Determination of Triazines by Ultrasonic-Assisted Ionic Liquid Microextraction Coupled with High Performance Liquid Chromatography

The determination of triazine herbicides by ultrasonic‐assisted ionic liquid microextraction coupled with high‐performance liquid chromatography was described. 1‐Hexyl‐3‐methylimidazolium hexafluorophosphate ([C₆MIm][PF₆]) was used as the extraction solvent and some extraction parameters, including volume of [C₆MIm][PF₆], extraction temperature and time, salt concentration and pH values of sample solution, were examined and optimized. The isolation of the target compounds from the matrix was found to be efficient when triazines in 10 mL of sample solution was extracted with 100 µL of [C₆MIm][PF₆] for 40 min at 50°C. The detection limits for the triazine range from 0.36 to 1.41 µg·L^?1. The satisfactory recoveries (82.3% –120.3%) with relative standard deviations ≦10.1% were obtained for the four triazine herbicides from six kinds of practical water samples.     

Ionic liquid for single‐drop microextraction followed by high‐performance liquid chromatography‐ultraviolet detection to determine carbonyl compounds in environmental waters

A sensitive method based on ionic liquid for single‐drop liquid microextraction coupled with HPLC‐UV was developed for the determination of carbonyl compounds in environmental waters using 1‐octyl‐3‐methylimidazolium hexafluorophosphate [C₈min][PF₆] as extraction solvent and 2,4‐dinitrophenylhydrazine as derivatizing agent. The extraction parameters affecting the enrichment factors such as solvent volume, pH, extraction time and salt concentration were investigated. A homemade funnel form polytetrafluoroethylene sleeve was fixed at the tip of the syringe needle and this allowed the use of 10 μL drop of ionic liquid for direct immersion extraction. Under the optimal conditions, the remarkable enrichment factors up to 150‐fold were obtained depending on the target analytes. The method has been validated when rectilinear relationship was obtained between the concentrations of analytes and peak area in the range of 5–100 ng/mL, the correlation coefficients were from 0.995 to 0.998, and the limit of detection was in the range of 0.04–2.03 ng/mL. The method was applied to monitor the concentration of carbonyl compounds in environmental waters with spiked recovery in the range of 84.2–106.9%.     

Temperature‐controlled ionic liquid‐dispersive liquid‐phase microextraction for preconcentration of chlorotoluron,diethofencarb and chlorbenzuron in water samples

This article describes a new, rapid and sensitive method for the determination of chlorotoluron, diethofencarb and chlorbenzuron from water samples with temperature‐controlled ionic liquid‐dispersive liquid‐phase microextraction. In the preconcentration procedure, ionic liquid 1‐hexyl‐3‐methylimidazolium hexafluorophosphate [C₆MIM] [PF₆] was employed as the extraction solvent. The parameters, such as volume of [C₆MIM] [PF₆], sample pH, extraction time, centrifuging time, temperature and salting‐out effect, were investigated in detail. Under the optimal extraction conditions, it has been found that three analytes had excellent LODs (S/N=3) in the range of 0.04–0.43 μg/L. The RSDs (n=6) were in the range of 1.3–4.7%. The proposed method was evaluated with lake water, tap water and melted snow water samples. The experimental results indicated that the proposed method had excellent prospect and would be widely used in the future.     

Temperature‐controlled ionic liquid dispersive liquid‐phase microextraction combined with HPLC with ultraviolet detector for the determination of fungicides

Present study described a simple, environmental benign, easy to operate, and determination method for fungicides including thiram, metalaxyl, diethofencarb, myclobutanil, and tebuconazole. The method is based on temperature‐controlled ionic liquid dispersive liquid phase microextraction coupled to HPLC with ultraviolet detector. In the enrichment procedure, ionic liquid 1‐octyl‐3‐methylimidazolium hexafluorophosphate [C₈MIM][PF₆] was used as the extraction solvent. Variable affecting parameters such as the volume of [C₈MIM][PF₆], temperature, extraction time, centrifuging time, and salting‐out effect have been optimized in detail. Under the optimal conditions, this method has been found to have good linear relationship in the concentration range of 1.0–100 μg/L and excellent detection sensitivity with LODs (S/N = 3) in the range of 0.32–0.79 μg/L. Precisions of proposed method were in the range of 3.7–5.9% for intraday and 7.8–11.0% for interday (RSDs, n = 6). The proposed method was used for the analysis of real water samples and good spiked recoveries at two different spiked levels were achieved in the range of 84.6–102%.     

Studies on Liquid/liquid Extraction of Copper Ion with Room Temperature Ionic Liquid

Room temperature ionic liquids are regarded as “Green solvents” for their nonvolatile and thermally stable properties. They are employed to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. In this work, a water immiscible room temperature ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent for liquid/liquid extraction of copper ions. Metal chelators, including dithizone, 8‐hydroxyquinoline, and 1‐(2‐pyridylazo)‐2‐naphthol, were employed to form neutral metal‐chelate complexes with copper ions so that copper ions were extracted from aqueous solution into [C₄mim][PF₆]. The parameters that affect the extraction of copper ions with this biphasic system were investigated. The extraction behavior in this novel biphasic system is shown to be consistent with that of traditional solvents. For example, the extraction with this biphasic system is strongly pH dependent. So, the extraction efficiency of coppers ion from an aqueous phase can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation and preconcentraction of copper ions can be accomplished by controlling the pH value of the extraction system. It appears that the use of ionic liquid as an alternate solvent system in liquid/liquid extraction of copper ions is very promising.     

Ultrasound assisted ionic liquid dispersive liquid phase extraction of lovastatin and simvastatin: A new pretreatment procedure

A fast and novel sample preparation procedure: ultrasound assisted ionic liquid (IL) dispersive liquid extraction for the concentration of lovastatin and simvastatin in aqueous samples was developed. An IL ([C₆MIM][PF₆]) was used as the extraction solvent, and the factors affecting the extraction efficiency such as initial temperature, the volume of IL, pH of water samples, cooling time, and salt concentration were optimized. In combination with HPLC‐UV, both lovastatin and simvastatin exhibited a good linear range of 1–100 ng/mL. The limits of detection (LODs) of lovastatin and simvastatin were 0.17 and 0.29 ng/mL, respectively. Precisions of the proposed method (RSDs, n = 9) were 4.12 and 4.52%, respectively. This method has been successfully applied for the analysis of target compounds in three real water samples and good spiking recoveries were obtained in the range of 90.0–102.2% for lovastatin and 80.5–112.0% for simvastatin. These results indicated that ultrasound assisted IL dispersive liquid phase extraction would have good application prospect in the pretreatment of environmental samples.     

Determination of triazines in honey by dispersive liquid–liquid microextraction high-performance liquid chromatography

Dispersive liquid–liquid microextraction (DLLME) high-performance liquid chromatography (HPLC) was developed for extraction and determination of triazines from honey. A room temperature ionic liquid, 1-hexyl-3-methylimidazolium hexafluorophosphate [C₆MIM][PF_6.], was used as extraction solvent and Triton X 114 was used as dispersant. A mixture of 175 μL [C₆MIM][PF₆] and 50 μL 10% Triton X 114 was rapidly injected into the 20 mL honey sample by syringe. After extraction, phase separation was performed by centrifugation and the sedimented phase was analyzed by HPLC. Some experimental parameters, such as type and volume of extraction solvent, concentration of dispersant, pH value of sample solution, salt concentration and extraction time were investigated and optimized. The detection limits for chlortoluron, prometon, propazine, linuron and prebane are 6.92, 5.84, 8.55, 8.59 and 5.31 μg kg⁻¹, respectively. The main advantages of the proposed method are simplicity of operation, low cost, high enrichment factor and extraction solvent volume at microliter level. Honey samples were analyzed by the proposed method and obtained results indicated that the proposed method provides acceptable recoveries and precisions.     

Room temperature ionic liquid as a novel medium for liquid/liquid extraction of metal ions

Room temperature ionic liquids (RTILs) have been used as novel solvents to replace traditional volatile organic solvents in organic synthesis, solvent extraction, and electrochemistry. The hydrophobic character and water immiscibility of certain ionic liquids allow their use in solvent extraction of hydrophobic compounds. In this work, a typical room temperature ionic liquid, 1-butyl-3-methylimidazolium hexafluorophosphate [C₄mim][PF₆], was used as an alternative solvent to study liquid/liquid extraction of heavy metal ions. Dithizone was employed as a metal chelator to form neutral metal-dithizone complexes with heavy metal ions to extract metal ions from aqueous solution into [C₄mim][PF₆]. This extraction is possible due to the high distribution ratios of the metal complexes between [C₄mim][PF₆] and aqueous phase. Since the distribution ratios of metal dithiozonates between [C₄mim][PF₆] and aqueous phase are strongly pH dependent, the extraction efficiencies of metal complexes can be manipulated by tailoring the pH value of the extraction system. Hence, the extraction, separation, and preconcentraction of heavy metal ions with the biphasic system of [C₄mim][PF₆] and aqueous phase can be achieved by controlling the pH value of the extraction system. Preliminary results indicate that the use of [C₄mim][PF₆] as an alternate solvent to replace traditional organic solvents in liquid/liquid extraction of heavy metal ions is very promising.     

Comparison of two ultrasound‐enhanced microextractions combined with HPLC for determining acaricides in water

An ultrasound‐enhanced in situ solvent formation microextraction has been developed first time and compared with ultrasound‐enhanced ionic‐liquid‐assisted dispersive liquid–liquid microextraction for the HPLC analysis of acaricides in environmental water samples. A ionic liquid ([C₈MIM][PF₆]) was used as the green extraction solvent through two pathways. The experimental parameters, such as the type and volume of both of the extraction solvent disperser solvent, ultrasonication time, and salt addition, were investigated and optimized. The analytical performance using the optimized conditions proved the feasibility of the developed methods for the quantitation of trace levels of acaricides by obtaining limits of detection that range from 0.54 to 3.68 μg/L. The in situ solvent formation microextraction method possesses more positive characteristics than the ionic‐liquid‐assisted dispersive liquid–liquid microextraction method (except for spirodiclofen determination) when comparing the validation parameters. Both methods were successfully applied to determining acaricides in real water samples.     

Homogeneous ionic liquid microextraction of the active constituents from fruits of Schisandra chinensis and Schisandra sphenanthera

Homogeneous ionic liquid microextraction (HILME) was developed for the extraction of schizandrin, schisantherin A and deoxyschizandrin from Schisandra chinensis and Schisandra sphenanthera. 1-Butyl-3-methylimidazolium tetrafluoroborate ([C₄MIM][BF₄]) aqueous solution was used as extraction solvent, and ammonium hexafluorophosphate ([NH₄][PF₆]) was used as ion-pairing agent. 1-Butyl-3-methylimidazolium hexafluorophosphate ([C₄MIM][PF₆]), which is barely soluble in water, was formed in situ, and was used as sample solution. High-performance liquid chromatography (HPLC) was employed for separation and determination of the analytes. The calibration curve showed good linear relationship (r > 0.9998). The recoveries were between 69.71% and 88.33% with RSDs lower than 4.86%. External standard method was adopted in the proposed method, and internal standard method was applied for the evaluation of the proposed method. The two methods were compared and the results indicated that the proposed method was acceptable and simple. The HILME is free of volatile organic solvents, and represents lower expenditures of sample, extraction time and solvent, compared with ultrasonic and Soxhlet extraction. There was no obvious difference in the extraction yields of active constitutions obtained by the three extraction methods.     

Determination of estrogens in environmental water samples using 1,3‐dipentylimidazolium hexafluorophosphate ionic liquid as extraction solvent in dispersive liquid–liquid microextraction

In this work, the potential of a symmetric dialkyl‐substituted ionic liquid (IL), 1,3‐dipenthylimidazolium hexafluorophosphate ([PPIm][PF₆]), as extraction solvent in dispersive liquid–liquid microextraction (DLLME) has been studied for the analysis of a group of three natural (estriol, 17β‐estradiol, and 17α‐estradiol) and four synthetic (17α‐ethynylestradiol, diethylstibestrol, dienestrol, and hexestrol) estrogenic compounds as well as one mycotoxin with estrogenic activity (zearalenone) in different types of water samples (Milli‐Q, mineral, and wastewater). Separation, determination, and quantification were developed by HPLC‐DAD and a fluorescence detector (FD) connected in series. Factors influencing the IL‐DLLME procedure (sample pH, amount of IL, type and volume of disperser solvent, ionic strength, and assistance of vortex agitation) were investigated and optimized by means of a step‐by‐step approach. Once the optimum extraction conditions were established (10 mL of water at pH 8, 60 mg of [PPIm][PF₆], 500 μL of ACN as disperser solvent and vortex agitation for 1 min), the calibration curves of the whole method (IL‐DLLME‐HPLC‐DAD/FD) were obtained and precision and accuracy were evaluated. It was demonstrated that the developed methodology was repeatable, accurate, and selective with limits of detection in the 0.30–0.57 μg/L and 13.8–37.1 μg/L range for FD and DAD, respectively. Relative recovery values were higher than 85% for the different types of water samples and the Student's t test demonstrated that there were not significant differences between the added and the found concentration.     

Determination of four trace preservatives in street food by ionic liquid-based dispersive liquid-liquid micro-extraction

A rapid and simple ionic liquid-based dispersive liquid-liquid micro-extraction (DLLME) method has been developed to pre-concentrate four paraben preservatives (methylparaben, ethylparaben, propylparaben, and butylparaben) from street food (pancakes). Several potentially influential factors such as the type of ionic liquid and disperser solvent, extraction time, sample pH, ionic strength, and the volume of the ionic liquid and disperser solvent were investigated. The optimum experimental conditions for the proposed micro-extraction process were: 0.1 mL of 1-octyl-3-methylimidazolium hexafluorophosphate ([C₈MIM][PF₆]) as an extraction solvent, 0.1 mL of acetonitrile as a disperser solvent, 5 min extraction time, and sample ionic strength of 30 % sodium chloride in water sample at pH 6.0. The LODs and LOQs were in the range of 1.0–1.5 ng g⁻¹ and 3.5–4.5 ng g⁻¹, respectively. Spiking recoveries were in the range of 60.1–79.5 % and the associated RSDs were all in the range of 1.8–7.0 %. The results show that DLLME is a suitable method for the determination of parabens in pancake samples and ionic liquid is a good extractant in this process.     

Synthesis of 2‐Phenylthiazoles from α‐Tosyloxyketones and Thiobenzamide in [Bmim][PF6] Ionic Liquid at Ambient Temperature

The room temperature ionic liquid, 1‐n‐butyl‐3‐methylimidazolium hexafluorophosphate [bmim][PF₆] is used as a ‘green’ recyclable alternative to classical molecular solvents for the cyclocondensation of α‐tosyloxyketones with thiobenzamide to prepare 2‐phenylthiazoles in good yields.     

Ultrasound‐assisted temperature‐controlled ionic liquid emulsification microextraction coupled with capillary electrophoresis for the determination of parabens in personal care products

We developed a CE and ultrasound‐assisted temperature‐controlled ionic liquid emulsification microextraction method for the determination of four parabens (methyl paraben, ethyl paraben, propyl paraben, and butyl paraben) in personal care products including mouthwash and toning lotion. In the proposed extraction procedure, ionic liquid (IL, 1‐octyl‐3‐methylimidazolium hexafluorophosphate) was used as extraction solvent, moreover, no disperser solvent was needed. Parameters affecting the extraction efficiency including volume of IL, heating temperature, ultrasonic time, extraction time, sample pH, ionic strength, and centrifugation time were optimized. Under the optimized conditions, the method was found to be linear over the range of 3–500 ng/mL with coefficient of determination (R²) in the range of 0.9990–0.9998. The LODs and LOQs for the four parabens were 0.45–0.72 ng/mL and 1.50–2.40 ng/mL, respectively. Intraday and interday precisions (RSDs, n = 5) were in the range of 5.4–6.8% and 7.0–8.7%, respectively. The recoveries of parabens at different spiked levels ranged from 71.9 to 119.2% with RSDs less than 9.5%.     

Solvent (ionic liquid) impregnated resin-based extraction coupled with dynamic ultrasonic desorption for separation and concentration of four herbicides in environmental water

A new method was developed for the determination of monolinuron, propazine, linuron, and prebane in environmental water samples. The solvent (ionic liquid) impregnated resin (IL-SIR)-based extraction coupled with dynamic ultrasonic desorption (DUSD) was applied to the separation and concentration of the analytes. The high performance liquid chromatography (HPLC) was applied to the determination of the analytes. The ionic liquid [C₆MIM][PF₆] was immobilized on Diaion HP20 resin by immersing the resin in ethanol solution containing [C₆MIM][PF₆]. The effect of extraction parameters, including pH value of sample solution, salt concentration in sample and extraction time, and elution conditions, including the concentration of ethanol in elution solvent, the flow rate of elution solvent and the ultrasonic power, were examined and optimized. The limits of detection and quantification for the analytes were in the range of 0.15-0.29 μg L⁻¹ and 0.51-0.98 μg L⁻¹, respectively. Some environmental water samples were analyzed and the analytical results were satisfactory.     

离子液体-水介质中离子液体负载TEMPO催化选择氧化合成脂肪醇羟基芳香醛和酮

由于脂肪醇羟基和苄醇羟基具有相同的氧化反应活性,所以当分子内同时含有脂肪醇羟基和苄醇羟基时,很难选择氧化苄醇羟基合成含脂肪醇羟基的芳香醛或酮。本文报道了在离子液体-水介质中,NCS/NaBr/IL-TEMPO（离子液体负载TEMPO）催化氧化合成含有脂肪醇羟基的芳香醛、酮的方法,反应条件温和,选择性好,收率高,且离子液体和催化剂可以循环使用。     

Up‐and‐down shaker‐assisted ionic liquid‐based dispersive liquid—liquid microextraction of benzophenone‐type ultraviolet filters

Sun protection is an important part of our lives. UV filters are widely used to absorb solar radiation in sunscreens. However, excess UV filters constitute persistent groups of organic micropollutants present in the environment. An environmentally friendly ionic‐liquid‐based up‐and‐down shaker‐assisted dispersive liquid?liquid microextraction device combined with ultra‐performance liquid chromatography coupled with photodiode‐array detection has been developed to preconcentrate three UV filters (benzophenone, 2‐hydroxy‐4‐methoxybenzophenone, 2,2′‐dihydroxy‐4‐methoxybenzophenone) from field water samples. In this method, the optimal conditions for the proposed extraction method were: 40 μL [C₈MIM][PF₆] as extraction solvent and 200 μL methanol as disperser solvent were used to extract the UV filters. After up‐and‐down shaking for 3 min, the aqueous solution was centrifuged at 5000 rpm speed, then using microtube to collect the settled extraction solvent and using ultra‐performance liquid chromatography for further analysis. Quantification results indicated that the linear range was 2–1000 ng/mL. The LOD of this method was in the range 0.2–1.3 ng/mL with r² ≥ 0.9993. The relative recovery in studies of different types of field water samples was in the range 92–120%, and the RSD was 2.3–7.1%. The proposed method was also applied to the analysis of field samples.     

Ionic liquid as a complexation and extraction medium combined with high-performance liquid chromatography in the evaluation of chromium(VI) and chromium(III) speciation in wastewater samples

A simple method has been proposed for the determination of chromium species by high-performance liquid chromatography (HPLC) after preconcentration by the ionic liquid, 1-butyl-3-methyimidazolium hexafluorophosphate ([C₄MIM][PF₆]). The simultaneous preconcentration of Cr(VI) and Cr(III) in wastewater was achieved with ammonium pyrrolidinedithiocarbamate (APDC) as the chelating agent and the ionic liquid [C₄MIM][PF₆] as the extractant. Baseline separation of the APDC chelates of Cr(III) and Cr(VI) was realised on a RP-C18 column using a mixture of methanol–acetonitrile–water (53:14:33, v/v) as the mobile phase at a flow rate of 1.0 mL min^{− 1}. The influences of several variables on the complexation and extraction were evaluated: pH, reaction time, APDC concentration and metal ion interference. Our results showed that when the linear concentration of Cr(VI) and Cr(III) ranged from 25 to 200 μg L^{− 1}, their linear correlation coefficients were between 0.9977 and 0.9978, their recoveries ranged from 91.8% to 95.8% and their relative standard deviations (n = 3) were between 0.31% and 1.8%. Common metal ions in water did not interfere with the determination. This method is a simple, fast, accurate, highly stable and selective method and has successfully been applied to the speciation of chromium in wastewater.     

Determination of Polycyclic Aromatic Hydrocarbons in Tobacco Smoke by Ionic Liquid Enrichment and Gas Chromatography – Mass Spectrometry

A rapid, efficient and environmentally friendly method based on the ionic liquid (IL) 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) was developed for the determination of 16 polycyclic aromatic hydrocarbons (PAHs) in mainstream tobacco smoke. This technique combined ionic liquid (IL) enrichment with solvent reverse extraction for the replacement of solid phase extraction and rotary evaporation in the traditional method and enriched PAHs in the organic solvent. Several parameters, including the type of ionic liquid, volume of ionic liquid and water, extraction time, vortex time and reverse extraction time, were optimized. After pretreatment, the analytes were analyzed by gas chromatography-mass spectrometry (GC-MS) using selective ion monitoring (SIM). Satisfactory results were achieved when this method was applied to determine PAHs in mainstream tobacco smoke. The calibration curves were linear with correlation coefficients ranging from 0.9955 to 0.9999 at concentration levels of 10–800?µg?L^?1, and the relative standard deviations of the optimized method were between 0.7% and 5.3%. The limits of detection were 0.01–0.6?ng cig^?1, and the recoveries of the compounds were 80.2–118%. A comparison of this protocol with literature methods demonstrated that the proposed procedure provides accurate and reliable sample-treatment for the determination of PAHs in tobacco samples.     

A Novel Room Temperature Ionic Liquid Extraction Spectrophotometric Determination of Trace Germanium in Natural Water with Methybenzeneazosalicylfluorone

Abstract

This paper describes a highly sensitive and selective extraction spectrophotometric method for determination of trace germanium in natural water with new a chromogenic reagent methybenzeneazosalicylfluorone abbreviated as MBASF, in which a typical room temperature ionic liquid, 1‐butyl‐3‐methylimidazolium hexafluorophosphate abbreviated as [C₄mim][PF₆] was used as novel medium for liquid/liquid extraction of germanium(IV). In the presence of TritonX‐100, MBASF reacted with germanium(IV) to form a red complex rapidly, the complex was then extracted into the [C₄mim][PF₆] phase, the absorbance of the complex in ionic liquid at 496 nm was recorded and used to determine trace germanium(IV). The apparent molar absorptivity of the complex and the detection limit for the real sample were found to be 3.12×10⁶ L mol^?1 cm^?1 and 0.2 ng mL^?1, respectively. The absorbance of the complex at 496 nm increases linearly with the concentration up to 4 µg of germanium (IV) in 250 mL of aqueous solution. The interference study show the determination of germanium is free from the interference of almost all positive and negative ions found in the natural water samples. The determination of germanium in natural water was carried out by the present method and electrothermal atomic absorption spectrometry (AAS). The results were satisfactorily comparable so that the applicability of the proposed method was confirmed using the real samples. Moreover, the extraction mechanism with the ionic liquid system was also investigated. We think the extraction performance of the ionic liquid system is a combination of ion‐pairing effect between imidazolium cation and basic solute in the aqueous phase with the dissolution of polar molecule in ionic liquid phase. A wise choice of the appropriate combination of anion with imidazolium cation hydrophobicity allows playing with solute selectivity.