Coupled Solar Battery with 6.9 % Efficiency

Solar-to-electrochemical energy storage in solar batteries is an important solar utilization technology comparable to solar-to-electricity (solar cells) and solar-to-fuel (photocatalytic cells) conversion. Unlike the indirect approach of integrated solar flow batteries combining photoelectrodes with redox-electrodes, coupled solar batteries enable direct solar energy storage, but are hampered by low efficiency due to rapid charge recombination of materials and misaligned energy levels between electrodes. Herein, we propose a design for a coupled solar battery that intercouples two photo-coupled ion transfer (PCIT) reactions through electron-ion transfer upon co-photo-pumping of photoelectrochemical storage cathode and anode. We used a representative covalent organic framework (COF) to achieve efficient charge separation and directional charge transfer between two band-matched photoelectrochemical storage electrodes, with a photovoltage sufficient for COF dual-redox reactions. By pumping these electrodes, the coupled solar battery stores solar energy via two synergistic PCIT reactions of electron-proton-relayed COF oxidation and reduction, and the stored solar energy is released as electrochemical energy during COF regeneration in discharge while interlocking the loops. A breakthrough in efficiency (6.9 %) was achieved, adaptive to a large-area (56 cm²) tandem device. The presented photo-intercoupled electron-ion transfer (PIEIT) mechanism provides expandable paths toward practical solar-to-electrochemical energy storage.     

Photo‐excited Oxygen Reduction and Oxygen Evolution Reactions Enable a High‐Performance Zn–Air Battery

The storage of solar energy in battery systems is pivotal for a sustainable society, which faces many challenges. Herein, a Zn–air battery is constructed with two cathodes of poly(1,4‐di(2‐thienyl))benzene (PDTB) and TiO₂ grown on carbon papers to sandwich a Zn anode. The PDTB cathode is illuminated in a discharging process, in which photoelectrons are excited into the conduction band of PDTB to promote oxygen reduction reaction (ORR) and raise the output voltage. In a reverse process, holes in the valence band of the illuminated TiO₂ cathode are driven for the oxygen evolution reaction (OER) by an applied voltage. A record‐high discharge voltage of 1.90 V and an unprecedented low charge voltage of 0.59 V are achieved in the photo‐involved Zn–air battery, regardless of the equilibrium voltage. This work offers an innovative pathway for photo‐energy utilization in rechargeable batteries.     

Modulating Benzothiadiazole‐Based Covalent Organic Frameworks via Halogenation for Enhanced Photocatalytic Water Splitting

Two‐dimensional covalent organic frameworks (2D COFs), an emerging class of crystalline porous polymers, have been recognized as a new platform for efficient solar‐to‐hydrogen energy conversion owing to their pre‐designable structures and tailor‐made functions. Herein, we demonstrate that slight modulation of the chemical structure of a typical photoactive 2D COF (Py‐HTP‐BT‐COF) via chlorination (Py‐ClTP‐BT‐COF) and fluorination (Py‐FTP‐BT‐COF) can lead to dramatically enhanced photocatalytic H₂ evolution rates (HER=177.50 μmol h^?1 with a high apparent quantum efficiency (AQE) of 8.45 % for Py‐ClTP‐BT‐COF). Halogen modulation at the photoactive benzothiadiazole moiety can efficiently suppress charge recombination and significantly reduce the energy barrier associated with the formation of H intermediate species (H*) on polymer surface. Our findings provide new prospects toward design and synthesis of highly active organic photocatalysts toward solar‐to‐chemical energy conversion.     

Bipolar poly(p‐phenylene vinylene)s bearing electron‐donating triphenylamine or carbazole and electron‐accepting quinoxaline moieties

Two new poly(phenylene vinylene)s (PPVs) carrying electron‐donating triphenylamine or carbazole and electron‐deficient quinoxaline units were synthesized and characterized. Their properties were compared with those of PPV containing only quinoxaline unit. The two polymers showed PL maximum at 501–510 in solution and 533–540 in thin film. Because of the presence of electron donor and acceptor units they displayed strong intramolecular charge transfer (ICT) effects; hence, low‐photoluminescence quantum yields. The polymers showed reversible electrochemical reduction with electron affinity of 2.75 eV and irreversible oxidation with ionization potential of 5.10–5.24 eV. Single‐layer LED of configuration ITO/PEDOT/polymer/Al showed low turn‐on voltage at 5 V, but limited brightness of 50–60 cdm^?2. The electroluminescence maximum was voltage‐tunable varying from 500 to 542 nm. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2367–2378, 2008     

Rechargeable Room‐Temperature Na–CO2 Batteries

Developing rechargeable Na–CO₂ batteries is significant for energy conversion and utilization of CO₂. However, the reported batteries in pure CO₂ atmosphere are non‐rechargeable with limited discharge capacity of 200 mAh g^?1. Herein, we realized the rechargeability of a Na–CO₂ battery, with the proposed and demonstrated reversible reaction of 3 CO₂+4 Na?2 Na₂CO₃+C. The battery consists of a Na anode, an ether‐based electrolyte, and a designed cathode with electrolyte‐treated multi‐wall carbon nanotubes, and shows reversible capacity of 60000 mAh g^?1 at 1 A g^?1 (≈1000 Wh kg^?1) and runs for 200 cycles with controlled capacity of 2000 mAh g^?1 at charge voltage <3.7 V. The porous structure, high electro‐conductivity, and good wettability of electrolyte to cathode lead to reduced electrochemical polarization of the battery and further result in high performance. Our work provides an alternative approach towards clean recycling and utilization of CO₂.     

Functionalized Alkynylplatinum(II) Polypyridyl Complexes for Use as Sensitizers in Dye‐Sensitized Solar Cells

A series of platinum(II) alkynyl‐based sensitizers has been synthesized and found to show light‐to‐electricity conversion properties. These dyes were developed as sensitizers for the application in nanocrystalline TiO₂ dye‐sensitized solar cells (DSSCs). Their photophysical and electrochemical properties were studied. The excited‐state property was probed using nanosecond transient absorption spectroscopy, which showed the formation of a charge‐separated state that arises from the intramolecular photoinduced charge transfer from the platinum(II) alkynylbithienylbenzothiadiazole moiety (donor) to the polypyridyl ligand (acceptor). A lifetime of 3.4 μs was observed for the charge‐separated state. A dye‐sensitized solar cell based on one of the complexes showed a short‐circuit photocurrent of 7.12 mA cm^?2, an open circuit voltage of 780 mV, and a fill factor of 0.65, thus giving an overall power conversion efficiency of 3.6 %.     

Energy‐Saving Electrolytic Hydrogen Generation: Ni2P Nanoarray as a High‐Performance Non‐Noble‐Metal Electrocatalyst

It is highly attractive but challenging to develop earth‐abundant electrocatalysts for energy‐saving electrolytic hydrogen generation. Herein, we report that Ni₂P nanoarrays grown in situ on nickel foam (Ni₂P/NF) behave as a durable high‐performance non‐noble‐metal electrocatalyst for hydrazine oxidation reaction (HzOR) in alkaline media. The replacement of the sluggish anodic oxygen evolution reaction with such the more thermodynamically favorable HzOR enables energy‐saving electrochemical hydrogen production with the use of Ni₂P/NF as a bifunctional catalyst for anodic HzOR and cathodic hydrogen evolution reaction. When operated at room temperature, this two‐electrode electrolytic system drives 500 mA cm⁻² at a cell voltage as low as 1.0 V with strong long‐term electrochemical durability and 100 % Faradaic efficiency for hydrogen evolution in 1.0 m KOH aqueous solution with 0.5 m hydrazine.     

New D‐A‐A’‐Configured Small Molecule Donors Employing Conjugation to Red‐shift the Absorption for Photovoltaics

Four new donor‐acceptor‐acceptor’ (D‐A‐A’)‐configured donors, CPNT , DCPNT , CPNBT , and DCPNBT equipped with naphtho[1,2‐c:5,6‐c′]bis([1,2,5]‐thiadiazole) (NT) or naphtho[2,3‐c][1,2,5]thiadiazole (NBT) as the central acceptor (A) unit bridging triarylamine donor (D) and cyano or dicyanovinylene acceptor (A’), were synthesized and characterized. All molecules exhibit bathochromic absorption shifts as compared to those of the benzothiadiazole (BT)‐based analogues owing to improved electron‐withdrawing and quinoidal character of NT and NBT cores that lead to stronger intramolecular charge transfer. Favorable energy level alignments with C₇₀, together with the good thermal stability and the antiparallel dimeric packing render CPNT and DCPNT suitable donors for vacuum‐processed organic photovoltaics (OPV)s. OPVs based on DCPNT : C₇₀ active layers displayed the best power conversion efficiency (PCE)=8.3%, along with an open circuit voltage of 0.92 V, a short circuit current of 14.5 mA cm^?2 and a fill factor of 62% under 1 sun intensity, simulated AM1.5G illumination. Importantly, continuous light‐soaking with AM 1.5G illumination has verified the durability of the devices based on CPNT :C₇₀ and DCPNT : C₇₀ as the active blends. The devices were examined for their feasibility of indoor light harvesting under 500 lux illumination by a TLD‐840 fluorescent lamp, giving PCE=12.8% and 12.6%, respectively. These results indicate that the NT‐based D‐A‐A’‐type donors CPNT and DCPNT are potential candidates for high‐stability vacuum‐processed OPVs suitable for indoor energy harvesting.     

Photoinduced Oxygen Reduction Reaction Boosts the Output Voltage of a Zinc–Air Battery

Utilization of solar energy is of great interest for a sustainable society, and its conversion into electricity in a compact battery is challenging. Herein, a zinc–air battery with the polymer semiconductor polytrithiophene (pTTh) as the cathode is reported for direct conversion of photoenergy into electric energy. Upon irradiation, photoelectrons are generated in the conduction band (CB) of pTTh and then injected into the π_2p* orbitals of O₂ for its reduction to HO₂^?, which is disproportionated to OH^? and drives the oxidation of Zn to ZnO at the anode. The discharge voltage was significantly increased to 1.78 V without decay during discharge–charge cycles over 64 h, which corresponds to an energy density increase of 29.0 % as compared to 1.38 V for a zinc–air battery with state‐of‐the‐art Pt/C. The zinc–air battery with an intrinsically different reaction scheme for simultaneous conversion of chemical and photoenergy into electric energy opens a new pathway for utilization of solar energy.     

High‐Performance K–CO2 Batteries Based on Metal‐Free Carbon Electrocatalysts

Metal–CO₂ batteries have attracted much attention owing to their high energy density and use of greenhouse CO₂ waste as the energy source. However, the increasing cost of lithium and the low discharge potential of Na–CO₂ batteries create obstacles for practical applications of Li/Na–CO₂ batteries. Recently, earth‐abundant potassium ions have attracted considerable interest as fast ionic charge carriers for electrochemical energy storage. Herein, we report the first K–CO₂ battery with a carbon‐based metal‐free electrocatalyst. The battery shows a higher theoretical discharge potential (E^?=2.48 V) than that of Na–CO₂ batteries (E^?=2.35 V) and can operate for more than 250 cycles (1500 h) with a cutoff capacity of 300 mA h g^?1. Combined DFT calculations and experimental observations revealed a reaction mechanism involving the reversible formation and decomposition of P12₁/c1‐type K₂CO₃ at the efficient carbon‐based catalyst.     

Poly(2,5‐dimercapto‐1,3,4‐thiadiazole) as a Cathode for Rechargeable Lithium Batteries with Dramatically Improved Performance

Organosulfur compounds with multiple thiol groups are promising for high gravimetric energy density electrochemical energy storage. We have synthesized a poly(2,5‐dimercapto‐1,3,4‐thiadiazole) (PDMcT)/poly(3,4‐ethylenedioxythiophene) (PEDOT) composite cathode for lithium‐ion batteries with a new method and investigated its electrochemical behavior by charge/discharge cycles and cyclic voltammetry (CV) in an ether‐based electrolyte. Based on a comparison of the electrochemical performance with a carbonate‐based electrolyte, we found a much higher discharge capacity, but also a very attractive cycling performance of PDMcT by using a tetra(ethylene glycol) dimethyl ether (TEGDME)‐based electrolyte. The first discharge capacity of the as‐synthesized PDMcT/PEDOT composite approached 210 mAh g^?1 in the TEGDME‐based electrolyte. CV results clearly show that the redox reactions of PDMcT are highly reversible in this TEGDME‐based electrolyte. The reversible capacity remained around 120 mAh g^?1 after 20 charge/discharge cycles. With improved cycling performance and very low cost, PDMcT could become a very promising cathode material when combined with a TEGDME‐based electrolyte. The poor capacity in the carbonate‐based electrolyte is a consequence of the irreversible reaction of the DMcT monomer and dimer with the solvent, emphasizing the importance of electrolyte chemistry when studying molecular‐based battery materials.     

A Membrane‐Free Redox Flow Battery with Two Immiscible Redox Electrolytes

Flexible and scalable energy storage solutions are necessary for mitigating fluctuations of renewable energy sources. The main advantage of redox flow batteries is their ability to decouple power and energy. However, they present some limitations including poor performance, short‐lifetimes, and expensive ion‐selective membranes as well as high price, toxicity, and scarcity of vanadium compounds. We report a membrane‐free battery that relies on the immiscibility of redox electrolytes and where vanadium is replaced by organic molecules. We show that the biphasic system formed by one acidic solution and one ionic liquid, both containing quinoyl species, behaves as a reversible battery without any membrane. This proof‐of‐concept of a membrane‐free battery has an open circuit voltage of 1.4 V with a high theoretical energy density of 22.5 Wh L⁻¹, and is able to deliver 90 % of its theoretical capacity while showing excellent long‐term performance (coulombic efficiency of 100 % and energy efficiency of 70 %).     

Application of the Organic Photosensitizers Bearing Two Carboxylic Acid Groups to Dye‐Sensitized Solar Cells

Three electron donor‐?? bridge‐electron acceptor (D‐π‐A) organic dyes bearing two carboxylic acid groups were applied to dye‐sensitized solar cells (DSSC) as sensitizers, in which one triphenylamine or modified triphenylamine and two rhodanine‐3‐acetic acid fragments act as D and A, respectively. It was found that the introduction of t‐butyl or methoxy group in the triphenylamine subunit could lead to more efficient photoinduced intramolecular charge transfer, thus improving the overall photoelectric conversion efficiency of the resultant DSSC. Under global AM 1.5 solar irradiation (73 mW·cm^?2), the dye molecule based on methoxy‐substituted triphenylamine achieved the best photovoltaic performance: a short circuit photocurrent density (J_sc) of 12.63 mA·cm^?2, an open circuit voltage (V_oc) of 0.55 V, a fill factor (FF) of 0.62, corresponding to an overall efficiency (η) of 5.9%.     

Novel narrow‐band‐gap conjugated copolymers containing phenothiazine‐arylcyanovinyl units for organic photovoltaic cell applications

A series of novel narrow‐band‐gap copolymers ( P1 ‐ P12 ) composed of alkyl‐substituted fluorene (FO) units and six analogous mono‐ and bis(2‐aryl‐2‐cyanovinyl)‐10‐hexylphenothiazine monomers ( M1 ‐ M6 ) were synthesized by a palladium‐catalyzed Suzuki coupling reaction with two different feed in ratios of FO to M1 ‐ M6 (molar ratio = 3:1 and 1:1). The absorption spectra of polymers P1 ‐ P12 exhibited broad peaks located in the UV and visible regions from 400 to 800 nm with optical band gaps at 1.55–2.10 eV, which fit near the wavelength of the maximum solar photon reflux. Electrochemical experiments displayed that the reversible p‐ and n‐doping processes of copolymers were partially reversible, and the proper HOMO/LUMO levels enabled a high photovoltaic open‐circuit voltage. As blended with [6,6]‐phenyl C₆₁ butyric acid methyl ester (PCBM) as an electron acceptor in bulk heterojunction photovoltaic devices, narrow‐band‐gap polymers P1 ‐ P12 as electron donors showed significant photovoltaic performance which varied with the intramolecular donor‐acceptor interaction and their mixing ratios to PCBM. Under 100 mW/cm² of AM 1.5 white‐light illumination, the device of copolymer P12 produced the highest preliminary result having an open‐circuit voltage of 0.64 V, a short‐circuit current of 2.70 mA/cm², a fill factor of 0.29, and an energy conversion efficiency of 0.51%. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 4285–4304, 2008     

Design,Synthesis, and Photovoltaic Characterization of a Small Molecular Acceptor with an Ultra‐Narrow Band Gap

The design of narrow band gap (NBG) donors or acceptors and their application in organic solar cells (OSCs) are of great importance in the conversion of solar photons to electrons. Limited by the inevitable energy loss from the optical band gap of the photovoltaic material to the open‐circuit voltage of the OSC device, the improvement of the power conversion efficiency (PCE) of NBG‐based OSCs faces great challenges. A novel acceptor–donor–acceptor structured non‐fullerene acceptor is reported with an ultra‐narrow band gap of 1.24 eV, which was achieved by an enhanced intramolecular charge transfer (ICT) effect. In the OSC device, despite a low energy loss of 0.509 eV, an impressive short‐circuit current density of 25.3 mA cm⁻² is still recorded, which is the highest value for all OSC devices. The high 10.9 % PCE of the NBG‐based OSC demonstrates that the design and application of ultra‐narrow materials have the potential to further improve the PCE of OSC devices.     

Synthesis and characterization of fluorene and cyclopentadithiophene‐based copolymers exhibiting broad absorption for photovoltaic devices

In this study, two low bandgap copolymers composed of fluorene (Fl), cyclopentadithiophene (CDT), and 4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole (DBT) were synthesized, and their optical, electrochemical, and photovoltaic (PV) characteristics were investigated for applications in PV devices. The feed ratio of the Fl and CDT moieties was modulated to tune the electronic structures and resulting optical properties of the polymers. In the copolymeric structures, the Fl‐CDT unit absorbs the short‐wavelength UV/vis regions, and the CDT‐DBT (or Fl‐DBT) unit with strong intramolecular charge transfer characteristics covers the long‐wavelength visible regions. P1 exhibited a wide UV absorption spectrum covering the UV and entire visible region in the range of 300–800 nm, and P2 showed absorption covering from 300 to 700 nm. UV/vis and electrochemical studies confirmed the desirable highest occupied molecular orbital/lowest unoccupied molecular orbital levels of the copolymers with bandgaps of 1.62–1.86 eV, enabling efficient electron transfer and a high open‐circuit voltage when blending them with fullerene derivatives. When the polymers were blended with [6,6]phenyl‐C₆₁‐butyric acid methyl ester, P1 exhibited the best device performance with an open‐circuit voltage of 0.66 V, short‐circuit current of 4.92 mA cm^?2, and power conversion efficiency of 1.13% under Air Mass 1.5 Global (AM 1.5G, 100 mW cm^?2) illumination. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A Stable,Non‐Corrosive Perfluorinated Pinacolatoborate Mg Electrolyte for Rechargeable Mg Batteries

Mg batteries are a promising energy storage system because of the physicochemical merits of Mg as an anode material. However, the lack of electrochemically and chemically stable Mg electrolytes impedes the development of Mg batteries. In this study, a newly designed chloride‐free Mg perfluorinated pinacolatoborate, Mg[B(O₂C₂(CF₃)₄)₂]₂ (abbreviated as Mg‐FPB ), was synthesized by a convenient method from commercially available reagents and fully characterized. The Mg‐FPB electrolyte delivered outstanding electrochemical performance, specifically, 95 % Coulombic efficiency and 197 mV overpotential, enabling reversible Mg deposition, and an anodic stability of up to 4.0 V vs. Mg. The Mg‐FPB electrolyte was applied to assemble a high voltage, rechargeable Mg/MnO₂ battery with a discharge capacity of 150 mAh g^?1.     

Design,Synthesis, and Photovoltaic Characterization of a Small Molecular Acceptor with an Ultra‐Narrow Band Gap

The design of narrow band gap (NBG) donors or acceptors and their application in organic solar cells (OSCs) are of great importance in the conversion of solar photons to electrons. Limited by the inevitable energy loss from the optical band gap of the photovoltaic material to the open‐circuit voltage of the OSC device, the improvement of the power conversion efficiency (PCE) of NBG‐based OSCs faces great challenges. A novel acceptor–donor–acceptor structured non‐fullerene acceptor is reported with an ultra‐narrow band gap of 1.24 eV, which was achieved by an enhanced intramolecular charge transfer (ICT) effect. In the OSC device, despite a low energy loss of 0.509 eV, an impressive short‐circuit current density of 25.3 mA cm⁻² is still recorded, which is the highest value for all OSC devices. The high 10.9 % PCE of the NBG‐based OSC demonstrates that the design and application of ultra‐narrow materials have the potential to further improve the PCE of OSC devices.     

A Stable,Non‐Corrosive Perfluorinated Pinacolatoborate Mg Electrolyte for Rechargeable Mg Batteries

Mg batteries are a promising energy storage system because of the physicochemical merits of Mg as an anode material. However, the lack of electrochemically and chemically stable Mg electrolytes impedes the development of Mg batteries. In this study, a newly designed chloride‐free Mg perfluorinated pinacolatoborate, Mg[B(O₂C₂(CF₃)₄)₂]₂ (abbreviated as Mg‐FPB ), was synthesized by a convenient method from commercially available reagents and fully characterized. The Mg‐FPB electrolyte delivered outstanding electrochemical performance, specifically, 95 % Coulombic efficiency and 197 mV overpotential, enabling reversible Mg deposition, and an anodic stability of up to 4.0 V vs. Mg. The Mg‐FPB electrolyte was applied to assemble a high voltage, rechargeable Mg/MnO₂ battery with a discharge capacity of 150 mAh g^?1.     

A Metal–Organic Compound as Cathode Material with Superhigh Capacity Achieved by Reversible Cationic and Anionic Redox Chemistry for High‐Energy Sodium‐Ion Batteries

Although sodium‐ion batteries (SIBs) are considered as alternatives to lithium‐ion batteries (LIBs), the electrochemical performances, in particular the energy density, are much lower than LIBs. A metal–organic compound, cuprous 7,7,8,8‐tetracyanoquinodimethane (CuTCNQ), is presented as a new kind of cathode material for SIBs. It consists of both cationic (Cu^II↔Cu^I) and anionic (TCNQ⁰↔TCNQ⁻↔ TCNQ²⁻) reversible redox reactions, delivering a discharge capacity as high as 255 mAh g⁻¹ at a current density of 20 mA g⁻¹. The synergistic effect of both redox‐active metal cations and organic anions brings an electrochemical transfer of multiple electrons. The transformation of cupric ions to cuprous ions occurs at near 3.80 V vs. Na⁺/Na, while the full reduction of TCNQ⁰ to TCNQ⁻ happens at 3.00–3.30 V. The remarkably high voltage is attributed to the strong inductive effect of the four cyano groups.