Spectrophotometric and gravimetric determination of sulfur in sebacate-base lubricants

Sulfur is determined in sebacate-base lubricants spectrophotometrically and gravimetrically. In the spectrophotometric method, a 0.2–0.3-g sample is treated with mixed acids, magnesium chloride is added, and the solution is evaporated to dryness. The sulfate is reduced to hydrogen sulfide by treatment with a mixture of hydriodic. hypophosphorous, and hydrochloric acids, and the hydrogen sulfide is distilled into ammonia solution. Lead citrate reagent is added and the brownish yellow color of lead sulfide sol is measured. An improved technique and apparatus for the distillation is described. In the gravimetric method, a 5-g sample is treated with mixed acids, antimony and tin are volatilized by treatment with hydrobromic acid, and sulfur is precipitated as barium sulfate. The recommended range of the spectrophotometric method is 0.005–0.15%,and that of the gravimetric method is 0.01–1% sulfur.     

D241树脂分离纯化黄芩总黄酮的研究

本文研究了用241树脂分离纯化黄芩总黄酮的方法和工艺。实验结果表明：D241树脂对黄芩总黄酮的静态交换容量是77mg/ml树脂。在pH11.0、流速2.0BV/h、提取液中总黄酮浓度17.5mg/ml条件下，D241树脂对黄芩总黄酮的动态交换容量为43.8mg/ml。用60％甲醇作为黄芩总黄酮洗脱剂，在PH4.0、洗脱流速1.5BV/h条件下，4．5BV洗脱剂即可完全洗脱被D241树脂交换的黄芩总黄酮。与酸沉淀法相比较，经过除去果胶，总黄酮纯度由33．34％提高到74．9％，粗品收得率由11.52%降低至4.83%；经过D241树脂分离纯化，其纯度达到91.5%，产品收得率3.54%。     

水性聚氨酯的制备及其性能的研究

本文以琥珀酸酐与三羟甲基丙烷反应,制得了含有羟基和羧基的酯类亲水性单体,并以此单体与ＴＤＩ和ＰＰＧ－１０００反应,制得了含有羧基的聚氨酯预聚体,在三乙醇胺水溶液中分散得到了水性聚氨酯（简称ＷＰＵ）。本文对预聚体的溶剂种类和用量,对乳胶粒的大小及形状的影响进行了研究,确认溶剂的用量越大,乳胶的粒径就越小;以丙酮作溶剂,乳胶粒为棒状或橄榄球状,而以丁酮为溶剂,得到的乳胶粒为圆球状。通过改变亲水单体的用     

A rapid solvent extraction method for the determination of caesium-137 in environmental materials

A solvent extraction method for the quantitative determination of caesium-137 in environmental samples is described. Caesium carrier is added to the ashed sample, which is dissolved with hydrochloric acid. The solution is filtered to remove any carbon and the pH is adjusted to 2.0. Sodium dodecylbenzene sulphonate is added and the extraction is done with phenol-nitrobenzene mixture. The organic phase is washed with EDTA solution and the caesium is stripped from the washed solvent with 6 M hydrochloric acid. The caesium is precipitated as caesium chlorostannate to ensure absolute decontamination from potassium-40. Recovery from standard solution is about 85% and from vegetation, rainwater and effluent samples about 80%. The method is applicable in the presence of large quantities of interfering ions, and decontamination factors for many nuclides are greater than 10³.     

Vibrational-translational energy transfer n atom-polyatomic molecule collisions in thermal reaction systems

Vibrational-translational energy transfer probabilities and collisional efficiencies are calculated for atom-polyatomic molecule collisions. It is assumed that a collision complex is formed and that the total internal vibrational energy is statistically distributed among all the modes of the complex. An attractive potential is assumed and account is taken of the centrifugal barrier. Conservation of system angular momentum is imposed. Convolution of the several thermal distribution functions is carried out and completeness and detailed balance are observed. Comparison of calculated quantum statistical quantities with experiment is made for the thermal isomerization of methyl and ethyl isocyanide in the presence of heavy atomic bath gases, such as Xe or Ar, and semiquantitative agreement is found.     

山东省主栽果树生殖器官中稀土与微量营养元素的相关性研究

通过对山东省5大类主栽果树20余个树种的花粉、种子和果实稀土与微量元素自然含量进行分析比较, 认为稀土(RE)与微量元素在各树种花粉中平均含量顺序为Fe＞Zn＞B＞Cu＞Mn＞RE, 种子中B＞Fe＞Zn＞Mn＞Cu＞RE, 果实中Fe＞B＞Zn＞Cu＞Mn＞RE. 各元素在各生殖器官中的自然分布因树种而有很大差异. 但基本规律类同, 即花粉＞种子＞果实. 花粉富集各种微量营养元素的能力都很强. 花粉和果实稀土与微量元素之间绝大多数呈正相关, 种子大多呈负相关, 但相关性均不显著.     

N,O-羧甲基壳聚糖的合成和性质研究

采用多段升温法将壳聚糖改性,合成了取代度为1.84、平均分子量为3.08×105、等电点为7.28的N,O-羧甲基壳聚糖(CMC),分别用紫外光谱、红外光谱、荧光光谱对其结构进行了表征,并对其水溶液的Zeta电位、电导率、表面张力以及水分散体系中羧甲基壳聚糖微粒的粒径分布进行了研究.结果表明, N,O-羧甲基壳聚糖具有表面活性;介质的pH值和浓度对羧甲基壳聚糖溶液的稳定性有很大的影响.     

氟吗啉合成工艺热危险性及动力学研究

氟吗啉是一种新型杀菌剂, 合成工艺热危险性和动力学研究将解决工程问题, 并保障安全生产. 采用差示扫描量热-热重分析仪(DSC-TG)测试主要原料、中间体和产品的热稳定性, 采用反应量热仪(RC1)研究反应热行为, 同时开展反应动力学研究. 研究结果显示, 主要中间体(3,4-二甲氧基苯基)(4-氟苯基)甲酮吸热分解温度为559.3 K, 乙酰吗啉吸热分解温度为478.2 K, 氟吗啉吸热分解温度为638.6 K. 氟吗啉合成反应摩尔放热量为15.44 kJ/mol, 绝热温升ΔT_ad为9.1 K, 本研究合成工艺的热危险性较小. 氟吗啉合成反应动力学方程为：r_A=kc_A^a=8.34×10^-3C_A^0.57, 对主要中间体(3,4-二甲氧基苯基)(4-氟苯基)甲酮的反应级数为0.57 级.     

用计算全息法检测卡塞格林系统主镜

为实现对卡塞格林光学系统中的非球面主镜表面面形的高精度检测,设计了一种二元位相型计算全息图(CGH)。介绍了工作原理,对CGH的相位模型参数的优化设计、衍射次级分离以及台阶位置与深度计算等关键问题进行了讨论。通过引入虚拟玻璃的概念快速建立非球面检测模型,针对卡塞格林系统主镜中心开孔的特点,通过加入同轴载波实现了衍射次级的完全分离,相比目前常用的倾斜载波方法简化了相位量化复杂度,数值仿真计算出了最优的台阶深度,降低了加工难度。给出了相应的设计方法及实例,研制投产了CGH。测试得到主镜面形的均方根误差为0.018λ,并与传统补偿器结果(RMS=0.019λ)进行对比,两者测试结果吻合,验证了该设计与检测方法的正确性,该设计方法简单快捷,适用于卡塞格林光学系统主镜面形检测。     

Precolumn,Capillary Column,Electron Capture G-AS Chromatography For High Efficiency Trace Determination

Abstract

A method for gas chromatographic trace determination is described in which the sample solution is injected into a packed precolumn which is connected to an EC-detector. When solvent and low boiling compounds have been eluted, the precolumn is connected to the cold entry of a capillary column with another EC-detector and the trace compound is collected as a narrow band at the entry of this column. The precolumn is then reconnected to its own detector, the capillary column is heated and the trace compound is eluted and measured. Meanwhile high boiling compounds are swept out of the precolumn. When the base line of the precolumn is stable the next sample is injected and the capillary column is cooled again, and so on. In order to avoid background plateaus and ghost peaks the carrier gas must be purified, which is easily achieved with cooling traps with dry-ice and acetone.     

Staircase voltammetry with finite diffusion space

A theory of the staircase voltammetry in a thin-layer cell is developed. The influence of the cell thickness and the redox reaction rate constant on the current and the peak potentials is analyzed. For moderately thick cells, the kinetic maximum is predicted. The relationship between peak currents and the square root of the scan rate is not linear and the response may entirely vanish if the redox reaction is fast, the cell is very thin and the scan rate is slow.     

Determination of free, total, and esterified cholesterol by high-performance liquid chromatography

A method is described for measuring free, total, and esterified cholesterol in blood serum in which reversed-phase liquid chromatography is used and the eluate is monitored at 200 nm. The sample for total cholesterol is prepared according to the Abell-Kendall procedure, and for free cholesterol an extract of serum--isopropanol (1:5, v/v) is used. The column is a muBondapak C18, 10 micrometers, and the mobile phase for total cholesterol is isopropanol--acetonitrile (50:50, v/v); for free cholesterol, it is isopropanol--acetonitrile--water (60:30:10). An approximation of the free cholesterol, triglycerides, and individual cholesteryl esters is obtained from single chromatograms of isopropanol extracts of serum if the first mobile phase is used. In a comparison study with the Abell-Kendall method for total cholesterol, the correlation is excellent and the precision is acceptable.     

Spectrophotometric determination of pentaerythritol tetranitrate (PETN) in waste water from lead styphnate primer plants

An accurate spectrophotometric method is proposed for the determination of pentaerythritol tetranitrate (PETN) in waste water from lead styphnate primer plants by use of phenoldisulphonic acid. The waste water is filtered through a sintered glass crucible and the PETN is determined in the filtrate and the residue. In the determination of PETN in the filtrate, sodium hydroxide is added and the PETN is extracted with methylene chloride (in alkaline solution, styphnate and TNT are not extracted). The methylene chloride solution is then evaporated to dryness, the residue is treated with a solution of phenoldisulphonic acid in sulphuric acid, water and ammonia are added, and the yellow colour is measured. In the determination of PETN in the residue, the PETN is dissolved in acetone, an aliquot of the acetone solution is treated with water and sodium hydroxide, the PETN is extracted with methylene chloride and the colour is developed as above. Various factors affecting the determination were investigated. The solubility of PETN in water was studied.     

Wastewater treatment using nanomaterial quaternary photocatalyst ZrCdPbO4 - Removal of colour pollutant by an eco friendly process

Pollution of environment is a major issue and has drawn attention of researchers throughout the globe. Water is polluted by various means like excretion of various industries and house releases, for example release of yarn, paper, and cloth industries etc. Present investigation consists of removal of such a pollutant. For this, synthesis of a novel quaternary nano particle sized photocatalyst ZrCdPbO₄ is carried and its characterization by different analytical techniques is also carried out. This is further used for removal of colour pollutants from the environment and Erythrosine-B is considered as a role model. Effect of various operational parameters like pH, concentration of dye, amount of photocatalyst, irradiation power etc. is studied, maximum degradation condition is extracted, and it is observed that reaction follows pseudo first order kinetics. Scavenger study suggests the participation of OH free radical in the reaction. Complete degradation of the dye in presence of light and photocatalyst is reported here by. Reusability of the photocatalyst is tested and is found to work up to five cycles efficiently.     

Chronoamperometric current at finite disk electrodes

The chronoamperometric current at a stationary finite disk electrode is studied using both analytical and digital simulation techniques. The exact long-time expansion of the current is obtained and its short-time behavior is considered. Digital simulation of the current using an explicit hopscotch algorithm is presented. In contrast to the usual explicit difference method, the ‘hopscotch’ algorithm is unconditionally stable, and thus, it is particularly suited for studying electrochemical problems at intermediate and long times. A simple analytic expressions for the current, which is accurate to 0.6% for all times, is presented.     

间苯二酚光度法测定环氧丙烷中丙醛的研究

在聚氨酯生产中,环氧丙烷中醛类物质含量直接影响聚醚质量,需要严格检查、控制。醛类物质的测定,目前国内外一般采用色谱法或比色法。也有用Hg~(2+)盐安培滴定法测定芳香醛。用2,4-二硝基苯肼直流极谱法测定醛,用原子吸收法测定低分子量醛和酮。我们根据间苯二酚与丙醛在果糖和浓盐酸作用下生成红色醌式产物的特性,较详细地研究了间苯二酚光度法测定环氧丙烷中微量丙醛的最佳条件和干扰因素。结果表明,本法灵敏度高、稳定性好,应用范围广。     

Polymers for Enhanced Oil Recovery Technology

Recently enhance oil recovery (EOR) technology is getting more attention by many countries since energy crises are getting worse and frightened. One of the reasons for this is due to the shortage of current oil resources and difficulties in finding a new oil field. Indonesia is one of the examples, before 2004 Indonesia is a net oil exporting country but after that Indonesia is a net oil importing country. The oil demand in the country is increasing while the oil production capacity is decreasing. In fact, when a new oil reservoir is drilled, the oil amount obtained from it is about 20-40% of the potential and hence there is still 60-80% oil left in the reservoir. Application of EOR technology gives an additional chance to get out more oil from the reservoir, possibly about another 20%. Polymer is the material that plays an important role in the application of EOR technology, especially surfactant and hydrogel polymers. In the technology, surfactant polymer is injected to the reservoir to reduce an interfacial tension between oil and water and is able to wipe out the trapped oil from the reservoir rock and hence increase the oil production. While an injection of hydrogel polymer to the reservoir is to increase a viscosity of fluid containing water so that the fluid is more difficult to flow than the oil, and as a result, the oil production increases. The most common polymer used for this application is polyacrylamide group.     

流动注射分光光度法测定矿物浸提液中的游离氰化物

在氢氧化钠介质中游离的氰化物与苦味酸钠反应生成玫瑰红酸钠，并进行升温改善反应条件。双流路系统与单流路相比，峰形规范、光滑，能有效消除鬼峰，优化了显色条件，工作波长为５１０ｎｍ。按生产工艺要求的线性范围为４．０￣４０．０ｍｍｏｌ／Ｌ。进样频率为１３０次／ｈ。已成功地用于矿物浸提液中游离氰化物的现场分析。     

Photogalvanic cells: Part VIII. The theory of the transparent rotating disc electrode

The theory of the transparent rotating disc electrode is first extended to cover the case where two photogenerated species react with second-order kinetics and where one of the species is electroactive and the other is not. Secondly the theory is developed to describe the case where the solution is bleached close to the electrode. Thirdly theory is presented for experiments where the light source is modulated and the phase shift and amplitude of the resulting modulated photocurrent are measured.     

聚苯胺薄膜电极上示差脉冲伏安法可逆波理论研究

本文提出了聚苯胺(PANI)薄膜电极上示差脉冲伏安法可逆波理论,经验证理论和实验结果相符合.