Preparation and characterization of PVC/PANI conductive composite with extremely low percolation threshold

Aniline was polymerized in the presence of poly(vinyl chloride) (PVC) powders in hydrochloric acid to in situ prepare poly(vinyl chloride)/polyaniline (PVC/PANI) composite particles. UV‐vis spectra and FT‐IR spectra indicate PANI in PVC/PANI composite particles possessed a higher oxidation state with decreased aniline content in reactants. Both conductivity and impact strength of the dodecylbenzenesulfonic acid (DBSA) doped PANI composites (PVC/PANI‐DBSA), which were compression molded from the in situ prepared PVC/PANI particles, increase with the pressing temperature and decrease with the increase of DBSA doped PANI (PANI‐DBSA) loading. An excellent electric conductivity of 5.06 × 10^?2 S/cm and impact strength of 0.518 KJ/m² could be achieved for the in situ synthesized and subsequently compression molded composite. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and characterization of polyaniline/silicon dioxide composites and preparation of conductive films

The focus of this study was to synthesize the inherently conductive polymer polyaniline using an optimized process to prepare polyaniline/silicon dioxide (PANI/SiO₂) composites by in situ polymerization and ex situ solution mixing. PANI and PANI/SiO₂ composite films were prepared by drop‐by‐drop and spin coating methods. The electrical conductivities of HCl doped PANI film and PANI/SiO₂ composite films were measured according to the standard four‐point‐probe technique. The composite films exhibited an increase in electrical conductivity over neat PANI. PANI and PANI/SiO₂ composites were also investigated by spectroscopic methods including UV‐Vis, FT‐IR, and Photoluminescence. UV‐Vis and FT‐IR studies showed that SiO₂ particles affect the quinoid units along the polymer backbone and indicate strong interactions between the SiO₂ particles and the quinoidal sites of PANI (doping effect). The photoluminescence properties of PANI and PANI/SiO₂ composites were studied and the PANI/SiO₂ composites showed increased intensity as compared to neat PANI. The increase of conductivity of PANI/SiO₂ composite may be partially due to the doping or impurity effect of SiO₂ where the silicon dioxides compete with chloride ions. The morphology of particles and films were examined by a scanning electron microscope (SEM). SEM measurements indicated that the SiO₂ were well dispersed and isolated in composite films. Copyright © 2009 John Wiley & Sons, Ltd.     

Composites of Polystyrene Sulfonic Acid (PSSA)‐Polyaniline and Montmorillonite Clay: Synthesis and Characterization

Polystyrene sulfonic acid (PSSA) doped water‐soluble polyaniline (PANI)/montmorillonite (MMT) clay composites were synthesized by intercalation polymerization in aqueous medium. The properties of the composites were characterized by X‐ray diffraction (XRD), transmission electron microscope (TEM), Fourier‐transform infrared spectroscopy (FT‐IR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X‐ray photoelectron spectroscopy (XPS) and conductivity measurement. The results show that the composite has a mixed nanomorphology and exfoliated silicate nanolayers of MMT clay dispersed in the polyaniline matrix. This composite is more thermal stable than that without clay samples and results in good stable temperature‐dependent dc conductivity [σ_dc(T)] as temperature changed.     

Electrically conductive,melt‐processed ternary blends of polyaniline/dodecylbenzene sulfonic acid,ethylene/vinyl acetate,and low‐density polyethylene

Although polyaniline (PANI) has high conductivity and relatively good environmental and thermal stability and is easily synthesized, the intractability of this intrinsically conducting polymer with a melting procedure prevents extensive applications. This work was designed to process PANI with a melting blend method with current thermoplastic polymers. PANI in an emeraldine base form was plasticized and doped with dodecylbenzene sulfonic acid (DBSA) to prepare a conductive complex (PANI–DBSA). PANI–DBSA, low‐density polyethylene (LDPE), and an ethylene/vinyl acetate copolymer (EVA) were blended in a twin‐rotor mixer. The blending procedure was monitored, including the changes in the temperature, torque moment, and work. As expected, the conductivity of ternary PANI–DBSA/LDPE/EVA was higher by one order of magnitude than that of binary PANI–DBSA/LDPE, and this was attributed to the PANI–DBSA phase being preferentially located in the EVA phase. An investigation of the morphology of the polymer blends with high‐resolution optical microscopy indicated that PANI–DBSA formed a conducting network at a high concentration of PANI–DBSA. The thermal and crystalline properties of the polymer blends were measured with differential scanning calorimetry. The mechanical properties were also measured. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3750–3758, 2004     

Conductive Nanocomposites Based on Cellulose Nanofibrils Coated with Polyaniline-DBSA Via In Situ Polymerization

Summary: Cellulose nanofibrils (CNF) were extracted by acid hydrolysis from cotton microfibrils and nanocomposites with polyaniline doped with dodecyl benzenesulphonic acid (PANI-DBSA) were obtained by in situ polymerization of aniline onto CNF. The ratios between DBSA to aniline and aniline to oxidant were varied in situ and the nanocomposites characterized by four probe DC electrical conductivity, ultraviolet-visible-near infrared (UV-Vis - NIR) and Fourier-transform infrared (FTIR) spectroscopies and X-ray diffraction (XRD). FTIR and UV-Vis/NIR characterization confirmed the polymerization of PANI onto CNF surfaces. Electrical conductivity of about 10⁻¹ S/cm was achieved for the composites; conductivity was mostly independent of DBSA/aniline (between 2 and 4) and aniline/oxidant (between 1 and 5) molar ratios. X-ray patterns of the samples showed crystalline peaks characteristic of cellulose I for CNF samples, and a mixture of both characteristic peaks of PANI and CNF for the nanocomposites. Field emission scanning electron microscopy (FESEM) characterization corroborated the abovementioned results showing that PANI coated the surface of the nanofibrils.     

Thermal stability study of conductive polyaniline/polyimide blend films on their conductivity and ESR measurement

Conductivity stability at thermal environment of conductive polyaniline‐complexes/polyimide (PANI‐complexes/PI) blends, which were doped by camphorsulfonic acid (CSA) and dodecylbenzenesulfonic acid (DBSA), respectively, were investigated by conductivity measurements, electron spin resonance (ESR) spectra, differential and scanning thermometer (DSC). In the conversion process of PANI/Polyamic acid (PAA) to PANI/PI, the blend endeavored some kinds of alteration such as decomplexation of moisture and solvent, dissociation of dopant, crosslinking of PANI chain, and the imidization of PAA chain. PANI‐DBSA/PI showed higher thermal stability of conductivity than PANI‐CSA/PI, and both samples showed nearly linear decay of conductivity with increasing temperature showing greatly enhancement of conductivity stability. When they were exposed at near or over glass transition temperature, the conductivity decay became faster. The conductivity stability at base environment was also higher for PANI‐DBSA/PI due to difficulty in accessing of hydroxyl ion to PANI, which were resulted from dopant. DBSA‐doped blends showed increased polaron mobility and concentration at relatively high temperature, which led to extremely higher conductivity and its stability at high temperature. Copyright © 2002 John Wiley & Sons, Ltd.     

On the structure and electrical conductivity of polyaniline/polystyrene blends prepared by an aqueous‐dispersion blending method

This article describes electrically conductive polymer blends containing polyaniline‐dodecyl benzene sulfonic acid (PANI‐DBSA) dispersed in a polystyrene (PS) matrix or in crosslinked polystyrene (XPS). Melt blending of previously mixed, coagulated, and dried aqueous dispersions of PANI‐DBSA and PS latices lead to high conductivities at extremely low PANI‐DBSA concentrations (∼0.5 wt % PANI‐DBSA). In these blends, the very small size of the PANI‐DBSA particles and the surface properties (with surfactants used) of both the PANI and polymer particles play a major role in the PANI‐DBSA particle structuring process. The PANI‐DBSA behavior is characteristic of a unique colloidal polymeric filler with an extremely high surface area and a strong interaction with the matrix, evidenced by a significantly higher glass‐transition temperature of the matrix. The effect of the shear level on the conductivity and morphology of the PS/PANI‐DBSA blends was studied by the production of capillary rheometer filaments at various shear rates. An outstanding result was found for XPS/PANI‐DBSA blends prepared by the blending of aqueous XPS and PANI‐DBSA dispersions. Some of these blends were insulating at low shear levels; however, above a certain shear level, smooth surface filaments were generated, with dramatically increased and stable conductivities. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 611–621, 2001     

Polyurethane/polyaniline and polyurethane‐poly(methyl methacrylate)/polyaniline conductive core‐shell particles: Preparation,morphology, and conductivity

Polyurethane/polyaniline (PU/PANI) and polyurethane‐poly(methyl methacrylate)/polyaniline (PU‐PMMA/PANI) conductive core‐shell particles were synthesized by a two‐stage polymerization process. The first stage was to produce a core of PU or PU‐PMMA via miniemulsion polymerization using sodium dodecyl sulfate (SDS) as the surfactant. The second stage was to synthesize the shell of polyaniline over the surface of core particles. Hydrogen chloride (HCl) and dodecyl benzenesulfonic acid (DBSA) were used as the dopant agents. Ammonium persulfate (APS) was used as the oxidant for the polymerization of ANI. Different concentrations of HCl, DBSA, and SDS would cause different conformations of PANI chains and thus different morphologies of PANI particles. UV–visible spectra revealed that the polaron band was blue‐shifted because of the more coiled conformation of PANI chains by increasing the concentration of DBSA. Besides, with a high concentration of DBSA, both spherical‐ and rod‐shape PANI particles were observed by transmission electron microscope, and the coverage of PANI particles onto the core surfaces was improved. The key point of formation of rod‐type PANI particles was that DBSA was served with a high concentration accompanied with the existence of HCl or SDS. The better coverage of PANI particles over the core surfaces by charging higher DBSA concentrations resulted in a higher conductivity of hybrid particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3902–3911, 2007     

掺杂态聚苯胺LB膜的制备与性质

掺杂樟脑磺酸的聚苯胺在纯水表面可以形成稳定的单分子层,采用Ｌａｎｇｍｕｉｒ－Ｂｌｏｄｇｅｔｔ技术可以将其较好地转移到氟化 基片上制成薄膜,对其ＬＢ膜的红外和紫外－可见－近红外光谱研究表明,在膜的压缩或转移过程中有少量的樟脑磺酸分子发生脱掺杂的现象,并且该ＬＢ膜在室温下对乙醇有较好的气敏性。     

Electrospun Polyaniline/Poly(ethylene oxide) Composite Nanofibers Based Gas Sensor

Camphor‐10‐sulfonic acid (HCSA) doped polyaniline (PANI)/poly(ethylene oxide) (PEO) composite nanofibers with different compositions (12 to 52 wt.% of PANI) were synthesized by an electrospinning method and their properties including optical, electrical and sensing were systematically investigated. FT‐IR shows that an increase of IR absorbance ratios of aromatic C? C stretching vibration of benzenoid rings of PANI to C? O? C symmetric vibrational modes of PEO confirmed that the PANI content in nanofiber mats increased proportionally with increase in PANI content in electrospinning solution. The band gap of PANI was determined to be 2.5 eV using UV‐Vis spectroscopy. The electrical conductivities of the nanofibers increased with an increase in the PANI content in the nanofibers. Additionally, the sensitivity toward NH₃ increased as the PANI content increased, but branched nanofibers reduced sensing response. The humidity sensitivity changed from positive to negative as the PANI content increased. The electron transport mechanism was studied by measuring the temperature dependence electrical resistivity. The negative temperature coefficient of resistance revealed a semiconducting behavior for the PANI/PEO nanofibers. The activation energy, calculated by Arrhenius plot, increased as the PANI content decreased. The power law indicated that electrons were being transported in a three dimensional matrix, and the longer hopping distance required more hopping energy for electron transport.     

Effect of aniline formaldehyde resin on the conjugation length and structure of doped polyaniline: Spectral studies

A DBSA (n‐dodecylbenzene sulfate)‐complexed aniline formaldehyde [AF(DBSA)_1.0] was successfully synthesized with excess aniline (compared with formaldehyde) in the presence of n‐dodecylbenzene sulfonic acid (HDBSA), which was complexed with aniline monomer before polymerization. The resin was carefully characterized with ¹H and ¹³C NMR, electron spectroscopy for chemical analysis, and Fourier transform infrared and was demonstrated to be a polymer in which anilines were all complexed with HDBSA and became anilinium salts. A drastic decrease of the maximum absorption wavelength (ultraviolet–visible spectra) of DBSA‐doped polyaniline [PANI(DBSA)_0.5] was found when AF(DBSA)_1.0 was mixed, and this resulted from the reduced conjugation length. A similar effect on PANI(DBSA)_0.5 was found when free HDBSAs were mixed with PANI(DBSA)_0.5. Visual inspection with an optical microscope revealed that PANI(DBSA)_0.5/AF(DBSA)_1.0 gave uniform morphologies in various compositions, showing possible miscibility for this system. X‐ray diffraction patterns of PANI(DBSA)_0.5/AF(DBSA)_1.0 showed that the layered structure of PANI(DBSA)_0.5 was still present but became shorter in the polyblend because of the presence of AF(DBSA)_1.0. Solid‐state ¹³C NMR spectra revealed that the reduced conjugation length was derived from the interaction of alkyl groups between HDBSA, complexed DBSA, and dopant DBSAs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3116–3125, 2005     

A study on the synthesis,characterization and properties of polyaniline using acrylic acid as a primary dopant. I: polymerization and polymer

In the presence of acrylic acid (AA) as a primary dopant, polyaniline (PANI) doped with poly(acrylic acid) was successfully synthesized by using ammonium persulfate (APS) as initiator and oxidizing agent. The effect of experimental conditions on the polymer yields was systematically studied. It was found that the polymer yield can be as high as 65%, and this value strongly depends on synthesis conditions, such as the reaction time, the molar ratio of oxidizing agent to aniline monomer, the concentration of reactants and reaction temperature. The molecular weight ( ) of main chains of the de‐doped PANI is estimated to be 32,000–53,000. Based on the data of FT‐IR, UV‐vis, ¹³C‐nuclear magnetic resonance (NMR), elemental analysis and electrical conductivity measurement, the emeraldine salt form of PANI was confirmed and the molecular structure of the resulting PANI‐AA was proposed. Accordingly the reaction mechanism was discussed and it was convinced that the polymerization reaction of AA is initiated by APS. Copyright © 2004 John Wiley & Sons, Ltd.     

Synthesis and Characterization of Conducting Polyaniline Doped with Polymeric Acids

Conducting polyaniline doped with polymeric acids was synthesized by a in situ chemical polymerization method. The synthesized polymers were characterized by using UV‐Visible, FT‐IR spectroscopy and SEM analysis. Thermal stability of these polymers was evaluated by using TGA/DSC analysis. Among the three polymeric acids used for doping purpose, poly(vinyl sulphonic acid) doped polyaniline is found to be more conducting than those doped with other acids. From the temperature dependent conductivity measurements, an increase in conductivity with increase in temperature was observed.     

Calorimetric investigations of high density polyethylene/polyaniline composites

Summary Electrically conductive composites containing high density polyethylene (HDPE) and polyaniline (PANI) - dodecylbenzenesulfonic acid (DBSA) complex were prepared in situ by bulk oxidative polymerization of aniline (ANI) in presence of DBSA. Their thermal behaviour and crystallinity parameters were studied for the first time by using differential scanning calorimetry (DSC). It was found that the presence of the conductive complex does not affect the crystalline structure of the matrix polymer neither during in situ polymerization of ANI in powdered HDPE nor upon heating of HDPE/PANI·DBSA composite up to 180°C followed by fast cooling.     

乳液聚合中聚苯胺膜形成的动力学研究

以(NH4)2S2O8(APS)为氧化剂,十二烷基苯磺酸(DBSA)同时为乳化剂和掺杂剂,采用乳液聚合方法制备聚苯胺膜(PANIfilm),用石英晶体微天平(QCM)实时监测聚苯胺膜的形成过程,并对其动力学过程进行研究.结果表明,聚苯胺成膜反应对APS是0.5级,对苯胺是1级,聚苯胺膜增长速率随温度的升高而增加,而聚苯胺膜的最终沉积量却减小,表观活化能Ea=41.15kJ/mol,与均相溶液聚合成膜法的结果相近;随着DBSA浓度的增加,聚苯胺膜增长速率减小,而最终的沉积量增大.     

新型水溶性大π共轭高分子——聚吡咯｛2,5-[双(对二甲氨基苯甲烯)]｝的合成

该研究合成了一种新型水溶性大π共轭高分子———聚吡咯 ｛２ ,５ ［ 二（ 对二甲氨基苯甲烯）］｝（ＰＰＤＭＡＢ） ,它能溶于强酸的水溶液,在１ｍｏｌ／Ｌ 的盐酸中溶解度为０－５ ～１－０ｇ／１００ｍＬ．通过ＥＡ、ＸＰＳ、ＦＴ ＩＲ、ＵＶ Ｖｉｓ ＮＩＲ、Ｉｎ ｓｉｔｕ ＵＶ Ｖｉｓ ＮＩＲ 对ＰＰＤＭＡＢ进行了结构表征．通过质子化、碘掺杂、浓硫酸（９８ ％ ） 掺杂等处理,ＰＰＤＭＡＢ的电导率提高２～４ 个数量级（δ＝ １０ － ７ ～１０－ ５Ｓ／ｃｍ） ．在质子化、去质子化的过程中ＰＰＤＭＡＢ发生了可逆的颜色变化,本征态（ 综色） 质子态（ 墨兰色） ．     

Inkjet printable polyaniline nanoformulations

Aqueous polyaniline (PANI) nanodispersions doped with dodecylbenzenesulfonic acid (DBSA) were synthesized and successfully inkjet-printed using a piezoelectric desktop printer. This paper examines the optimization and characterization of the nanoparticulate formulation for optimal film electrochemistry and stability. PANI nanoparticle synthesis was optimized in terms of the ratio of monomer (aniline) to oxidant (ammonium persulphate, APS) and dopant (DBSA). Particle size, UV-vis spectroscopy, electrochemical, and conductivity analyses were performed on all materials. Optimal synthesis conditions were found to be at a molar ratio of 1.0:0.5:1.2 aniline/APS/DBSA. This resulting nanodispersion showed a uniform particle size distribution of approximately 82 nm, and UV-vis analysis indicated a high doping level. These synthetic conditions resulted in the highest conductivity, and the electrochemistry of the resulting films was well-defined and stable. Surface tension analysis and rheological studies demonstrated that the aqueous nanodispersions were suitable for inkjet printing. Successful inkjet printing of these polyaniline nanoparticulate formulations is demonstrated.     

PI/PANI复合材料的制备与表征

以纳米聚苯胺为电磁波的吸收剂,高强度、耐高温的聚酰亚胺为基体设计与制备了高强度、耐热、质轻、薄和吸收宽的新型纳米复合吸波材料.利用微乳液法,以十二烷基苯磺酸(DBSA)为乳化剂和掺杂剂,以过硫酸铵(APS)为氧化剂合成了纳米级聚苯胺(PANI).在此基础上,以PANI的NMP溶液为均苯四甲酸二酐(PMDA)与4,4′-二氨基二苯醚(ODA)的聚合场所,室温下,原位聚合出PANI/聚酰胺酸(PAA)复合材料,再经过亚胺化制备出了PANI/PI复合材料.利用XRD表征了聚合物的结晶形态.红外光谱表征了中间体和聚合物.利用场发射扫描电镜发现PANI/PI复合材料呈现海岛结构,PANI像岛屿一样分散在PI的连续相中,两种材料复合并没有破坏各自的结晶形态.利用数字电桥和自制电极表征了不同含量复合材料的损耗性能,当聚苯胺加到3.4%以上时,复合材料的损耗因数提高了,并且随着频率的增大损耗因数直线增大.     

Electrical properties and EMI shielding behavior of highly thermally stable polyaniline/colloidal graphite composites

A hybrid approach has been adopted by using a combination of colloidal graphite (CG) as a conducting filler, 5‐lithium sulfoisophthalic (LiSIPA) acid as a dopant, and polyaniline (PANI) as a matrix to prepare LiSIPA doped PANI–CG composites. The thermal stability (～300°C) and electrical conductivity (67.4 S/cm at 17.4% CG content) have been improved significantly as compared to PANI doped with conventional inorganic dopants like HCl or H₂SO₄ (130–150°C). The maximum shielding effectiveness value was found to be ?39.7 dB. X‐ray diffraction and infrared spectroscopy showed a systematic shifting of the characteristic peaks and bands with increase in the amount of CG, which indicates significant interaction exists between CG and PANI. The UV–Vis spectra showed the characteristic bands of PANI, with a shift to shorter wavelength with increase in the CG content. The interaction mechanism between doped PANI and CG in the resultant composites has been proposed. Copyright © 2009 John Wiley & Sons, Ltd.     

Synthesis and characterization of polyaniline nanoparticles in phosphonic acid amphiphile aqueous micellar solutions for waterborne corrosion protection coatings

Polyaniline (PANI) dispersions consisting of 270 to 380 nm sized particles were prepared by oxidation with ammonium peroxydisulfate (APS) in n‐decylphosphonic acid (DPA) micellar solutions. The green dispersions do not undergo macroscopic precipitation for more than a year. The synthesized DPA doped PANI exhibited enhanced electrical conductivity (3.6 S cm^?1 ) compared with DPA‐PANI (2.3 x 10 ^{? 4} S cm ^{? 1}) prepared by postsynthesis treatment of the PANI‐base with DPA. It was shown that through protonation with decylphosphonic acid, polyaniline showed a significantly enhanced solubility in common organic solvents like chloroform, xylene, etc. The synthesized PANI was characterized by intrinsic viscosity, solubility, FT‐IR , conductivity, SEM , and TGA measurements. The wide‐angle X ‐ray diffraction study revealed the appearance of a peak located at low angles (d = 29.4 – 35.3 Å) suggesting the formation of layered structure of PANI backbone separated by long alkyl side chains of DPA. The anticorrosive performance of the bilayer coatings composed of a bottom layer of DPA doped polyaniline covered with a polyvinyl butyral topcoat, have been demonstrated for steel exposed to neutral saline solutions. It was found that the inhibitive properties of DPA dopant provides further protection to the base metal through smart release when damage is produced on the surface of the coating. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1606–1616