熔纺聚氨酯系中空纤维膜的结构与性能

将聚氨酯/聚偏氟乙烯/聚乙二醇(PU/PVDF/PEG)熔融共混纺丝制得中空纤维膜,对纤维膜的微孔结构与性能进行研究,分析影响其水通量衰减的因素。结果表明:所得纤维膜具有界面及非界面微孔结构;随着水通量工作环境的变化,膜孔结构发生相应变化,表现出压力及温度响应性能;而经热处理后,所得膜部分微孔闭合,水通量下降;随测试时间延长,膜结构趋于致密化,水通量衰减。     

An efficient nanofiltration membrane based on blending of polyethersulfone with modified (styrene/maleic anhydride) copolymer

In this study, styrene–maleic anhydride (SMA) copolymer was modified by ring opening reaction of its anhydride groups with diethanolamine (DEA). The modified SMA copolymer was blended in different concentrations (2.5, 4 and 5.5 %) with Polyethersulfone (PES) to improve the hydrophilicity of PES membranes and the corresponding blend membrane was prepared through phase inversion. The influence of SMA copolymer on morphology, mechanical properties, water flux, rejection and anti-fouling properties of blend membrane were investigated. The modified SMA and their composition were confirmed by FT-IR and ¹HNMR techniques. The asymmetric structure of membrane was revealed by SEM. The water flux and contact angle results show that the hydrophilicity of membrane surface was increased by addition of SMA copolymer. The better anti-fouling properties of the PES/modified SMA blend membranes in comparison with the PES membrane also confirmed that the hydrophilicity of blend membrane enhances.     

A review on hollow fiber membrane module towards high separation efficiency: Process modeling in fouling perspective

Hollow fiber microfiltration (MF) and ultrafiltration (UF) membrane processes have been extensively used in water purification and biotechnology. However, complicated filtration hydrodynamics wield a negative influence on fouling mitigation and stability of hollow fiber MF/UF membrane processes. Thus, establishing a mathematical model to understand the membrane processes is essential to guide the optimization of module configurations and to alleviate membrane fouling. Here, we present a comprehensive overview of the hollow fiber MF/UF membrane filtration models developed from different theories. The existing models primarily focus on membrane fouling but rarely on the interactions between the membrane fouling and local filtration hydrodynamics. Therefore, more simplified conceptual models and integrated reduced models need to be built to represent the real filtration behaviors of hollow fiber membranes. Future analyses considering practical requirements including complicated local hydrodynamics and nonuniform membrane properties are suggested to meet the accurate prediction of membrane filtration performance in practical application. This review will inspire the development of high-efficiency hollow fiber membrane modules.     

ZIF-8 based polysulfone hollow fiber membranes for natural gas purification

Mixed matrix membranes (MMMs) have received worldwide attention for natural gas purification due to their superior performance in terms of permeability and selectivity. The zeolitic imidazole framework-8 (ZIF-8) blended polysulfone (PSf) membranes have been fabricated for natural gas purification. ZIF-8 was selected due to its low cost, remarkable thermal and chemical stabilities, and tunable microporous structure. The neat PSf hollow fiber membrane and mixed matrix hollow fiber membranes incorporated with the various ZIF-8 loadings up to 1.25% were fabricated. The prepared membranes were evaluated using field emission scanning electron microscopy (FESEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), and gas separation performance. The low loading of ZIF-8 nanoparticles to the MMM improved thermal stability and glass transition temperature and yielded low surface roughness. MMMs were tested using pure gases with a significant improvement of 36% in CO₂ permeability and 28% in CO₂/CH₄ selectivity compared to the neat membrane. However, the high ZIF-8 loading reduced the separation performances. Moreover, CO₂/CH₄ selectivity decreased at elevated pressure (8 and 10 bar) due to CO₂-induced plasticization. Previously, the incorporation of ZIF-8 particles has primarily been subjected to the fabrication of flat sheet membranes, whereas this work focused on hollow fiber membranes which are rarely investigated. Hence, the promising results obtained at low feed pressure in this study demonstrated the potential of ZIF-8 based hollow fiber membrane for natural gas purification.     

超亲水聚偏氟乙烯中空纤维膜的制备及性能

采用超声辅助接枝聚合技术, 将甲基丙烯酸缩水甘油酯(GMA)接枝到聚偏氟乙烯(PVDF)膜表面, 制备PVDF-g-GMA膜; 再利用氨基诱导环氧基团发生开环反应, 将苏氨酸(Thr)接枝到PVDF-g-GMA膜表面, 制备了具有两性离子结构表面的PVDF-g-GMA-Thr膜. 通过衰减全反射傅里叶变换红外光谱(ATR-FTIR)、 X射线光电子能谱(XPS)、 接触角测试仪、 场发射扫描电子显微镜(FESEM)和牛血清白蛋白(BSA)过滤实验等系统研究了改性前后PVDF膜表面的化学组成、 润湿性能、 表面形貌和抗污染性能. 研究结果表明, 随着PVDF-g-GMA接枝Thr反应时间的增加, PVDF-g-GMA-Thr膜的亲水性能明显提高, 接触角从90°降为0°, 呈现出超亲水性能. 同时PVDF-g-GMA-Thr膜的水通量明显提高, 当Thr诱导开环反应时间为12 h时, PVDF-g-GMA-Thr膜的水通量高达686 L/(m ²·h), 与PVDF原膜相比, 水通量提高了204.5%. 在BSA的过滤测试中, 与PVDF膜相比, PVDF-g-GMA-Thr膜呈现出良好的截留性能和抗污染性能, BSA截留率从42%提高到84%,水通量恢复率从53%提高到87%, 不可逆污染率从47%降到12%, 表明通过接枝Thr构筑两性离子结构表面可以有效减小膜污染.     

中空纤维复合膜

中空纤维复合膜是分离膜的一种,它是由两种(或两种以上)不同的材料采用一定的制备工艺复合而成的,其优点是将中空纤维的结构特点(如自支撑等)和复合膜的分离优势(如高选择性高通量等)有机结合.本文首先介绍了中空纤维复合膜的基膜及复合层所用到的材料(或添加材料),并按照中空纤维复合膜的结构特点对其进行了简单的分类,并重点论述了中空纤维复合膜的制备设备及工艺.最后论述了中空纤维复合膜在渗透汽化、气体分离和纳滤等领域的研究进展和应用情况,指出中空纤维复合膜需要继续深入的研究内容.     

Mitigated membrane fouling in an SMBR by surface modification

Fouling is a major obstacle in membrane processes applied in membrane bioreactor. To improve the antifouling characteristics of polypropylene hollow fiber microporous membranes (PPHFMMs) in a submerged membrane bioreactor (SMBR), the PPHFMMs were surface modified by NH₃, CO₂ plasma treatment, photoinduced graft polymerization of acrylamide and acrylic acid. The structural and morphological changes on the membrane surface were characterized by X-ray photoelectron spectroscopy (XPS), attenuated total reflection-Fourier transform infrared spectroscopy (FT-IR/ATR) and field emission scanning electron microscopy (FE-SEM). The change of surface wettability was monitored by contact angle measurements. The results of XPS and FT-IR/ATR clearly indicated the successful modification on the membrane surface. The static water contact angle of the modified membrane reduced obviously. The antifouling characteristics of the modified membranes in an SMBR were evaluated. The modified membranes showed better filtration performances in the submerged membrane bioreactor than the unmodified one, and the acrylic acid-grafted membrane presented the best antifouling characteristics. The results demonstrated that (1) the surface carboxyl-containing membranes were better than the surface amido-containing membranes; (2) surface-grafted membranes were better than the plasma-treated membranes.     

Surface modification of microporous polypropylene membranes by the grafting of poly(γ-stearyl-l-glutamate)

A polypeptide, poly(γ-stearyl-l-glutamate) (PSLG), was grafted on the surface of hydrophobic polypropylene hollow fiber membranes through the ring opening polymerization of N-carboxyanhydride (NCA) of γ-stearyl-l-glutamate initiated by amino groups which was generated by ammonia plasma. X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FT-IR), together with water contact angle and bovium serum albumin adsorption measurements were used to characterize the modified membrane surface. The XPS and FT-IR spectra demonstrated that polypeptide was actually grafted on the membrane surface despite of the low degree of graft polymerization due to the hydroxyl groups on the membrane surface. To subject the ammonia plasma-treated membrane with γ-(aminopropyl)triethanoxysilane (γ-APS) which can react with hydroxyl groups and leave amino groups, the degree of graft polymerization could be improved. The bovium serum albumin adsorption measurement was conducted to further examine the surface properties of modified and original membranes. Potential applications of the PSLG grafted membranes are expected for enantiomer separation and/or enzyme immobilization.     

聚全氟乙丙烯中空纤维膜研究

以聚全氟乙丙烯(FEP)为成膜聚合物,复合无机粒子为成孔剂,邻苯二甲酸二辛酯(DOP)为稀释剂,采用熔融纺丝工艺制备得到FEP中空纤维膜.分析和讨论了不同成膜体系对FEP中空纤维膜热性能、动态力学性能和力学性能的影响,并对膜的纯水通量和孔径分布进行表征.用扫描电子显微镜(SEM)观察了膜的横断面和表面形貌.结果表明,所得FEP中空纤维膜为由溶出微孔和界面微孔组成的海绵状孔结构.随着成孔剂含量的增加,成孔剂在成膜体系中分散程度变差,容易发生团聚,最终导致膜孔径变大,孔径分布变宽.成孔剂和稀释剂对FEP中空纤维膜的热性能和动态力学性能影响较小.当FEP含量增加到70 wt％时,膜表面容易形成一层致密层,降低了膜的通透性.     

Microscopic behavior of polyvinylpyrrolidone hydrophilizing agents on phase inversion polyethersulfone hollow fiber membranes for hemofiltration

In some biomedical applications, hollow fiber membranes are highly demanded with desirably asymmetric structures, characterized by a dense selective inner skin with which the blood is in contact and supported by porous outer-layer. In this work, such membranes have been successfully prepared by appropriately adjusting membrane manufacturing parameters. Different molecular weights of polyvinylpyrrolidones (PVPs) were used as the hydrophilizing additives for membrane spinning in order to examine their underlying effects on membrane physicochemical properties, morphological structure, solute rejection behavior and hemofiltration performance. Numerous state-of-the-art characterizations on the resultant membranes showed that the hollow fiber membranes spun with the PVP having a molecular weight of 360K as the additive have the most hydrophilic, smooth and highly net negative charged inner surfaces. These membranes also exhibit the best hemofiltration performance in terms of the characteristically least fouling behavior with a normalized flux above 90%, the highest retention of serum albumin for more than 90%, and the best clearance for the simulated β₂-microglobulin toxin in blood waste.     

Preparation and characterization of inorganic hollow fiber membranes

Inorganic hollow fiber membranes were prepared by spinning a polymer solution containing suspended aluminum oxide (Al₂O₃) powders to a hollow fiber precursor, which is then sintered at elevated temperatures. In spinning these hollow fiber precursors, polyethersulfone (PESf), N-methyl-2-pyrrolidone (NMP), and polyvinyl pyrrolidone (PVP) were used as a polymer binder, a solvent, and an additive, respectively. The inorganic hollow fiber membranes prepared were characterized using scanning electron microscope (SEM), gas permeation techniques Coulter porometer, and gravimetric analysis. Some primary factors affecting the structure and performance of the membranes such as the sintering temperature and the ratio of the aluminum oxide to the PESf polymer binder were studied extensively. The prepared inorganic membranes show an asymmetric structure, which is similar to the conventional polymeric membranes prepared from the same phase-inversion technique. The inorganic hollow fiber membrane with a higher porosity and better mechanical strength could be prepared by blending the spinning solution with a smaller amount of aluminum oxide powder.     

PREPARATION OF ASYMMETRIC POLYETHERKETONE FLAT AND HOLLOW FIBER MEMBRANES FOR GAS SEPARATION USING ACETIC ACID BASED COAGULANTS

Membranes for gas separation have developed significantly in the last twenty years,however,there is still a need for high temperature and chemically resistant membranes that exhibit good selectivity and gas permeability.Our study examines the fundamental properties of polyetherketone (PEK,a thermally stable and chemically resistant polymer) membranes prepared using concentrated sulphuric acid (98% H_2SO_4) as the solvent.Non-solvents used in the work included acetic acid,ethanol,methanol,glycerol,and wat...     

SURFACE MODIFICATION OF POLYPROPYLENE MICROPOROUS MEMBRANE BY TETHERING POLYPEPTIDES

Two kinds of polypeptides were tethered onto the surface of polypropylene microporous membrane （PPMM） through a ring opening polymerization of L-glutamate N-carboxyanhydride initiated by amino groups which were introduced by ammonia plasma and y-aminopropyl triethanoxysilane treatments. X-ray photoelectron spectroscopy （XPS）, attenuated total reflectance Fourier transform infrared spectroscopy （FT-IR/ATR）, scanning electron microscopy （SEM）, together with water contact angle measurements were used to characterize the modified membranes. XPS analyses and FT-IR/ATR spectra demonstrated that polypeptides are actually grafted onto the membrane surface. The wettability of the membrane surface increases at first and then decreases with the increase in grafting degrees of polypeptide. Platelet adhesion and murine macrophage attachment experiments reveal an enhanced hemocompatibility for the polypeptide modified PPMMs. All these results give evidence that polypeptide grafting can simultaneously improve the hemocompatibility as well as reserve the hydrophobicity for the membrane, which will provide a potential approach to improve the performance of polypropylene hollow fiber microporous membrane used in artificial oxygenator.     

Preparation and characterization of polyvinylidene fluoride (PVDF) hollow fiber membranes

Polyvinylidene fluoride (PVDF) hollow fiber membranes were prepared by dry/wet and wet phase inversion methods. In spinning these PVDF hollow fibers, dimethylacetamide (DMAc) and polyvinyl pyrrolidone (PVP) were used as a solvent and an additive, respectively. Water was used as the external coagulant. Water or ethanol was used as the internal coagulants. The membranes were characterized in terms of water flux, molecular weight cut-off for the wet membranes. Gas permeation fluxes and effective surface porosity were determined by a gas permeation method for the dried membranes. The cross-sectional structures were examined by scanning electron microscopy. The effects of polymer concentration, air-gap, PVP molecular weight, PVP content in the polymer dope, and the internal coagulant on the permeation properties and membrane structures were examined. Highly permeable PVDF hollow fiber membranes could be prepared from a polymer dope containing low molecular weight PVP and using ethanol as the internal coagulant.     

Polyethylene Glycol Grafting on Polypropylene Membranes for Anti-fouling Properties

Polyethylene glycol (PEG) chains with different lengths were covalently bonded to polypropylene membranes by means of RF plasma polymerisation of acrylic acid (pp-Aac) followed by mono-amino PEG attachment in liquid phase. Two reactor configurations were tested for the plasma deposition of ppAAc in order to obtain high retention of carboxylic groups in the deposited thin films. A best configuration was assessed evaluating the membrane surface modifications by means of water droplet adsorption time and contact angles measurements, attenuated total reflection (ATR) spectroscopy and X-ray photoelectron spectroscopy (XPS) analysis. PEG chains were covalently bonded to the best plasma modified membranes and the resulting anti-fouling properties were evaluated.     

PPESK纺丝液相分离行为与气体分离膜结构性能的关系

以含二氮杂萘酮结构的聚芳醚砜酮(PPESK)为制膜材料纺制了中空纤维气体分离膜,通过浊点滴定和线性浊点关联式(LCP关系式)计算,对PPESK三元纺丝液体系的相分离行为进行了研究,得到了PPESK三元纺丝液体系相图的相平衡曲线;并由PPESK/N,N-二甲基乙酰胺(DMAc)/γ-丁内酯(GBL)和PPESK/DMAc/丙酸(PA)体系相分离数据计算了PPESK的θ溶剂中GBL和PA与DMAc的比例.结果表明,在PPESK/DMAc/PA和PPESK/DMAc/H2O体系中,浊点滴定实验得到的相平衡曲线与依据LCP关系式计算得到的相平衡曲线吻合;体系热力学性质稳定的纺丝液体系易于制备出结构致密、选择性高的中空纤维气体分离膜;非溶剂添加剂(NSA)/DMAc混合溶剂的θ组成对膜性能有至关重要的影响,NSA/DMAc高于θ组成时,膜性能发生突变,NSA/DMAc低于θ组成时,制得的膜性能良好;力学性能测试表明PPESK中空纤维膜具有良好的机械强度.     

Preparation of electrically enhanced forward osmosis (FO) membrane by two-dimensional MXenes for organic fouling mitigation

In this work, a conductive thin film composite forward osmosis (TFC-FO) membrane was firstly prepared via vacuum filtering MXenes nanolayer on the outer surface of polyethersulfone membrane followed by interfacial polymerization in the other side. Moreover, its feasibility of mitigating organic fouling under electric field was evaluated. Results indicated that the addition of MXenes greatly reduced the electric resistance of membrane from 2.1 × 10¹² Ω to 46.8 Ω, enhanced the membrane porosity and promoted the membrane performance in terms of the ratio of water flux to reverse salt flux. The modified TFC-FO membrane presented the optimal performance with 0.47 g/m² loading amount of MXenes. Organic fouling experiments using sodium alginate (SA) and bovine serum albumin (BSA) as representative demonstrated that the introduction of MXenes could effectively enhance the anti-fouling ability of TFC-FO membrane under the electric field of 2 V. The interelectron repulsion hindered organic foulants attaching into membrane surface and thus effectively alleviated the membrane fouling. More importantly, the modified TFC-FO membrane showed good stability during the fouling experiment of 10 h. In all, our work proved that introducing MXenes into the porous layer of support is feasible to alleviate organic fouling of FO membrane.     

Influence of diazonium-induced surface grafting on PES NF membrane fouling reduction in algal-rich water treatment

The algae bloom phenomenon incurs a major challenge to conventional drinking water treatment processes due to the discharges of a large amount of intracellular pollutant and odor compounds in the water sources. Membrane processes have been considered as promising technologies to treatment of algal-rich water due to complete algal cell rejection however, its application has been limited by membrane fouling. In this work, the high-performance loose antifouling PES NF membranes were fabricated using diazonium-induced grafting and applied for treating real algal effluent. The modified membranes exhibited complete algal dye removal and turbidity removal throughout the long-term filtration. Also, the coupling and radically modified membranes can be able to removed COD by up to 90% and 88%, respectively, while a removal efficiency of 24% was observed for bare membrane. It is worth noting that, a relative smooth behavior in permeate flux by loose modified membranes during prolonged algal dye filtration, demonstrating exceptional anti-fouling property of membranes. In addition, the fouled modified membranes were effectively recovered by water flushing. Both loose modified membranes exhibited excellent resistance in the strongly acidic environment. These high performance antifouling NF membranes affords an innovative methodology toward the treatment of algal-rich water.     

季胺盐对共混聚酰亚胺膜气体除湿性能的影响

季胺盐对共混聚酰亚胺膜气体除湿性能的影响;共混改性;聚酰亚胺;季胺盐;亲水性;除湿     

具有抗菌性能的载药复合微纳米纤维的制备及其结构和性能表征

利用静电纺丝技术制备了一种具有抗菌性能的氧化锌(ZnO)/聚乳酸(PLA)/聚己内酯(PCL)载药微纳米纤维膜,并通过扫描电子显微镜(SEM)、X射线衍射(XRD)和傅里叶变换红外光谱(FTIR)分别对复合膜的表面形态、元素组成和化学结构进行表征。通过抗菌实验评价了复合膜的抗菌性能,用紫外分光光度计测试复合膜在体外的药物释放行为。结果显示,以物理共混的方式将ZnO和氢溴酸高乌甲素(LAH)成功载入复合微纳米纤维;与PLA/PCL复合微纳米纤维膜相比,ZnO/PLA/PCL复合微纳米纤维膜表现出更好的抗菌效率。当ZnO含量为10%(wt)时,复合微纳米纤维膜具有最佳的抗菌性能;药物释放性能结果表明,ZnO/PLA/PCL复合微纳米纤维膜具有良好的药物缓释性能。