Montmorillonite‐based nanocomposites of polybenzoxazole: Synthesis and characterization (I)

Poly(amic acid) was synthesized by means of low‐temperature‐solution polymerization of 3,3′‐dihydroxybenzidine and pyromellitic dianhydride in N,N‐dimethylacetamide. The precursor polymer was heat‐treated at different temperatures to create a polybenzoxazole (PBO) through a polyimide (PI). PI containing the hydroxyl group was rearranged by decarboxylation with heat treatment, resulting in a fully aromatic PBO. Hexadecylamine was used as an organophilic alkylamine in organo‐clay. We have tried to clarify the intercalation of heterocyclic polymer chains to hexadecylamine–montmorillonite (C₁₆‐MMT) and improve tensile properties. It was found that the addition of only a small amount of organo‐clay was enough to improve the mechanical properties of PBO. Maximum enhancement in the ultimate tensile strength for PBO hybrids was observed for the blends containing 4% C₁₆‐MMT. The initial modulus monotonically increased with further increases in the C₁₆‐MMT content. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 471–476, 2001     

Poly(lactic acid) nanocomposites with various organoclays. I. Thermomechanical properties,morphology, and gas permeability

The thermomechanical properties, morphology, and gas permeability of hybrids prepared with three types of organoclays were compared in detail. Hexadecylamine–montmorillonite (C₁₆–MMT), dodecyltrimethyl ammonium bromide–montmorillonite (DTA‐MMT), and Cloisite 25A were used as organoclays in the preparation of nanocomposites. From morphological studies using transmission electron microscopy, most clay layers were found to be dispersed homogeneously in the matrix polymer, although some clusters or agglomerated particles were also detected. The initial degradation temperature (at a 2% weight loss) of the poly(lactic acid) (PLA) hybrid films with C₁₆–MMT and Cloisite 25A decreased linearly with an increasing amount of organoclay. For hybrid films, the tensile properties initially increased but then decreased with the introduction of more of the inorganic phase. The O₂ permeability values for all the hybrids for clay loadings up to 10 wt % were less than half the corresponding values for pure PLA, regardless of the organoclay. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 94–103, 2003     

Crystallization behavior and thermal stability of poly(trimethylene terephthalate)/clay nanocomposites

Poly(trimethylene terephthalate) (PTT)/montmorillonite (MMT) nanocomposites were prepared by the solution intercalation method. Two different kinds of clay were organomodified with an intercalation agent of cetyltrimetylammonium chloride (CMC). X‐ray diffraction (XRD) indicated that the layers of MMT were intercalated by CMC, and interlayer spacing was a function of the cationic exchange capacity of clay. The XRD studies demonstrated that the interlayer spacing of organoclay in the nanocomposites depends on the amount of organoclay. From the results of differential scanning calorimetric analysis, it was found that clay behaves as a nucleating agent and enhances the crystallization rate of PTT. The maximum enhancement of the crystallization rate for the nanocomposites was observed in nanocomposites containing about 1 wt % organoclay with a range of 1–15 wt %. From thermogravimetric analysis, we found that the thermal stability of the nanocomposites was enhanced by the addition of 1–10 wt % organoclay. According to transmission electron microscopy, the organoclay particle was highly dispersed in the PTT matrix without a large agglomeration of particles for a low organoclay content (5 wt %). However, an agglomerated structure did form in the PTT matrix at a 15 wt % organoclay content. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2902–2910, 2003     

Synthesis and characterization of organosoluble,thermoplastic elastomer/clay nanocomposites

We synthesized organosoluble, thermoplastic elastomer/clay nanocomposites by making a jelly like solution of ethylene vinyl acetate containing 28% vinyl acetate (EVA‐28) and blending it with organomodified montmorillonite. Sodium montmorillonite (Na⁺‐MMT) was made organophilic by the intercalation of dodecyl ammonium ions. X‐ray diffraction patterns of Na⁺‐MMT and its corresponding organomodified dodecyl ammonium ion intercalated montmorillonite (12Me‐MMT) showed an increase in the interlayer spacing from 11.94 to 15.78 Å. However, X‐ray diffraction patterns of the thermoplastic elastomer and its hybrids with organomodified clay contents up to 6 wt % exhibited the disappearance of basal reflection peaks within an angle range of 3–10°, supporting the formation of a delaminated configuration. A hybrid containing 8 wt % 12Me‐MMT revealed a small hump within an angle range of 5–6° because of the aggregation of silicate layers in the EVA‐28 matrix. A transmission electron microscopy image of the same hybrid showed 3–5‐nm 12Me‐MMT particles dispersed in the thermoplastic elastomer matrix; that is, it led to the formation of nanocomposites or molecular‐level composites with a delaminated configuration. The formation of nanocomposites was reflected through the unexpected improvement of thermal and mechanical properties; for example, the tensile strength of a nanocomposite containing only 4 wt % organophilic clay was doubled in comparison with that of pure EVA‐28, and the thermal stability of the same nanocomposite was higher by about 34 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2065–2072, 2002     

Impact fracture toughness of polyamide‐6/montmorillonite nanocomposites toughened with a maleated styrene/ethylene butylene/styrene elastomer

Polyamide‐6 (PA6)/montmorillonite (MMT) nanocomposites toughened with maleated styrene/ethylene butylene/styrene (SEBS‐g‐MA) were prepared via melt compounding. Before melt intercalation, MMT was treated with an organic surfactant agent. Tensile and impact tests revealed that the PA6/4% MMT nanocomposite fractured in a brittle mode. The effects of SEBS‐g‐MA addition on the static tensile and impact properties of PA6/4% MMT were investigated. The results showed that the SEBS‐g‐MA addition improved the tensile ductility and impact strength of the PA6/4% MMT nanocomposite at the expenses of its tensile strength and stiffness. Accordingly, elastomer toughening represents an attractive route to novel characteristics for brittle clay‐reinforced polymer nanocomposites. The essential work of fracture (EWF) approach under impact drop‐weight conditions was used to evaluate the impact fracture toughness of nanocomposites toughened with an elastomer. Impact EWF measurements indicated that the SEBS‐g‐MA addition increased the fracture toughness of the PA6/4% MMT nanocomposite. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 585–595, 2005     

Polymorphism behavior of poly(ethylene naphthalate)/clay nanocomposites

Thermally stable organically modified clays based on 1,3‐didecyl‐2‐methylimidazolium (IM2C10) and 1‐hexadecyl‐2,3‐dimethyl‐imidazolium (IMC16) were used to prepare poly(ethylene naphthalate) (PEN)/clay nanocomposites via a melt intercalation process. The clay dispersion in the resulting hybrids was studied by a combination of X‐ray diffraction, polarizing optical microscopy, and transmission electron microscopy. It was found that IMC16 provided better compatibility between the PEN matrix and the clay than IM2C10, as evidenced by some intercalation of polymer achieved in the PEN/IMC16‐MMT hybrid. The effects of clay on the crystal structure of PEN were investigated. It was found that both pristine MMT and imidazolium‐treated MMT enhanced the formation of the β‐crystal phase under melt crystallization at 200 °C. At 180 °C, however, the imidazolium‐treated MMT was found to favor the α‐crystal form instead. The difference in clay‐induced polymorphism behavior was attributed to conformational changes experienced by the clay modifiers as the crystallization temperature changes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1040–1049, 2006     

Extruder‐made TPO nanocomposites. II. Effect of maleated poly(propylene)/organoclay ratio on morphology and thermal expansion behavior

Coefficients of linear thermal expansion (CTE) for poly(propylene)/ poly(propylene)‐grafted‐maleic anhydride/montmorillonite ethylene‐co‐octene elastomer (PP/PP‐g‐MA/MMT/EOR) blend nanocomposites were determined as a function of MMT content and various PP‐g‐MA/organoclay masterbatch ratios. The nanocomposites were prepared in a twin‐screw extruder at a fixed 30 wt % elastomer, 0–7 wt % MMT content, and various PP‐g‐MA/organoclay ratio of 0, 0.5, 1.0, and 1.5. The organoclay dispersion facilitated by the maleated PP helps to reduce the size of the dispersed phase elastomer particles in the PP matrix. The elastomer particle size decreased significantly as the PP‐g‐MA/organoclay ratio and MMT content increased; the elastomer particles viewed // to flow direction (FD) are smaller and less deformed compared to those viewed // to transverse direction (TD). The elastomer particle shape based on the view along the three orthogonal directions of the injection molded sample is similar to a prolate ellipsoid. The CTE decreased significantly in the FD and TD, whereas a slight increase is observed in the normal direction in the presence of MMT and PP‐g‐MA. The Chow model based on a two population approach showed better fit to experimental CTE when the effect of MMT and elastomer are considered individually. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B Polym. Phys. 2013 , 51, 952–965     

Polyurethane‐nanocomposite materials via in situ polymerization into organoclay interlayers

New nanocomposite materials based on polyurethane intercalated into organoclay layers have been synthesized via in situ polymerization. The syntheses of polyurethane–organoclay hybrid films were carried out by swelling the organoclay [12‐aminododecanoic acid montmorillonite] into different kinds of diols followed by addition of diisocyanate then casting in a film. The homogeneous dispersion of MMT in the polymer matrix is evidenced by scanning electron microscope and x‐ray diffraction, which showed the disappearance of the peak characteristic to d₀₀₁ spacing. It was found that the presence of organoclay has improved the thermal, solvent resistance and mechanical properties. Also, the tensile strength is increased with increasing the organoclay contents to 20% by the ratio 182% related to the PU with 0% organoclay. On the contrary, the elongation has decreased with increasing the organoclay contents. Copyright © 2007 John Wiley & Sons, Ltd.     

Synthesis and characterization of a series of thermotropic liquid crystalline copolyester nanocomposites

A series of aromatic thermotropic liquid crystalline copolyester (TLCP) nanocomposites were prepared by the in situ intercalation polymerization of p‐acetoxybenzoic acid (ABA), terephthalic acid (TPA), and diacetoxynaphthalene (DAN) isomers in the presence of the organoclay. The DAN isomers used in this study were 2,3‐ and 2,7‐naphthylene. We examined the variation of the liquid crystallinity, morphology, and thermal properties of the nanocomposites with organoclay content in the range 0–10 wt %. All the polymer nanocomposites were fabricated with a molar ratio of ABA:TPA:DAN = 2:1:1; they were shown to consist of a nematic liquid crystalline phase for low organoclay contents (≤5 wt %), whereas the hybrids with a higher concentration of organoclay (≥10 wt %) were found not to be mesomorphic. By using transmission electron microscopy, the clay layers in the 2,3‐DAN copolyester hybrids were found to be better dispersed in the matrix polymer than those in the 2,7‐DAN copolyester hybrids. The introduction of an organoclay into the matrix polymer was found to improve the thermal properties of the 2,3‐DAN copolyester hybrids. However, the thermal properties of the 2,7‐DAN copolyester hybrids were found to be worse than those of the pure matrix polymer for all organoclay compositions tested. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 387–397, 2006     

Preparation of poly(ethylene terephthalate)/organoclay nanocomposites using a polyester ionomer as a compatibilizer

In this work, poly(ethylene terephthalate)/organically modified montmorillonite (PET/o‐MMT) nanocomposites were prepared via direct melt compounding in a twin‐screw extruder. The main objective was to study the effects of using a polyester ionomer (PETi) as a compatibilizer to promote the intercalation and/or exfoliation of the o‐MMT in the PET. The o‐MMT content was 0, 1, 3, or 5 wt % and the PETi/o‐MMT mass ratio was 0/1, 1/1, or 3/1. The PETi was efficient to promote the intercalation/exfoliation of the o‐MMT in the PET matrix, as revealed by wide angle X‐ray scattering and transmission electron microscopy. Rheological characterization showed that the PET/o‐MMT nanocomposites exhibited a higher complex viscosity at low frequencies than PET, which is characteristic of materials presenting yield strength. Moreover, the higher the content and/or the degree of intercalation/exfoliation of the o‐MMT, the more the nanocomposite behaved like a solid because of a percolated structure formed by the o‐MMT layers, and the more the storage and loss modulus, G′ and G″, became independent of the frequency at low frequencies. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3084–3091, 2007     

Structure and properties of poly(ethylene terephthalate)/Na+‐montmorillonite nanocomposites prepared by solid state shear milling (S3M) method

This article reported a novel technology, solid state shear milling (S³M), to prepare poly(ethylene terephthalate)/Na⁺‐montmorillonite nanocomposites using the pristine Na⁺‐MMT without organic modification so as to avoid the problem that the organic modifiers, used for MMT treatment will decompose at high processing temperature of PET, and the structure and properties of the obtained samples were investigated. XRD and TEM analyses showed that Na⁺‐MMT layers were partially delaminated and intercalated, and uniformly dispersed in the PET matrix when suffering from the strong three dimensional shearing forces of pan‐milling. DSC analysis showed that Na⁺‐MMT serves as a nucleating agent, increasing the crystallization rate as well as the crystallization temperature of PET. The properties such as thermal stability and tensile strength of the PET/Na⁺‐MMT nanocomposites prepared by S³M got remarkably improved. Solid state shear milling (S³M) method was a simple and efficient method to get polymer/Na⁺‐MMT nanocomposites with pretty good performances without organic modification of pristine Na⁺‐MMT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 807–817, 2008     

Review of melt‐processed nanocomposites based on EVOH/organoclay

EVOH nanocomposites containing organically treated clays are unique systems in which the clay is strongly attracted to EVOH, thus affecting the morphology and the resultant thermal and mechanical properties. A strong effect of the processing conditions on morphology, thermal, and mechanical properties was observed. In highly interacting systems, under dynamic mixing conditions, in addition to a fracturing process of the clay particles, an onion‐like delamination process is suggested. EVA‐g‐MA and LLDPE‐g‐MA, having polar groups, were studied as compatibilizers to further induce clay intercalation and exfoliation. The compatibilizers affected both the thermal and mechanical properties of the composites at different levels. Thermal analysis showed that with increasing compatibilizer content lower crystallinity levels result, until at a certain content no crystallization has taken place. A Ny‐6 (nylon‐6)/EVOH blend is an interesting host matrix for incorporation of low organoclay contents. The Ny‐6/EVOH blend is a unique system that tends to hydrogen bond and also to in situ chemically react during melt mixing. The addition of clay seems to interrupt the chemical reaction between the two host polymers at certain compositions, leading to lower melt blending torque levels when clay is present. A competition between Ny‐6 and EVOH regarding the intercalation process takes place. However, Ny‐6 seems to lead to exfoliated structures, whereas EVOH forms intercalated structures, as revealed from combined XRD and TEM experiments, owing to thermodynamic considerations and preferential localization of the clay in Ny‐6. Of special interest is the increased storage modulus seen by the presence of only 1 wt % clay, which was achieved by extrusion under high shear forces, leading to a completely exfoliated structure. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1931–1943, 2005     

Fluorene‐based polyester nanocomposites via in situ interlayer polymerization

Fluorene‐based polyester nanocomposites were prepared by in situ polymerization of equivalent weights of 9,9′‐dihexylfluorene‐2,7‐dicarboxylic acid and 4,4′‐dihydroxy‐1,4‐diphenoxybutane (DPB‐OH) in the presence of octadecyl‐montmorillonite (C₁₈‐MMT) as an organoclay. We investigated the intercalation of the organoclay among the polymer chains, with the aim of improving the thermal properties of the polyester. It was found that the addition of only a small amount of organoclay was enough to improve the polyester's thermal properties. The maximum enhancement of the thermal properties of the fluorene‐based polyester nanocomposites was observed with the dispersion of 5 wt% organoclay. Copyright © 2008 John Wiley & Sons, Ltd.     

Factors affecting product distributions in ethylene/styrene copolymerization by (aryloxo)(cyclopentadienyl)titanium complexes‐MAO catalyst systems

Ethylene/styrene copolymerizations using Cp′TiCl₂(O‐2,6‐ⁱPr₂C₆H₃) [Cp′ = Cp* (C₅Me₅, 1 ), 1,2,4‐Me₃C₅H₂ ( 2 ), tert‐BuC₅H₄ ( 3 )]‐MAO catalyst systems were explored under various conditions. Complexes 2 and 3 exhibited both high catalytic activities (activity: 504–6810 kg‐polymer/mol‐Ti h) and efficient styrene incorporations at 25, 40°C (ethylene 6 atm), affording relatively high molecular weight poly (ethylene‐co‐styrene)s with unimodal molecular weight distributions as well as with uniform styrene distributions (M_w = 6.12–13.6 × 10⁴, M_w/M_n = 1.50–1.71, styrene 31.7–51.9 mol %). By‐productions of syndiotactic polystyrene (SPS) were observed, when the copolymerizations by 1 – 3 ‐MAO catalyst systems were performed at 55, 70 °C (ethylene 6 atm, SPS 9.0–68.9 wt %); the ratios of the copolymer/SPS were affected by the polymerization temperature, the [styrene]/[ethylene] feed molar ratios in the reaction mixture, and by both the cyclopentadienyl fragment (Cp′) and anionic ancillary donor ligand (L) in Cp′TiCl₂(L) (L = Cl, O‐2,6‐ⁱPr₂C₆H₃ or N=C^tBu₂) employed. Co‐presence of the catalytically‐active species for both the copolymerization and the homopolymerization was thus suggested even in the presence of ethylene; the ratios were influenced by various factors (catalyst precursors, temperature, styrene/ethylene feed molar ratio, etc.). © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4162–4174, 2008     

Synthesis,rheology, and morphology of nylon‐11/layered silicate nanocomposite

Exfoliated nylon‐11/layered silicate nanocomposites were prepared via in situ polymerization by dispersing organoclay in 11‐aminoundecanoic acid monomer. The original clay was modified by a novel method with 11‐aminoundecanoic acid. In situ Fourier transform infrared spectroscopy results show that stronger hydrogen bonds exist between nylon‐11 and organoclay than that of between nylon‐11 and original clay. The linear dynamic viscoelasticity of organoclay nanocomposites was investigated. Before taking rheological measurements, the exfoliated and intercalating structures and the thermal properties were characterized using X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry, and thermogravimetric analysis. The results show that the clay was uniformly distributed in nylon‐11 matrix during in situ polymerization of clay with 4 wt % or less. The presence of clay in nylon‐11 matrix increased the crystallization temperature and the thermal stability of nanocomposites prepared. Rheological properties such as storage modulus, loss modulus, and relative viscosity have close relationship with the dispersion favorably compatible with the organically modified clay. Comparing with neat nylon‐11, the nanocomposites show much higher dynamic modulus and stronger shear thinning behavior. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2161–2172, 2006     

Thermal gelation or gel melting: (ethylene glycol)113‐(l‐alanine)12 and (ethylene glycol)113‐(l‐lactic acid)12

When PEG (M.W.～5000 Daltons) is conjugated to poly(l ‐alanine), the polymer aqueous solutions (<10.0 wt.%) undergo sol‐to‐gel (thermal gelation), whereas it is conjugated to poly(l ‐lactic acid), the polymer aqueous solutions (>30.0 wt.%) undergo gel‐to‐sol (gel melting) as the temperature increases. In the search for molecular origins of such a quite different phase behavior, poly(ethylene glycol)‐poly(l ‐alanine) (PEG‐PA; EG₁₁₃‐A₁₂) and poly(ethylene glycol)‐poly(l ‐lactic acid) (PEG‐PLA; EG₁₁₃‐LA₁₂) are synthesized and their aqueous solution behavior is investigated. PEG‐PAs with an α‐helical core assemble into micelles with a broad size distribution, and the dehydration of PEG drives the aggregation of the micelles, leading to thermal gelation, whereas increased molecular motion of the PLA core overwhelms the partial dehydration of PEG, thus gel melting of the PEG‐PLA aqueous solutions occurs. The core‐rigidity of micelles must be one of the key factors in determining whether a polymer aqueous solution undergoes sol‐to‐gel or gel‐to‐sol transition, as the temperature increases. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, , 52, 2434–2441     

Nanocomposites of polyurethane with various organoclays: Thermomechanical properties,morphology, and gas permeability*

The properties of polyurethane (PU) nanocomposites with three different organoclays were compared in terms of their thermal stabilities, mechanical properties, morphologies, and gas permeabilities. Hexadecylamine–montmorillonite, dodecyltrimethyl ammonium–montmorillonite, and Cloisite 25A were used as organoclays for making PU hybrid films. The properties were examined as a function of the organoclay content in a matrix polymer. Transmission electron microscopy photographs showed that most clay layers were dispersed homogeneously into the matrix polymer on the nanoscale, although some particles of clay were agglomerated. Moreover, the addition of only a small amount of organoclay was enough to improve the thermal stabilities and mechanical properties of PU hybrid films, whereas gas permeability was reduced. Even polymers with low organoclay contents (3–4 wt %) showed much higher strength and modulus values than pure PU. Gas permeability was reduced linearly with an increasing amount of organoclay in the PU matrix. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 670–677, 2002; DOI 10.1002/polb.10124     

Poly(1‐butene)/clay nanocomposites: Preparation and properties

The preparation and properties of poly(1‐butene) (PB)/clay nanocomposites are described for the first time. Nanocomposites were prepared with the melt‐intercalation technique, using organically modified clay. The X‐ray diffraction patterns portrayed well‐defined diffraction peaks at higher d‐spacing than pristine clay, confirming the intercalation of polymer in silicate layers. Because PB exhibits time‐dependent polymorphism, the effect of clay on the phase transformation of PB was examined with thermal analysis. The phase transformation from a metastable tetragonal form to a stable hexagonal form was enhanced because of incorporation of layered silicates in the polymer matrix. The nanocomposites exhibited about a 40–140% increase in storage modulus depending on the clay content and significantly lower coefficient of thermal expansion. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1014–1021, 2003     

Extruder‐made TPO nanocomposites. I. Effect of maleated polypropylene and organoclay ratio on the morphology and mechanical properties

PP/PP‐g‐MA/MMT/EOR blend nanocomposites were prepared in a twin‐screw extruder at fixed 30 wt % elastomer and 0 to 7 wt % MMT content. Elastomer particle size and shape in the presence of MMT were evaluated at various PP‐g‐MA/organoclay masterbatch ratios of 0, 0.5, 1.0, and 1.5. The organoclay dispersion facilitated by maleated polypropylene serves to reduce the size of the elastomer dispersed phase particles and facilitates toughening of these blend nanocomposites. The rheological data analysis using modified Carreau‐Yasuda model showed maximum yield stress in extruder‐made nanocomposites compared with nanocomposites of reactor‐made TPO. Increasing either MMT content or the PP‐g‐MA/organoclay ratio can drive the elastomer particle size below the critical particle size below which toughness is dramatically increased. The ductile‐brittle transition shift toward lower MMT content as the PP‐g‐MA/organoclay ratio is increased. The D‐B transition temperature also decreased with increased MMT content and masterbatch ratio. Elastomer particle sizes below ～1.0 μm did not lead to further decrease in the D‐B transition temperature. The tensile modulus, yield strength, and elongation at yield improved with increasing MMT content and masterbatch ratio while elongation at break was reduced. The modified Mori‐Tanaka model showed better fit to experimental modulus when the effect of MMT and elastomer are considered individually. Overall, extruder‐made nanocomposites showed balanced properties of PP/PP‐g‐MA/MMT/EOR blend nanocomposites compared with nanocomposites of reactor‐made TPO. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Layered silicate/epoxy nanocomposites: synthesis,characterization and properties

Novel epoxy‐clay nanocomposites have been prepared by epoxy and organoclays. Polyoxypropylene triamine (Jeffamine T‐403), primary polyethertriamine (Jeffamine T‐5000) and three types of polyoxypropylene diamine (Jeffamine D‐230, D‐400, D‐2000) with different molecular weight were used to treat Na‐montmorillonite (MMT) to form organoclays. The preparation involves the ion exchange of Na⁺ in MMT with the organic ammonium group in Jeffamine compounds. X‐ray diffraction (XRD) confirms the intercalation of these organic moieties to form Jeffamine‐MMT intercalates. Jeffamine D‐230 was used as a swelling agent for the organoclay and curing agent. It was established that the d₀₀₁ spacing of MMT in epoxy‐clay nanocomposites depends on the silicate modification. Although XRD data did not show any apparent order of the clay layers in the T5000‐MMT/epoxy nanocomposite, transmission electron microscopy (TEM) revealed the presence of multiplets with an average size of 5 nm and the average spacing between multiplets falls in the range of 100 Å. The multiplets clustered into mineral rich domains with an average size of 140 nm. Scanning electron microscopy (SEM) reveals the absence of mineral aggregate. Nanocomposites exhibit significant increase in thermal stability in comparison to the original epoxy. The effect of the organoclay on the hardness and toughness properties of crosslinked polymer matrix was studied. The hardness of all the resulting materials was enhanced with the inclusion of organoclay. A three‐fold increase in the energy required for breaking the test specimen was found for T5000‐MMT/epoxy containing 7 wt% of organoclay as compared to that of pure epoxy. Copyright © 2004 John Wiley & Sons, Ltd.