Importance of the diamine reactant in the production of polyphosphonamides by the interfacial technique

The stirred interfacial polycondensation of phenylphosphonic dichloride and 1,6-hexanediamine has been studied as a function of several reaction variables. The reaction is rapid, being completed in less than 1 min. When organic solvent is varied and reactant molar ratio is varied with an excess of the acid chloride, yield is constant. When reactant molar ratio is varied polymer yield increases with increase in amine concentration. When reactant concentration is increased yield increases. With the addition of a soluble salt in the aqueous phase yield is increased. The above indicates that the diffusion of the amine to the reaction zone is of primary importance in determining polymerization rate and that the diffusion of the acid chloride is relatively unimportant. Polymer yield was found to be dependent on the pH of the amine in the aqueous phase. The observed trend is related to the apparent solubility of the amine in the aqueous phase such that the greater the apparent solubility of the amine, the less the polymer yield. Polymer molecular weight is found to be independent of reaction variables tested. Polymer was also formed from the condensation of phenylphosphonic dichloride with p-phenylenediamine, H₂N-D-NH₂ (where D is a 36-carbon hydrocarbon chain), 1,3-di-4-piperidylpropane, and 4-aminomethylpiperidine; phenyl phosphorodichloridate with 1,6-hexanediamine; chloromethyl phosphonic dichloride with 1,6-hexanediamine.     

UV‐responsive degradable polymers derived from 1‐(4‐aminophenyl) ethane‐1,2‐diol

A UV‐responsive polymer was prepared via condensation polymerization of 2‐nitrobenzyl(4‐(1,2‐dihydroxyethyl)phenyl)carbamate and azalaic acid dichloride. When the polymer was irradiated with UV light, the nitrobenzyl urethane protecting group was removed and the deprotected aniline underwent spontaneous 1,6‐elimination reactions, resulting in degradation of the polymer. Nanoparticles with encapsulated Nile Red were formulated with the degradable polymer and triggered burst release of Nile Red was observed when the nanoparticles were irradiated by UV light. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1161–1168     

Kinetic study of the alternating copolymerization of butadiene and methyl methacrylate

A kinetic investigation of the alternating copolymerization of butadiene and methyl methacrylate with the use of a system of ethylaluminum dichloride and vanadyl chloride as a catalyst was undertaken. The relation between the polymer yield and the molar fraction of methyl methacrylate in the feed was examined by continuous variation of butadiene and methyl methacrylate, the concentrations of total monomer, ethylaluminum dichloride, and vanadyl chloride being kept constant. This continuous variation method revealed that the polymer yield attains its maximum value with a monomer feed containing less than the 0.5 molar fraction of methyl methacrylate. This value of the molar fraction of methyl methacrylate affording the maximum polymer yield decreased on increasing the total monomer concentration but was not changed on varying the concentration of ethylaluminum dichloride. The number of active species estimated from the relation between yield and molecular weight of the polymer was almost constant, regardless of the molar fraction of methyl methacrylate in the feed. Consequently, it can be said that the maximum polymer yield depends mainly on the propagation reaction, not on the initiation reaction or the termination reaction. Three types of the mechanism have been discussed for this alternating copolymerization: polymerization via alternating addition of butadiene and methyl methacrylate complexed with ethylaluminum dichloride by the Lewis-Mayo scheme; polymerization via the ternary intermediate of butadiene, methyl methacrylate, and ethylaluminum dichloride; polymerization via the complex formation of butadiene and methyl methacrylate complexed with ethylaluminum dichloride occurring only at the growing polymer radical. From the kinetic results obtained, it was shown that the first and third schemes are excluded, and polymerization by way of the ternary intermediate is compatible with the data.     

Preparation and photocrosslinking behaviors of polyesters derived from trans-2,2′-dihydroxystilbene

The monomer, trans-2,2′-dihydroxystilbene (DHS), has been prepared by asymmetric photocleavage (254 nm) of coumarin dimer acid derived from coumarin dimer. Four new polyesters are successfully synthesized by interfacial polycondensation of the DHS with adipoyl chloride, azelaoyl chloride, sebacoyl chloride, and dodecanedioyl dichloride, respectively. The reduced viscosities of the polyesters decrease from 0.32 to 0.11 dL/g as the number of methylene unit in diacid chlorides increases from 4 to 10. From DSC investigation, it is found that the polyesters are semi-crystalline polymers with T_m = 39–192°C. Under 350 nm light, photocrosslinking behavior in solution and film-state is investigated by UV spectral change with irradiation time (350 nm). The photoreactive stilbene chromophores in the main chain dimerize to form cyclobutane derivatives, and lead to crosslinking of the polyesters. Photosensitivity in the film state has also been evaluated by their characteristic curves. Polyester from dodecanedioyl dichloride ( 5d ) exhibits the highest initial reaction rate and ultimate crosslinking ratio. © 1995 John Wiley & Sons, Inc.     

Synthesis and Characterization of Polysulfide Rubber Using Phase Transfer Catalyst

Summary : Poly(alkyltetrasulfide) is prepared via reaction of ethylene dichloride with sodium tetrasulfide (Na₂S₄) in the presence of methyl tributyl ammonium chloride as phase transfer catalyst (PTC). The polysulfide polymer is characterized by CHN analysis, FT-IR, TGA, DTA and DSC techniques.     

Preparation of soluble and fusible poly(2,5-dimethoxy-1,4-phenylene)

Poly(2,5-dimethoxy-1,4-phenylene) was prepared by oxidative polymerization of p-dimethoxybenzene with aluminum chloride and copper(II) chloride in nitrobenzene under reduced pressure. The polymers obtained were soluble in sulfuric acid and fusible at 320°C. The intrinsic viscosity of the polymer was ca. 0.07 in sulfuric acid. Demethylation of methoxy groups did not occur during the polymerization.     

Schwefel-stickstoff-verbindungen VII. Darstellung und reaktionen einiger perfluoraromatischer schwefel-stickstoff-verbindungen

Some reactions of the derivatives of pentafluorobenzenesulfenic, -sulfinic, and -sulfonic acid are described. By the reaction with thionyl chloride N-sulfinylpentafluorobenzenesulfenamide and -sulfonamide were prepared. N-sulfinylpentafluorobenzenesulfenamide was also prepared by the reaction of pentafluorobenzenesulfenyl chloride with N-sulfinyltrimethylsilylamine. Furthermore the reaction of bis(pentafluorophenylthio)amine with thionyl chloride and the reactions of pentafluorobenzenesulfenamide with sulfur dichloride and sulfur tetrafluoride were investigated.     

Synthesis and Structure of Tri(p-tolyl)antimony Dichloride

Tri(p-tolyl)antimony dichloride was prepared by oxidation of tri(p-tolyl)stibine with chlorine or copper(II) chloride. As found by X-ray diffraction analysis, the antimony atom in tri(p-tolyl)antimony dichloride has the configuration of trigonal bipyramid with axially located chlorine atoms. The Sb-Cl and Sb-C distances are 2.476(2) and 2.104(7) Å, and the CSbC and ClSbCl angles are 120 and 180°, respectively.     

Radiochemical studies of free-radical vinyl polymerizations. VI. Polymerization of methyl methacrylate in the presence of organotin PVC stabilizers

¹⁴C-Azoisobutyronitrile was used to initiate polymerizations of methyl methacrylate in the presence of the organotin compounds: tetrabutyltin, dibutyltin diacetate, dibutyltin dilaurate, dibutyltin di(ethyl mercaptide), dibutyltin di(dodecyl mercaptide), and dibutyltin dichloride. Only dibutyltin dichloride affected rates of polymerization significantly, and this was ascribed to an increase in the velocity constant k_p for the propogation reaction. No evidence was obtained for radical displacement reactions of the polymer radicals with bonds between tin and carbon, oxygen, sulfur, or chlorine. Transfer activity exhibited by the mercaptides was ascribed to traces of thiol impurity, possibly formed during storage. The relevance of these results to the mechanism of stabilization of poly(vinyl chloride) is briefly discussed.     

Polyesters,polyurethanes, and epoxy resin derived from 2,2′-(1,4-phenylenedivinylene)bis-5-hydroxypyridine

2,2′-(1,4-Phenylenedivinylene)bis-5-hydroxypyridine (PBHP) was used as a starting material for preparing new polyesters and polyurethanes as well as a diepoxide-bearing styrylpyridine segments. The diesters were prepared by reacting PBHP with terephthaloyl or adipoyl dichloride utilizing the interfacial polycondensation method. The diesters were prepared from the reaction of PBHP with tolylene diisocyanate or methylenebis(4-phenylisocyanate). In addition, a model diester and diurethane were synthesized by reacting PBHP with benzoyl chloride and phenyl isocyanate, respectively. Both model compounds and polymers were characterized by IR and ¹H-NMR spectroscopy, as well as by DTA and TGA. A diepoxide was also prepared from the reaction of PBHP with epichlorohydrin which was polymerized in the presence of 4,4′-diaminodiphenylsulfone. The polyester derived from PBHP and terephthaloyl dichloride was the most thermostable polymer obtained. It was stable in N₂ up to 355°C and afforded an anaerobic char yield of 59% at 800°C. The thermal stabilities of polymers were improved by curing.     

New block copolymers V. Synthesis,characterization and morphological studies of poly(pentamethylene terephthalate)-b-(acrylonitrile butadiene rubber)

A block copolymer was prepared by low temperature polycondensation between (acid chloride)-terminated poly(pentamethylene terephthalate) as the hard block, and amine-terminated acrylonitrile-butadiene rubber, as the soft block. The polymer was characterized by nitrogen analysis, IR and NMR spectroscopy. The polymer showed two glass transition temperatures (T _g ) and exhibited two-phase morphology.     

New processable polyaromatic ether-keto-sulfones curable by intramolecular cyclization. XV

New processable polyaromatic ether-keto-sulfones were prepared from 2,2′-diiododiphenyl-4,4′-dicarbonyl dichloride (I), bis(p-phenoxybenzene)sulfone (II), isophthaloyl chloride (III), and diphenyl ether (IV) in Friedel–Crafts-type polymerizations. In the most promising of the iodine-containing polymers phenylacetylenyl groups were introduced in place of iodine. This polymer, with an initial monomer ratio of I:II:III:IV = 1:5:7:3, was further investigated. It is soluble in DMF, DMA, pyridine, and sulfuric acid. After curing it was insoluble in all solvents used and lost only 1.1% of its weight at 300°C when heated in air for three days. Hence in this cured state it has excellent chemical and thermal resistance. It can be cast into a film from solution in DMAc and a glass fiber laminate is readily prepared. The film is tough, transparent, and brown in color. The cured film is tougher than the uncured. The glass fiber laminate is also tough and fairly flexible. A distinct advantage of this type of polymer is its ready availability in relatively cheap raw materials. The phenylacetylenyl-group-containing polymer showed a transition temperature at 175°C and two exotherm peaks at 243 and 361°C which disappeared after curing in a DSC thermogram. Before and after curing this polymer displayed softening temperatures at 149 and 171°C, respectively, measured by a Vicat apparatus at a heating rate of 1°C/min. No melting temperatures up to 500°C were observed for any of the polymers in this study.     

一种无机-有机高分子杂化催化剂Pd(0)-CS/MCM-41的制备及其性能研究

将天然高分子聚合物壳聚糖负载到MCM-41介孔分子筛上,再在室温与氯化钯乙醇溶液作用,制得了一种无机-有机天然高分子杂化催化剂Pd(0)-CS/MCM-41,并利用XPS、FTIR、XRD、热重等手段对其进行了表征。以碘代苯与丙烯酸的Heck芳基化反应考察了所得催化剂的催化性能。结果表明,催化剂具有较高的催化活性和良好的重复使用性能,催化剂在氮气保护下能有效地催化碘代苯与丙烯酸的Heck反应,高产率地得到反式肉桂酸。经8次重复使用后,肉桂酸的产率仍达80%以上。     

Aromatic polyesters obtained directly from hydroxybenzoic acids by hexachlorocyclotriphosphatriazene (PNC) in pyridine

Polyaryl esters of moderate molecular weights were prepared by the direct polycondensation reaction of hydroxybenzoic acids and its derivatives with hexachlorocyclotriphosphatriazene (also known as phosphonitrilic chloride trimer, PNC) as a condensing agent in pyridine. Copolymerization of p-hydroxybenzoic acid with several hydroxybenzic acid derivatives was carried out to improve the processability of the polymer of p-hydroxybenzoic acid, which yields fusible and soluble copolymers of high inherent viscosities. Polymer solubility and thermal behavior were examined.     

Reactions of <Emphasis Type="Italic">N</Emphasis>-(Perfluorophenyl)carbonimidoyl Dichloride with Aromatic Acids and Their Derivatives in the Presence of AlCl<Subscript>3</Subscript>. Formation of 2-(Perfluorophenyl)isoindoline-1,3-dione and Its Derivatives

Reactions of N-(perfluorophenyl)carbonimidoyl dichloride with benzoic acid, benzoyl chloride, ethyl benzoate, and also with phthalic acid, phthaloyl dichloride, and phthalic anhydride in the presence of AlCl₃ at 170°C afford2-(perfluorophenyl)isoindoline-1,3-dione. With benzoic acid and benzoyl chloride form also 2-(perfluorophenyl)-3-[(perfluorophenyl)imino]isoindolin-1-one. In reactions with compounds of the benzene series arise also derivatives of arylimidoyl chlorides and amide type compounds containing a CONHC₆F₅ moiety.__________Translated from Zhurnal Organicheskoi Khimii, Vol. 41, No. 2, 2005, pp. 228–236.Original Russian Text Copyright © 2005 by Petrova, Platonov.     

Titanocene (III) chloride mediated radical induced synthesis of (−)-methylenolactocin and (−)-protolichesterinic acid

Enantioselective synthesis of two anti-tumor antibiotics, (−)-methylenolactocin and (−)-protolichesterinic acid, has been achieved through titanocene(III) chloride mediated radical cyclization reaction starting from commercially available d-mannitol. Titanocene(III) chloride (Cp₂TiCl) was prepared in situ from commercially available titanocene dichloride (Cp₂TiCl₂) and zinc dust in THF.     

Block copolymer formation from copolymers of phenylvinylene carbonate

Copolymers of phenylvinylene carbonate with styrene and p-chlorostyrene are readily prepared with radical initiators. The carbonate portion of the copolymers has been hydrolyzed to a 1,2-glycol which was then oxididatively cleaved with periodate–perman-ganate to produce a polymer with carboxyl and keto endgroups. Block copolymers were then prepared by conversion of the carboxyl groups to an acid chloride, followed by coupling with diols or a diamine.     

Aripiprazole Loaded Polymeric Biodegradable Microspheres: Formulation and In Vitro Characterization

In the present study, we attempted to prepare biodegradable microspheres of polylactic acid containing aripiprazole in order to achieve its controlled release profile suitable for parenteral administration. Biodegradable microspheres were prepared by solvent evaporation method using methylene dichloride as a solvent. The optimization of various formulation variables (e.g., stirring speed, and polymer:drug ratio, stabilizer concentration) to obtain spherical particles was also investigated. The optimized product was further characterized for various in vitro attributes, such as particle size and its distribution, encapsulation efficiency, surface properties, percentage yield, and in vitro release. Changing the ratio of polymer, stabilizers, and leaching agent (sodium chloride) affected the entrapment efficiency and release rate of aripiprazole. The release quantum was 88.41% when stirring rate was 2000 rpm and it was further increased to 94.65% when stirring speed was increased to 3000 rpm (Formulation E). Drug entrapment of microspheres was increased by increasing the concentration of PVP and maximum entrapment (62.35%) was obtained at 4% concentration of PVP (Formulation E). Spherical particles with good surface characteristics were obtained at stirring rate 3000 rpm and drug:polymer ratio 1:10.     

Polymerization of coordinated monomers. XVII. Alternating copolymerization of methyl methacrylate with styrene by boron compounds

By the use of various boron compounds methyl methacrylate and styrene were copolymerized under photoirradiations at ?20°C. The alternately regulating activities of the boron compounds in the copolymerizations were in the following order: boron trichloride > ethylboron dichloride > boron trifluoride > diethylboron chloride ? triethylboron (?0). Boron trichloride and ethylboron dichloride exhibited such high regulating activities that their presence in 1 mol% in the charged methyl methacrylate was sufficient to complete equimolar alternating copolymerization. The alternating copolymerization proceeded in the steady state. The copolymerization rates decreased in the following order: boron trichloride ? ethylboron dichloride > diethylboron chloride ? triethylboron (?0). The cotacticities of methyl methacrylate-centered triads in the resulting copolymers were identical to those prepared with boron trichloride, ethylboron dichloride, and diethylboron chloride. The mechanism of the alternating copolymerization is discussed.     

Synthesis of aromatic polyesters by direct polycondensation with triphenylphosphine dichloride

Aromatic polyesters of high molecular weights were prepared by the direct polycondensation reaction of dicarboxylic acids and bisphenols or hydroxybenzoic acids with triphenylphosphine dichloride as a new condensing agent. Reaction conditions, including the amount of reagents and the concentration of monomer, solvent, and acid acceptor, were investigated. The aromatic polyester with the solution viscosity of 1.66 dL/g was obtained from bisphenol. A and terephthalic and isophthalic acid in quantitative yield under the optimum condition. The principal advantage of this condensing agent is that, based on the recycling system, recovered triphenylphosphine oxide can be reconverted to the reactive triphenylphosphine dichloride by treating with phosgene or oxalyl chloride.