Influence of the substrate material on the properties of pulsed laser deposited thin Li1+xMn2O4−δ films

Thin Li_1+xMn₂O_4−δ films were deposited on several substrate materials (stainless steel, p-doped silicon and glassy carbon) by pulsed laser deposition. To obtain the correct thin film stoichiometries, targets with a different amount of excess lithium were required (Li_1.03Mn₂O₄ + xLi₂O; x = 2.5 and 7.5 mol%). The resulting polycrystalline thin films were characterized with respect to their morphology and electrochemical activity. It was found that only thin Li_1+xMn₂O_4−δ films deposited on stainless steel and glassy carbon showed the typical insertion and deinsertion peaks of Li⁺ during cycling.     

Precursor derived LiMn2O4 thin films as ionic conductor

Thin films of spinel LiMn₂O₄ have been fabricated using a metallorganic precursor. Crystalline films have been deposited on Au substrates to exhibit as the cathode in rechargeable thin film lithium batteries. The nucleation and growth of spinel LiMn₂O₄ crystallites were investigated with heat treatment of the deposited thin films. Film capacity density as high as 22 μAh/cm² was measured for LiMn₂O₄. The film heat treated at 700 °C were cycled electrochemically up to 30 cycles against Li metal without any degradation of the capacity. There were neither open area nor amorphous layers which prevent the Li⁺ions transfer at the boundaries in the LiMn₂O₄ thin film. The microscopic study revealed that (111) planes in the two grains directly bonded at the grain boundary which could proceed the lithium ion intercalation or deintercalation smoothly.     

Characterization of crystallized LiMn2O4 thin films grown by pulsed laser deposition

LiMn₂O₄ thin films were grown on stainless steel substrates at 625°C and 100?mTorr of oxygen by pulsed laser deposition. The deposited film was highly crystallized with an average crystal size of about 260?nm. The initial discharge capacity of the film was about 53.8?µAh?cm^?2?µm^?1 and the capacity decayed at an average rate of about 0.29% per cycle when the film was cycled between 3.0 and 4.5?V vs. Li/Li⁺, with a current density of 20?µA?cm^?2. It was observed that the grains became smaller and the boundaries of grains became obscure after 100 cycles, indicating that manganese dissolution via loss of MnO may be the main factor leading to the capacity fade in pure thin film LiMn₂O₄ electrodes. The apparent diffusion coefficient of Li ions, obtained from cyclic voltammetry scans, was of the order of 10^?12?cm²?s^?1. High charge-transfer resistance was observed at high potentials. Ex-situ X-ray diffraction (XRD) and Raman spectroscopy were used to investigate the structure changes of LiMn₂O₄ thin film with intercalation/de-intercalation of lithium. XRD results revealed a relatively small lattice change with the removal of lithium in crystallized thin film, compared to that of powder LiMn₂O₄ cathode.     

The influence of lithium excess in the target on the properties and compositions of Li<Subscript>1+<Emphasis Type="Italic">x</Emphasis></Subscript>Mn<Subscript>2</Subscript>O<Subscript>4−<Emphasis Type="Italic">δ</Emphasis></Subscript> thin films prepared by PLD

Li–Mn–O thin films were deposited by pulsed laser deposition (PLD) onto stainless steel substrates using targets containing different concentrations of added Li₂O. The influence of the target composition on the stoichiometry of the resulting thin films, the surface morphology and the electrochemical properties was studied. The application of the target with added 7.5 mol% Li₂O results in an almost ideal lithium content, while all films were still oxygen deficient. The thin films were applied as electrodes in Li//Li_1+x Mn₂O_4−δ cells (i.e. model cells for a rechargeable Li-ion battery) and characterized by cyclic voltammetry and galvanostatic charge/discharge experiments. The electrochemical measurements of the thin films confirmed that the thin films can serve as good model systems and that they show a sufficient cyclability.     

Vibrational studies of spinel LixMn2O4 (0.3≤x≤1.0) cathodes

We report on the vibrational properties of spinel LiMn₂O₄ and its electrochemically delithiated forms Li_xMn₂O₄. Raman scattering and infrared absorption spectra have been studied as a function of the delithiation content in the wavenumber range 50–700 cm⁻¹. Results show that lithium ions can be extracted at room temperature to obtain Li_x[Mn₂]O₄ (0.3≤x≤1.0) without disrupting the [Mn₂]O₄ array. The normal modes of the spinel LiMn₂O₄ have been discussed in the O _h ⁷ symmetry and vibrations due to lithium ions with their oxygen neighbors have been identified at ca. 400 cm⁻¹. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Structural and electrochemical effects of cobalt doping on lithium manganese oxide spinel

Pure LiMn₂O₄ and lithium manganese oxide spinels with partial replacement of manganese by cobalt up to 20 mole%, LiCo_xMn_2−xO₄, were prepared. The effect of extended cycling on the crystal structure was investigated. A capacity decrease with increasing cobalt content was observed in the potential range about 4100 mV vs. Li/Li⁺. Cycling behavior is significantly improved, compared to LiMn₂O₄. LiCo_xMn_2−xO₄ is discharged in a single phase reaction in the upper potential range around 4100 mV vs. Li/Li⁺, whereas pure LiMn₂O₄ shows a two phase behavior. LiMn₂O₄ shows a significant broadening of peaks in plots of differential capacity and change in shape of the voltage profile upon extended cycling. LiCo_xMn_2−xO₄ shows neither broadening nor change. Voltage profiles and plots of the differential capacity differ significantly compared to spinels with lithium substitution, Li_1+xMn_2−xO₄. In contrast to Li_1+xMn_2-xO₄, LiCo_xMn_2-xO₄ is discharged in a two step process in the range of 0 ≤ × ≤ 0,5. Paper presented at the 3rd Euroconference on Solid State Ionics, Teulada, Sardinia, Italy, Sept. 15–22, 1996     

Glassy carbon - A promising substrate material for pulsed laser deposition of thin Li1+xMn2O4−δ electrodes

The spinel LiMn₂O₄ is a promising candidate for future battery applications. If used as a positive electrode in a battery, the charging capacity of such a battery element is limited by the formation of a solid electrolyte interphase like layer between the electrolyte and the spinel. To study the electrolyte-electrode interaction during electrochemical cycling, spinel thin films are deposited as model electrodes on glassy carbon substrates by pulsed laser ablation. The obtained polycrystalline oxide thin films show a well defined surface morphology and are electrochemical active. Adhesion of these thin films on glassy carbon is in general poor, but can be improved considerably by a surface pretreatment or adding a thin metallic coating to the substrate prior deposition. The best adhesion is obtained for films deposited on argon plasma pretreated as well as Pt coated glassy carbon substrates. During the electrochemical characterization of Li_1.06Mn₂O_3.8 thin film electrodes, no additional reactions of the substrate are observed independent of the used electrolyte. The best cycle stability is achieved for films on Pt coated glassy carbon substrates.     

Surface modification of LiMn2O4 thin films at elevated temperature

In order to improve the cycle stability of spinel LiMn₂O₄ electrode at elevated temperature, the LiCoO₂-coated and Co-doped LiMn₂O₄ film were prepared by an electrostatic spray deposition (ESD) technique. LiCoO₂-coated LiMn₂O₄ film shows excellent cycling stability at 55 °C compared to pristine and Co-doped LiMn₂O₄ films. The samples were studied by X-ray diffraction, scanning electron microscopy, Auger electron spectroscopy, cyclic voltammetry and electrochemical impedance spectroscopy. The excellent performance of LiCoO₂-coated LiMn₂O₄ film can be explained by suppression of Mn dissolution. On the other hand, the LiCoO₂-layer on the LiMn₂O₄ surface allows a homogenous Li⁺ insertion/extraction during electrochemical cycles and improves its structure stability.     

Small polaron migration in LixMn2O4: From first principles calculations

Migration of small polarons in λ-MnO₂, Li_0.5Mn₂O₄ and LiMn₂O₄ is studied via first principles calculations. Migration energy barriers of single small polaron migrations in λ-MnO₂, Li_0.5Mn₂O₄ and LiMn₂O₄ are 0.22 eV, 0.45 eV and 0.35 eV, respectively. The energy level changes of Mn-3d states along the polaron migration path are analyzed in detail. Results indicate that the activation energy barrier of polaron migration is strongly associated with the energy level shift of Mn-3dz² orbital, which is dependent on the short range structural arrangement of Mn³⁺/Mn⁴⁺ in the crystal. The electrical conduction properties of Li_xMn₂O₄ at room temperature are then discussed.     

Synthesis and pseudocapacitive investigation of LiCr x Mn2-x O4 cathode material for aqueous hybrid supercapacitor

A series of Cr-substituted LiMn₂O₄ samples (LiCr _x Mn_2-x O₄, 0?≤?x?≤?0.3) were synthesized by a urea-assisted combustion method to enhance pseudocapacitive properties of LiMn₂O₄ material in aqueous electrolyte. Their structure and morphology were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The LiCr _x Mn_2-x O₄ and activated carbon (AC) electrode were used as the cathode and anode in hybrid supercapacitors, respectively, which capacitive properties were determined by cyclic voltammetry (CV), galvanostatic charge/discharge test, and electrochemical impedance spectroscopy (EIS) in Li₂SO₄ solution. The results revealed that the partial substitution of Mn³⁺ by Cr³⁺ decreased initial capacity, but it prevented capacity fading. In the working voltage of 0–1.4 V, the AC/LiCr_0.1Mn_1.9O₄ capacitor delivered an initial specific capacitance of 41.6 F g^?1 (based on the total active mass of two electrodes) at a current density of 100 mA g^?1 in 1 M Li₂SO₄ solution. After 1,000 cycles, its capacity loss was only 1.7 %.     

ArF excimer laser deposition of wide-band gap solid electrolytes for thin film batteries

High quality solid electrolyte thin films was grown by pulsed laser deposition (PLD) using a high photon energy ArF excimer laser. Various amorphous thin films were successfully deposited on glass substrates from oxide targets; such as Li₃PO₄, LiBO₂, Li₂SiO₃, Li₂CO₃, Li₂SO₄, Li₂ZrO₃, LiAlO₂, Li₂WO₄ and Ohara glass ceramics. The morphology, optical property and ionic conductivity of these films were examined by optical microscope, UV–VIS spectroscopy and impedance analysis. Dramatic improvement of the film morphology was observed by using a high photon energy laser, while the broken film with many droplets was obtained by using lower ones. Ionic conductivity of the films was examined by impedance spectroscopy and dc polarization method. For example, an ionic conductivity of a Li₃PO₄ film was 4.6 × 10^? 6 S cm^? 1 at 25 °C with activation energy of 0.57 eV. Electronic conductivity measurements revealed that most of the films were pure lithium ion conductors, while a Li₂WO₄ film was a mixed conductor.     

Effects of structural disorder in lithium manganite and titanate oxides

The structures and magnetic states of stoichiometric lithium manganite LiMn₂O₄ and manganites and titanates Li_1.33Mn_1.67O₄ and Li_1.33Ti_1.67O₄ with excess lithium in both the initial (as-synthesized) state and after irradiation by fast (E _eff ≥ 1 MeV) neutrons with a fluence of 2 × 10²⁰ cm⁻² have been studied using neutron diffraction, X-ray diffraction, and magnetic methods. It has been established that the irradiation brings about a noticeable redistribution of manganese, titanium, and lithium cations over nonequivalent tetrahedral (8a) and octahedral (16d) positions of a spinel lattice. This structural disorder causes a radical change in the physical properties of the materials under study. The charge order existing in the initial LiMn₂O₄ sample is destroyed. There arises a strong intersublattice indirect exchange interaction Mn(8a)-O-Mn(16d). The disorder is accompanied by the antiferromagnet-ferrimagnet (LiMn₂O₄) and paramagnet-ferrimagnet (Li_1.33Mn_1.67O₄) magnetic transitions.     

Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.     

Investigation on FR(LT)–FR(HT) phase transition and pyroelectric properties of pulsed laser deposited Pb(Zr0.93Ti0.07)O3 thin films

The preparation process, crystallinity and electrical properties of pulse laser deposited Pb(Zr_xTi_1−x)O₃ (PZT) thin films were investigated in this paper. PZT (x = 0.93) thin film samples deposited at different substrate temperatures were prepared. Si (1 1 0) was the substrate; Ag and YBCO were the top electrode and the bottom electrode respectively. The bottom electrode YBCO was deposited on the Si substrate by pulsed laser deposition (PLD), and then PZT was epitaxially deposited on YBCO also by PLD. After annealing, the top electrode Ag was prepared on PZT by thermal evaporation, and then the Ag/PZT/YBCO/Si structured thin films were obtained. The XRD and the analysis of their electrical characters showed that, when the substrate temperature was elevated from 600 °C to 800 °C, the crystallinity and electrical properties of PZT thin films became better and better, and the F_R(LT)–F_R(HT) phase transition of PZT (x = 0.93) thin films occurred at 62 °C. The PZT film deposited at 800 °C had the best pyroelectric properties, and when the F_R(LT)–F_R(HT) phase transition of this film occurred, the peak value of pyroelectric coefficient (p) was obtained, with a value of 1.96 × 10⁻⁶ C/(cm² K). The PZT film deposited at 800 °C had the highest remnant polarization (P_r) and the lowest coercive field (E_c), with the values of 34.3 μC/cm² and 41.7 kV/cm respectively.     

Improvement of electrochemical performance of all-solid-state lithium secondary batteries by surface modification of LiMn2O4 positive electrode

To improve the electrochemical performance of an all-solid-state In/80Li₂S⋅20P₂S₅ (electrolyte)/LiMn₂O₄ cell, a lithium-titanate thin film was used to coat LiMn₂O₄. The interfacial resistance between LiMn₂O₄ and the electrolyte (measured after initial charging) decreased when the LiMn₂O₄ particles were coated with lithium-titanate. A cell with lithium-titanate-coated LiMn₂O₄ had a higher capacity than a cell with noncoated LiMn₂O₄ for current densities in the range 0.064 to 2.6 mA cm^− 2. Additionally, a cell with coated LiMn₂O₄ retained 96% of the 10th-cycle reversible capacity at a current density of 0.064 mA cm^− 2 after 50 cycles.     

Pulsed laser deposition using diffractively shaped excimer-laser beams

Controlling laser-pulse parameters is an important issue in pulsed laser deposition (PLD). In particular, homogenization of laser beams improves the reproducibility of the PLD process by guaranteeing a uniform intensity distribution and a well-defined energy density of the laser spot on the target. We have integrated a beam-homogenization system into our PLD setup, and here we discuss the results and advantages of using such a system. The optical setup is based on diffractive beam-splitter gratings, which produce a 2×2-mm² flat-top distribution with fluences of the order of 3 J/cm² on the target. We demonstrate the applicability of this technique by depositing thin films of ferromagnetic Ni–Mn–Ga shape-memory alloys. Magnetic and structural characterization, including secondary ion mass spectrometry (SIMS), indicate that nearly stoichiometric composition and crystallization in the desired martensitic phase is obtained for films deposited on Al₂O₃ under optimal conditions. In contrast, the formation of silicide compounds at temperatures above 500 ^°C is detrimental in the deposition of Ni–Mn–Ga films directly on silicon.     

Effect of ultrasonic irradiation on structure and electrochemical properties of LiMn2O4 thin films cathode material for Li-ion micro-batteries

Two kinds of spinel LiMn₂O₄ thin film for lithium ion micro-batteries were successfully prepared on polycrystal Pt substrates by spin coating methods, which were carried out under ultrasonic irradiation (USG) and magnetic stirring (MSG), respectively. The microstructures and electrochemical performance of LiMn₂O₄ thin films were characterized by thermogravimetry analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and galvanostatic charge-discharge measurements. It was found that the crystalline structure of USG samples grew better than that of the MSG samples. At the same time, higher discharge capacity and better cycle stability were obtained for the LiMn₂O₄ thin films of USG at the current density of 50 μAh/cm² between 3.0 and 4.3 V. The 1st discharge capacity was 57.8 μAh/cm²-μm for USG thin films and 51.7 μAh/cm²-μm for MSG thin films. After 50 cycles, 91.4% and 69% of discharge capacity could be retained respectively, indicating that ultrasonic irradiation condition during spin coating was more suitable for preparing spinel LiMn₂O₄ thin films with better electrode performance for lithium ion micro-batteries.     

Gas barrier properties of titanium oxynitride films deposited on polyethylene terephthalate substrates by reactive magnetron sputtering

Titanium oxynitride (TiN_xO_y) films were deposited on polyethylene terephthalate (PET) substrates by means of a reactive radio frequency (RF) magnetron sputtering system in which the power density and substrate bias were the varied parameters. Experimental results show that the deposited TiN_xO_y films exhibited an amorphous or a columnar structure with fine crystalline dependent on power density. The deposition rate increases significantly in conjunction as the power density increases from 2 W/cm² to 7 W/cm². The maximum deposition rate occurs, as the substrate bias is −40 V at a certain power densities chosen in this study. The film's roughness slightly decreases with increasing substrate bias. The TiN_xO_y films deposited at power densities above 4 W/cm² show a steady Ti:N:O ratio of about 1:1:0.8. The water vapor and oxygen transmission rates of the TiN_xO_y films reach values as low as 0.98 g/m²-day-atm and 0.60 cm³/m²-day-atm which are about 6 and 47 times lower than those of the uncoated PET substrate, respectively. These transmission rates are comparable to those of DLC, carbon-based and Al₂O₃ barrier films. Therefore, TiN_xO_y films are potential candidates to be used as a gas permeation barrier for PET substrate.     

Lithiated c-V<Subscript>2</Subscript>O<Subscript>5</Subscript> thin-film as positive electrode for rocking-chair solid-state lithium microbattery

We report for the first time the use of lithiated crystalline V₂O₅ thin films as positive electrode in all-solid-state microbatteries. Crystalline Li_xV₂O₅ films (x ≈ 0.8 and 1.5) are obtained by vacuum evaporation of metallic lithium deposited on sputtered c-V₂O₅. An all-solid-state lithium microbattery of Li_1.5V₂O₅/LiPON/Li exhibited a typical reversible capacity of 50 μAh/cm² in the potential range 3.8/2.15 V which exceeds by far the results known on all-solid-state lithium batteries using amorphous V₂O₅ films and lithiated amorphous Li_xV₂O₅ thin films as positive electrode. Hence, the present work opens the possibility of using high performance crystalline lithiated V₂O₅ thin films in rocking-chair solid-state microbatteries.     

Electric and magnetic properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript> bilayer thin films prepared by pulsed-laser deposition

CoFe₂O₄ (CFO) thin film with highly (111)-preferential orientation was first deposited on the silicon substrate by a pulsed-laser deposition, and then Pb(Zr_0.52Ti_0.48)O₃ (PZT) layers were deposited with different oxygen pressures to form the bilayer CFO/PZT nanocomposite thin films. X-ray diffraction showed that the PZT preferential orientation was strongly dependant on the oxygen pressure. The smooth film surface was obtained after depositing the CFO and PZT layers. The bilayer thin films exhibit good ferromagnetic and ferroelectric properties, and a low leakage current density of 0.004 μA/cm² at 50 kV/cm. The leakage current density curves show loops for the electric polarized field when the electric field reverses. PACS 77.84.Lf; 75.80+q; 81.05.Zx; 81.15.Fg