Reaction thermodynamics of amine‐cured epoxy systems: Validation of the enthalpy and heat capacity of reaction as determined by modulated temperature differential scanning calorimetry

The reaction enthalpy and reaction heat capacity of three aromatic epoxy–amine systems have been determined with modulated temperature diffential scanning calorimetry (MTDSC), mostly in quasi‐isothermal conditions, over a wide temperature range (33–140 °C) and for different mixture compositions. The reaction enthalpy is only slightly dependent on the epoxy–amine chemistry, from ?111 to ?98 kJ/mol epoxy functionality. With the model system phenyl glycidyl ether (PGE)+aniline, the reaction enthalpy of the secondary amine–epoxy reaction step is equal to that of the primary amine–epoxy reaction. Group contributions needed to calculate the reaction heat capacity with an additivity approach are evaluated, and a new value of 37.2 J mol^?1 K^?1 for the group N? (H)(C)(CB) is proposed. With this group contribution, the additivity method predicts almost equal values for the reaction heat capacity of both amine–epoxy reaction steps at 298.15 K (Δ_rC_p,prim = 15.7 J mol^?1 K^?1 and Δ_rC_p,sec = 14.6 J mol^?1 K^?1), whereas the experimental value of Δ_rC_p,sec is about three times larger than that of Δ_rC_p,prim at 100 °C. These results are confirmed experimentally for PGE+aniline as a different temperature dependence of both reaction heat capacities. MTDSC therefore is potentially interesting for differentiating between reactive species in an epoxy–amine reaction, a benefit previously assigned to spectroscopic methods only. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 594–608, 2003     

Epoxy resin/poly(ϵ‐caprolactone) blends cured with 2,2‐bis[4‐(4‐aminophenoxy)phenyl]propane. I. Miscibility and crystallization kinetics

Crystalline thermosetting blends composed of 2,2′‐bis[4‐(4‐aminophenoxy)phenyl]propane (BAPP)‐cured epoxy resin (ER) and poly(?‐caprolactone) (PCL) were prepared via the in situ curing reaction of epoxy monomers in the presence of PCL, which started from initially homogeneous mixtures of diglycidyl ether of bisphenol A (DGEBA), BAPP, and PCL. The miscibility of the blends after and before the curing reaction was established with differential scanning calorimetry and dynamic mechanical analysis. Single and composition‐dependent glass‐transition temperatures (T_g's) were observed in the entire blend composition after and before the crosslinking reaction. The experimental T_g's were in good agreement with the prediction by the Fox and Gordon–Taylor equations. The curing reaction caused a considerable increase in the overall crystallization rate and dramatically influenced the mechanism of nucleation and the growth of the PCL crystals. The equilibrium melting point depression was observed for the blends. An analysis of the kinetic data according to the Hoffman–Lauritzen crystallization kinetic theory showed that with an increasing amorphous content, the surface energy of the extremity surfaces increased dramatically for DGEBA/PCL blends but decreased for ER/PCL blends. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1085–1098, 2003     

On the polymerisation of the epoxidised biodiesel: The importance of the epoxy rings position,the process and the products

Polyesters were prepared using epoxidised methyl esters of oleic acid (EP_OAME) and epoxidised biodiesel (mixture of methyl esters) from sunflower oil (EP_SOME) and linseed oil (EP_LOME) with cis-1,2-cyclohexanedicarboxylic anhydride and triethylamine. The kinetic of partial processes involved in the polymerisation were elucidated and related to epoxy rings position in the fatty acid chain. The activation energies (E_a) for the epoxy ring opening by the catalyst are 298, 216 and 136 kJ/mol for EP_OAME, EP_SOME and EP_LOME respectively. The reactions of the epoxy rings in the positions C9–C10, C12–C13 and C15–C16 with anhydride require average activation energies of 116, 32 and 22 kJ/mol, respectively. The compensation effect between activation energy and pre-exponential factor is observed. The polymerisation enthalpy, molecular weight, glass transition temperature and electrical properties were determined. The polyesters studied show promising properties for use in various technological applications.     

Curing kinetics and mechanism of bisphenol S epoxy resin with 4,4′‐Diaminodiphenyl ether or phathlic anhydride

The kinetics of the cure reaction for systems of bisphenol‐S epoxy resin with 4,4′‐diaminodiphenyl ether or phthalic anhydride as a curing agent were investigated with a differential scanning calorimetry. Autocatalytic behavior was shown in the first stages of the cure for the systems, which could be well described by the model proposed by Kamal [Polym Eng Sci 1973, 13, 59–64] that includes two rate constants k₁ and k₂ and two reaction orders, m and n. k₁ and k₂ values are observed to increase with the increasing temperature. With the proceeding of the cure reaction, the cross‐linking structure appears, and the reaction is mainly controlled by diffusion in the latter stages. The molecular mechanism of the curing system was discussed. © 2001 John Wiley & Sons, Inc. Int J Chem Kinet 33: 558–563, 2001     

Studies on curing kinetics of a novel combined liquid crystalline epoxy containing tetramethylbiphenyl and aromatic ester‐type mesogenic group with diaminodiphenylsulfone

The curing kinetics of a novel liquid crystalline epoxy resin with combining biphenyl and aromatic ester‐type mesogenic unit, diglycidyl ether of 4,4′‐bis(4‐hydroxybenzoyloxy)‐3,3′,5,5′‐tetramethyl biphenyl (DGE‐BHBTMBP), and the curing agent diaminodiphenylsulfone (DDS) was studied using the advanced isoconvensional method (AICM). DGE‐BHBTMBP/DDS curing system was investigated the curing behavior by means of differential scanning calorimetry (DSC) during isothermal and nonisothermal processes. Only one exothermal peak appeared in isothermal DSC curves. A variation of the effective activation energy with the extent of conversion was obtained by AICM. Three different curing stages were confirmed. In the initial curing stage, the value of E_a is dramatically decreased from ～90 to ～20 kJ/mol in the conversion region 0–0.2 for the formation of LC phase. In the middle stage, the value of E_a keeps about ～80 kJ/mol for cooperative effect of reaction mechanism and diffusion control. In the final stage, a significant increase of E_a from 84 to 136 kJ/mol could be caused by the mobility of longer polymer chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3922–3928, 2007     

Kinetics and mechanistic investigation of epoxy–anhydride compositions cured with quaternary phosphonium salts as accelerators

Mechanism and curing kinetics of bisphenol A epoxy resin–iso‐methyltetrahydrophthalic anhydride compositions using quaternary phosphonium salts as accelerators were investigated by differential scanning calorimetry (DSC) and electrospray mass‐spectrometry (ESI‐MS). The DSC method was applied to investigate curing kinetics and apparent activation energy values for the overall curing process. The DSC results showed that some of the phosphonium salts lead to a lower activation energy, that means they are more effective accelerators for the curing of epoxy–anhydride systems. The mechanism of curing was studied by ESI‐MS using the model reaction of epichlorohydrin (E) with phthalic anhydride (PA) in the presence of phosphonium salts or 2‐methylimidazole. Products containing the alkyl moiety of the phosphonium salt in form of alkyl esters could be identified. This suggests that the phosphonium salts activate the anhydride by electrophilic attack. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1088–1097     

Branching by reactive end groups. III. Synthesis,branching, and analysis of m‐ethynylphenol/p‐t‐butylphenol‐coterminated bisphenol a polycarbonates

The use of m‐ethynylphenol (m‐EP) and p‐t‐butylphenol (PTBP) as coterminators for bisphenol A polycarbonates (BA PCs) provided long‐chain‐branched PCs, partially crosslinked PCs, or both after the thermal reaction of the terminal m‐EP groups, depending on the molar ratio of the chain terminators. Linear m‐EP/PTBP PCs were prepared by solution phosgenation of BA and the two coterminators. Differential scanning calorimetry showed the onset of the m‐EP‐end‐group reaction at about 250 °C by the appearance of a reaction exotherm. The enthalpy (ΔH) of this reaction was roughly proportional to the amount of m‐EP in the PC and to an extent could be used to monitor the progress of the reaction and estimate its kinetics. A complete m‐EP‐end‐group reaction was evident from gel permeation chromatography analysis upon heating under N₂ to 380 °C for 10 min or 360 °C for 60 min. The amount, if any, of gel formed after the m‐EP‐end‐group reaction depended on X_EP; those PCs with a X_EP value less than or equal to 0.33 had little or no gel. The maximum X_EP that precluded the formation of gels after branching was estimated to be about 0.45–0.48. The molecular weight of m‐EP/PTBP PCs increased after branching, as evidenced by gel permeation chromatography analysis. Assuming that the terminal m‐EP groups had a statistical distribution on the polymer chain ends and that they underwent only homopolymerization, the average reacted m‐EP‐group functionality according to estimated gel‐point composition was about 2.8–3.0. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2352–2358, 2000     

Comprehensive 2D NMR analysis: Acrylonitrile/ethyl methacrylate copolymers synthesized by ATRP at ambient temperature

Copolymerization of acrylonitrile and ethyl methacrylate using atom transfer radical polymerization (ATRP) at ambient temperature was carried out under optimized reaction conditions using 2‐bromopropionitrile as initiator and CuBr/2,2′‐bipyridine as the catalyst system. The copolymer composition, obtained from ¹H NMR spectra, were used to determine the monomer reactivity ratios (r_A = 0.68 and r_E = 1.75) involved in ATRP. Two‐dimensional NMR (heteronuclear single quantum correlation and total correlated spectroscopy) experiments were employed to resolve the highly overlapping and complex ¹H and ¹³C{¹H} NMR spectra of copolymers. The complete spectral assignments of the quaternary carbons viz. carbonyl and nitrile carbons were done with the help of heteronuclear multiple bond correlation spectra. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2955–2971, 2006     

Study of cure kinetics of epoxy/DDS/nanosized (SiO2/TiO2) system by dynamic differential scanning calorimetry

In this study the curing kinetics of epoxy based on the diglycidyl ether of bisphenol A (DGEBA), 4,4′‐diaminodiphenyl sulfone (DDS) as a hardener, and SiO₂/TiO₂ (70:30) as a nanofiller was investigated by nonisothermal differential scanning calorimetry (DSC). The effects of different weight contents of SiO₂/TiO₂ nanoparticles were studied using DSC in Dynamic Mode and the best value of the nanofiller was found to be 5 phr (parts per hundred). Dynamic measurements were used to obtain the total heat of reaction of the epoxy system as well as its activation energy (E_a) based on the isoconversional methods of Kissinger and Ozawa. The process revealed a dependence of the activation energy on conversion (α). The morphology of the cured system was investigated by scanning electron microscopy (SEM). It showed a strong cross‐linking between the resin and hardner and a relatively better dispersion of surface modified filler nanoparticles. Copyright © 2009 John Wiley & Sons, Ltd.     

Calorimetric studies on an anhydride‐cured epoxy resin from diglycidyl ether of bisphenol‐A and diglycidyl ether of poly(propylene glycol). I. Onset of diffusion control during isothermal polymerization

Calorimetric studies on a series of anhydride‐cured epoxy resins, in which the epoxy oligomer is a mixture of diglycidyl ether of bisphenol‐A (DGEBA) and diglycidyl ether of poly(propylene glycol) (DGEPPG) in different mole ratios, were carried out. DGEPPG is a flexible epoxy oligomer that was used to tune glass transition temperature for the fully reacted epoxy resin. Conversion versus time curves for the systems with different DGEBA/DGEPPG mole ratios (not including the neat DGEPPG system) were found to overlap with each other in mass‐controlled reaction regime, indicating similar reactivities of epoxy groups in both epoxy oligomers. Onset of diffusion‐controlled reaction regime for different systems was estimated by fitting the conversion versus time data using a phenomenological kinetic equation, as well as from direct comparison of the conversion versus time curves. For the systems (i.e., 0, 10, and 30% DGEPPG) that vitrify during reaction, the crossover from mass‐controlled to diffusion‐controlled reaction occurs close to the onset of the vitrification, where T_g is about 25–30 K below the reaction temperature. For the system (i.e., 50% DGEPPG system) that does not vitrify during the reaction, such crossover still occurs when the T_g of the mixture reaches a value about 25 K below the reaction temperature. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2155–2165, 2008     

Isothermal cure kinetics of epoxy/phenol‐novolac resin blend system initiated by cationic latent thermal catalyst

The investigation of the cure kinetics of a diglycidyl ether of bisphenol A (DGEBA)/phenol‐novolac blend system with different phenolic contents initiated by a cationic latent thermal catalyst [N‐benzylpyrazinium hexafluoroantimonate (BPH)] was performed by means of the analysis of isothermal experiments using a differential scanning calorimetry (DSC). Latent properties were investigated by measuring the conversion as a function of curing temperature using a dynamic DSC method. The results indicated that the BPH in this system for cure is a significant thermal latent initiator and has good latent thermal properties. The cure reaction of the blend system using BPH as a curing agent was strongly dependent on the cure temperature and proceeded through an autocatalytic kinetic mechanism that was accelerated by the hydroxyl group produced through the reaction between DGEBA and BPH. At a specific conversion region, once vitrification took place, the cure reaction of the epoxy/phenol‐novolac/BPH blend system was controlled by a diffusion‐control cure reaction rather than by an autocatalytic reaction. The kinetic constants k₁ and k₂ and the cure activation energies E₁ and E₂ obtained by the Arrhenius temperature dependence equation of the epoxy/phenol‐novolac/BPH blend system were mainly discussed as increasing the content of the phenol‐novolac resin to the epoxy neat resin. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2945–2956, 2000     

Thermodynamic characteristics of poly(cyclohexylethylene‐b‐ethylene‐co‐ethylethylene) block copolymers

A series of poly(cyclohexylethylene‐b‐ethylene‐co‐ethylethylene) (C‐E/E_E) diblock copolymers containing approximately 50% by volume glassy C blocks and varying fraction (x) of E_E repeat units, 0.07 ≤ x ≤ 0.90, was synthesized by anionic polymerization and catalytic hydrogenation. The effects of ethyl branch content on the melt state segment–segment (χ) interaction parameter and soft (E/E_E) block crystallinity were studied. The percent crystallinity ranged from approximately 30% at x = 0.07 to 0% at about x ≥ 0.30, while the melting temperature changed from 101 °C at x = 0.07 to 44 °C at x = 0.28. Dynamic mechanical spectroscopy was employed to determine the order–disorder transition (ODT) temperatures, from which χ was calculated assuming the mean‐field prediction (χN_n)_ODT = 10.5. Previously published results for the temperature dependent binary interaction parameters for C‐E (x = 0.07), C‐E_E (x = 0.90), and E‐E_E (x = 0.07 and x = 0.90) fail to account for the quantitative x dependence of χ, based on a simple binary interaction model. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 566–574, 2010     

Synthesis of polymers by template polymerization. I. Template polymerization of poly(methacrylic acid) with β‐cyclodextrin

A novel template monomer with multiple methacryloyl groups was synthesized with β‐cyclodextrin by the acetylation of primary hydroxyl groups and the esterification of secondary hydroxyl groups with methacrylic acid anhydride. The average number of methacryloyl groups in the monomer was 11. The radical polymerization of the monomer was carried out with the following initiators: α,α′‐azobisisobutylonitrile, H₂O₂? Fe²⁺ redox initiator, p‐xylyl‐N,N‐dimethyldithiocarbamate (XDC), and α‐bromo‐p‐xylyl‐N,N‐dimethyldithiocarbamate (BXDC). When the concentration of the monomer was less than 4.12 × 10^?3 M, polymerization was limited inside the molecule, and gelation of the system was hindered. For controlled radical photopolymerization with XDC and BXDC, the methacryloyl groups of the monomer were homogeneously polymerized, and poly(methacrylic acid) with a narrow molecular weight distribution was obtained by the hydrolysis of the polymerized products. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3539–3546, 2001     

Cure behavior of diglycidylether of bisphenol A/trimethylolpropane triglycidylether epoxy blends initiated by thermal latent catalyst

Cure behaviors of diglycidylether of bisphenol A (DGEBA)/trimethylolpropane triglycidylether (TMP) epoxy blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate (BPH) as a cationic latent catalyst were investigated using DSC and rheometer. This system showed more than one type of reaction and BPH could be excellent thermal latent catalyst without any co‐initiator. The cure activation energy (E_a) obtained from Kissinger method using dynamic DSC data was higher in DGEBA/TMP mixtures than in pure DGEBA. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. The gel time was obtained from the analysis of storage modulus (G′), loss modulus (G″) and damping factor (tanδ). The crosslinking activation energy (E_c) was also determined from the Arrhenius equation based on the gel time and curing temperature. As a result, the crosslinking activation energy showed a similar behavior with that obtained from Kissinger method. And the gel time decreased with increasing TMP content, which could be resulted from increasing the activated sites by trifunctional epoxide groups and decreasing the viscosity of DGEBA/TMP epoxy blend in the presence of TMP. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2114–2123, 2000     

Structural and mechanical behavior of polypropylene/ maleated styrene‐(ethylene‐co‐butylene)‐styrene/sisal fiber composites prepared by injection molding

Hybrid composites consisting of isotactic poly(propylene) (PP), sisal fiber (SF), and maleic anhydride grafted styrene‐(ethylene‐co‐butylene)‐styrene copolymer (MA‐SEBS) were prepared by melt compounding, followed by injection molding. The melt‐compounding torque behavior, thermal properties, morphology, crystal structure, and mechanical behavior of the PP/MA‐SEBS/SF composites were systematically investigated. The torque test, thermogravimetric analysis, differential scanning calorimetric, and scanning electron microscopic results all indicated that MA‐SEBS was an effective compatibilizer for the PP/SF composites, and there was a synergism between MA‐SEBS and PP/SF in the thermal stability of the PP/MA‐SEBS/SF composites. Wide‐angle X‐ray diffraction analysis indicated that the α form and β form of the PP crystals coexisted in the PP/MA‐SEBS/SF composites. With the incorporation of MA‐SEBS, the relative amount of β‐form PP crystals decreased significantly. Mechanical tests showed that the tensile strength and impact toughness of the PP/SF composites were generally improved by the incorporation of MA‐SEBS. The instrumented drop‐weight dart‐impact test was also used to examine the impact‐fracture behavior of these composites. The results revealed that the maximum impact force (F_max), impact‐fracture energy (E_T), total impact duration (t_r), crack‐initiation time (t_init), and crack‐propagation time (t_prop) of the composites all tended to increase with an increasing MA‐SEBS content. From these results, the incorporation of MA‐SEBS into PP/SF composites can retard both the crack initiation and propagation phases of the impact‐fracture process. These prolonged the crack initiation and propagation time and increased the energy consumption during impact fracture, thereby leading to toughening of PP/MA‐SEBS/SF composites. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1214–1222, 2002     

Syntheses and properties of organosoluble poly(ether imide)s from 1,1‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]cyclohexane dianhydride and aromatic diamines

A bis(ether anhydride) monomer, 1,1‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]cyclohexane dianhydride ( IV‐A ), was synthesized from the nitro displacement of 4‐nitrophthalodinitrile by the phenoxide ion of 1,1‐bis(4‐hydroxyphenyl)cyclohexane ( I‐A ), followed by alkaline hydrolysis of the intermediate bis(ether dinitrile) and dehydration of the resulting bis(ether acid). A novel series of organosoluble poly(ether imide)s ( VI _a–i )(PEIs) bearing cyclohexylidene cardo groups was prepared from the bis(ether anhydride) IV‐A with various aromatic diamines V _a–i via a conventional two‐stage process. The PEIs had inherent viscosities in the range of 0.48–1.02 dL/g and afforded flexible and tough films by solution‐casting because of their good solubilities in organic solvents. Most PEIs showed yield points in the range of 89–102 MPa at stress‐strain curves and had tensile strengths of 78–103 MPa, elongations at breaks of 8–62%, and initial moduli of 1.8–2.2 GPa. The glass‐transition temperatures (T_g's) of these PEIs were recorded between 200–234 °C. Decomposition temperatures of 10% weight loss all occurred above 490 °C in both air and nitrogen atmospheres, and their residues were more than 43% at 800 °C in nitrogen atmosphere. The cyclohexane cardo‐based PEIs exhibited relatively higher T_g's, better solubilities in organic solvents, and better tensile properties as compared with the corresponding Ultem® PEI system. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 788–799, 2001     

New poly(oxyethylene) derivatives and their oligo analogues from Diels–Alder reactions of 5‐[methoxypoly(oxyethylene)]‐(3E)‐1, 3‐pentadiene and 5‐methoxyethoxy‐(3E)‐1,3‐pentadiene

Diels–Alder reactions of 5‐[methoxypoly(oxyethylene)]‐(3E)‐1,3‐pentadiene ( 1a ) with maleic anhydride, diethyl acetylenedicarboxylate (DADC), and acrolein were investigated for the synthesis of new poly(ethylene glycol) derivatives. To facilitate the characterization of the derivatives, Diels–Alder reactions of 5‐methoxyethoxy‐(3E)‐1,3‐pentadiene ( 1b ) with the aforementioned dienophiles were also studied. The reaction of o‐toluidine with the cycloaddition product from maleic anhydride and 1b resulted in the corresponding amide products. The reactions of 2,3‐dichloro‐5,6‐dicyano‐1,4‐benzoquinone with cycloadducts derived from 1a and 1b with DADC resulted in the aromatization of the corresponding products. An NMR analysis of the adducts obtained from 1a and acrolein in water and from 1b and acrolein in water/acetonitrile (4:1 v/v) indicated a mixture of endo and exo, with the endo concentration being approximately 80%. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1895–1902, 2005     

Polymerization of 1,3‐dienes with functional groups. II. Free‐radical polymerization of N‐(2‐methylene‐3‐butenoyl)piperidine

The free‐radical homopolymerization and copolymerization behavior of N‐(2‐methylene‐3‐butenoyl)piperidine was investigated. When the monomer was heated in bulk at 60 °C for 25 h without an initiator, about 30% of the monomer was consumed by the thermal polymerization and the Diels–Alder reaction. No such side reaction was observed when the polymerization was carried out in a benzene solution with 1 mol % 2,2′‐azobisisobutylonitrile (AIBN) as an initiator. The polymerization rate equation was found to be R_p ∝ [AIBN]^0.507[M]^1.04, and the overall activation energy of polymerization was calculated to be 89.5 kJ/mol. The microstructure of the resulting polymer was exclusively a 1,4‐structure that included both 1,4‐E and 1,4‐Z configurations. The copolymerizations of this monomer with styrene and/or chloroprene as comonomers were carried out in benzene solutions at 60 °C with AIBN as an initiator. In the copolymerization with styrene, the monomer reactivity ratios were r₁ = 6.10 and r₂ = 0.03, and the Q and e values were calculated to be 10.8 and 0.45, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1545–1552, 2003     

Investigation at the chain segmental level of the miscibility of poly(vinyl chloride)/atactic poly(methyl methacrylate) blends

We employed high‐resolution ¹³C cross‐polarization/magic‐angle‐spinning/dipolar‐decoupling NMR spectroscopy to investigate the miscibility and phase behavior of poly(vinyl chloride) (PVC)/poly(methyl methacrylate) (PMMA) blends. The spin–lattice relaxation times of protons in both the laboratory and rotating frames [T₁(H) and T_1ρ(H), respectively] were indirectly measured through ¹³C resonances. The T₁(H) results indicate that the blends are homogeneous, at least on a scale of 200–300 Å, confirming the miscibility of the system from a differential scanning calorimetry study in terms of the replacement of the glass‐transition‐temperature feature. The single decay and composition‐dependent T_1ρ(H) values for each blend further demonstrate that the spin diffusion among all protons in the blends averages out the whole relaxation process; therefore, the blends are homogeneous on a scale of 18–20 Å. The microcrystallinity of PVC disappears upon blending with PMMA, indicating intimate mixing of the two polymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2390–2396, 2001     

Miscibility and intermolecular specific interactions in thermosetting blends of bisphenol S epoxy resin with poly(ethylene oxide)

Thermosetting blends composed of phloroglucinol‐cured bisphenol S epoxy resin and poly(ethylene oxide) (PEO) were prepared via the in situ curing reaction of epoxy in the presence of PEO, which started from initially homogeneous mixtures of diglycidyl ether of bisphenol S, phloroglucinol, and PEO. The miscibility of the blends after and before the curing reaction was established on the basis of thermal analysis (differential scanning calorimetry). Single and composition‐dependent glass‐transition temperatures (T_g's) were observed for all the blend compositions after and before curing. The experimental T_g's could be explained well by the Gordon–Taylor equation. Fourier transform infrared spectroscopy indicated that there were competitive hydrogen‐bonding interactions in the binary thermosetting blends upon the addition of PEO to the system, which was involved with the intramolecular and intermolecular hydrogen‐bonding interactions, that is, OH···O?S, OH···OH, and OH, versus ether oxygen atoms of PEO between crosslinked epoxy and PEO. On the basis of infrared spectroscopy results, it was judged that from weak to strong the strength of the hydrogen‐bonding interactions was in the following order: OH···O?S, OH···OH, and OH versus ether oxygen atoms of PEO. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 359–367, 2005