等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

酵母对抑制剂耐受的系统分析

纤维素生产乙醇的关键问题之一是水解产生的抑制性物质对乙醇发酵具有明显的抑制效应,因而引起了国内外研究者的广泛关注.研究发现,在抑制剂存在下,酵母在基因表达水平,蛋白水平和代谢物水平都有相应的耐受响应,且这些响应错综复杂.从系统角度运用组学的方法研究这一体系将有助于全面深入了解酵母的耐受机制.本文综述了系统研究的思路和方法在酵母对抑制剂耐受方面的研究状况;对主要研究手段和成果进行了回顾;并对酵母发酵乙醇系统分析的前景进行了展望.     

Miniaturized electrochemical sensors and their point-of-care applications

Most of the current analytical methods depend largely on laboratory-based analytical techniques that require expensive and bullky equipment,potentially incur costly testing,and involve lengthy detection processes.With increasing requirements for point-of-care testing(POCT),more attention has been paid to miniaturized analytical devices.Miniaturized electrochemical(MEC)sensors,including different material-based MEC sensors(such as DNA-,paper-,and screen electrode-based),have been in strong demand in analytical science due to their easy operation,portability,high sensitivity,as well as their short analysis time.They have been applied for the detection of trace amounts of target through measuring changes in electrochemical signal,such as current,voltage,potential,or impedance,due to the oxidation/reduction of chemical/biological molecules with the help of electrodes and electrochemical units.MEC sensors present great potential for the detection of targets including small organic molecules,metal ions,and biomolecules.In recent years,MEC sensors have been broadly applied to POCT in various fields,including health care,food safety,and environmental monitoring,owing to the excellent advantages of electrochemical(EC)technologies.This review summarized the state-of-the-art advancements on various types of MEC sensors and their applications in POCT.Furthermore,the future perspectives,opportunities,and challenges in this field are also discussed.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Anisotropy of dielectric relaxation in crystal form II of poly(vinylidene fluoride)

The anisotropy of the crystalline relaxation (α relaxation) in oriented poly(vinylidene fluoride) in crystal form II has been studied. The dielectric increment Δε is analyzed on the basis of the two-site model. A linear relation between Δε/χξ and cos²θ is obtained, where χ is the degree of crystallinity, ξ is the ratio of the internal field to the applied field, and θ is the angle between the applied electric field and the molecular axis. The dipole moment changes direction only along the molecular axis in the relaxation in crystal form II; the molecular motion cannot be explained by chain rotation around the molecular axis. Possible models for the α relaxation are proposed: change in conformation with internal rotation can occur in the crystalline chains, and defects in the crystalline regions play an important role in the α relaxation.     

Les phenomenes de relaxation non isotherme dans les copolymeres ethylene-acetate de vinyle—I. Courants de depolarisation thermique

Depolarization thermocurrent curves for ethylene-vinyl acetate copolymers, previously polarized by the thermoelectret effect at a temperature higher than the glass transition temperature, have been compared with dielectric loss curves described in the literature, in order to establish a possible relation between thermocurrents and the intrinsic relaxation phenomena. The two main peaks observed correspond to loss peaks described in dielectric measurements and result from primary and secondary dipolar relaxation, i.e. α and β type relaxation, respectively. We systematically used a partial polarization method consisting of polarizations in restricted temperature zones during a slow linear cooling of the sample, to describe the specific properties of these peaks. In this manner, we showed that the β relaxation, poorly resolved by dielectric measurements, consists of three discrete components having comparable activation energies, each of them presenting a distribution of the characteristic relaxation time. On the other hand, the amplitude of the α relaxation was found to be one order of magnitude higher than that of the β relaxation. It was characterized by a dipole concentration dependence of the activation energy and also presented an important distribution of characteristic relaxation times.     

Phases confirmation of cloudy Silwet L-77 aqueous solution by dielectric relaxation spectroscopy

<正>The phase transition of Silwet L-77(a kind of siloxane surfactant) dilute aqueous solution with temperature was investigated by dielectric relaxation spectroscopy.In the initial heating process,a dielectric relaxation was found at about 10~6 Hz,which was considered as the interface polarization ascribed to the interface between water and liquid phases(W and L_1).With the temperature increasing further,a new dielectric relaxation was observed at about 10~4 Hz,which was assigned to the appearance of liquid crystal phase(L_α).According to the dielectric parameters fitted by Cole-Cole equation,the coexistence temperature of W,L_1 and L_αwas determined at about 37.0℃.     

铜离子配位下的聚氧乙烯受限结晶行为研究——缺陷引起的熔点下降

利用铜离子(Cu2+)对聚氧乙烯(PEO)的配位作用所形成的对分子链运动的束缚,研究了链段受限下PEO的结晶和熔融行为.首先利用宽频介电松弛谱(BDS)对受限条件下PEO的松弛行为进行表征,结果表明,加入铜离子后PEO的β-过程和γ-过程的特征松弛时间都变长,说明PEO的链段协同运动和主链扭转运动都变得更加困难;松弛时间为评价受限程度提供了定量的依据.DSC的测试结果表明,受限条件下PEO的玻璃化转变温度(Tg)升高,同时出现冷结晶现象,说明Cu2+配位作用确实对PEO的链段运动产生了束缚作用;同时PEO的结晶度和熔点都随着铜离子含量的提高而降低.WAXD结果表明,CuBr2在共混物中没有发生结晶,同时PEO的晶型没有发生改变.利用AFM进一步研究了PEO/CuBr2共混物薄膜的结晶形貌,发现在不同Cu2+含量的共混物中PEO都形成伸直链晶体,片晶厚度没有变化,说明熔点的降低并非是片晶厚度变化所导致.但是AFM的结果却显示螺位错晶体的数量随着Cu2+含量的提高明显增加.可以认为,在Cu2+配位受限下的PEO体系中,晶体缺陷应是引起熔点下降的主要原因,和金属等其它晶体材料的情况有着类似效应.     

Dielectric relaxations and electrical conductivities of poly(alkyl methacrylates) under high pressure

Dielectric properties of four methacrylate polymers (methyl, ethyl, n-butyl and n-octyl) were studied in the frequency range 0.0001 cps–300 kcps at temperatures above and below the glass transition temperature and at various pressures up to 2500 atm. At temperatures well above T_g a single relaxation peak (α′ peak) was observed in the case of the higher n-alkyl methacrylates. However, this peak was split into two peaks, α and β, with decrease in temperature or increase in pressure. The molecular motions corresponding to the α and the β relaxation processes are the micro-Brownian motions of amorphous main chains and of flexible side chains, respectively. From the temperature and the pressure dependence of the average dielectric relaxation time of these polymers the single relaxation process (the α′ process) was attributed to the micro-Brownian motion of the main chain coupled with that of the side chain. The effects of temperature and pressure on the d.c. conductivity of these polymers were also studied.     

Influence of molecular arrangement on the γ-ray-irradiation solid-state polymerization of 1-octadecyl vinyl ether with a characteristic polymorphism

The polymorphic behavior of 1-octadecyl vinyl ether was investigated by DSC and X-ray diffraction measurements under various temperatures. In DSC measurement of 1-octadecyl vinyl ether in the temperature range of −30 to approximately 50°C, four transition peaks were observed on heating, whereas three transition peaks appeared on cooling. The phase-transition behavior was investigated by the repeating scanning DSC measurements. It was concluded that this compound exhibited four crystalline modifications: α, sub α, β₀, and β₁. It was confirmed by the temperature-controlled X-ray diffraction measurement that these phase transitions are attributed to the change of crystal systems from hexagonal packing (α form) to a distorted orthorhombic (O⟂′) system (β₁ form) via orthorhombic (O⟂) (sub α form) and intermediate β₀ form, although the β₀ form has not yet been clarified. In the γ-ray-irradiation solid-state polymerization for these crystal forms of this compound, the polymerizability of the sub α form is higher than that of other forms, and that of the α form is lowest. The polymerizability demonstrated an unusual increase at a temperature of −83.6°C, probably because the cationic polymerization mechanism is dominant over that of the free radical. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3845–3853, 1999     

Dielectric and mechanical relaxation processes in methyl acrylate/tri-ethyleneglycol dimethacrylate copolymer networks

The dielectric properties of methylacrylate (MA)/tri-ethyleneglycol dimethacrylate (TrEGDMA) copolymers at different compositions, ranging from 0 to 100, were measured between −120 and 150 °C over the frequency range 0.1 Hz-1 MHz. In the given frequency range, three relaxation processes were detected by dielectric relaxation spectroscopy in homo poly-TrEGDMA and copolymers: the α process associated with the glass transition, and two secondary processes due to localized mobility. In PMA only one secondary process was observed besides the alpha relaxation process. The influence of copolymerization going from PMA, monofunctional softer component with a glass transition determined calorimetrically as 284 K, to poly-TrEGDMA, higher glass transition component, bifunctional, that also forms a dense network due to cross linking, reflects mainly in the alpha process that shifts to higher temperatures and becomes broader. The raise and broadening in the glass transition with TrEGDMA increase was also observed by dynamic mechanical thermal analysis and differential scanning calorimetry. The glass transition temperature of poly-TrEGDMA was not detected calorimetrically but a value of 429 K was estimated from the best fit of the Fox equation. In what concerns the secondary relaxation process detected in poly-TrEGDMA and copolymers at the lowest temperatures, it is related with local twisting motions of ethyleneglycol moieties, being designated as γ relaxation, while the process detected in the medium temperature range is associated with the rotation of the carboxylic groups as in poly(alkyl methacrylates), designated as β relaxation. This process is detected at much lower temperatures in homo PMA in the same temperature region than the above mentioned γ relaxation. The copolymerization influences mainly the α process while the γ process remains almost unaffected in copolymers relative to homo poly-TrEGDMA. The β process is largely determined by the presence o the tri-ethylene glycol dimethacrylate monomeric units even in copolymers with the lowest TrEGDMA content.     

Dielectric relaxation and molecular motion in poly(vinylidene fluoride)

The dielectric properties of poly(vinylidene fluoride) have been studied in the frequency range 10 Hz to 100 kHz at temperatures between ?196 and 150°C. Three dielectric relaxations were observed: the α relaxation occurred near 130°C, the β near 0°C, and the γ near ?30°C at 100 kHz. In the α relaxation the magnitude of loss peak and the relaxation times increased not only with increasing lamellar thickness, but also with decrease of crystal defects in the crystalline regions. In the light of the above results, the α relaxation was attributed to the molecular motion in the crystalline regions which was related to the lamellar thickness and crystal defects in the crystalline phase. In the β relaxation, the magnitude of the loss peak increased with the amount of amorphous material. The relaxation times were independent of the crystal structure and the degree of crystallinity, but increased slightly with orientation of the molecular chains by drawing. The β relaxation was ascribed to the micro-Brownian motions of main chains in the amorphous regions. The Arrhenius plots were of the so-called WLF type, and the “freezing point” of the molecular motion was about ?80°C. The Cole-Cole distribution parameter of the relaxation time α increased almost linearly with decreasing temperature in the temperature range of the experiment. The γ relaxation was attributed to local molecular motions in the amorphous regions.     

Glass transition and enthalpy relaxation of ethylene glycol and its aqueous solution

Differential scanning calorimetry (DSC) and cryomicroscopy were employed to investigate the glass transition and enthalpy relaxation behaviors of ethylene glycol (EG) and its aqueous solution (50% EG) with different crystallization percent. Isothermal crystallization method was used in devitrification region to get different crystallinity after samples quenched below glass transition temperature. The DSC thermograms upon warming showed that the pure EG has a single glass transition, while the 50% EG solution has two if the solution crystallized partially. It is believed that the lower temperature transition represents the glass transition of bulk amorphous phase of EG aqueous solution glass state, while the higher one is related to ice inclusions, whose mobility is restricted by ice crystal. Cryomicroscopic observation indicated that the EG crystal has regular shape while the ice crystal in 50% EG aqueous solution glass matrix has no regular surface. Isothermal annealing experiments at temperatures lower than T_g were also conducted on these amorphous samples in DSC, and the results showed that both the two amorphous phases presented in 50% EG experience enthalpy relaxation. The relaxation process of restricted amorphous phase is more sensitive to annealing temperature.