Wingtip vortex control via the use of a reverse half-delta wing

The effect of a 65° sweep reverse half-delta wing (RHDW), mounted at the squared tip of a rectangular NACA 0012 wing, on the tip vortex was investigated experimentally at Re?=?2.45?×?10⁵. The RHDW was found to produce a weaker tip vortex with a lower vorticity level and, more importantly, a reduced lift-induced drag compared to the baseline wing. In addition to the lift increment, the RHDW also produced a large separated wake flow and subsequently an increased profile drag. The reduction in lift-induced drag, however, outperformed the increase in profile drag and resulted in a virtually unchanged total drag in comparison with the baseline wing. Physical mechanisms responsible for the RHDW-induced appealing aerodynamics and vortex flow modifications were discussed.     

Near-field tip vortex behind a swept wing model

The near-field flow structure of a tip vortex behind a sweptback and tapered NACA 0015 wing was investigated and compared with a rectangular wing at the same lift force and Re=1.81×10⁵. The tangential velocity decreased with the downstream distance while increased with the airfoil incidence. The core radius was about 3% of the root chord c _r, regardless of the downstream distance and α for α<8°. The core axial velocity was always wake-like. The core Γ_c and total Γ_o circulation of the tip vortex remained nearly constant up to x/c _r=3.5 and had a Γ_c/Γ_o ratio of 0.63. The total circulation of the tip vortex accounted for only about 40% of the bound root circulation Γ_b. For a rectangular wing, the axial flow exhibited islands of wake- and jet-like velocity distributions with Γ_c/Γ_o=0.75 and Γ_o/Γ_b=0.70. For the sweptback and tapered wing tested, the inner region of the tip vortex flow exhibited a self-similar behavior for x/c _r≥1.0. The lift force computed from the spanwise circulation distributions agreed well with the force-balance data. A large difference in the lift-induced drag was, however, observed between the wake integral method and the inviscid lifting-line theory.     

Experimental investigation on tip vortices and aerodynamics

The tip vortices and aerodynamics of a NACA0012 wing in the vicinity of the ground were studied in a wind tunnel. The wing tip vortex structures and lift/drag forces were measured by a seven-hole probe and a force balance, respectively. The evolution of the flow structures and aerodynamics with a ground height were analyzed. The vorticity of tip vortices was found to reduce with the decreasing of the ground height, and the position of vortex-core moved gradually to the outboard of the wing tip. Therefore, the down-wash flow induced by the tip vortices was weakened. However, vortex breakdown occurred as the wing lowered to the ground. From the experimental results of aerodynamics, the maximum lift-to-drag ratio was observed when the angle of attack was 2.5° and the ground clearance was 0.2.     

Lift-induced drag of a cambered wing for Re ≤ 1 × 106

An investigation of the dependence of the lift-induced drag coefficient C _Di of a square-tipped, cambered wing model on Reynolds number for Re ≤ 1 × 10⁶ was conducted. Computed based on the vorticity distribution inferred from the near-field cross-flow velocity measurements of the tip vortex, different C _Di prediction schemes were used. The effect of measurement plane size and grid resolution on the C _Di calculations was also identified. The C _Di estimated by the integral method was found to increase with increasing Re and was below the C _Di = C _l²/πeAR prediction. Limits on the measurement plane size and grid resolution were determined to be at least 40% larger than the vortex outside diameter and no larger than 0.63% chord, respectively, in order to provide a good estimate of the induced drag.     

Effect of apex strake incidence-angle on the vortex development and interaction of a double-delta wing

The vortex flow characteristics of a sharp-edged delta wing with an apex strake was investigated through the visualization and particle image velocimetry (PIV) measurement of the wing-leeward flow region, and the wing-surface pressure measurement. The wing model was a flat-plate, and 65°-sweep cropped-delta wing with sharp leading edges. The apex strake was also a flat-plate wing with a cropped-delta shape of 65°/90° sweep, and it can change its incidence angle. The flow Reynolds number was 2.2 × 10⁵ for the flow visualization and 8.2 × 10⁵ for the PIV and wing-surface pressure measurements. The physics of the vortex flow in the wing-leeward flow region and the suction-pressure distribution on the wing upper-surface were interrelated and analyzed. The effect of a positive (negative) strake incidence-angle was the upward movement of the strake and wing vortices away from (downward movement of the strake and wing vortices toward) the wing-upper surface and the delayed (enhanced) coiling interaction between them. This change of vortex flow characteristics projected directly on the suction pressure distribution on the wing upper-surface.     

Effects of a trapped vortex cell on a thick wing airfoil

The effects of a trapped vortex cell (TVC) on the aerodynamic performance of a NACA0024 wing model were investigated experimentally at Re = 10⁶ and 6.67×10⁵6.67\times 10^{5}. The static pressure distributions around the model and the wake velocity profiles were measured to obtain lift and drag coefficients, for both the clean airfoil and the controlled configurations. Suction was applied in the cavity region to stabilize the trapped vortex. For comparison, a classical boundary layer suction configuration was also tested. The drag coefficient curve of the TVC-controlled airfoil showed sharp discontinuities and bifurcative behavior, generating two drag modes. A strong influence of the angle of attack, the suction rate and the Reynolds number on the drag coefficient was observed. With respect to the clean airfoil, the control led to a drag reduction only if the suction was high enough. Compared to the classical boundary layer suction configuration, the drag reduction was higher for the same amount of suction only in a specific range of incidence, i.e., α = −2° to α = 6° and only for the higher Reynolds number. For all the other conditions, the classical boundary layer suction configuration gave better drag performances. Moderate increments of lift were observed for the TVC-controlled airfoil at low incidence, while a 20% lift enhancement was observed in the stall region with respect to the baseline. However, the same lift increments were also observed for the classical boundary layer suction configuration. Pressure fluctuation measurements in the cavity region suggested a very complex interaction of several flow features. The two drag modes were characterized by typical unsteady phenomena observed in rectangular cavity flows, namely the shear layer mode and the wake mode.     

PIV study of near-field tip vortex behind perforated Gurney flaps

The impact of Gurney flaps, of different heights and perforations, on the growth and development of a tip vortex, both along the tip and in the near field of a finite NACA 0012 wing, at Re = 1.05 × 10⁵ was investigated by using particle image velocimetry (PIV). Wind-tunnel force balance measurements were also made to supplement the PIV results. This study is a continuation of the work of Lee and Ko (Exp Fluids 46(6):1005–1019, 2009) on the near-wake measurements behind perforated Gurney flaps. The present results show that along the tip, the overall behavior of the secondary vortices and their interaction with the primary, or tip, vortex remained basically unchanged, regardless of flap height and perforation. The peak vorticity of the tip vortex, however, increased with flap height and always exhibited a local maximum at x/c = 0.8 (from the leading edge). In the near field, the strength and structure of the near-field tip vortex were found to vary greatly with the flap height and perforation. The small flaps produced a more concentrated tip vortex with an increased circulation, while the large Gurney flaps caused a disruption of the tip vortex. The disrupted vortex can, however, be re-established by the addition of flap perforation. The larger the flap perforation the more organized the tip vortex. The Gurney flaps have the potential to serve as an alternative off-design wake vortex control device.     

Investigation of turbulence structures in a drag-reduced turbulent channel flow with surfactant additive by stereoscopic particle image velocimetry

In the present study, we employed stereoscopic particle image velocimetry (PIV) to investigate the characteristics of turbulence structures in a drag-reduced turbulent channel flow with addition of surfactant. The tested drag-reducing fluid was a CTAC/NaSal/Water (CTAC: cetyltrimethyl ammonium chloride; NaSal: sodium salicylate) system at 25°C. The weight concentration of CTAC was 30 ppm. Stereoscopic PIV measurement was performed for a water flow (Re=1.1×10⁴) and a CTAC solution flow (Re=1.5×10⁴ with 54% drag reduction) in both the streamwise–spanwise and wall-normal-spanwise planes, respectively. The three-dimensionality of hairpin vortex structures in the near-wall region for wall-bounded turbulent flow was reproduced by conditionally averaging the stereoscopic two-dimensional-three-component velocity fields. A series of wall-normal vortex cores were found to align with the near-wall low-speed streaks with opposite vorticity signals at both sides of the streaks and with the vorticity decreased on average by about one order of magnitude in CTAC solution flow compared with water flow; the spanwise spacing between the near-wall low-speed streaks in the solution flow is increased by about 46%. The streamwise vorticity of the vortex cores appearing in the wall-normal-spanwise plane was also decreased by the use of drag-reducing surfactant additives.     

Reduction of the Induced Drag of a Supersonic Wing

The oblique wing effect, i.e., a reduction in the wave drag for given lift, cannot be realized for a delta wing with supersonic leading edges owing to the lift reduction in the wing mid-section. To preserve the effect, the disturbances generated by the delta wing vertex must be eliminated by adding a body (wedge) to the wing by replacing the streamsurfaces behind the shock with rigid surfaces. Moreover, using wing tip deflection, and thereby reducing the wave drag to zero, makes it possible to obtain a lift- drag ratio close to that of the limiting, infinitely long flat plate.     

Impact of short-span strip on oscillating-wing tip vortex

The impact of 12 spoiler–tab configurations, of different heights and widths, on the tip vortex generated by an oscillating NACA 0015 wing was investigated experimentally. For an oscillating wing equipped with a spoiler, the peak tangential velocity and core and total circulation were greatly reduced compared to a tab, regardless of its width, while the core radius remained largely unaffected with its center displaced vertically above the baseline wing. The most noticeable impact of a spoiler with a reduced height was its potential in alleviating the blade–vortex interaction (BVI) strength. Meanwhile, the largest favorable impact on the critical vortex flow parameters was achieved via a 25%-span spoiler–tab combination with a height of 5 and 2.5% chord, respectively. A contrary effect on the BVI suppression, especially during pitch-up, was, however, observed. The impact on the BVI can be improved by reducing the height of the spoiler at the expense of unfavorable change in the vortex strength and displacement.     

The influence of the wake of a flapping wing on the production of aerodynamic forces

The effect of the wake of previous strokes on the aerodynamic forces of a flapping model insect wing is studied using the method of computational fluid dynamics. The wake effect is isolated by comparing the forces and flows of the starting stroke (when the wake has not developed) with those of a later stroke (when the wake has developed). The following has been shown. (1) The wake effect may increase or decrease the lift and drag at the beginning of a half-stroke (downstroke or upstroke), depending on the wing kinematics at stroke reversal. The reason for this is that at the beginning of the half-stroke, the wing ``impinges' on the spanwise vorticity generated by the wing during stroke reversal and the distribution of the vorticity is sensitive to the wing kinematics at stroke reversal. (2) The wake effect decreases the lift and increases the drag in the rest part of the half-stroke. This is because the wing moves in a downwash field induced by previous half-stroke's starting vortex, tip vortices and attached leading edge vortex (these vortices form a downwash producing vortex ring). (3) The wake effect decreases the mean lift by 6%–18% (depending on wing kinematics at stroke reversal) and slightly increases the mean drag. Therefore, it is detrimental to the aerodynamic performance of the flapping wing. The project supported by the National Natural Science Foundation of China (10232010) and the National Aeronautic Science Fund of China(03A51049) The English text was polished by Xing Zhang     

Large aerodynamic forces on a sweeping wing at low Reynolds number

The aerodynamic forces and flow structure of a model insect wing is studied by solving the Navier-Stokes equations numerically. After an initial start from rest, the wing is made to execute an azimuthal rotation (sweeping) at a large angle of attack and constant angular velocity. The Reynolds number (Re) considered in the present note is 480 (Re is based on the mean chord length of the wing and the speed at 60% wing length from the wing root). During the constant-speed sweeping motion, the stall is absent and large and approximately constant lift and drag coefficients can be maintained. The mechanism for the absence of the stall or the maintenance of large aerodynamic force coefficients is as follows. Soon after the initial start, a vortex ring, which consists of the leading-edge vortex (LEV), the starting vortex, and the two wing-tip vortices, is formed in the wake of the wing. During the subsequent motion of the wing, a base-to-tip spanwise flow converts the vorticity in the LEV to the wing tip and the LEV keeps an approximately constant strength. This prevents the LEV from shedding. As a result, the size of the vortex ring increases approximately linearly with time, resulting in an approximately constant time rate of the first moment of vorticity, or approximately constant lift and drag coefficients. The variation of the relative velocity along the wing span causes a pressure gradient along the wingspan. The base-to-tip spanwise flow is mainly maintained by the pressure-gradient force. The project supported by the National Natural Science Foundation of China (10232010)     

Investigation of vortex development on accelerating spanwise-flexible wings

The effect of spanwise flexibility on the development of leading-edge vortices for impulsively started flat plates at low Reynolds numbers has been investigated. A theoretical model is proposed, based on the Euler–Bernoulli beam theory, coupled with a vortex growth model based on vorticity flux through a leading-edge shear layer. The model was validated for rigid and flexible flat plates undergoing a towing motion at an angle-of-attack of 45°. It is shown that a phase-delay in lift and drag generation occurs between rigid and flexible cases. The model indicates decreasing vorticity along the span as the wing is accelerated and begins to bend. Particle image velocimetry measurements conducted at three different spanwise planes showed a delay in vortex growth along the span, despite a uniform spanwise circulation. This uniform spanwise distribution of circulation is in contrast to the quasi-two-dimensional model, which predicted a reduced circulation near the profile tip where plate motion was delayed. It is therefore concluded that circulation must be dynamically redistributed through vorticity convection during the impulsive motion.     

The effect of phase angle and wing spacing on tandem flapping wings

In a tandem wing configuration, the hindwing often operates in the wake of the forewing and, hence, its performance is affected by the vortices shed by the forewing. Changes in the phase angle between the flapping motions of the fore and the hind wings, as well as the spacing between them, can affect the resulting vortex/wing and vortex/vortex interactions. This study uses 2D numerical simulations to investigate how these changes affect the leading dege vortexes (LEV) generated by the hindwing and the resulting effect on the lift and thrust coefficients as well as the efficiencies. The tandem wing configuration was simulated using an incompressible Navier-Stokes solver at a chord-based Reynolds number of 5 000. A harmonic single frequency sinusoidal oscillation consisting of a combined pitch and plunge motion was used for the flapping wing kinematics at a Strouhal number of 0.3. Four different spacings ranging from 0.1 chords to 1 chord were tested at three different phase angles, 0°, 90° and 180°. It was found that changes in the spacing and phase angle affected the timing of the interaction between the vortex shed from the forewing and the hindwing. Such an interaction affects the LEV formation on the hindwing and results in changes in aerodynamic force production and efficiencies of the hindwing. It is also observed that changing the phase angle has a similar effect as changing the spacing. The results further show that at different spacings the peak force generation occurs at different phase angles, as do the peak efficiencies.     

The flexibility effect of a plate according to various angles of attack in a free-stream

This paper presents a computational fluid–structure interaction analysis for a flexible plate in a free-stream to investigate the effects of flexibility and angle of attack on force generation. A Lattice Boltzmann Method with an immersed boundary technique using a direct forcing scheme model of the fluid is coupled to a finite element model with rectangular bending elements. We investigated the effects of various angles of attack of a flexible plate fixed at one of the end edges in a free-stream at a Reynolds number of 5000, which represents the wing flapping condition of insects and small birds in nature. The lift of the flexible plate is maintained at the large angle of attack, whereas the rigid plate shows the largest lift at angles of attack around 30–40° and then drastic reductions in the lift at the large angle of attack. If we consider the efficiency as the lift divided by the drag, the flexible plate shows better efficiency at angles of attack greater than 30° compared to the rigid plate. The better performance of the flexible plate at large angles of attack comes from the deformation of the plate, which produces an interaction between the trailing edge vortex and the short edge vortex. The horseshoe-shaped vortex produced by a large vortex interaction at the trailing edge side has an important role in increasing the lift, and the small projection area due to the deformation reduces the drag. Furthermore, we investigate the role of flexibility on the lift and the drag force of the rectangular plate in a free-stream as the Reynolds number increases. Whenever a large vortex interaction at the trailing edge side is shown, the efficiency of the rectangular plate is improved. Especially, the flexible plate shows better efficiency as the Reynolds number increases regardless of the angle of attack.     

The effect of a small isolated roughness element on the forces on a sphere in uniform flow

The effect of an isolated roughness element on the forces on a sphere was examined for a Reynolds number range of 5 × 10⁴ < Re < 5 × 10⁵ using a novel sting-mounted sphere apparatus. The roughness element was a circular cylinder, and its width and height was varied to be 1, 2, and 4% of the sphere diameter. At subcritical Re, a lateral force is produced in the direction of the roughness, while at supercritical Re, the force is in the opposite direction. This is caused by asymmetric boundary layer separation, as shown using particle image velocimetry. At supercritical Re, a roughness element that is only 1% the sphere diameter produces a lift to drag ratio of almost one. It was found that the isolated roughness element has the largest effect on the lateral forces when it is located between a streamwise angle of about 40° and 80°. In addition to the mean forces, the unsteady forces were also measured. It was found that at subcritical Re, vortex shedding is aligned to the plane of the roughness element. In addition, the probability distribution of the forces was nearly Gaussian for subcritical Re, but for supercritical Re, the skewness and kurtosis deviate from Gaussian, and the details are dependent on the roughness size. A simple model developed for the vortical structure formed behind the roughness element can be extended to explain aspects of nominally smooth sphere flow, in which external disturbances perturb the sphere boundary layer in an azimuthally local sense. These results also form the basis of comparison for an investigation into the effectiveness of a moving isolated roughness element for manipulating sphere flow.     

Some observations in the vortex-turning behaviour of noncircular inclined jets

An experimental comparison was conducted for Re = 2,500, free elliptic and rectangular jets inclined at 30° and 60° along major or minor planes. Regardless of the jet base geometry, minor-plane inclined jets produced vortex roll-ups that remain inclined. In contrast, major-plane inclined jets produce significantly stronger vortex-roll-up turning behaviour. Interestingly, major-plane inclined rectangular jets exhibit strong vortex-overturning behaviour, where the vortex-roll-up inclination exceeds the 0° incline angle considerably. Vortex-turning extents and rates are compared between major-plane inclined elliptic and rectangular jets here and support present qualitative observations. Closer inspections reveal that the lack of axis-switching phenomenon in major-plane inclined rectangular jets allows vortex-overturning behaviour. In addition, jet centreline deflection is most sensitive in minor-plane inclined jets, where increasing the incline angle leads to a decrease and an increase in the elliptic and rectangular jet deflection, respectively.     

Aperiodicity in the near field of full-scale rotor blade tip vortices

Blade tip vortices are the dominant vortical structures of the helicopter flow field. The inherent complexity of the vortex dynamics has led to an increasing interest in full-scale in situ experiments, where the near field, closely behind the blade, is of particular interest, since measures of vortex control mostly target this initial stage of development. To examine the near field, three-component particle image velocimetry (PIV) measurements of blade tip vortices of a full-scale helicopter in simulated hover flight in ground effect were conducted. A feasible and robust evaluation procedure was developed to minimise the shortcomings of full-scale PIV applications, such as a moderate spatial resolution and an elevated measurement noise level. At vortex ages ranging from y_v=1^°\psi_{\rm v}=1^{\circ} to 30°, a pronounced aperiodicity and asymmetry of the vortex were observed in -sections perpendicular to the vortex axes. At y_v=1^°\psi_{\rm v}=1^{\circ}, a preferential orientation of the vortex was observed. For increasing wake age, vortex wandering increased while the asymmetry of the vortex cores decreased. The high level of aperiodicity and core asymmetry must be taken into account when considering phase-averaged vortex characteristics in the near wake region.     

Evolution of a forced counter rotating vortex pair for two selected forcing frequencies

In this paper, results from an experimental study of the natural and forced evolution of a pair of counter rotating wing-tip vortices are reported. The vortices were generated using a pair of opposed wing-tips in a wind tunnel and measurements made up to 77 tip-spacings downstream of the models at a chord Reynolds number of 1.3 × 10⁵. The wake was interrogated using 2D particle image velocimetry and the long-wave Crow instability observed. Velocity data were recorded throughout the lifetime of the instability from initial growth through linking, formation of vortex rings and their subsequent decay. Forcing was achieved using pulsed air jets blowing in the span-wise direction from the wing tip and imparting spatially periodic perturbations to the vortices. Forcing at a frequency within the range amplified by the Crow instability was found to enhance the instability growth rate whereas forcing at a frequency outside the amplified range was found to inhibit instability growth. In the latter case the imparted wavelength was observed to die out with a preferred wavelength growing in its place.