Determination of vitamin D2 in emulsified nutritional supplements by solid-phase extraction and column-switching high-performance liquid chromatography with UV detection

This paper deals with a method for solid-phase extraction of trace amounts of vitamin D2 (VD2, 19 ng/g) from emulsified nutritional supplements, which contain 50 kinds of compounds, followed by column-switching high-performance liquid chromatography (HPLC) with UV detection at 265 nm. VD2 is present at 1000-20,000,000 times lower concentration than other components. Bond Elut C18 cartridge was chosen as for the emulsified nutritional supplements after comparison with eight other types. A sample solution was applied to the solid-phase extraction cartridge and VD2 was eluted by methanol followed by HPLC. The effects of sample pH, eluent composition and eluate volume on the retention and elution of VD2 on Bond Elut C18 cartridge were examined. The resulting method was simple, rapid (analysis time: approximately 20 min), sensitive (detection limit: approximately 0.1 ng per injection (200 microl) at a signal-to-noise ratio 3:1), and reproducible (relative standard deviation: approximately 6.2%, n=5). The calibration graph for VD2 was linear in the range of 0.1-3 ng per injection (200 microl). Recovery of VD2 was approximately 80% by the standard addition method.     

Determination of vitamin K1 in emulsified nutritional supplements by solid-phase extraction and high-performance liquid chromatography with postcolumn reduction on a platinum catalyst and fluorescence detection

Determination of small amounts of vitamin K1 (0.8 microg/g) in nutritional supplements with high fat content (20 mg/g) was performed by solid-phase extraction and high-performance liquid chromatography (HPLC) with fluorescence detection after reduction on a platinum oxide catalyst. The concentration ratio of plant oils to vitamin K1 (0.8 microg/g) was about 25,000:1. A sample solution was applied to a solid-phase extraction cartridge and vitamin K1 was eluted with ethanol, followed by HPLC. The proposed method was simple, rapid (analysis time: ca. 12 min), sensitive [detection limit: ca. 0.1 pg per injection (100 microl) at a signal-to-noise ratio of 3:1], highly selective and reproducible [relative standard deviation: ca. 1.3%. (n=5)]. The calibration graph of vitamin K1 was linear in the range of 0-2 pg per injection (100 microl). Recovery of vitamin K1 was over 90% by the standard addition method.     

Sample preparation for routine high-performance liquid chromatographic determination of retinol palmitate in emulsified nutritional supplements by solid-phase extraction using monosodium L-glutamate as dissolving agent

Retinol palmitate (vitamin A, 73.3 microg/g) in an emulsified nutritional supplement was determined by solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with fluorescence detection (excitation 350 nm, emission 480 nm) using monosodium L-glutamate as a dissolving agent to obtain higher recovery of vitamin A from the emulsified sample solution. A Bond Elut C2 cartridge (500 mg) was chosen for SPE after comparison with 16 other types. A sample solution was applied to a conditioned Bond Elut C2 cartridge and then vitamin A was eluted with ethanol followed by HPLC. The proposed method was simple, rapid (sample preparation time by SPE: ca. 8 min, retention time: ca. 8 min), sensitive [detection limit: ca. 0.1 pg/injection (100 microl) at a signal-to-noise ratio of 3:1], highly selective and reproducible (relative standard deviation (RSD): ca. 2.9% (n = 5), between-day RSD ca. 3.7 (5 days). The recovery of vitamin A was over 90% by the standard addition method.     

Simultaneous sample preparation for high-performance liquid chromatographic determination of Vitamin A and β-carotene in emulsified nutritional supplements after solid-phase extraction

Determination of small amounts of the fat-soluble species Vitamin A (VA) (2.5 μg/g) and β-carotene (9 μg/g) from emulsified nutritional supplements containing 50 kinds of co-existing compounds and a fat content between 2000 and 8000 times higher was performed by solid-phase extraction (SPE) and high-performance liquid chromatography (HPLC) with fluorescence detection set at ex. 350 nm and em. 480 nm, and visible detection at 450 nm using an Inertsil ODS 80A (5 μm) analytical column. Mobile phases of methanol-ethanol (50:50) and acetonitrile-ethanol (70:30) were used for the both vitamins. A Bond Elut C₁₈ cartridge was chosen for SPE after comparison with eight other types of SPE cartridge. Retention time of VA and β-carotene was 7 and 8 min, respectively, giving a limit of detection of ca. 0.1 ng per injection at a signal-to-noise ratio 3:1. Recoveries of VA and β-carotene were over 90% by the standard addition method. Relative standard deviation of VA and β-carotene were ca. 2.9 (n=5) and 2.3% (n=5), respectively.     

Use of nucleic acids in the mobile phase for the determination of ascorbic acid in foods by high-performance liquid chromatography with electrochemical detection

The sodium salts of amino acids, nucleic acids and organic acids were examined in a new mobile phase for the determination of ascorbic acid (AA) in foods. It was possible to use disodium guanosine-5'-monophosphate (GMP) (20 mM GMP, pH 2.1) in a new mobile phase after comparison of five mobile phases. The proposed method is simple, rapid (analysis time: ca. 6 min), sensitive (detection limit: ca. 0.1 ng per injection (5 microl) at a signal-to-noise ratio of 3), highly selective and reproducible [relative standard deviation: ca. 2.7% (n=7)]. The calibration graph of AA was linear in the range of 0.1 to 50 ng per injection (5 microl). Recovery of AA was over 90% by the standard addition method.     

Use of an amino acid in the mobile phase for the determination of ascorbic acid in food by high-performance liquid chromatography with electrochemical detection

The possibility of using monosodium L-glutamate (MSG) (20 mM MSG, pH 2.1) in the mobile phase for the determination of ascorbic acid (AA) in foods by high-performance liquid chromatography (HPLC) with electrochemical detection was examined. The hydrodynamic voltammogram of AA and the background current were also examined. The applied potential was set at 400 mV versus an Ag/AgCl reference electrode. It was demonstrated that MSG was a useful mobile phase for the determination of AA in foods. This paper also examines the stability of AA under various conditions in order to optimize HPLC conditions and the pre-run sample stabilization. The proposed method is simple, rapid (analysis time: approximately 6 min), sensitive (detection limit: approximately 0.1 ng per injection (5 microl) at a signal-to-noise ratio of 3), highly selective and reproducible (relative standard deviation: approximately 2.5%, n=7). The calibration graph of AA was linear in the range 0.1-50 ng per injection (5 microl). Recovery of AA was over 90% by the standard addition method.     

Determination of pharmaceutical residues in waters by solid-phase extraction and large-volume on-line derivatization with gas chromatography-mass spectrometry

This work presents a modified method to analyze selected pharmaceutical residues (clofibric acid, ibuprofen, carbamazepine, naproxen, ketoprofen and diclofenac) in water samples. Various solid-phase extraction cartridges were investigated. The newly developed Oasis HLB (polystyrene-divinylbenzene-N-vinyl pyrrolidone terpolymer) solid-phase extraction (SPE) cartridge provides the optimal sample extraction results. The analytes were then identified and quantitatively determined by gas chromatography-mass spectrometry (GC-MS) via on-line derivatization in the injection-port using a large-volume (10 microl) sample injection with tetrabutylammonium (TBA) salts. This injection-port derivatization technique provides sensitivity, fast and reproducible results for pharmaceutical residues analysis. Mass spectra of butylated derivatives and tentative fragmentation profiles are proposed. Molecular ions and some characteristic ions were used as the quantitation ions to obtain maximum detection sensitivity and specificity. The quantitation limits of these compounds ranged from 1.0 to 8.0 ng/l in 500 ml tap water samples. Recovery of these residues in spiked various water samples ranged from 50 to 108% while RSD ranged from 1 to 10%. The selected analytes were detected in concentrations of 30 to 420 ng/l in wastewater treatment plant effluent and river water samples.     

Solid-phase microextraction with on-fiber derivatization for the analysis of anti-inflammatory drugs in water samples

A sensitive and solvent-free procedure for the determination of non-steroidal acidic anti-inflammatory drugs in water samples was optimized using solid-phase microextraction (SPME) followed by on-fiber silylation of the acidic compounds and gas chromatography-mass spectrometry (GC-MS) determination. Microextraction was carried out directly over the filtered water samples using a polyacrylate fiber. Derivatization was performed placing the SPME fiber, loaded with the extracted analytes, in the headspace of a vial containing 50 microl of N-methyl-N-(tert-butyldimethylsilyl)-trifluoroacetamide (MTBSTFA). Derivatives were desorbed for 3 min in the GC injector. Influence of several parameters in the efficiency of microextraction (volume of sample, time, pH, type of fiber coating, etc.) and derivatization steps (time, temperature and volume of MTBSTFA) was systematically investigated. In the optimal conditions an excellent linearity over three orders of magnitude and quantification limits at the ng/l level (from 12 to 40 ng/l) were achieved. The proposed method was applied to the determination of acidic compounds in sewage water and results compared to those obtained using solid-phase extraction (SPE) followed by the derivatization of the compounds in the organic extract of the solid-phase extraction cartridge.     

High-performance liquid chromatographic determination of phenolic compounds in rice

A method has been developed for the determination of 6'-O-feruloylsucrose, 6'-O-sinapoylsucrose, ferulic acid, sinapinic acid, p-coumaric acid, chlorogenic (3-caffeoylquinic) acid, caffeic acid, protocatechuic acid, hydroxybenzoic acid, vanillic acid, and syringic acid in rice. The rice samples were extracted with 70% ethanol, filtered, and defatted. The defatted aqueous solution was subjected to solid-phase extraction using a C18 silica gel cartridge; no analyte was lost in this procedure. The 70% acidic methanol elution was analyzed directly by HPLC and HPLC-ESI-MS. Phenolic compounds were separated with a C18 reversed-phase column by gradient elution using 0.025% trifluoroacetic acid in purified water (A)--acetonitrile (B) (0 min, 5% B; 5 min, 9% B; 15 min, 9% B; 22 min, 11% B; and 38 min, 18% B) as the mobile phase at a flow rate of 0.8 ml/min. Detection limits ranged from 0.10 to 0.35 ng per injection (5 microl). Relative standard deviations of 0.22-3.95% and recoveries of 99-108% were obtained for simultaneous determination of these phenolic compounds. This method was applied to analysis of phenolic compounds in brown rice and germinated brown rice soaked in 32 degrees C water for varying durations.     

Determination of domoic acid in seawater and phytoplankton by liquid chromatography-tandem mass spectrometry

Domoic acid (DA) is an algal neurotoxin produced by diatoms primarily of the genus Pseudo-nitzschia and is responsible for the human intoxication syndrome known as amnesic shellfish poisoning. A method has been developed to determine DA in seawater and phytoplankton matrices by liquid chromatography-tandem mass spectrometry for both quantitation and confirmation purposes. Sample extraction and clean-up was achieved on a C18 solid-phase extraction (SPE) cartridge. An acidic condition is critical for retaining hydrophilic DA on the cartridge. Direct injection of SPE eluate for analysis is recommended in order to avoid loss of DA by drying with heat prior to resuspension and injection. DA was quantified using the fragments produced from the protonated DA ion through multiple reaction monitoring (MRM). Recoveries exceeded 90% for all seawater samples spiked with DA and approximated 98% of toxin standard added to cultured phytoplankton material. Acceptable reproducibility (ca. 5% or less) was obtained for all intra-day and inter-day samples. The detection limit was 30 pg/ml level with a 20 microl injection volume, which demonstrated the value of this method for not only confirming DA production by minimally toxic phytoplankton species, but also for investigating the potentially important role of dissolved DA in marine food webs.     

High-performance liquid chromatographic method for simultaneous determination of enantiomers of 5-dimethylsulphamoyl-6,7-dichloro-2-dihydrobenzofuran-2, carboxylic acid and its N-monodemethyl metabolite in monkey plasma and urine after chiral derivatization

A quantitative method for the simultaneous high-performance liquid chromatographic (HPLC) resolution and determination of the enantiomers of 5-dimethylsulphamoyl-6,7-dichloro-2,3-dihydrobenzofuran-2-carboxyl ic acid, a new diuretic, and its N-monodemethylated metabolite in monkey plasma and urine is described. The method includes diethyl ether extraction of the samples and S-(-)-alpha-methylbenzylamide derivatization of the extract, followed by reversed-phase solid-phase extraction and injection of the resulting diastereoisomers onto a reversed-phase HPLC column. Baseline separation was obtained. The assay showed linearity over the range 0.1-50 micrograms/ml of plasma and 0.25-500 microliters of urine, with a lower limit of detection of ca. 0.01 micrograms/ml for each of the enantiomers. The method is adequate for pharmacokinetic and enantioselective disposition studies of both the diuretic and its metabolite.     

Trace level analysis of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and its biodegradation intermediates in liquid media by solid-phase extraction and high-pressure liquid chromatography analysis

The use of solid-phase extraction for the analysis of liquid media containing low microg/L levels of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), mononitroso-RDX (MNX), dinitroso-RDX (DNX), and trinitroso-RDX (TNX) is examined. Aqueous samples (100 mL) consisting of water and a microbiological basal medium are spiked with known concentrations of RDX, MNX, DNX, and TNX. The compounds are extracted from the liquid media using a Porapak RDX cartridge and then eluted from the cartridge with 5 mL of acetonitrile. The eluent is concentrated to 1 mL before analysis by high-pressure liquid chromatography (HPLC). The method detection limits for RDX are 0.1 microg/L in water and 0.5 microg/L in the basal medium after a 100-fold concentration. For MNX, DNX, and TNX, the method detection limits are approximately 0.5 microg/L in water and approximately 1 microg/L in the basal medium after a 100-fold concentration. Interferences in the basal medium and a contaminant in the standard made quantitation for MNX and TNX, respectively, is less accurate below the 1 microg/L level. Solid-phase extraction of the liquid media gave good recoveries of nitramines and nitroso intermediates from a microbiological basal medium, allowing HPLC detection of RDX and the nitroso intermediates in the low microg/L (ppb) range.     

Routine high-performance liquid chromatographic determination of ascorbic acid in foods using L-methionine for the pre-analysis sample stabilization

The possibility of use of phosphoric acid (0.2% v/v, pH 2.1) in the mobile phase and co-existing compounds present in foods as the dissolving agent for the pre-analysis sample stabilization were examined for the routine determination of ascorbic acid (AA) in foods by high-performance liquid chromatography (HPLC) with electrochemical detection (ED). The applied potential was set at 400 mV versus an Ag/AgCl reference electrode. It was demonstrated that 0.2% v/v phosphoric acid was the useful mobile phase and l-methionine was the most effective dissolving agent for the pre-run sample stabilization of AA in foods after comparison with other amino acids and water-soluble vitamins. The proposed method was simple, rapid (retention time @ ca. 4 min), sensitive (detection limit: ca. 0.1 ng per injection (5 μl) at a signal-to-noise ratio of 3), highly selective and reproducible (relative standard deviation (R.S.D.); 2.5% (n=7), between-day R.S.D.: 3.7% (5 days)). The calibration graph of AA was linear in the range of 0.1-12.5 ng per injection (5 μl). Recovery of AA was over 90% by the standard addition method. Relationship between structure of compounds and the stability of AA was also examined.     

高效液相色谱-串联质谱法测定蜂蜜中残留的19种喹诺酮类药物

建立了高效液相色谱-电喷雾串联质谱联用测定蜂蜜中恩诺沙星、环丙沙星、诺氟沙星、氧氟沙星、双氟沙星、恶喹酸、氟甲喹、沙拉沙星、司帕沙星、丹诺沙星、氟罗沙星、马波沙星、伊诺沙星、奥比沙星、吡哌酸、培氟沙星、洛美沙星、西诺沙星和萘啶酸等19种喹诺酮类药物残留的方法。比较酸性溶液阳离子固相萃取(PCX柱)、近中性缓冲溶液反相固相萃取（HLB柱）和碱性溶液阴离子固相萃取(PAX柱)3种不同提取净化方法的提取效果,最终选择使用碱性溶液溶解蜂蜜样品,强阴离子固相萃取柱一步富集净化。以甲醇和0.1%甲酸溶液作为流动相,C18作为分析色谱柱,采用梯度洗脱方式进行液相色谱分离,选择离子反应监测模式检测19种喹诺酮类药物,内标方法定量。在1～100 μg/L范围内,19种喹诺酮类药物的线性相关系数均大于0.991。通过实际样品的添加回收试验,方法的定量限（S/N=10）为1.0 μg/kg,3个添加水平的回收率为71%～118%,相对标准偏差为4.2%～6.7%。     

Solid-phase microextraction coupled with gas chromatography-ion trap mass spectrometry for the analysis of haloacetic acids in water

Headspace solid-phase microextraction (SPME) was studied as a possible alternative to liquid-liquid extraction for the analysis of haloacetic acids (HAAs) in water. The method involves derivatization of the acids to their ethyl esters using sulphuric acid and ethanol after evaporation, followed by headspace SPME with a polydimethylsiloxane fibre and gas chromatography-ion trap mass spectrometry (GC-IT-MS). The derivatization procedure was optimized: maximum sensitivity was obtained with esterification for 10 min at 50 degrees C in 30 microl of sulphuric acid and 40 microl of ethanol. The headspace SPME conditions were also optimized and good sensitivity was obtained at a sampling temperature of 25 degrees C, an absorption time of 10 min, the addition of 0.1 g of anhydrous sodium sulfate and a desorption time of 2 min. Good precision (RSD lower than 10%) and detection limits in the ng l(-1) range (from 10 to 200 ng l(-1)) were obtained for all the compounds. The optimized procedure was applied to the analysis of HAAs in tap water and the results obtained by standard addition agreed with those of EPA method 552.2, whereas discrepancies due to matrix interferences were observed using external calibration. Consequently, headspace SPME-GC-IT-MS with standard addition is recommended for the analysis of these compounds in drinking water.     

Evaluation and characterization of a commercial immunosorbent cartridge for the solid-phase extraction of phenylureas from aqueous matrices

The behavior and main characteristics of a commercial immunosorbent (IS) cartridge for the solid-phase extraction of phenylureas are determined in this work. The measured capacity for the analyte-antigen (isoproturon) in a new cartridge is 215 ng and, after more than 100 adsorption-desorption cycles, the remaining capacity still is approximately 70 ng, demonstrating the good stability of the bonded antibody and the interesting possibility of extensive cartridge reuse. Only isoproturon and diuron are specifically retained in this sorbent. The weak nonspecific retention of other pesticides, including other phenylureas, can be avoided by increasing the sample volume during the loading step. Thus, a very selective and sensitive method for the determination of isoproturon and diuron in natural and potable waters is developed by loading a 50-mL sample adjusted to pH 7.4 in the IS cartridge, eluting with methanol-water (60:40, v/v), and analyzing the eluate by high-performance liquid chromatography with UV detection. The clean chromatograms, low detection limits (approximately 0.1 micro g/L), and good precision (< 5%) obtained with this rapid and simple method demonstrate that immunoaffinity extraction can be an excellent alternative for sample preparation in the environmental monitoring of particular pesticides in water matrices.     

Quantitative and pharmacokinetic analysis of naloxone in plasma using high-performance liquid chromatography with electrochemical detection and solid-phase extraction

In this study we present a method for measuring naloxone in plasma after intravenous and oral administration of naloxone to humans, in order to study its pharmacokinetic profile. The method consists of a solid-phase extraction step followed by detection on a high-performance liquid chromatographic (HPLC) system equipped with an electrochemical dual-electrode detector. The extraction step employs cyanopropyl columns optimized for naloxone extraction to allow for elution of naloxone by the HPLC mobile phase; this eluate is then directly injected in the HPLC instrument. The HPLC system employs a radial compression phenyl column with a mobile phase containing 18% (v/v) acetonitrile and pentanesulfonic acid as ion-pairing agent; this system shows extraordinary high plate counts for naloxone. The detection limit is 3 ng (signal-to-noise ratio = 3) free naloxone per ml plasma. Following intravenous injection of 30 mg naloxone hydrochloride in two subjects, it was possible to determine the free naloxone concentration in the plasma for 8 h, more than four times the half-life of naloxone in plasma in humans.     

Determination of free and total catecholamines in human urine by HPLC with fluorescence detection

A simple and highly sensitive method for the determination of free and total (free + conjugated) catecholamines (norepinephrine, epinephrine and dopamine) in human urine is described which employs HPLC with fluorescence detection. Conjugated catecholamines (sulfate form) are hydrolyzed by a sulfatase-mediated reaction to the corresponding free amines. After cation exchange chromatography on a Toyopak IC-SP S cartridge, catecholamines and isoproterenol (internal standard) in urine samples were converted into the corresponding fluorescent compounds by reaction with 1,2-diphenylethylenediamine. These compounds were separated within 8 min on a reversed phase column with isocratic elution using a mixture of water, methanol and acetonitrile containing a Tris-hydrochloric acid buffer (pH 7.0). The detection limit for each catecholamine is ca 2 fmol per 100 microL injection volume.     

Development and optimization of a method for the analysis of Brazilein by HPLC with electrochemical detection

The aim of this study was to establish an easy and accurate method for the determination of Brazilein in plant samples due to its potential pharmacological activities. High-performance liquid chromatography (HPLC) with electrochemical detection (ED) was used for the assay of Brazilein in this study for the first time. Crucial influence parameters including concentration of dodecane-1-sulfonic acid sodium salt (DSASS), inorganic modifier, tetrabutyl-ammonium hydroxide solution (TBAOH), and applied potential of proposed method were investigated. The proposed method is simple, rapid (analysis time: approximately 10 min), sensitive [(detection limit: 0.6 ng per injection (20 microl) at a signal-noise ratio 3:1)], highly selective and precise (intra- and inter-day precisions were within 5%, n = 7). The calibration graph of Brazilein was linear in the range 0.6-150 ng per injection 20 microl. Recovery of Brazilein was over 92% by standard addition method.     

High-performance liquid chromatographic determination of mitoxantrone in liposome preparations using solid-phase extraction and its application in stability studies

A method for the determination of the entrapped mitoxantrone in liposome preparations was developed. The method consists of a solid-phase extraction procedure followed by HPLC analysis. A C₁₈ cartridge was used for solid-phase extraction and 0.5M methanolic HCl was used for elution. The extraction demonstrated a good separation of the mitoxantrone from the phospholipid. A C₁₈ column and a mobile phase containing acetonitrile-0.01 M monopotassium phosphate (40:60) with the pH adjusted to 3.0 with orthophosphoric acid were employed. The detection wavelength was 242 nm. The HPLC method was stability indicating and was applied to determine the degradation of the entrapped mitoxantrone in liposomes. A pseudo-first-order reaction was found for the degradation of the entrapped mitoxantrone. The half-life of the mitoxantrone decreased with increasing pH of the medium. The results demonstrate that the proposed method is satisfactory for the determination of the stability of mitoxantrone in liposome preparations.