Piezoelectric non-linearity in PbSc0.5Ta0.5O3 thin films

Epitaxial (001)-oriented PbSc_0.5Ta_0.5O₃ (PST) thin films were deposited by pulsed laser deposition. Local piezoelectric investigations performed by piezoelectric force microscopy show a dual slope for the piezoelectric coefficient. A piezoelectric coefficient of 3 pm/V was observed at voltages up to 0.8 V. However, at voltages above 0.8 V, there is a steep increase in piezoelectric coefficient mounting to 23.2 pm/V. This nonlinear piezoelectric response was observed to be irreversible in nature. In order to better understand this nonlinear behavior, voltage dependent dielectric constant measurements were performed. These confirmed that the piezoelectric non-linearity is indeed a manifestation of a dielectric non-linearity. In contrast to classical ferroelectric systems, the observed dielectric non-linearity in this relaxor material cannot be explained by the Rayleigh model. Thus the dielectric non-linearity in the PST films is tentatively explained as a manifestation of a percolation of the polar nano regions.     

Optical constants of Cu(In0.7Ga0.3)5Se8 and Cu(In0.4Ga0.6)5Se8 crystals

Variable angle spectroscopic ellipsometry has been applied to characterize the optical constants of bulk Cu(In_0.7Ga_0.3)₅Se₈ and Cu(In_0.4Ga_0.6)₅Se₈ crystals grown by the Bridgman method. The spectra were measured at room temperature over the energy range 0.8-4.4 eV. Adachi’s model was used to calculate the dielectric functions as well as the spectral dependence of complex refractive index, absorption coefficient, and normal-incidence reflectivity. The calculated data are in good agreement with the experimental ones over the entire range of photon energies. The parameters such as strength, threshold energy, and broadening, corresponding to the E₀, E_1A, and E_1B interband transitions, have been determined using the simulated annealing algorithm.     

IR operated novel Ag0.98Cu0.02GaGe3Se8 single crystals

In this work, we report on the structural and optical properties of novel Ag_0.98Cu_0.02GaGe₃Se₈ single crystals that were synthesized by the Bridgman–Stockbarger technique. We have performed illumination by 10.6 μm CO₂ pulsed laser working in the microsecond time duration regime. Such illumination allows causing substantial changes for both pure electronic nonlinear optical effects like optical second harmonic generation as well as piezooptical effects described by the fourth rank tensors. The measurements of the piezo-optical effects were carried out at different temperatures. The effects are observed only during the IR CO₂ laser illumination and are disappeared after switching off the illumination. Simultaneously the IR induced optical second harmonic generation at Er:glass laser fundamental wavelength 1540 nm was performed during illumination by nanosecond Nd:YAG and Er³⁺:glass laser. The observed effects allow to use the studied materials as promising for IR-optoelectronic devices.     

Effect of sintering temperature on structure and nonlinear dielectric properties of Ba0.6Sr0.4TiO3 ceramics prepared by the citrate method

Ba_0.6Sr_0.4TiO₃ ceramics were prepared by a citrate precursor method. The structure and nonlinear dielectric properties of the resulting ceramics were investigated within the sintering temperature range 1200-1300 °C. Adopting fine Ba_0.6Sr_0.4TiO₃ powder derived from the citrate method was confirmed to be effective in reducing the sintering temperatures required for densification. The ceramic specimens sintered at 1230-1280 °C presented relative densities of around 95%. A significant influence of sintering temperature on the microstructure and nonlinear dielectric properties was detected. The discrepancy in nonlinear dielectric behavior among the specimens sintered at different temperatures was qualitatively interpreted in terms of the dielectric response of polar micro-regions under bias electric field. The specimens sintered at 1230 and 1250 °C attained superior nonlinear dielectric properties, showing relatively low dielectric losses (tan δ) of 0.24% and 0.22% at 10 kHz together with comparatively large figure of merits (FOM) of 121 and 142 at 10 kHz and 20 kV/cm, respectively.     

Electronic structure of a thermoelectric material: CsBi4Te6

We have calculated the electronic structure of CsBi₄Te₆ by means of first-principles self-consistent total-energy calculations within the local-density approximation using the full-potential linear-muffin-tin-orbital method. From our calculated electronic structure we have calculated the frequency dependent dielectric function. Our calculations shows that CsBi₄Te₆ a semiconductor with a band gap of 0.3 eV. The calculated dielectric function is very anisotropic. Our calculated density of state support the recent experiment of Chung et al. [Science 287 (2000) 1024] that CsBi₄Te₆ is a high performance thermoelectric material for low temperature applications.     

Elaboration and characterization of TiO2 nanoparticles incorporated in SiO2 host matrix

Nanometer-scale TiO₂ particles have been synthesized by sol-gel method. It was incorporated in a glass-based silica aerogel. The composite was characterized by various techniques such as particle size analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), transmission electron microscopy (TEM), X-ray diffraction (XRD), infrared spectroscopy (IR) and photoluminescence (PL). The bulk glass presents a strong luminescence at wavelengths ranging from 750 to 950 nm. This PL was attributed to various non-bridging oxygen hole centers (NBOHCs) defects resulting from thermal treatment and crystallization of TiO₂ at the interface between titania nanoparticles and silica host matrix.     

Third-order nonlinear optical properties of Bi2S3 and Sb2S3 nanorods studied by the Z-scan technique

Bismuth sulfide (Bi₂S₃) and antimony sulfide (Sb₂S₃) nanorods were synthesized by hydrothermal method. The products were characterized by UV-vis spectrophotometer, X-ray powder diffraction (XRD) and transmission electron microscope (TEM). Bi₂S₃ and Sb₂S₃ nanorods were measured by Z-scan technique to investigate the third-order nonlinear optical (NLO) properties. The result of NLO measurements shows that the Bi₂S₃ and Sb₂S₃ nanorods have the behaviors of the third-order NLO properties of both NLO absorption and NLO refraction with self-focusing effects. The third-order NLO coefficient χ⁽³⁾ of the Bi₂S₃ and Sb₂S₃ nanorods are 6.25×10⁻¹¹ esu and 4.55×10⁻¹¹ esu, respectively. The Sb₂S₃ and Bi₂S₃ nanorods with large third-order NLO coefficient are promising materials for applications in optical devices.     

Effect of hydroxyl groups on Er doped Bi2O3-B2O3-SiO2 glasses

A series of Er³⁺-doped Bi₂O₃-B₂O₃-SiO₂-Na₂O glasses with different hydroxyl groups were prepared and the interaction between the Er³⁺ ions and OH groups was investigated. Infrared spectra were measured in order to calculate the exact content of OH groups in samples. The observed increase of the fluorescence lifetime with the oxygen bubbling time has been related to the reduction in the OH content concentration evidenced by infrared (IR) absorption spectra, which confirmed that the OH groups were dominant quenching centers of excited Er³⁺ and a cause of concentration quenching of 1.5 μm band emission. Various nonradiative decay rates from ⁴I_13/2 of Er³⁺ with the change of OH content were determined from the fluorescence lifetimes and radiative decay rates, which were calculated on the basis of Judd-Ofelt theory.     

Orientation-dependent dielectric properties of Ba(Sn0.15Ti0.85)O3 thin films prepared by sol-gel method

The orientation-dependent dielectric properties of barium stannate titanate (Ba(Sn_0.15Ti_0.85)O₃, BTS) thin films grown on (1 0 0) LaAlO₃ single-crystal substrates through sol-gel process were investigated. The nonlinear dielectric properties of the BTS films were measured using an inter-digital capacitor (IDC). The results show that the in-plane dielectric properties of BTS films exhibited a strong sensitivity to orientation. The upward shift of Curie temperature (T_c) of the highly (1 0 0)-oriented BTS thin films is believed to be attributing to a tensile stress along the in-plane direction inside the film. A high tunability of 47.03% was obtained for the highly (1 0 0)-oriented BTS films, which is about three times larger than that of the BTS films with random orientation, measured at a frequency of 1 MHz and an applied electric field of 80 kV/cm. This work clearly reveals the highly promising potential of BTS films for application in tunable microwave devices.     

Optical studies of (NH4)2SO4 single crystal in the paraelectric phase

Transmittance and absorbance spectra of (NH₄)₂SO₄ single crystals along [010] direction were measured at different temperatures (296, 308, 318, 328 and 348 K) in the paraelectric phase. The absorption coefficient was computed and the analysis of the data revealed the existence of two optical transitions in (NH₄)₂SO₄ single crystals. The direct and indirect band gaps were shifted towards the longer wavelength with increasing temperature. The data on the allowed indirect transition was analyzed and interpreted in terms of two valence bands originated by spin orbit interaction and crystal field splitting. The momenta E_p were calculated as the difference between E_g1, the first valence to conduction band, and E_g2 for the second valence band at different temperatures. The results of extinction coefficient (k), the refractive index (n), and dielectric constants (ε) were also discussed and calculated as a function of wave length (λ). The heat treatment of the crystals proved that the variations of these optical parameters can be consequence of the internal microstructure changes caused by annealing.     

Optical absorption spectrum of Cu2O-CaO-P2O5 glasses

Homogeneous CaO-P₂O₅ and Cu₂O-CaO-P₂O₅ glasses were prepared using a melt-quenched method under controlled conditions. The binary glasses were found to be colourless and transparent while the ternary glasses changed from light green to dark green as the Cu₂O content increased. From the absorption edge studies, the values of the optical band gap, E_opt and Urbach energy, ΔE were evaluated. The position of the absorption edge and hence the optical band gap were found to depend on the glass composition. Analysis of the optical band gap shows that for the binary glasses, the value increases as the content of CaO decreases, while for the ternary glasses, the value of the optical band gap increases as the content of the Cu₂O decreases. The density of the glasses was also measured and was found to increase with the increase in CaO and Cu₂O contents.     

Microstructural, dielectric and spectroscopic properties of Li2O-Nb2O5-ZrO2-SiO2 glass system crystallized with V2O5

Li₂O-Nb₂O₅-ZrO₂-SiO₂ glasses mixed with different concentrations of V₂O₅ were crystallized. The samples were characterized by XRD, SEM and DTA techniques. The SEM pictures indicated that the samples contain well defined and randomly distributed crystal grains. The X-ray diffraction studies have revealed the presence of several crystalline phases in these samples. Optical absorption, ESR and photoluminescence spectral studies on these samples have indicated that a considerable proportion of vanadium ions do exist in V⁴⁺ state in addition to V⁵⁺ state and the redox ratio seems to be increasing with increase in the concentration of crystallizing agent V₂O₅. The infrared spectral studies have pointed out the existence of conventional SiO₄, ZrO₄, NbO₆, VO structural units in the glass ceramic network. The study of dielectric properties suggested a decrease in the insulating character of the glass ceramics with increase in the crystallizing agent. A.C. conductivity in the high temperature region seems to be connected mainly with the polarons involved in the process of transfer from V⁴⁺↔V⁵⁺ ions.     

Exciton spectra, valence band splitting, and energy band structure of CuGaXIn1−XS2 and CuGaXIn1−XSe2 crystals

Exciton spectra are studied in CuGa_XIn_1−XS₂ solid solutions by means of photoreflectivity and wavelength modulation spectroscopy at liquid nitrogen temperature. The exciton parameters, dielectric constants, and free carrier effective masses are deduced from experimental spectra by calculations in the framework of a model taking into account the spatial dispersion and the presence of a dead-layer. The crystal field and spin orbit valence band splitting is calculated as a function of X taking into account the energy position of excitonic lines. The energy band structure of CuGa_XIn_1−XS₂ and CuGa_XIn_1−XSe₂ compounds is derived from optical spectra at photon energies higher than the fundamental band gap. The energies of optical transitions are tabulated for X values from 0 to 1.     

Structural and optical properties of chemically synthesized monodispersed CdCr2S4 films

Alkaline chemical synthesis of amorphous CdCr₂S₄ (CCS) thin films of different thicknesses using cadmium chloride, chromic acid, disodium salt of ethylenediaminetetra acetic acid and thiourea precursors is reported, and the structural and surface morphological properties of CCS using X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and transmission electron microscopy (TEM) techniques are discussed. Films of aggregated grains with some void spaces are obtained. Change in band gap energy and electrical resistivity of CCS films are discussed as a function of film thickness. n-type conductivity is confirmed from the sign of thermally generated voltage across the cold and hot junctions.     

Effect of preferred orientation on magnetoelectric properties of multiferroic La0.7Sr0.3MnO3/BaTiO3 heterostructure

The epitaxial La_0.7Sr_0.3MnO₃/BaTiO₃ bilayer heterostructures were deposited on LaAlO₃ (001) and (110) substrates by pulsed laser deposition. The inherent ferromagnetic, ferroelectric properties and strong magnetoelectric (ME) effect at room temperature were approved, which correlated to the preferred orientation of the films. Both heterostructures showed similar frequency-dependent ME behavior in 0.1 kHz-100 kHz, the ME voltage coefficients were around 140 mV/cm Oe and 104.8 mV/cm Oe at 1 kHz for (001) and (110) oriented bilayers, respectively. This was at least one order of magnitude higher than previously reported results of the related heterostructures, which is mainly ascribed to the lower dielectric constant of BTO film.     

Chiral optical absorption bands in [ ]Cd1−x Mnx Ga2S4 semiconducting compound

[ ]Cd_1−x Mn_x Ga₂S₄ is a semimagnetic semiconductor and it has revealed an exceptional property namely ‘optical activity‘. Therefore, a spectroscopic investigation of chiral absorption bands has been carried out with the view to examine the role of d*-d states of manganese atoms. It has been found that inner transitions of Mn⁺⁺ dominate the spectral region with a special feature, indicating that these transitions show the presence of a substantial contribution from the magnetic dipole moment which rotates the electric vector of the incident polarized radiation. The origin is associated to the lack of a symmetry center caused by the ordered vacancies in this defect compound.     

Dielectric and AC conductivity behavior of BaBi2Nb2O9 ceramics

The complex dielectric and AC conductivity response of BaBi₂Nb₂O₉ relaxor ferroelectric ceramics were studied as a function of frequency (100 Hz-10 MHz) at various temperatures. The observed dielectric behavior was characterized by two types of relaxation processes which were described by the ‘universal relaxation law’. The frequency dependence of conductivity which showed a classical relaxor behavior followed the Jonscher's universal law σ(ω)=σ₀+Aωⁿ. The exponent n exhibited a minimum in the vicinity of temperatures of dielectric anomaly while the pre-factor A showed a maximum. The temperature dependence of n followed the Vogel-Fulcher relation with activation energy of about 0.14 eV.     

Preparation and characterization of Cd2Nb2O7 thin films on Si substrates

Thin Cd₂Nb₂O₇ films were grown on single-crystal p-type SiO₂/Si substrates by the metallo-organic decomposition (MOD) technique. The films were investigated by X-ray diffraction, X-ray energy-dispersive spectroscopy, and field emission scanning electron microscopy, and showed a single phase (cubic pyrochlore), a crack-free spherical grain structure, and nanoparticles with a mean size of about 68 nm. A Cauchy model was also used in order to obtain the thickness and index of refraction of the stack layers (transparent layer/SiO₂/Si) by spectroscopic ellipsometry (SE). The dielectric constant (K) of the films was calculated to be about 25 from the capacitance-voltage (C-V) measurements.     

Preparation of Cu2ZnSnS4 thin films by hybrid sputtering

In order to fabricate Cu₂ZnSnS₄ thin films, hybrid sputtering system with two sputter sources and two effusion cells is used. The Cu₂ZnSnS₄ films are fabricated by the sequential deposition of metal elements and annealing in S flux, varying the substrate temperature. The Cu₂ZnSnS₄ films with stoichiometric composition are obtained at the substrate temperature up to 400 °C, whereas the film composition becomes quite Zn-pool at the substrate temperature above 450 °C. The Cu₂ZnSnS₄ film shows p-type conductivity, and the optical absorption coefficient and the band gap of the Cu₂ZnSnS₄ film prepared in this experiment are suitable for fabricating a thin film solar cell.     

The influence of different fabrication processes on characteristics of excess Bi2O3-doped 0.95 (Na0.5Bi0.5)TiO3–0.05 BaTiO3 ceramics

In this study, we will develop the influences of the excess x wt% (x=0, 1, 2, and 3) Bi₂O₃-doped and the different fabricating process on the sintering and dielectric characteristics of 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃ ferroelectric ceramics with the aid of SEM and X-ray diffraction patterns, and dielectric–temperature curves. The 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ ceramics are fabricated by two different processes. The first process is that (Na_0.5Bi_0.5)TiO₃ composition is calcined at 850 °C and BaTiO₃ composition is calcined at 1100 °C, then the calcined (Na_0.5Bi_0.5)TiO₃ and BaTiO₃ powders are mixed in according to 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions. The second process is that the raw materials are mixed in accordance to the 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions and then calcining at 900 °C. The sintering process is carried out in air for 2 h from 1120 to 1240 °C. After sintering, the effects of process parameters on the dielectric characteristics will be developed by the dielectric–temperature curves. Dielectric–temperature properties are also investigated at the temperatures of 30–350 °C and at the frequencies of 10 kHz–1 MHz.