Deposition of conductive TiN shells on SiO<Subscript>2</Subscript> nanoparticles with a fluidized bed ALD reactor

Conductive TiN shells have been deposited on SiO₂ nanoparticles (10–20 nm primary particle size) with fluidized bed atomic layer deposition using TDMAT and NH₃ as precursors. Analysis of the powders confirms that shell growth saturates at approximately 0.4 nm/cycle at TDMAT doses of >1.2 mmol/g of powder. TEM and XPS analysis showed that all particles were coated with homogeneous shells containing titanium. Due to the large specific surface area of the nanoparticles, the TiN shells rapidly oxidize upon exposure to air. Electrical measurements show that the partially oxidized shells are conducting, with apparent resistivity of approximately ~11 kΩ cm. The resistivity of the powders is strongly influenced by the NH₃ dose, with a smaller dose giving an order-of-magnitude higher resistivity.     

Optical excitation and emission processes of Si-QD/SiO2 multilayer films with different SiO2 layer thicknesses

Si-rich oxide/SiO₂ multilayer films with different SiO₂ layer thicknesses have been deposited by the plasma enhanced chemical vapor deposition technique, and crystallized Si quantum dot (Si-QD)/SiO₂ multilayer films are obtained after annealing at 1100 ^°C. The photoluminescence (PL) intensity of the multilayer films increases significantly with increasing SiO₂ layer thickness, and the PL peak shifts from 1.25 eV to 1.34 eV. The PL excitation spectra indicate that the maximal PL excitation intensity is located at 4.1 eV, and an excitation–transfer mechanism exists in the excitation processes. The PL decay time for a certain wavelength is a constant when the SiO₂ thickness is larger than 2 nm, and a slow PL decay process is obtained when the SiO₂ layer is 1 nm. In addition, the PL peak shifts toward high energy with decreasing temperature only when the SiO₂ layer is thick enough. Detailed analyses show that the mechanism of PL changes from the quantum confinement effect to interface defects with decreasing SiO₂ layer thickness.     

Dry sliding wear behavior of Al-SiO2 composites

Abstract

Al-base composites with different amount of silica (5, 10, 15 and 20 wt.%) were developed using powder metallurgy route and compacts were sintered at 550 °C for 2 h. XRD analysis of all compositions was conducted for phases and amount of the second phase present. Morphology of the composites shows quite uniform distribution of the SiO₂ particles but at higher percentage of SiO₂ particles the clustering starts. Mechanical properties such as uniaxial compressive strength (UCS) and hardness were evaluated and it is seen that among all compositions, composite with 10 wt.% SiO₂ has maximum UCS and hardness. Wear behavior of all composites was studied with sliding distance, applied loads, sliding velocity and composition. All composites show a linear increase in cumulative wear with distance and load. Wear rate with load increases continuously for all compositions, however, composite with 10 wt.% SiO₂ revealed minimum wear rate with distance, sliding velocity and loads. Wear rate with sliding velocity increases sharply after attaining minima at 3 m/s sliding velocity. SEM analysis of wear tracks is in agreement with wear results. Al-10 wt.%SiO₂ also shows minimum wear coefficient values for all loads, however, wear coefficient decreases with load for all compositions.     

Size-Dependent HCl Generation of PVC/SiO2 Micro- and Nanocomposites

In this study HCl generation of polyvinyl (chloride) (PVC)/SiO₂ composites during its combustion was investigated. SiO₂ with different particle sizes were used as HCl absorbers and their HCl uptake ability results were compared to that of CaCO₃. It was found that the amount of released HCl gas during PVC combustion decreased in the presence of SiO₂. The HCl uptake ability of SiO₂ improved with decreasing of its particle size. Although thermogravimetric analysis (TGA) results showed that SiO₂ particles decreased the first thermal degradation temperature (T _onset) of PVC by initiating dehydrochlorination of PVC at lower temperatures, SiO₂ particles had more effective HCl uptaking ability than that of CaCO₃. Scanning electron microscopy (SEM) micrographs showed that some aggregates whose size was less than 100 nm were formed when Si-25 nm was used as filler. When SiO₂ with micron size was added to PVC as filler, more uniform and better distribution of the SiO₂ on the surface was observed.     

Preparation and performance of the polyethylene-supported polyvinylidene fluoride/cellulose acetate butyrate/nano-SiO<Subscript>2</Subscript> particles blended gel polymer electrolyte

The preparation of polyethylene-supported poly(vinylidene fluoride)/cellulose acetate butyrate/nano-SiO₂ particle (PVDF-CAB-SiO₂/PE) blended gel polymer electrolytes (GPEs) is reported here. The electrolyte uptake, mechanical properties, thermal stability, and electrochemical performance of these electrolytes are characterized to evaluate their potential application in lithium-ion batteries (LIBs). The results indicate that the particle size of SiO₂ can be adjusted by the tetraethyl orthosilicate (TEOS) concentration and affects the physicochemical properties of the membrane. By doping 5 wt.% SiO₂ (500 nm) into the PVdF-CAB blended polymer, the porosity of the membrane increases from 40 to 42.3 %, the mechanical strength from 117.3 to 138.7 MPa, the electrolyte uptake from 149 to 195 %, the oxidation decomposition potential from 4.7 to 5.2 V, and the ionic conductivity of the corresponding GPE is improved from 1.16 to 2.98 mS cm^?1 at ambient temperature. The PVDF-CAB-SiO₂/PE-based GPE and the two electrodes are suitably compatible, and the thermal stability is higher than that of the polyethylene (PE) membrane. The LIBs with the as-prepared GPE also exhibit enhanced discharge capacity and cycle stability, indicating the promising application of these GPEs in LIBs.     

Electrochemical lithium storage properties of desert sands

SiO₂ is one of the most promising lithium storage materials for lithium-ion batteries anodes due to its low cost, good environmental compatibility, low working voltage, and high-specific capacity. In this work, the desert sands, which are rich in SiO₂, are investigated as the anode material for lithium-ion batteries. The electrochemical activation, lithium storage capacity, and cycle properties are highly dependent on the particle size distribution of sands. As the average particle sizes of sands gradually decrease, the reversible lithium storage capacity increases from 137 mAh g^?1 (several microns) to 492 mAh g^?1 (several submicrons). The 72 h-milled sands (average particle size: ~1 μm) deliver a stable lithium storage capacity of ~400 mAh g^?1 over 400 cycles with the capacity retention as high as 95%. The reason for the electrochemical activation, lithium storage capacity, and cycle properties of sands associated with their particle size distribution is also discussed.     

Sonoelectrochemical Synthesis of Nano Zinc (II) Complexes with 9-Anthracenecarboxylic Acid: Effect of Current Density and Study of their Photophysical Properties

A new zinc complex, [Zn (9-AC)₂] (1) (9-AC = 9-anthracenecarboxylic acid), was prepared via conventional electrochemical method in a fast and facile process and fully characterized by ¹H NMR, ¹³C NMR, IR spectroscopy and elemental analysis. The nano structures of the same compound were successfully produced by a facile and environment-friendly sonoelectrochemical route at different current densities (0.5, 1.2, 1.8, 2.5 and 3.5 mA/cm²). The new nano-structure particles were characterized by scanning electron microscopy, X-ray powder diffraction, IR spectroscopy and elemental analysis. Thermal stability of single crystal and nano-size samples of the prepared compound was studied by thermogravimetric and differential thermal analysis. The comparison of the effect of current density without and with ultrasonic irradiation on particle size has been investigated in convectional electrochemical and sonoelectrochemical method respectively. The results showed that using ultrasonic irradiation with increasing the current density lead to decrease the particle sizes unlike conventional electrochemical method. In other words, when the current density increase from 0.5 to 3.5 mA/cm², in sonoelectrochemical method, the particle sizes decrease from 100 to 48 nm while, in convectional electrochemical method, the particle sizes increase from 400 to 1200 nm and possible explanation offered. Photoluminescence properties of the nano-structured and crystalline bulk of the prepared complex at room temperature in the solid state have been investigated in detail. The results indicate that the size of the complex particles has an important effect on their optical properties.     

Synthesis,characterization, and thermal stability of SiO<Subscript>2</Subscript>/TiO<Subscript>2</Subscript>/CR-Ag multilayered nanostructures

The controllable synthesis and characterization of novel thermally stable silver-based particles are described. The experimental approach involves the design of thermally stable nanostructures by the deposition of an interfacial thick, active titania layer between the primary substrate (SiO₂ particles) and the metal nanoparticles (Ag NPs), as well as the doping of Ag nanoparticles with an organic molecule (Congo Red, CR). The nanostructured particles were composed of a 330-nm silica core capped by a granular titania layer (10 to 13 nm in thickness), along with monodisperse 5 to 30 nm CR-Ag NPs deposited on top. The titania-coated support (SiO₂/TiO₂ particles) was shown to be chemically and thermally stable and promoted the nucleation and anchoring of CR-Ag NPs, which prevented the sintering of CR-Ag NPs when the structure was exposed to high temperatures. The thermal stability of the silver composites was examined by scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). Larger than 10 nm CR-Ag NPs were thermally stable up to 300 °C. Such temperature was high enough to destabilize the CR-Ag NPs due to the melting point of the CR. On the other hand, smaller than 10 nm Ag NPs were stable at temperatures up to 500 °C because of the strong metal-metal oxide binding energy. Energy dispersion X-ray spectroscopy (EDS) was carried out to qualitatively analyze the chemical stability of the structure at different temperatures which confirmed the stability of the structure and the existence of silver NPs at temperatures up to 500 °C.     

Properties of Natural Rubber Vulcanizates/Nanosilica Composites Prepared Based on the Method of In-situ Generation and Coagulation

Using the characteristics of silica sol dispersing well in water and easy formation of silica gel when the silica sol is heated, by mixing a system of concentrated natural rubber latex and silica sol, the silica sol can in-situ generate SiO₂ particles when heated. After coagulation of the mixed system, natural rubber/nanosilica composites C(NR/nSiO₂) were obtained. The composites C(NR/nSiO₂) and their vulcanizates were studied using a rubber processing analyzer (RPA), dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM). The influence of silica contents on the C(NR/nSiO₂) vulcanizates mechanical properties, cross-linking degree, Payne effect, dissipation factor (tanδ), and the particle size and dispersion of SiO₂ in NR were investigated. The results obtained were compared with the NR/SiO₂ composites based on traditional dry mixing of bale natural rubber and precipitated silica (white carbon black). The results showed that when using a sulfur curing system with a silica coupling agent (Si69) in C(NR/nSiO₂), the vulcanizate had better mechanical properties, higher wet resistance, and lower rolling resistance than those without Si69. In the composites C(NR/nSiO₂) and their vulcanizates, the SiO₂ particles’ average grain diameter was 60 nm, and the good-dispersion of the in-situ generated SiO₂ in the rubber matrix were a significant contribution to the satisfactory properties of C(NR/nSiO₂) composites and their vulcanizates.     

Rapid synthesis of SiO<Subscript>2</Subscript> by ultrasonic-assisted Stober method as controlled and pH-sensitive drug delivery

In this paper, the monodisperse silica nanoparticles were prepared by ultrasonic-assisted Stober method, and it explained that the ultrasonic cavitation effect shortened the reaction time from the original hours to f5 min. The effects of ultrasonic time, ultrasonic power, and stirring speed on the morphology, composition, and specific surface area of silica nanoparticles were investigated by field emission electron microscopy (FE-SEM). The results showed that nanoparticles with the best dispersity and the most uniform morphology were obtained under the optimized conditions (ultrasonic time is 5 min, ultrasonic power is 160 W, and the magnetic stirring speed is 999 rpm). The phase composition of SiO₂ was characterized by high-resolution transmission electron microscopy (HR-TEM), X-ray diffraction (XRD), nano-size/zeta potential analyzer, and Fourier transform infrared spectroscopy (FT-IR). It showed that all typical peaks of samples are in line with the SiO₂ spectrum, the particle size distribution and zeta potential value of the silica is 615?±?35.6 nm and 59.87?±?0.91 mv, respectively, which further verified that the spherical silica nanoparticles with good dispersity can be synthesized in a very short time. Hemolysis test showed that nano-SiO₂ had high blood compatibility and biocompatibility when its concentration was less than 1 mg/mL. Doxorubicin (DOX·HCl) was regarded as a drug model to investigate the drug loading capacity of synthesized SiO₂; the results showed that the drug loading capacity and encapsulation efficiency reached 42.6?±?1.2 and 85.2?±?2.5%, respectively. Furthermore, the drug release experiments fitted well with the Higuichi equation with correlation coefficient (R²) of 0.9984, which further confirmed that the SiO₂/DOX drug delivery system has the controlled release property, and it also displayed pH-responsive behavior (at 96 h, the cumulative release of SiO₂/DOX in PBS solution with pH 7.4, 6.5, and 5.0 was 48.33, 62.31, and 94.86%, respectively). Therefore, this paper provides the possibility for developing more effective, safer, and more targeted controlled drug carriers.     

Au/SiO2纳米复合薄膜的微结构及光吸收特性研究

用多靶磁控溅射技术制备了Au/SiO₂纳米多层薄膜.利用透射电子显微镜以及吸 收光谱对Au/SiO₂复合薄膜的微观结构、表面形貌及光学性能进行了表征和测试 .研究结果表明：单层Au/SiO₂薄膜中Au沉积时间小于10s时，分散在SiO_{2< /sub>中的Au颗粒随Au的沉积时间的延长而增大；当沉积时间超过10s后，Au颗粒的尺寸几乎 不随沉积时间变化，但Au颗粒的形状由网络状结构变为薄膜状结构.［Au(t1关键词： 尺寸效应 纳米复合薄膜 吸收光谱 有效媒质理论}     

Fabrication and characterization of Au/SiO2 nanocomposite films grown by radio-frequency cosputtering

Au/SiO₂ nanocomposite films were prepared on Si wafers by cosputtering of SiO₂ and gold wires. Au/Si atomic ratios in Au/SiO₂ nanocomposite films were varied from 0.53 to 0.92 by controlling the length of gold wire to study the evolution of the crystallization of gold, the size of Au/SiO₂ nanocomposite particles, and the optical properties of as-deposited Au/SiO₂ nanocomposite films. An X-ray photoelectron spectroscopy reveals that Au exists as a metallic phase in the bulk of SiO₂ matrix. Dome-shaped Au/SiO₂ nanocomposite particles and both Au (1 1 1) and (2 0 0) planes were observed in a field-emission scanning electron microscopy and X-ray diffraction studies respectively. With an ultraviolet-visible, absorption peaks of Au/SiO₂ nanocomposite films were observed at 525 nm.     

Controlled synthesis of photoluminescent Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> nanoparticles from metal-organic polymeric precursor

Bi₄Ti₃O₁₂ (BIT) nanoparticles with a narrow average particle size distribution in the range of 11–46 nm was synthesized via a metal-organic polymeric precursor process. The crystallite size and lattice parameter of BIT were determined by XRD analysis. At annealing temperatures >550 °C, the orthorhombic BIT compound with lattice parameters a = 5.4489 Å, b = 5.4147 Å, and c = 32.8362 Å was formed while at lower annealing temperatures orthorhombicity was absent. Reaction proceeded via the formation of an intermediate phase at 500 °C with a stoichiometry close to Bi₂Ti₂O₇. The particle size and the agglomerates of the primary particles have been confirmed by FESEM and TEM. The decomposition of the polymeric gel was ascertained in order to evaluate the crystallization process from TG-DSC analysis. Raman spectroscopy was used to investigate the lattice dynamics in BIT nanoparticles. In addition, investigation of the dependence of the visible emission band around the blue–green color emission on annealing temperatures and grain sizes showed that the effect of grain size plays important roles, and that oxygen vacancies may act as the radiative centers responsible for the observed visible emission band.     

Synthesis of α‐Willemite Nanoparticles by Post‐calcination of Flame‐made Zinc Oxide/Silica Composites

Composite ZnO/SiO₂ nanoparticles were made by flame spray pyrolysis (FSP). Characteristics of the product powder and its crystallization behavior on post‐calcination were evaluated. Polyhedral aggregates of nano‐sized primary particles consisting of ZnO nano‐crystals 1–3 nm in size and amorphous SiO₂ were obtained by FSP. A short residence time in the flame can result in the co‐existence of the ZnO and SiO₂ clusters without substitution or reaction hindering each other's grain growth. There was almost no change in the XRD pattern by calcination at 600 °C for 2 h, suggesting a high thermal stability of the ZnO nano‐crystals in the composite particles. A pure α‐willemite phase was obtained at 900 °C. At this calcination temperature, d_C and d_BET of the powder were 63 and 44 nm, respectively. The nano‐composite structure of the FSP‐made particles can suppress crystalline growth of ZnO during calcination to maintain a high reactivity of ZnO with SiO₂, obtaining pure α‐willemite with high specific surface area at low calcination temperatures.     

Generation of MoS<Subscript>2</Subscript> quantum dots by laser ablation of MoS<Subscript>2</Subscript> particles in suspension and their photocatalytic activity for H<Subscript>2</Subscript> generation

MoS₂ quantum dots (QDs) have been obtained in colloidal suspensions by 532 nm laser ablation (7 ns fwhp/pulse, 50 mJ/pulse) of commercial MoS₂ particles in acetonitrile. High-resolution transmission electron microscopy images show a lateral size distribution from 5 to 20 nm, but a more homogeneous particle size of 20 nm can be obtained by silica gel chromatography purification in acetonitrile. MoS₂ QDs obtained by laser ablation are constituted by 3–6 MoS₂ layers (1.8–4 nm thickness) and exhibit photoluminescence whose λ_PL varies from 430 to 530 nm depending on the excitation wavelength. As predicted by theory, the confinement effect and the larger periphery in MoS₂ QDs increasing the bandgap and having catalytically active edges are reflected in an enhancement of the photocatalytic activity for H₂ generation upon UV–Vis irradiation using CH₃OH as sacrificial electron donor due to the increase in the reduction potential of conduction band electrons and the electron transfer kinetics.     

Thermal conductivity and thermal diffusivity of SiO<Subscript>2</Subscript> nanopowder

A 3ω approach for the simultaneous determination of the effective thermal conductivity and thermal diffusivity of nanopowder materials was developed. A 3ω experimental system was established, and the thermal properties of water and alcohol were measured to validate and estimate the accuracy of the current experimental system. The effective thermal conductivity and thermal diffusivity of the SiO₂ nanopowder with 375, 475, and 575 nm diameters were measured at 290–490 K and at different densities. At room temperature, the effective thermal conductivity and thermal diffusivity of the SiO₂ nanopowder increased with temperature; however, both values decreased as the particle diameter was reduced. An optimum SiO₂ powder density that decreased with decreasing diameter was also observed within the measurement range. The minimum effective thermal conductivity and maximum effective thermal diffusivity were obtained at 85 × 10⁻³ kg/L, when the particle diameter was 575 nm. The optimum densities of the particles with 375 and 475 nm diameters were less than 50.23 × 10⁻³ and 64.82 × 10⁻³ kg/L, respectively.     

Effect of the Calcination Atmosphere on the Structural Properties of the Reduced Fe/SiO2 System

Iron supported systems are frequently used as catalysts in the Fischer–Tropsch synthesis being the Fe⁰ the active phase for the reaction. We have studied the influence of the calcination atmosphere (air or nitrogen) on the iron oxide reducibility and the metallic iron particle size obtained in Fe/SiO₂ system. We have impregnated a silicagel with Fe(NO₃)₃·9H₂O aqueous solution and the solid obtained was calcinated in air or N₂ stream. These precursors, with 5% (wt/wt) of Fe, were characterized by Mössbauer Spectroscopy at 298 and 15 K. Amorphous Fe₂O₃ species with 3 nm diameter in the former, and α-Fe₂O₃ crystals of 48 nm diameter were detected in the last one. Both precursors were reduced in H₂ stream. Two catalysts were obtained and characterized by Mössbauer spectroscopy in controlled atmosphere at 298 and 15 K, CO chemisorption and volumetric oxidation. α-Fe⁰, Fe₃O₄ and Fe²⁺ were identified in the catalyst calcined in air. Instead, only α-Fe⁰ was detected in the catalyst calcined in N₂. The iron metallic crystal sizes were estimated as ≈2 nm for the former and ≈29 nm for the last one. The different oxide crystal sizes, obtained from the diverse calcination atmospheres, have led to different structural properties of the reduced solids. It has been possible to reduce totally the existing iron in an Fe/SiO₂ system with iron loading lower than 10% (wt/wt).     

Structural investigations of Ge nanoparticles embedded in an amorphous SiO2 matrix

Transmission electron microscopy and X-ray photoelectron spectroscopy analyses are performed to investigate Ge nanoparticles embedded in an amorphous SiO₂ matrix. GeSiO thin films are prepared by two methods, sol?Cgel and radio frequency magnetron sputtering. After the deposition, the sol?Cgel films are annealed in either N₂ (at 1 atm and 800 °C) or H₂ (at 2 atm and 500 °C), and the sputtered films in H₂ (at 2 atm and 500 °C), to allow Ge segregation. Amorphous Ge-rich nanoparticles (3?C7 nm size) are observed in sol?Cgel films. Crystalline Ge nanoparticles in the high pressure tetragonal phase (10?C50 nm size) are identified in the sputtered films. The size of the nanoparticles increases with Ge concentration in the volume of the film. At the film surface, the Ge concentration is much larger that in the volume for both sol?Cgel and sputtered films. At the same time, at the film surface, only oxidized Ge is observed.     

Mössbauer and magnetic studies of MFe2O4(M = Co, Ni) nanoparticles

Nanocrystalline MFe₂O₄ (M?=?Co, Ni) particles are synthesized by citrate precursor technique. Mössbauer and magnetic studies are carried out with the CoFe₂O₄ samples having particle sizes of 9, 14 and 30 nm and the NiFe₂O₄ samples having particle sizes of 9, 21 and 30 nm. The intrinsic magnetic parameters are found to vary with the particle size. The magnetic interactions and cation distribution present in these systems influence the room temperature Mössbauer parameters. Ferrimagnetic sextets are observed for all the different particle sizes. The observed reduction of the magnetic hyperfine field values with the decrease in the size of MFe₂O₄ particles are attributed to the intrinsic size effect and the canted spin structure at the surface of the nanoparticles.     

Effects of sintering temperature on the structure and electrochemical performance of Mg<Subscript>2</Subscript>SiO<Subscript>4</Subscript> cathode materials

The objective of the present study was to investigate the effects of sintering temperature on the structure and electrochemical performance of Mg₂SiO₄ cathode materials using sol-gel method. X-ray diffraction and Fourier-transform infrared analysis were used to study the structural properties of the materials. The temperatures applied in the sintering process influenced the structure, morphology, as well as particle size distribution of the Mg₂SiO₄. All samples sintered at temperatures of 900, 1000, and 1100 °C yielded pure Mg₂SiO₄ compounds consisting of orthorhombic crystalline phase with a space group of Pbnm. Particle size and lattice parameters of Mg₂SiO₄ samples increased with the increases of sintering temperature due to an increase of the nucleation and crystal growth rates. The cyclic voltammetry analysis showed the presence of redox reaction. This result shows that the Mg₂SiO₄ material has potential to be used as cathode materials in magnesium rechargeable batteries.