Evaluation of Free Radical-Scavenging Activity of Sea Urchin Pigments Using HPTLC with Post-Chromatographic Derivatization

Chromatographic separation, analysis of in situ radical-scavenging activity, and quantitative analysis of green sea urchin shell pigments were carried out by online HPTLC-DAD and HPTLC-DPPH methods. Methanol:chloroform:acetic acid:water (11:50:5:2, v/v) was selected as the best mobile phase on silica gel plates for the separation of the pigments. Two pigment spots, S1 and S2, were observed on the TLC plates, while echinochrome A was not detected in the pigment extract of green sea urchin shells. Based on the estimated ID₅₀ values, the antiradical activity was S2 (0.043 μg) > S1 (0.058 μg) > echinochrome A (0.134 μg).     

Determination of hydrocarbon types in petroleum and coal-derived products by thin-layer chromatography/densitometry

Different methodologies based on thin-layer chromatography (TLC)/densitometry were used to separate and quantitate hydrocarbon types in middle distillates (gas oil), heavy distillates (lubricant) from petroleum, and coal-derived products. Thus, petroleum products were separated into saturates and aromatics by development, using n-hexane (9 min) followed by dichloromethane (4.5 min), of silica gel plates impregnated with berberine sulfate. Detection of saturates and aromatics was performed by fluorescence scanning using 365 nm as the excitation wavelength. Alternative detection of aromatics can be performed on either silica gel or berberine-impregnated plates by using ultraviolet (UV) densitometry at 250 nm. On the other hand, polar coal-derived products were separated into aromatics, polar compounds, and uneluted components by using silica gel plates and development with toluene (12 min), followed by dichloromethane-methanol (95 + 5, v/v), with detection by UV densitometry at 250 nm. In all cases, external standard calibration was used for quantitation. Results were validated by using standard methods or well-established techniques of the petrochemical industry. The potential usefulness of TLC/densitometry is discussed.     

LC Separation of Co-Existing Cetylpyridinium Chloride, Tetradecyltrimethylammonium Bromide and Dodecyltrimethylammonium Bromide on Silica TLC Plates with Aqueous-Organic Eluents

Thin-layer chromatography (TLC) of three cationic surfactants was performed on silica TLC plates with various solvent systems. The mutual separation of cetylpyridinium chloride (CPC), tetradecyltrimethylammonium bromide (TTAB) and dodecyltrimethylammonium bromide (DTAB) was achieved on silica TLC plates with ethanol: 1% aqueous ammonium chloride (4:6, v/v) as an eluent. Effects of cations and anions in the mobile phase on mobility and separation of CPC, TTAB and DTAB were examined. The interference due to the presence of metal cations as impurities on the resolution in the mixture of CPC, TTAB and DTAB was also examined. The limits of detection of CPC, TTAB and DTAB estimated were 0.015, 0.031 and 0.062 μg zone⁻¹, respectively. The developed method was utilized to identify these surfactants in different spiked water samples after their preliminary separation.     

Use of High Pressure Liquid Chromatography and Thin Layer Chromatography for the Separation and Detection of Testosterone and its Metabolites from in vitro Incubation Mixtures

Abstract

Testosterone and its 6β-, 7α-, and 16α-hydroxylated metabolites were resolved by high pressure liquid chromatography and thin layer chromatography. Separation by HPLC was achieved in less than 45 min on a microparticulate silica gel column using isocratic elution with isopro-panol:tetrahydrofuran:hexane (5:15:80) as the mobile phase. TLC systems utilizing silica gel on glass and plastic plates, and polysilicic acid on glass fiber sheets are presented. The monohydroxylated metabolites of testosterone formed during incubation of (¹⁴C)-testosterone with liver postmitochondrial preparations from adult male rats pre-treated with phenobarbital or Aroclor 1254 were separated and quantitated by both HPLC and TLC. The results using both techniques are compared with those obtained by paper chromatography.     

Planar chromatographic separation of petroleum residues and coal-derived liquids

Vacuum distillation residues from two petroleum crudes, a coal liquefaction extract and a coal tar pitch have been fractionated by planar chromatography (PC) using two solvent sequences: pyridine–acetonitrile and tetrahydrofuran (THF)–toluene. Fractions recovered from PC were examined by UV-fluorescence spectroscopy (UV-F), size-exclusion chromatography (SEC). UV-F and SEC of the whole samples showed differences in aromatic cluster size and molecular mass (MM) ranges which could be related to the different origins of the samples. The MM ranges indicated by SEC were greater for the vacuum residues than for coal-derived materials. However, the UV-F spectra of the fractions indicated that the petroleum residue fractions contained similar aromatic types, whereas the fractions from coal liquids contained significantly different aromatic types. SEC profiles of the fractions indicated a separation of coal-derived samples by increasing molecular size with increasing immobility in PC, whereas for petroleum fractions, the same trend was not apparent. MALDI-mass spectra of the set of original samples showed broadly similar ranges of MM distributions but additional work is necessary to identify appropriate matrices and procedures in order to improve the MALDI spectra.     

Ultra-thin-layer chromatography mass spectrometry and thin-layer chromatography mass spectrometry of single peptides of angiotensin-converting enzyme inhibitors

The separation of structurally related angiotensin-converting enzyme (ACE) inhibitors lisinopril, cilazapril, ramipril and quinapril and their corresponding active diacid forms (prilates) by conventional TLC silica gel 60 plates was contrasted with that afforded by monolithic ultra-thin-layer chromatographic (UTLC) plates. For the use of UTLC plates technical modifications of the commercially available equipments for the sample application, development and detection were made. Plates were developed in modified horizontal developing chamber using ethyl acetate-acetone-acetic acid-water (4:1:0.25:0.5, v/v). Detection of the separated compounds was performed densitometrically in absorption/reflectance mode at 220 nm and after exposure to iodine also by image analysis. The obtained results showed that monolithic layer is more efficient for the separation of structurally similar polar compounds, such as prilates than conventional silica layers. Identification of the compounds was confirmed by ESI-MS after their on-line extraction from the UTLC and TLC plates by means of Camag TLC-MS interface.     

Chromatographic Behaviour of Phenols on Aliphatic Amines Impregnated Thin Layers

Abstract

The chromatographic behaviour of 40 phenols on silica gel G plates impregnated with ethylenediamine, diethylenetriamine, triethylenetetramine and hexamine has been studied and its correlation with the equilibrium constants of the adducts formed by the interaction of phenols with ethylenediamine as an impregnant has been attempted. A suitable separation scheme for these phenols on silica gel G plates impregnated with ethylenediamine and hexamine has been worked out.     

Preparative thin-layer chromatographic separation and subsequent gas chromatographic-mass spectrometric analysis of monoacylglycerols derived from butter oil by fungal degradation.

A semi-micro method has been developed using preparative thin-layer chromatography (TLC) to separate acylglycerols for the subsequent analysis by gas chromatography-mass spectrometry (GC-MS). Monoacylglycerols (MAGs) were formed from butter oil by fungal degradation with Penicillium roquefortii. Total lipids were extracted with hexane-2-propanol (3:2, v/v) and separated on silica gel preparative TLC plates with fluorescence indicator (Merck). The plates were developed in hexane-diethyl ether-formic acid (80:20:2, v/v). Lipid bands were detected under UV light or with iodine vapour, removed and then extracted with hexane-2-propanol (3:2, v/v). The MAG band (RF 0.03) was silylated into trimethylsilyl (TMS) ethers. Structures and composition of MAG-TMS ethers were analysed by GC and GC-MS. Formation of characteristic ions for the identification of sn-1(3)- and sn-2-MAG isomers was discussed. The method is simple, inexpensive and powerful for the separation and analysis of relatively small amounts of MAGs (0.2-5.0 mg) formed from fungal degradation.     

Quantitation of polyamines using thin-layer chromatography and image analysis

Efficient separation of dansylated polyamines can be achieved by thin-layer chromatography (TLC). Quantitation, however, can be laborious because it requires removal of the silica gel and the fluorescing derivative from the glass plates, elution in a suitable solvent, and estimation with a fluorescence spectrophotometer. We report here a relatively simple and rapid method for the quantitation of dansylated polyamines that employs an image analyzer without removal from the glass TLC plates.     

Thin-layer chromatography of glucose and sorbitol on Cu(II)-impregnated silica gel plates

A thin-layer chromatographic (TLC) separation of glucose and sorbitol on Cu(II)-impregnated silica gel plates with n-propanol: water (4:1) v/v as developer and potassium permanganate as detecting reagent has been worked out. The new impregnant is completely insoluble in water and thus enables the use of an aqueous developer. The R_f-values are 55 and 10 for glucose and sorbitol, respectively.     

Chromatographic Behaviour of Amino Sugars on Metal Salt Impregnated Thin Layers

Abstract

Suitable TLC separation scheme for Amino Sugars on silica gel G plates impregnated with metal salt, using the solvent system methanol-acetone (50:10) has been worked out. The visualization of the spots was done by spraying with ninhydrin in 1 - butanol.     

Two-Phase Thin-Layer Chromatography

Abstract

Thin layer chromatography (TLC) is normally carried out on single-phase (adsorbent) plates. However, it may be necessary to use nore than one adsorbent to achieve the separation of complex mixtures. Literature reports indicate that the use of mixed phases in TLC is not very common, possibly because the plates are difficult to prepare and precoated single-phase plates of different absorbents are readily available (silica gel, reversed phase, cellulose. alumina, etc.).     

Comparison of Mobile Phases for Separation and Quantification of Lipids by One-Dimensional TLC on Preadsorbent High Performance Silica Gel Plates

Abstract

Twenty-four solvent systems reported in the literature for the one-dimensional TLC separation of lipids and phospholipids were compared under identical conditions using high performance preadsorbent silica gel plates. The best overall separation of mixtures of neutral lipid and phospholipid standards and compounds extracted from the digestive gland-gonad complex of Biomphalaria glabrata snails was obtained with a system utilizing consecutive development with chloroform-methanol-water (65:25:4), chloroform-hexane (3:1), and carbon tetrachloride. The best system for quantification of neutral lipids was hexane-diethyl ether-formic acid (80:20:2). R_f data are tabulated and results discussed for all systems tested.     

Optimization of the phase system in the analysis of polynuclear aromatics (PNA) from diesel engine exhaust by high performance liquid chromatography (HPLC)

Summary Polynuclear aromatics (PNA) were collected and enriched from diesel engine exhausts by means of a probe and an absorber system. Group separation of PNA from other constituents of exhaust was accomplished through elution with n-heptane on a silica column. A variety of phase systems ranging from unpolar to strong polar packings and eluents, respectively, were tested to resolve PNA into single species. Of these a n-octadecyl bonded silica packing and methanol/water was found to be the most optimal with regard to resolution for real PNA mixtures. Separation was completed within 2–3 h at isocratic conditions.Paper presented at Euroanalysis III, Dublin. August 20–25, 1978.     

Validated TLC-Image Analysis Method for Simultaneous Quantification of Curcuminoids in Curcuma longa

A simple and rapid thin layer chromatographic (TLC)-image analysis method was developed for simultaneous quantification of three curcuminoids; curcumin (CUR), desmethoxycurcumin (DES) and bisdesmethoxycurcumin (BIS), in Curcuma longa (turmeric). Chromatographic separation of the curcuminoids was achieved on silica gel 60 F254 TLC plates, using chloroform–hexane–methanol (1:1:0.1, v/v/v) as the mobile phase. Image analysis of the scanned TLC plate was performed by Photoshop 7.0 to quantify the amount of each curcuminoid. The method was validated and found to be accurate, reliable and convenient for the analysis of CUR, DES and BIS in turmeric.

     

Application of Thin-Layer Chromatography to High-Performance Liquid Chromatographic Separation of Steroidal Hormones and Cephalosporin Antibiotics

Abstract

High-performance liquid chromatographic (HPLC) separation of steroidal hormones and cephalosporin antibiotics was investigated by adsorption chromatography and reversed-phase chromatography, respectively.

Prior to the HPLC separation of these pharmaceuticals, silica gel thin-layer adsorption chromatography of steroidal hormones and reversed-phase thin-layer partition chromatography of cephalosporin antibiotics with chemically bonded dimethylsilyl silica gel were performed in order to obtain suitable HPLC separation systems.

In the separation of steroidal hormones, the same binary mobile phase ratios of TLC did not give satisfactory results in HPLC. For the sharp separation in HPLC, solvent strength in the binary solvent mixture used for TLC had to be decreased.

The difference in solvent strength for efficient separation between TLC and HPLC might be attributed to the fact that in HPLC the solvent elution power acts in an isocratic manner while in TLC it acts in a gradient manner.

On the other hand, a correlation of mobility between TLC and HPLC separation for cephalosporin antibiotics was obtained, and the possibility of direct transfer of chromatographic systems from TLC to HPLC for separation of these antibiotics was confirmed.     

Normal Phase TLC Separation of Enantiomers Using Chiral Ion Interaction Agents

Abstract

A method for the thin layer chromatographic (TLC) separation of enantiomers and diastereomers involving the use of chiral ion interaction agents is described. Several aromatic amino alcohols were resolved by TLC on diol and/or high performance silica gel plates using a mobile phase containing (1R)-(-)- ammonium-10-camphorsulfonate or N-benzoxycarbonyl-glycyl-L-proline (ZGP). Many of these chiral aromatic amino alcohols are of pharmacological importance as α- and β-adrenergic blockers, adrenergic compounds, and anti-glaucoma agents. A comparison was made between various N-CBZ-amino acid derivatives as chiral counter ions/chiral mobile phase additives (CMAs). These separations could not be achieved on other normal phase TLC stationary phases including microcrystalline cellulose, alumina and ordinary silica gel plates.     

Separation and determination of rofecoxib and its degradation products by TLC chromatography

A thin layer chromatography with densitometry method for the determination of rofecoxib and degradation products is described. The chromatographic separation was performed on silica gel TLC plates as a stationary phase and chloroform-acetone-toluene-glacial acetic acid (12: 5: 2: 0.1, v/v/v/v) as a mobile phase. Densitimetric detection was carried out at 256 nm. The method is of high sensitivity and low LOD and LOQ: from 0.35 μg/spot to 1.05 μg/spot. The recovery was satisfactory at 98.62%. In addition, the stability of rofecoxib in solutions was investigated, including an effect of solution pH, temperature and incubation time. The method is rapid, easy and selective, particularly for the analysis of rofecoxib formulations. The article is published in the original.     

Investigation of phenolic acids in yacon (Smallanthus sonchifolius) leaves and tubers

Thin-layer chromatographic (TLC) screening of crude extracts of dried leaves and tubers of yacon (Smallanthus sonchifolius, Asteraceae) and products of acid hydrolysis of tubers on the silica gel HPTLC plates using the developing solvents ethyl acetate-formic acid-water (85:10:15, v/v/v) and n-hexane-ethyl acetate-formic acid (20:19:1, v/v/v) proved the presence of chlorogenic, caffeic and ferulic acid. These phenolic acids were isolated from the crude extract of yacon leaves by preparative TLC, and identified after elution by HPLC/MS, as well as by direct injection of the crude extract into the HPLC/MS system. Acid hydrolysis of tubers released the increased amount of phenolic acids (e.g. caffeic acid and ferulic acid), flavonoid quercetin and an unidentified flavonoid, which was detected by TLC analysis. Ferulic acid, isomers of dicaffeoylquinic acid and still an unidentified derivative of chlorogenic acid (Mr = 562) as constituents of yacon leaves and ferulic acid as constituent of yacon tubers are reported here for the first time. These acids gave significant contribution to the radical scavenging activity detected directly on the TLC plate sprayed with 1,1-diphenyl-2-picrylhydrazyl (DPPH).     

Liquid Chromatography Analysis of Hippuric Acid

Abstract

Hippuric acid analysis by TLC is demonstrated. Both normal silica and reverse phase C¹⁸ TLC plates are used with fluorescent quenching to visualize the hippuric acid. Urine samples may be spotted directly or extracted with CHCl₃ to concentrate the hippurate. Tissues may be analyzed in this same manner. Aluminum backed Merck TLC plates give best normal phase separation of tissue extracts and Whatman C¹⁸ give best reverse phase separation of tissue extracts. A Kontes scanner may be used to directly analyze TLC plates or the bands may be removed and analyzed by ultraviolet spectroscopy. Confirmation may be done by mass spectrometry.