可降解聚氨酯骨胶黏剂的研究

以ε-己内酯、乙交酯和D,L-丙交酯为单体,丙三醇为起始剂,辛酸亚锡为催化剂,合成了不同分子量的聚酯三元醇。随后将合成的聚酯三元醇引入到聚氨酯(PU)体系中,得到聚氨酯骨胶黏剂。利用核磁共振氢谱和红外光谱表征了聚酯三元醇和聚氨酯胶黏剂的结构。用扫描电子显微镜、万能拉力试验机、差示扫描量热分析仪及恒温震荡箱等研究了不同分子量聚酯三元醇及填料的加入对胶黏剂表面形貌、压缩性能、玻璃化转变温度(T_g)、黏接强度及降解性能的影响。结果表明:含有理论数均分子量为400的聚酯三元醇并添加填料的聚氨酯胶黏剂(PU-6C400-F)显示出较好的综合性能,黏接强度为0.93 MPa,压缩强度与模量分别为12.5 MPa与128.0 MPa,该体系有望取代聚甲基丙烯酸甲酯(PMMA)作为骨胶黏剂使用。     

水性聚氨酯荧光材料的制备及其荧光性能

将4-胺基-4′-(N,N-二苯基氨基)-1,2-二苯乙烯(ADAS)溶解于N,N-二甲基甲酰胺(DMF)中后分别以混合和接枝的方式引入水性聚氨酯,制备了不同软段和扩链剂的水性聚氨酯荧光材料(FWPU)。采用傅里叶变换红外光谱、荧光光谱表征了FWPU的结构和荧光性能。结果表明:水性聚氨酯的软段和扩链剂结构均可影响FWPU的荧光强度;与溶解同样浓度ADAS的DMF溶液相比,混合法制备的FWPU其荧光强度最大可以增加76倍,接枝法制备的FWPU最大可增加47倍。     

环氧改性水性聚氨酯乳液的制备及其膜性能

以聚己内酯二元醇(CAPA)为软段,异佛尔酮二异氰酸酯(IPDI)和六亚甲基二异氰酸酯(HDI)为硬段,环氧树脂E-44为大分子交联剂,经相转化法合成了一系列环氧树脂改性负离子水性聚氨酯(EPPU)自乳化乳液,并制备了改性水性聚氨酯的固化膜.通过FTIR、TGA及接触角、力学性能测试对聚合物结构及其膜性能进行了研究.通过原子力显微镜(AFM)观察膜表面形态和表面粗糙度.乳液粒径及粒径分布通过动态激光光散射法(DLLS)测定.FTIR分析表明环氧树脂的羟基和环氧基都参与了发应.TGA表明,环氧树脂的加入可以提高聚氨酯的热稳定性.随着w(E-44)增大,改性聚氨酯膜的拉伸强度得到改善,断裂伸长率减小.随着w(E-44)增大,乳液粒径增大,薄膜的接触角增大,改性后的PU膜表面光滑度下降,拒水性增强.     

水性聚氨酯结构与胶膜性能的关系

为制备一种性能优异的水性聚氨酯涂层,以聚丙二醇和异佛尔酮二异氰酸酯为主要原料,用本体聚合法制备了水性聚氨酯,考察了结构组元对胶膜性能的影响,并用激光粒度仪、微机控制电子万能试验机和同步热分析仪进行了表征。结果表明:当硬段含量增加时,乳液粒径增大,胶膜拉伸强度增加,吸水率升高;当异氰酸根指数增大时,乳液粒径增大,胶膜拉伸强度增加,吸水率降低;当亲水性扩链剂含量和中和度增大时,乳液粒径减小,胶膜的拉伸强度增加,吸水率升高;在硬段比例为50%、异氰酸酯指数为1.35、亲水性扩链剂含量为5%、中和度为1的条件下,胶膜性能较佳(拉伸强度为16MPa,断裂伸长率为556%,吸水率为6.2%)且在丙酮和甲苯中均表现出溶胀现象。     

扩链剂对脂肪族聚氨酯脲和聚脲弹性体结构与性能的影响

用异佛尔酮二胺(IPDA)、乙二胺(EDA)和己二胺(HDA)三种扩链剂合成了不同结构的脂肪族聚氨酯脲和聚脲, 并考察了扩链剂对聚氨酯脲和聚脲形态结构与性能的影响. 研究结果表明, 与EDA和HDA扩链的聚氨酯脲和聚脲相比, IPDA扩链的聚氨酯脲和聚脲中脲羰基的氢键化程度较低, 软段和硬段间的相混合程度较好; 同时它们具有更好的拉伸强度、硬度和撕裂强度, 但断裂伸长率较低. EDA和HDA扩链的聚氨酯脲和聚脲相比, 两者性能相差不大. 聚氨酯脲的脲羰基较完善氢键化程度以及整个氢键化程度都比聚脲的要低, 同时聚氨酯脲的吸水率也较低.     

聚氨酯/环氧树脂IPN复合抛光材料的制备及性能研究

本研究采用聚氨酯与环氧树脂(PU/EP)作为胶黏剂形成互穿网络(IPN),以无机磨料和稀土抛光剂为分散相,通过一定的成型工艺制备成复合抛光材料。通过固化前后的红外光谱,分析了PU、EP两者之间的反应;热重分析表明PU/EP IPN复合抛光材料的耐热性能比纯的PU和EP有显著提高;体视显微镜照片显示该复合抛光材料具有微孔结构;力学及应用性能研究显示当胶黏剂含量为25%时性能最佳;且在PU/EP=2时,抛光后的玻璃透光率保持原有的97%,且耐磨性得到大幅度提高。     

基于多巴胺的聚氨酯黏合剂的合成与性能

通过化学键将多巴胺引入聚氨酯侧链,制备出一种新型的聚氨酯黏合剂.首先通过四步化学反应制备了一种含多巴胺的新型聚氨酯功能扩链剂-多巴胺二羟甲基丙酰胺(DMPA-DA),然后将此扩链剂与1,4-丁二醇(BDO)按不同的比例,制备出一系列含多巴胺的新型聚氨酯热熔胶.利用FT-IR、1H-NMR、GPC、UV-Vis和剪切黏结强度性能测试等手段对该新型聚氨酯的结构和黏附性能进行了表征.结果表明:对于基材聚丙烯(PP),剪切黏结强度随着聚氨酯中多巴胺含量的增加而增强,含多巴胺的聚氨酯其剪切黏结强度达到了0.68 MPa,比不含多巴胺的聚氨酯增强了160％;对于基材低密度聚乙烯(LDPE)、Al、不锈钢,含多巴胺聚氨酯的剪切黏结强度分别达到2.00、1.70 MPa和4.55 MPa,比不含多巴胺的聚氨酯均增强了100％以上.     

季戊四醇型HTPB-PU弹性体的研究

以端羟基聚丁二烯、液化改性MDI为原料,季戊四醇为扩链剂与交联剂制备季戊四醇型聚氨酯,并用IR、TG、DSC和SEM对其进行表征;研究了影响季戊四醇型聚氨酯的力学性能和热性能的因素。结果表明：随扩链剂用量的增大,季戊四醇型聚氨酯的拉伸强度和硬度增大,而断裂伸长率减小,同时热稳定性得到提高。SEM显示此弹性体中存在明显的相分离。     

超支化聚氨酯热熔胶的合成及性能

采用AA′+bB2法制备了可以直接作为热熔胶使用的超支化聚氨酯(HPU). 以甲苯-2,4-二异氰酸酯(TDI)与聚碳酸酯二醇(PCDL)为原料合成两端为异氰酸根(NCO)封端的低聚物(A2),然后在0 ℃下加入二乙醇胺(DEOA)得AB2型中间物,进一步高温聚合得支化点间含有长链段的超支化聚氨酯. 采用红外光谱 (FTIR)、核磁共振(13C NMR)、GPC对超支化聚氨酯的结构进行了表征. 结果表明,所得到的产物具有超支化结构,在55 ℃下反应20 h后,支化度可达到0.75,重均分子量Mw=7.0×103. 对产物进行了热失重和粘接性能测试. 结果表明,超支化聚氨酯的热分解温度为200 ℃. 产物的粘接剪切强度随着链段长度的增加先增大后减小,最大可达到6.5 MPa.     

含多巴胺的聚柠檬酸酯基组织胶黏剂的制备

通过柠檬酸、1,8-辛二醇和多巴胺的一步熔融缩聚反应,以高碘酸钠(NaIO4)作为氧化交联剂,得到含有多巴胺的组织胶黏剂。探索了制备胶黏剂的最佳反应时间和多巴胺的最佳添加量,并利用凝胶渗透色谱(GPC)、红外光谱(FT-IR)、核磁共振氢谱(1 H-NMR)、紫外-可见分光光度法(UV-Vis)和黏结强度测试对胶黏剂的结构和性能进行了表征。结果表明:当反应时间为105min,柠檬酸、1,8-辛二醇和多巴胺的投料的物质的量之比为1.1∶1.0∶0.5时,可以得到黏结强度为99.3kPa的组织胶黏剂,达到商品α-氰基丙烯酸酯医用胶强度的40%。     

Preparation of waterborne polyurethane nanocomposites: Polymerization from functionalized hydroxyapatite

We report the preparation and characterization of waterborne polyurethane (WBPU)/hydroxyapatite (HAp) nanocomposites through in situ polymerization from functionalized HAp. The HAp nanoparticles (HAp NPs) were urethanated with 3-isocyanatemethyl-3,5,5-trimethyl-cyclohexylisocyanate (isophorone diisocyanate) to obtain grafted HAp NPs containing isocyanate groups (HAp-g-NCO) as crosslinkers and then the HAp-g-NCO is further polymerized with WBPU monomers to form the WBPU/HAp nanocomposites. The HAp NPs were homogeneously dispersed in the polyurethane matrix at low loading levels (?2.0 wt%), thus the mechanical strength and the elongation at break of the WBPU/HAp nanocomposites were significantly improved. Thermal stability and water resistance of the WBPU/HAp nanocomposites are also enhanced. These results suggest that the WBPU/HAp nanocomposites prepared by in situ polymerization hold the potential as new materials with improved mechanical properties, thermal stability and water resistance.     

Tensile Properties and Morphology of Oil Palm Empty Fruit Bunch Regenerated Cellulose Biocomposite Films

The regenerated cellulose (RC)biocomposite films were prepared using casting method where oil palm empty fruit bunch (OPEFB) and microcrystalline cellulose (MCC) were dissolved in N-dimethylacetamide/lithium chloride (DMAc/LiCl)solution. The increasing of OPEFB contents up to 2 wt% increased the tensile strength and modulus of elasticity of RC biocomposite films while the elongation at break decreased. However, at 3 and 4 wt% of OPEFB content, the tensile strength and modulus of elasticity decreased with increases OPEFB content, but elongation at break increased. The increment of tensile strength and modulus of elasticity at 2 wt% is due to the OPEFB fiber that partially dissolved and dispersed with the OPEFB matrix. The morphology studies illustrate that at 2 wt% of OPEFB content of biocomposite films surface consists less voids and agglomerations than at 4 wt%. This can be considered the RC filler was partially dispersed with the RC matrix in the biocomposite films.     

Tensile and flexural properties of polypropylene composites filled with highly effective flame retardant magnesium hydroxide

The reinforcing effects of highly effective flame retardant magnesium hydroxide (FMX) content on the tensile and flexural properties of filled polypropylene (PP) composites were investigated within the FMX weight fraction range from 5 to 60 wt%. It was found that the Young's modulus and flexural modulus increased approximately linearly while the tensile yield strength and tensile fracture strength decreased slightly with increasing the FMX weight fraction. When the FMX weight fraction was lower than 20%, the tensile elongation at break decreased considerably, and then decreased slightly; the flexural strength increased when the FMX weight fraction was lower than 30%, and then decreased slightly. The tensile properties increased with increasing rate of tension. Moreover, the tensile yield strength of the composites was estimated using an equation proposed in previous work, and good agreement was shown between the predicted and the measured data.     

Toughening polylactide by dynamic vulcanization with castor oil and different types of diisocyanates

Dynamic vulcanization of polylactide (PLA) with castor oil (CO) and three different diisocyanates, namely 4,4′-diphenylmethane diisocyanate (MDI), hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI), was performed to study the effect of diisocyanate type on the vulcanization process and on the morphology as well as mechanical properties of the PLA/CO-based polyurethane blends. The reactivity of the three diisocyanate followed the order of MDI > HDI > IPDI when reacting with castor oil. Interfacial compatibilization between PLA and the CO-based polyurethane occurred when the less reactive HDI and IPDI was used. Among all the blends, PLA/CO-IPDI showed the finest morphology and the best toughening efficiency. Incorporation of 20 wt% CO-IPDI increased the elongation at break and notched impact strength of PLA by 47.3 and 6.6 times, respectively. Cavitation induced matrix plastic deformation was observed as the toughening mechanism for the PLA blends with CO-based polyurethane. The effect of CO-IPDI content on the morphology and mechanical properties of PLA was studied in detail. The particle size of dispersed CO-IPDI and the elongation at break increased gradually, the tensile strength and Young's modulus decreased gradually, while the impact strength first increased and then decreased with increasing CO-IPDI content from 5 to 30 wt%. The maximum impact strength appeared for the blends with 20 wt% CO-IPDI.     

甲基丙烯酸羟乙酯改性水性聚氨酯乳液的制备及性能

采用种子溶胀乳液聚合法,以水性聚氨酯为种子,甲基丙烯酸羟乙酯、甲基丙烯酸甲酯和丙烯酸丁酯为单体制备水性聚氨酯丙烯酸酯复合乳液,考察了甲基丙烯酸羟乙酯含量对复合乳液的T型剥离、胶膜的硬度、耐水性和力学性能的影响。结果表明,随着甲基丙烯酸羟乙酯含量的增加,复合乳液的T型剥离强度、胶膜的硬度和拉伸强度增大,胶膜的耐水性先增大后减小,断裂伸长率有所降低,适宜的甲基丙烯酸羟乙酯用量为3%。     

Preparation and cryogenic mechanical properties of epoxy resins modified by poly(ethersulfone)

A thermoplastic, poly(ethersulfone) (PES) was used to modify a bisphenol‐F based epoxy resin cured with an aromatic diamine. The initial mixtures before curing, prepared by melt mixing, were homogeneous. Scanning electron microscopy (SEM) micrographs of solvent‐etched fracture surfaces of the cured blends indicated that phase separation occurred after curing. The cryogenic mechanical behaviors of the epoxy resins were studied in terms of tensile properties and Charpy impact strength at cryogenic temperature (77 K) and compared to their corresponding behaviors at room temperature (RT). The addition of PES generally improved the tensile strength, elongation at break, and impact strength at both RT and 77 K except the RT tensile strength at 25 phr PES content. It was interesting to observe that and the maximum values of the tensile strength, elongation at break, and impact strength occurred at 20 phr PES content where a co‐continuous phase formed. Young's modulus decreased slightly with the increase of the PES content. Moreover, the tensile strength and Young's modulus at 77 K were higher than those at RT at the same composition, whereas the elongation at break and impact strength showed the opposite results. Finally, the differential scanning calorimetry analysis showed that the glass transition temperature (T_g) was enhanced by the addition of PES. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 612–624, 2008     

Preparation and properties of sol–gel waterborne polyurethane adhesive

Waterborne polyurethane (WBPU) sol–gel adhesives were prepared through a prepolymer process followed by a sol–gel reaction of (3-aminopropyl)triethoxysilane (APTES). The terminal amine group of APTES reacted with the NCO group of the prepolymer, and the ethoxy group created Si–O–Si branching by hydrolysis and condensation reactions in water at the dispersion step. Water swelling (%), tensile strength and Young’s modulus of the synthesized WBPU sol–gel adhesives were improved by increasing APTES content. Synthesized WBPU sol–gel adhesives were used for bonding nylon fabrics. A significant improvement in adhesive strength was recorded, and the potential for good adhesive strength under water at moderately high temperature (up to 75 °C) was observed with 6.84 mol% APTES in WBPU sol–gel adhesives.     

Synthesis and Characterization of Thermoplastic Polyurethaneureas based on Polyisobutylene and Poly(tetramethylene oxide) Segments

New thermoplastic polyurethaneureas (TPUU) based on polyisobutylene (PIB) and poly(tetramethylene oxide) (PTMO) segments have been synthesized possessing tensile properties comparable to conventional PTMO based TPUs. PIB based TPUU containing 35 weight (wt)% hard segment was synthesized by chain extension of H₂N-Allyl-PIB-Allyl-NH₂ with 4,4′ -methylene bis(phenylisocyanate) (MDI) and 1,4-butanediol (BDO) in toluene. The ultimate tensile strength (UTS) = 12 MPa and ultimate elongation = 70% were inferior to PTMO based polyurethane (UTS = 35 MPa, elongation at break = 600%). H₂N-Allyl-PIB-Allyl-NH₂ and HO-PTMO-OH in different proportions were chain extended in presence of MDI and BDO to obtain TPUUs containing 35 wt% hard segment. The polymers exhibited M _ns = 84000–138000 with polydispersity indices (PDIs) = 1.7–3.7. The UTS = 23–32 MPa and elongation at break = 250–675% was comparable to that of PTMO based polyurethane and significantly higher than the PIB based TPUU with the same Shore hardness. The Young's modulus of the polymers was strongly dependent and directly proportional to the PIB wt% in the SS of the TPUUs.     

脂肪族水性聚氨酯的力学性能研究

考察了软段的种类、分子量大小、混合软段的组成对产物力学性能的影响作用。同时还研究了二羟甲基丙酸(DMPA)用量以及中和剂的影响作用．实验结果表明。软段结构对脂肪族水性聚氨酯成膜的力学性能影响很大，聚酯型产物具有较高的模量和拉伸强度。聚醚型产物则具有较高的伸长率．混合软段对产物力学性能的影响较为复杂，随着软段中聚醚含量的升高，产物的硬度和模量均大幅度下降，但拉伸强度和伸长率的变化并不是一个线性关系．产物的模量随软段分子量的提高而降低，但伸长率和拉伸强度却有所提高．当DMPA用量较高时。产物的模量和拉伸强度均较高：当DMPA用量较低时，产物则具有较高的伸长率．中和剂的种类对产物力学性能的影响明显，当以NaOH为中和剂时，产物具有较高的硬度、模量、拉伸强度：以三乙胺为中和剂时，产物具有较高的伸长率．     

Morphologies and Mechanical Properties of Cis-1,4-butadiene Rubber/Polyethylene Blends

The mechanical properties and phase morphologies of cis-1,4-butadiene rubber(BR) blended with polyethylene(PE) at different blend ratios were studied. The tensile test results show that the PE exhibits excellent reinforcing capabilities towards BR. Blending BR with PE results in a remarkable enhancement of tensile strength, modulus and the elongation at break simultaneously. An increment of tensile strength from 1.11 MPa to 16.26 MPa was achieved by incorporation of 40 wt% PE in the blends. The modulus and elongation at break of 40/60 PE/BR blends are also about 5 times higher than those of the pure BR treated under exactly the same conditions. The tear test indicates that the tear strength also increases with the increase of PE content. It reaches 58.38 MPa for the 40/60 PE/BR blend, which is approximately 10 times higher than that of the pure BR. Morphological study demonstrates that the PE forms elongated microdomains finely dispersed in the BR matrix when its content is over 30 wt%, which corresponds to the remarkably enhanced mechanical properties.According to the results, reinforcement mechanism of PE toward BR dependent on the microstructure has been discussed and two different mechanisms have been proposed.