗表征实验表明,由于Sb2S3的纳米尺寸效应及半导体效应,电极的电化学性能得到了极大的提高。采用PCl5为活化剂,将Nafion表面的磺酸基团酰氯化,再利用共价键合法将末端修饰氨基的大肠杆菌DNA特征序列固定到修饰电极表面,制备了一种新型的DNA电化学传感器。以亚甲基蓝(MB)为杂交指示剂,将制备的DNA电化学传感器应用于大肠杆菌基因目标序列检测,结果表明,该传感器对目标DNA具有较宽的动力学线性范围(1.0×10-12～1.0×10-7mol/L),检出限达到2.4×10-13mol/L。此外,选择性实验表明该传感器对互补序列、单碱基错配序列、三碱基错配序列和完全错配序列具有良好的识别能力。     

微过氧化物酶-11修饰电极对O2和H2O2的电催化还原

运用电化学循环伏安法和旋转圆盘电极技术研究了Ｏ２和Ｈ２Ｏ２在Ｎａｆｉｏｎ膜固定的微过氧化物酶－１１修饰的玻磷（ＭＰ－１１＋Ｍａｆｉｏｎ／Ｇｃ）电极上的电化学还原,结果表明,饰电极 对Ｏ２和Ｈ２Ｏ２的还原均具电催化作用。测定和比较了Ｏ２和Ｈ２Ｏ２在ＭＰ－１１＋Ｎａｆｉｏｎ／ＧＣ的电极上电催化还原反应的一些动力学参数。发现Ｏ２在修饰电极上经历了四电子还原,且还原过程与溶液的ＰＨ值有关。     

ZnO-MWCNTs/Nafion Inorganic-organic composite film： Preparation and application in bioelectrochemistry of hemoglobin

Multi-walled carbon nanotubes(MWCNTs) were coated with ZnO by a hydrothermal method.The resulting nanocomposites were mixed with the Nafion solution to form a composite matrix for the fabrication of hemoglobin(Hb) biosensor.To prevent the leak of Hb molecules of the biosensor,silica sol-gel film was coated on the surface of the Hb/ZnO-MWCNTs/Nafion electrode.The silica sol-gel/Hb/ZnO-MWCNTs/Nafion film exhibited a pair of well-defined,quasi-reversible redox peaks.This biosensor showed excellent electroca...     

基于聚亚甲基蓝-碳纳米管复合膜固载血红蛋白的H2O2生物传感器

采用吸附和电化学聚合修饰方法,制得了聚亚甲基蓝-碳纳米管聚合膜玻碳电极(PMB-MWNTs/GCE),再将血红蛋白(Hb)固定在PMB-MwNTs/GCE表面,制备了稳定的Hb/PMB-MwNTs//GCE的H2O2生物传感器,并用循环伏安法对修饰电极的生物电催化行为进行了表征.研究结果表明,固定在PMB-MWNTs/...     

Amperometric phenol biosensor based on sol-gel silicate/Nafion composite film

An amperometric biosensor based on tyrosinase immobilized in silicate/Nafion composite film has been developed for the determination of phenolic compounds. The Nafion polymer in the composite was used not only to overcome the brittleness of the pure sol-gel-derived silicate film but also to increase the long-term stability of the biosensor. Tyrosinase was immobilized by a thin film of silicate/Nafion composite on a glassy carbon electrode. Phenolic compounds were determined by the direct reduction of biocatalytically-liberated quinone species at −200 mV versus Ag/AgCl (3 M NaCl). The process parameters for the fabrication of the enzyme electrode and various experimental variables such as pH and operating potential were explored for optimum analytical performance of the enzyme electrode. The biosensor can reach 95% of steady-state current in about 15 s. The sensitivities of the biosensor for catechol and phenol were 200 and 46 mA/M, respectively. A detection limit of 0.35 mM catechol was obtained with a signal-to-noise ratio of 3. The enzyme electrode retained 74% of its initial activity after 2 weeks of storage in 50 mM phosphate buffer at pH 7.     

肌红蛋白在Nafion/Fe3O4- CdTe/CdS量子点复合膜内的直接电化学及其应用于H2O2的生物传感

利用磁性纳米Fe3O4和CdTe/CdS量子点结合Nafion的良好成膜性,将肌红蛋白(Mb)固定在玻碳 电极表面制备成Nafion/Fe3O4 - CdTe/CdS - Mb/GCE修饰电极.在pH 7.0的0.1 mol/L磷酸盐缓冲溶液 (PBS)中,固定在膜内的Mb表现出良好的直接电化学性质,在-0.351...     

血红蛋白在壳聚糖修饰碳纳米管上的电化学特性及对过氧化氢的电催化分析

用壳聚糖对多壁碳纳米管进行修饰,构建了一种用于固定血红蛋白的新型复合材料,并研究了血红蛋白在该碳纳米管上的电化学性质及其对过氧化氢的电催化活性.扫描电镜结果表明,壳聚糖修饰的多壁碳纳米管呈单一的纳米管状,并能均匀分散在玻碳电极表面.紫外光谱分析表明血红蛋白在该复合膜内能很好地保持其原有的二级结构.将该材料固定在玻碳电极上后,血红蛋白能成功地实现其直接电化学.根据峰电位差随着扫描的变化,计算得到血红蛋白在壳聚糖修饰的碳纳米管膜上的电荷转移系数为0.57,表观电子转移速率常数为7.02 s-1.同时,该电极对过氧化氢显示出良好的催化性能,电流响应信号与H2O2浓度在1.0×10-6 ～1.5×10-3 mol/L间呈线性关系,检出限为5.0×10-7 mol/L.修饰电极显示了良好的稳定性.     

Amperometric Ethanol Biosensor Based on Carbon Nanotubes Dispersed in Sol–Gel‐Derived Titania–Nafion Composite Film

Composite solution of sol–gel‐derived titania and perfluorosulfonated ionomer (Nafion) was used as a solubilizing agent for multiwalled carbon nanotubes (CNT) as well as an encapsulation matrix for alcohol dehydrogenase (ADH) for the fabrication of a highly sensitive and stable amperometric ethanol biosensor. ADH was immobilized within a thin film of CNT–titania–Nafion composite film coated on a glassy carbon electrode. Because of the mesoporous nature of the CNT–titania–Nafion composite film, the present biosensor exhibited remarkably fast response time within 2 s. The presence of CNT in the composite film increases not only the sensitivity of the ethanol biosensor but also the long‐term stability of the biosensor. The present biosensor responds linearly to ethanol in the wide concentration ranges from 1.0×10^?5 M to 3.0×10^?3 M with the sensitivity of 51.6 mA M^?1cm^?2. The present biosensor showed good long‐term stability with 75% of its activity retained after 4 weeks of storage in 50 mM phosphate buffer at pH 7.0.     

基于Hemin/多壁碳纳米管纳米复合物构建的过氧化氢生物传感器的研究

利用卟啉(Hemin)具有模拟酶的功能,与多壁碳纳米管(MWCNTs)构建了一种新型的过氧化氢(H2O2)生物传感器。首先,利用Hemin与MWCNTs之间的π-π键作用,在超声分散下制备Hemin/MWCNTs纳米复合物;采用滴涂技术并在nafion的作用下将其固载在电极表面,制得该H2O2生物传感器(nafion/Hemin/MWCNTs/GCE)。采用紫外-可见分光光度法(UV-Vis)对合成的纳米复合物进行了分析;采用扫描电镜(SEM)对电极的表面形貌进行了表征;采用循环伏安法和计时电流法考察了该修饰电极的电化学行为;并对传感器的行为进行了详细的研究。在最优条件下,此修饰电极对H2O2具有明显的催化作用,电流与H2O2的浓度在6.0×10-7~1.8×10-3 mol/L范围内呈现良好的线性关系,检出限达2.0×10-7 mol/L。此传感器制作简单,具有较高的灵敏度和良好的稳定性及重现性。     

Direct Electrochemistry of Myoglobin in a Nafion‐Ionic Liquid Composite Film Modified Carbon Ionic Liquid Electrode

In this paper two kinds of ionic liquids (ILs) were used for the construction of a myoglobin (Mb) electrochemical biosensor. Firstly a hydrophilic ionic liquid of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIMBF₄) was used as binder to prepare a carbon ionic liquid electrode (CILE), then a Nafion and hydrophobic ionic liquid of 1‐butyl‐3‐methylimidazolium hexafluorophosphate (BMIMPF₆) composite film was applied on the surface of the CILE. The direct electrochemistry of Mb in the Nafion‐BMIMPF₆/CILE was achieved with the cathodic and anodic peak potentials located at ?0.345 V and ?0.213 V (vs. SCE). The formal potential (E°′) was located at ?0.279 V, which was the characteristic of Mb Fe^III/Fe^II redox couples. The electrochemical behaviors of Mb in the Nafion‐ionic liquid composite film modified CILE were carefully investigated. The Mb modified electrode showed good electrocatalytic behaviors to the reduction of trichloroacetic acid (TCA) and NaNO₂. Based on the Nafion‐BMIMPF₆/Mb/CILE, a new third generation reagentless biosensor was constructed.     

Direct electrochemistry of glucose oxidase on the hydroxyapatite/Nafion composite film modified electrode and its application for glucose biosensing

A novel glucose biosensor was constructed by immobilizing the glucose oxidase (GOD) on a hydroxyapatite (HAp)/Nafion composite film modified glassy carbon electrode (GCE) and applied to the highly selective and sensitive determination of glucose. With the cooperation of HAp and Nafion, the composite film played an important role in enhancing the stability and sensitivity of the biosensor. The results demonstrate that the GOD adsorbed onto the HAp/Nafion composite film exhibits a pair of well-defined nearly reversible redox peaks and fine catalysis to the oxidation of glucose companied with the consumption of dissolved oxygen. On the basis of the decrease of the reduction current of dissolved oxygen at the applied potential of −0.80 V (vs. SCE) upon the addition of glucose, the concentration of glucose could be detected sensitively and selectively. The decreased reduction current was linear with the concentration of glucose in the range of 0.12–2.16 mM. The detection limit and sensitivity were 0.02 mM (S/N = 3) and 6.75 mA·M⁻¹, respectively. All the results demonstrate that HAp/Nafion composite film provides a novel and efficient platform for the immobilization of enzymes and realizes the direct electrochemistry. The composite materials should have potential applications in the fabrication of third-generation biosensors.