Study on complexation adsorption behavior of dibenzo-18-crown-6 immobilized on CPVA microspheres for metal ions

Dibenzo-18-crown-6 (DBC) was immobilized on crosslinked polyvinyl alcohol (CPVA) microspheres, resulting in polymer-supported crown ether DBC–CPVA. The complexation adsorption behaviors of DBC–CPVA microspheres towards diverse metal ions were investigated. The experimental results show that among alkali metal ions, the complexation adsorption ability of DBC–CPVA for K⁺ ion is the strongest, and crown ether-metal complex in 1:1 ratio is formed, exhibiting a high adsorption capacity. The adsorption capacities of alkali metal ions on DBC–CPVA are in the order: K⁺ ? Na⁺ > LI⁺ > Rb⁺ > Cs⁺. Among several divalent metal ions, DBC–CPVA exhibits stronger adsorption ability towards Zn²⁺ and Co²⁺ ions, and a “sandwich”-type complex is formed probably in a molar ratio of 2:1 between the immobilized DBC and Zn²⁺ ion as well as between the immobilized DBC and Co²⁺ ion. The adsorption capacities of the several divalent metal ions on DBC–CPVA are in the order: Zn²⁺ > Co²⁺ ? Cd²⁺ > Cu²⁺ > Ni²⁺ > Pb²⁺. The complexation adsorption is exothermic physical physisorption process, and raising temperature leads to the decrease of the adsorption capacity. At the same time, the entropy during the complexation adsorption decreases, so the adsorption process is driven by the decrease of enthalpy.     

Cellulose and chitin nanomaterials for capturing silver ions (Ag+) from water via surface adsorption

The study explores the potential of cellulose nanocrystals (CNC), cellulose nanofibers (CNF) and chitin nanocrystals (ChNC) isolated from bioresidues to remove silver ions from contaminated water. Zeta sizer studies showed negatively charged surfaces for CNC and CNF isolated from cellulose sludge in the acidic and alkaline pHs, whereas ChNC isolated from crab shell residue showed either positive or negative charges depending on pH conditions. Model water containing silver ions showed a decrease in Ag⁺ ion concentration (measured by inductively coupled plasma-optical emission spectrometer; inductively coupled plasma mass spectrometry), after treatment with CNC, CNF and ChNC suspensions. The highest Ag⁺ ion removal was measured near neutral pH for CNC, being 34.4 mg/g, corresponding to 64 % removal. ChNC showed 37 % and CNF showed 27 % removal of silver ions. The WDX (wavelength dispersive X-ray analysis) and XPS (X-ray photoelectron spectroscopy) analysis confirmed the presence of silver ions on the surface of the nanocellulose and nanochitin after adsorption. Surface adsorption on the nanoparticles via electrostatic interactions is considered to be the prominent mechanism of heavy metal ion capture from aqueous medium, with CNC with negative surface charge and negatively charged functional groups being most favourable for the adsorption of positively charged Ag⁺ ions compared to other native bionanomaterials.     

Selective determination of silver in solution by adsorption on a piezoelectric quartz crystal

Electrodeposition of metal ions on the crystal is eliminated by using a specially constructed transistorized oscillator. When tartrate, citrate, EDTA or their mixtures are present, silver adsorption occurs. The frequency change is proportional to the silver concentration in the range 2 × 10^?7?1 × 10^?5 M after adsorption for 10 min from a 1 mM EDTA/3 mM tartrate solution. No significant interferences are caused by other metal ions. On the basis of cyclic voltammetric studies, it is suggested that silver is adsorbed as a silver (I) complex.     

Extraction of trace amounts of silver on various amino-functionalized nanoporous silicas in real samples

Aminopropyl-functionalized mesoporous silicas, NH₂-MCM-41 and NH₂-SBA-15, as absorbents were utilized for rapid extraction, preconcentration and determination of trace amounts of silver. Flow rates of sample and eluent, pH, eluent solution, type, concentration and the least amount of eluent for desorption of silver ions were optimized; moreover, break through volume and the effect of various cationic interferences on the sorption of silver were evaluated. The extraction efficiency of silver ions was greater than 95% for MCM-41-NH₂ and 85% for SBA-15-NH₂ and the limit of detection (LOD) was less than 4 ng mL^?1 for both functionalized mesoporous silicas. The preconcentration factor was greater than 210 and the relative standard deviation (RSD) was <2%. The adsorption capacity of the mesoporous silicas is higher than 143 mg g^?1 for NH₂-MCM-41 and 137 mg g^?1 for NH₂-SBA-15. Under similar experimental conditions the results for these solid phases were compared with each other. NH₂-SBA-15, in spite of larger pore size diameter and adsorption of silver ions in higher flow rates has lower recovery and a higher RSD compared to MCM-41. This method has been applied to determine silver in photographic emulsions and real samples.     

Non-destructive radioanalytical technique in characterization of anion exchangers Amberlite IRN78 and Indion H-IP

The present study deals with characterization of industrial grade anion exchange resins Amberlite IRN78 and Indion H-IP for which non-destructive radiotracer technique using ¹³¹I and ⁸²Br was used. The radioisotopes were used to trace the kinetics of iodide and bromide ion-isotopic exchange reactions taking place in the two resins. It was observed that under identical experimental conditions of 40.0 °C, 1.000 g of ion exchange resins and 0.003 M labeled iodide ion solution for iodide ion-isotopic exchange reaction, the values of specific reaction rate (min^?1), amount of iodide ion exchanged (mmol), initial rate of iodide ion exchange (mmol min^?1) and log K _d were 0.285, 0.544, 0.155 and 12.6 respectively for Amberlite IRN78 resin, which was higher than 0.093, 0.315, 0.029 and 4.9 respectively as that obtained by using Indion H-IP resins. Also at a constant temperature of 40.0 °C, as the concentration of labeled iodide ion solution increases 0.001–0.004 M, the percentage of iodide ions exchanged increases from 68.10 to 74.00 % for Amberlite IRN78 resin, which was higher than the increase of 40.20–42.80 % as observed for Indion H-IP resins. The identical trend was observed for the two resins during bromide ion-isotopic exchange reaction. The overall results indicate that that under identical experimental conditions Amberlite IRN78 resins shows superior performance over Indion H-IP resins.     

Complexation of metal ion with poly(1-vinylimidazole) resin prepared by radiation-induced polymerization with template metal ion

Poly(1-vinylimidazole) (PVI) resin was prepared with Ni²⁺, Co²⁺, or Zn²⁺ as a template to study the adsorption of metal ions. The metal-1-vinylimidazole complex was copolymerized and crosslinked with 1-vinyl-2-pyrrolidone by γ-ray irradiation and the template metal ion was removed by treating the polymer complex with an acid. These PVI resins adsorbed metal ions more effectively than the PVI resin prepared without the template. The number of adsorption sites (As) and the stability constant (K) of Ni²⁺ complex were larger for the PVI resin prepared with the Ni ion template, caused by the smaller dissociation rate constant of Ni ion from the resin. The composition of the Ni²⁺ complex in the resin remained constant. This suggests that the complexation proceeded via a one-step mechanism.     

Investigation of Silver(I) Ion Sensing Property of Ruthenium(II) Thiosemicarbazone Complex Using Coated Graphite and Polymeric Membrane Electrodes

A ruthenium(II) complex [Ru(PPh₃)₂(pytsc)₂] {Hpytsc = pyridine‐2‐carbaldehydethiosemicarbazone, (C₅H₅N)C²(H)=N³‐N²(H)‐C¹(=S)N¹H} has been used as an ion carrier for the selective determination of silver(I) ions in solution. Silver(I) ion‐selective coated graphite based (CGE) and PVC polymeric membrane based (PME) electrodes exhibit Nernstian slope for silver(I) ions over a wide concentration range from 1.0 × 10⁻¹ M to 5.0 × 10⁻⁶ M (with CGE) and 1.0 × 10⁻¹ M to 2.0 × 10⁻⁵ M (with PME). The working pH range of these electrodes has been found to be from 1.2 to 7.2 for CGE and 2.2 to 6.5 for PME. The proposed CGE sensor exhibits better analytical features like sensitivity and selectivity towards different secondary ions in comparison to the corresponding PME with no interference from mercury(II) ions . These electrodes also act as indicator electrodes in potentiometric titration and have been successfully used for the determination of silver content in solution of real samples (1 gm dissolved in 100 mL of dilute nitric acid) such as silver ornaments and thin silver foils. Silver content determined by the use of ion selective electrode was found to vary in the concentration range from 1.20 x 10⁻² M to 7.45 x 10⁻² M and results were found to be comparable with those obtained from the traditional volumetric method of analysis. It is the first report of a metal‐ligand complex used as an ion carrier in ion selective electrode, which is selective for a metal ion other than the one used in the complex.     

Fabrication of New Cellulose-Based Sorbents for Fast and Efficient Removal of Hazardous Al(III) Ions from Their Aqueous Solutions

Cellulose was used as a base polymer in two prepared resins when it was grafted by glycidyl methacrylate (GMA) then immobilized with 8-hydroxyquinoline by two different procedures. The resulting resins were characterized by infrared (IR) spectroscopy, thermogravimetric analysis (TGA), and nitrogen surface area measurements (BET). The two resins were used in the removal of hazardous Al(III) from their aqueous solutions. The present work discussed the preparation and the effect of spacer arms length used in the functionalization steps on the adsorption process. The resin with longer spacer arm showed faster kinetics compared with the other one toward Al(III) ion adsorption. Fast and efficient adsorption of hazardous Al(III) ions from drinking water by these resins indicates their applicability in water treatment applied field. Thermodynamic parameters were calculated for the studied resins and showed that they possess spontaneous exothermic nature. The regeneration efficiencies reached 90 ± 0.5% over three cycles using a mixture of 2 M HCl and 0.5 M HNO₃.     

Application of ion-imprinted polymer synthesized by precipitation polymerization as an efficient and selective sorbent for separation and pre-concentration of chromium ions from some real samples

In this study, a new Cr(III)-imprinted polymer (Cr(III)-IIP) is prepared from CrCl₃·6H₂O, methacrylic acid functional monomer, ethyleneglycoldimethacrylate cross-linking agent, 2,2?-azobisisobutyronitrile radical initiator and 2,2-(azanediylbis (ethane-2,1-diyl))bis(isoindoline-1,3-dione) ligand. To obtain the maximum adsorption capacity, the optimum condition was studied through pH, type and concentration of eluent, IIP weight, sample volume as well as the adsorption and desorption times. The Cr(III) ion content was determined via flame atomic absorption spectrometer. In optimum conditions, the adsorption capacity of the IIP for Cr(III) was obtained to be 74.65 mg g^?1, using 50 mg of IIP and the initial pH solution of 3.0. Both the adsorption and desorption times for quantitative analyses of Cr(III) ions were 15 and 5 min; respectively. After elution of the adsorbed ions by 3 mL of 4 mol L^?1 HNO₃ aqueous solution, the established IIP-based SPE procedure provides a reasonable pre-concentration factor of 100. The IIP-based pre-concentration method provides a low detection limit of 1.7 µg L^?1 with good repeatability (RSD?=?3.22%). Reusability studies confirmed that synthesis IIP is reusable and recoverable up to six cycles. According to the selectivity experiments, it was concluded that the prepared sorbent possesses more affinity toward Cr(III) ions than other ions such as Al³⁺, Pb²⁺, Cu²⁺, Mn²⁺, Fe²⁺, Zn²⁺, and Ni²⁺ ions. To evaluate the potential applicability of the proposed separation method, the pre-concentration and determination of trace amounts of Cr(III) were performed successfully in food samples with complex matrices, a bestial sample (i.e. cow liver) and an herbal product (i.e., broccoli) as real samples.     

Silver modified magnetic carbon nanotubes composite as a selective solid phase extractor for preconcentration and determination of trace mercury ions in water solution

A magnetic composite of silver/iron oxides/carbon nanotubes (Ag/Fe₃O₄/CNTs) was synthesized and used as an adsorbent for the preconcentration of mercury ions in water solutions at room temperature (25°C) in this study. The silver nanoparticles were supported on the magnetic CNTs. The modification enabled the composite had not only a high adsorption capacity for mercury ions (Hg²⁺) but also the magnetic isolation properties. A fast, sensitive, and simple method was successfully developed for the preconcentration and determination of trace amount of Hg²⁺ in water using the synthesized nanocomposite as adsorbent. The mercury concentration was determined by an atomic fluorescence spectrometer (AFS). The experimental conditions such as pH value, extraction temperature, extraction time, sample volume, eluent composition and concentration, sorbent amount, and coexisting ions were investigated for the optimization. A 500 mL of sample volume resulted in a preconcentration factor of 125. When a 200 mL of sample was employed, the limit of detection for Hg²⁺ was as low as 0.03 ng mL^?1with relative standard deviation of 4.4% at 0.1 ng mL^?1 (n = 7). The ease of synthesis and separation, the good adsorption capacity, and the satisfactory recovery will possibly make the composite an attractive adsorbent for the preconcentration of ultratrace Hg²⁺ in waters.     

A Ce3+-imprinted functionalized potassium tetratitanate whisker sorbent prepared by surface molecularly imprinting technique for selective separation and determination of Ce3+

A surface molecular imprinting technology was developed to adsorb Ce(III) ions that showed much higher adsorption affinity and selectivity for than for other metal ions. The batch adsorption process was studied with respect to effects of pH value, residence time, temperature, and initial concentration of Ce(III) ion. The maximum adsorption capacity is 43 mg g^?1 at an initial Ce(III) concentration of 300 mg L^?1 and at a sorbent dosage of 1.0 g L^?1. A Langmuir isotherm fits the experimental data. The imprinted sorbent exhibits a much higher separation and selectivity for the target imprinted ion than the non-imprinted polymer. Cerium ion can be desorbed with 1M hydrochloric acid solution which is also proven by scanning electron microoscopy and X-ray diffraction experiments. The limit of detection is 37 ng mL^?1. The sorbent has been applied to the determination of trace cerium in different environmental samples with satisfactory results.     

Novel Flow Injection/Potentiometric Measurement of Slightly Soluble Salts in Small Volumes: Determination of Solubility Product Constants of Some Silver Salts

Abstract

The flow injection technique is shown to provide fast, reliable and sensitive determination of solubility product constants of silver acetate, silver sulfate, silver oxide, silver bromate and silver chloride in microliter volume samples. Potentiometric detection using electrodes of the first kind and second kind was used for measuring silver ions and chloride ions, respectively. The solubilities were determined from measurement of the silver ion concentration in the saturated solutions. In the case of silver chloride, the solubility product constant was calculated from the concentrations corresponding to the intersection of the silver ion calibration curve and the chloride ion calibration curve, i.e., where the potentials of the two electrodes are equal. Tenth-molar sodium nitrate was used for all solutions to maintain constant ionic strength. At a concentration range of 1.00 × 10^?2 ? 1.00 × 10^?5 M silver, and 1.00 × 10^?2 ? 1.00 × 10^?4 M chloride, a Nernstian response of 60 m V per decade was obtained. At a sampling rate of 50–70 samples per hour, with 50 μl sample injections, high reproducibility of measurements was achieved, with a -pL 2% relative standard deviation in measured concentrations. The scope and applications of this system are discussed.     

Study on the Color Reaction of Silver with 2‐(2‐Quinolylazo)‐5‐Dimethylaminoaniline and its Application

A new chromogenic reagent, 2‐(2‐quinolylazo)‐5‐dimethylaminoaniline (QADMAA) was synthesized. A highly sensitive, selective and rapid method for the determination of silver based on the rapid reaction of silver(I) with QADMAA was developed. In the presence of pH = 6.5 sodium citrate‐sodium hydroxide buffer solution and sodium dodecyl sulfonate (SDS) medium, QADMAA reacts with silver to form a violet complex of a molar ratio 1:2 (silver to QADMAA). The molar absorptivity of the complex is 1.26 × 10⁵ L. mol^?1.cm^?1 at 570 nm. Beer's law is obeyed in the range of 0.01–0.6 μg/mL. The relative standard deviation for eleven replicate samples of 0.2 μg/mL silver is 1.76%. This method was applied to the determination of silver in water with good results.     

Preparation of silver nanoparticles in aqueous solutions in the presence of carbonate ions as stabilizers

Silver nanoparticles are prepared by reducing Ag⁺ ions with sodium borohydride in aqueous solutions containing carbonate ions (5 × 10⁻⁵−1 × 10⁻² mol l⁻¹). It is established that carbonate ions represent an efficient stabilizer that provides nanoparticles with electrostatic protection via the formation of an electrical double layer. The maximum stability of a silver dispersion is observed at a carbonate ion concentration of 1 × 10⁻³ mol l⁻¹. The average size of silver nanoparticles is 10.0 ± 2.5 nm. The formation kinetics of silver nanoparticles is described by an equation for a first-order reaction with a rate constant of 2.3 × 10⁻³ s⁻¹ (±20%).     

Comparative study on lanthanum(III) sorption onto Lewatit TP 207 and Lewatit TP 260

Batch experiments are carried out for the sorption of La(III) onto commercial macroporous resins containing iminodiacetic (Lewatit TP 207) and aminomethylphosphonic acid groups (Lewatit TP 260). The operating variables studied are initial La(III) concentration, pH, temperature and contact time. Since the extraction kinetics were fast, with a mixture of 0.1 g of resin and 5 mL of lanthanum ions 0.5 × 10^?3 mol L^?1 solution, extraction equilibrium was reached within 30 min of mixing. The optimum pH values level for quantitative sorption were between 1.5 and 4.6 with Lewatit 207 and about 5.2 with Lewatit TP 260. The sorption capacities of Lewatit TP 207 and Lewatit TP 260 resins are 114.7 and 106.7 mg g^?1, respectively. Adsorption equilibrium data were calculated for Langmuir and Freundlich isotherms. It was found that the sorption of La(III) on Lewatit TP 207 was better suited to the Langmuir adsorption model while Freundlich adsorption model fitted better sorption on Lewatit TP 260. Thermodynamics data leads to endothermic and spontaneous process. ΔG° decreases with increasing temperature indicating that sorption process of La(III) on both Lewatit TP 207 and Lewatit TP 260 was more favored at high temperature.     

Removal of Lead (II) Ions by Poly(2‐octadecyl butanedioic acid): Isothermal and Kinetic Studies

Poly(2‐octadecyl‐butanedioic acid), prepared from polyanhydride PA‐18, possesses novel heavy metal adsorption characteristics. The adsorption capacity of this water insoluble polymer for lead (II) was substantially higher than other heterogeneous adsorbants and is equivalent to those obtained with homogeneous sorbants. The polymer exhibited pseudo‐second‐order kinetics and nearly complete adsorption of lead occurred in 15 min with initial lead (II) concentrations greater than 100 mg · L^?1. Adsorptive behavior was accurately predicted by the Dubinin‐Radushkevich isotherm model. The mean free energy of adsorption of lead (II) onto poly(2‐octadecyl‐butanedioic acid) was determined to be 31.6 kJ · mol^?1, suggesting an ion exchange component to the adsorption mechanism. Gibb's free energy values for this process indicate that it is spontaneous. Adsorption was relatively independent of pH in the range of 3–5, due to the utilization of the sodium carboxylate form of the chelating groups, and was not influenced by high Na⁺ concentration and moderate concentrations (up to 200 mg · L^?1) of Ca⁺². Lead (II) solutions containing 2000 mg · L^?1 Ca⁺² did reduce the adsorption of 2000 mg · L^?1 lead (II) by 28%.     

Chemically modified kapok fiber for fast adsorption of Pb2+, Cd2+, Cu2+ from aqueous solution

Kapok fiber, a natural hollow fiber with thin shell and large cavity, has rarely been used as adsorbent for heavy metal ions. In this paper, kapok fibers were modified with diethylenetriamine pentaacetic acid (DTPA) after hydrophilicity treatment. The adsorption behavior of the resultant kapok-DTPA influenced by pH, adsorption time and initial concentration of metal ion was investigated. The results demonstrate that adsorption equilibrium was reached within 2 min for Pb²⁺ and Cd²⁺. Adsorption kinetics showed that the adsorption rate was well fitted by pseudo-second-order rate model. The adsorption isotherms were studied, and the best fit was obtained in the Langmuir model. The maximum adsorption capacities of kapok-DTPA were 310.6 mg g^?1 for Pb²⁺, 163.7 mg g^?1 for Cd²⁺, 101.0 mg g^?1 for Cu²⁺, respectively. After eight desorption and re-adsorption loops, the lost adsorption capacities for Pb²⁺ and Cu²⁺ were less than 10 %. Because of the large specific area derived from the hollow fiber structure, kapok-DTPA exhibited much better adsorption capacity compared with many other reported adsorbents based on natural materials.     

Highly Selective and Sensitive Preconcentration of Mercury Ion and Determination by Cold Vapor Atomic Absorption Spectroscopy

Abstract

A simple and selective method based on a sodium dodecyl sulfate (SDS)–coated chromosorb P modified by 2‐mercaptobenzoxazole (MBO) has been developed to selectively separate and concentrate ultra trace amounts of mercury(II) ions for its highly sensitive measurement by cold vapor atomic absorption spectrometry (CVAAS).

The mercury ions were adsorbed quantitatively on SDS‐coated chromosorb due to its complexation with MBO, while the retained Hg²⁺ ions were then stripped from the column with minimal amounts of 2 M nitric acid in acetone. The eluting solution was sent to CV‐AAS for evaluating Hg²⁺ ion content and results indicate that the calibration curve was linear for Hg²⁺ ion in the range of 0.05–85.6 ng mL^?1 and 0.09–9.6 µg mL^?1 of Hg²⁺ ions. Maximum capacity of the SDS‐coated chromosorb modified with 40 mg of the ligand was found to be 498±30 µg of mercury(II), the limit of detection was 0.01 ng mL^?1, and enrichment factors were about 300, which make it suitable it for dilute solution analysis. The method was successfully applied to the determination of Hg²⁺ ion content in real samples.     

Ferric Chloride Complexes in Aqueous Solution: An EXAFS Study

A series of concentrated aqueous solutions of ferric chloride with different chloride:iron(III) ratios has been studied by means of EXAFS to determine the structure around the iron(III) ion of the dominating species in such solutions. The dominating species in dilute acidic aqueous solution of ferric chloride, at less than 1 mmol·dm^?3, are the hydrated iron(III) and chloride ions, while in concentrated aqueous solution and in solutions with an excess of chloride ions, up to 1.0 mol·dm^?3, it is the trans-[FeCl₂(H₂O)₄]⁺ complex. Possible higher chloroferrate(III) or dimeric [Fe₂Cl₆] complexes at room temperature, as proposed in the literature, were not observed in any of the studied solutions in spite of an excess of chloride ions of 1 mol·dm^?3.     

A novel and convenient preparation of antibacterial polyacrylonitrile nanofibers via post-modification using nitrile click chemistry and electrospinning

An efficient, novel and convenient method for the synthesis of modified polyacrylonitrile (PAN) with antibacterial property is reported. The modification of PAN was prepared by a nitrile click chemistry reaction with sodium azide (NaN₃) and silver nitrate (AgNO₃) as catalyst to yield antibacterial polymeric materials with 5-vinyltetrazole units. The results showed that 5-vinyltetrazole units had coordinated with silver ion (Ag⁺). Through the electrostatic spinning technology, the post-modification PAN nanofibers (PAN–Ag⁺ nanofibers) were prepared and the fibers were tested for their antimicrobial properties by the bacterial infection experiment. Afterwards, the antibacterial and stable performance of different proportions of silver ions in PAN nanofibers has been compared. The PAN–Ag⁺ nanofibers are characterized for mechanical and thermomechanical properties, structural analysis, appearance characteristics, as well as the antibacterial properties. And the nanofibers exhibit marvelous chemical stability according to the thermogravimetric analysis. When at 800 °C, the PAN decomposed about 60%, while the decomposition of the PAN–Ag⁺s was 40%. Based on the bacterial infection experiment, PAN–Ag⁺ nanofibers’ antibacterial properties were stronger with the increase of silver ions, such as the number of bacteria clone was smaller and the bacteriostatic ring was larger. Hence, with combination of silver ions, the final polymers show strong antimicrobial properties.