Synthesis and characterization of Sr3Al2O6：Eu2＋, Dy3＋ phosphors prepared by sol-gel-combustion processing

A type of red luminescent Sr3Al2O6:Eu2+, Dy3+ phosphor powder is synthesised by sol-gel-combustion processing, with metal nitrates used as the source of metal ions and citric acid as a chelating agent of metal ions. By tracing the formation process of the sol-gel, it is found that it is necessary to reduce the amount of NO3- by dropping ethanol into the solution for forming a stable and homogeneous sol-gel. Thermogravimetric and Differential Scanning Calorimeter Analysis, x-ray diffractionmeter, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the luminescent properties of the as-synthesised Sr3Al2O6:Eu2+, Dy3+. The results reveal that the Sr3Al2O6 crystallises completely when the combustion ash is sintered at 1250 C. The excitation and the emission spectra indicate that the excitation broadband lies mainly in a visible range and the phosphors emit a strong light at 618 nm under the excitation of 472 nm. The afterglow of (Sr0.94Eu0.03Dy0.03)3Al2O6 phosphors sintered at 1250 ℃ lasts for over 1000 s when the excited source is cut off.     

Energy transfer between activators at different crystallographic sites in Sr3SiO5:Eu

A yellow phosphor, Sr₃SiO₅:Eu²⁺, was synthesized by a high temperature solid-state method. Sr₃SiO₅:Eu²⁺ exhibits a single yellow emission under the blue radiation excitation. However, Sr₃SiO₅:Eu²⁺ shows a two-peak emission under the ultraviolet radiation excitation when Eu²⁺ doping content is less than 0.01 mol. Moreover, the blue emission disappears and the yellow emission reaches the peak value when Eu²⁺ doping content is 0.01 mol. Namely, the energy transfer takes place between the Eu²⁺ activators, which is located at two different crystallographic sites in the Sr₃SiO₅. And the energy transfer mechanism is the dipole-dipole interaction.     

Dy含量对红色长余辉发光材料Sr3Al2Ｏ6:Eu2＋,Dy3＋性能的影响

采用溶胶凝胶法制备了Sr₃Al₂Ｏ₆:Eu^2＋,Dy^3＋红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr₃Al₂Ｏ₆,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr₃Al₂Ｏ关键词： 红色长余辉 3Al₂Ｏ₆')" href="#">Sr₃Al₂Ｏ₆ 溶胶凝胶法     

Acetate reduction synthesis of Sr2Si5N8:Eu phosphor and its luminescence properties

A novel synthesis method was developed for the efficient red phosphor, Eu²⁺-activated Sr₂Si₅N₈, by employing the strontium acetate as both the reducing agent and strontium source. The phase purity of final product was strongly dependent on the heating rate of the precursors. Sr₂Si₅N₈:Eu²⁺ (2 at%) phosphor presented a broadband excitation spectrum in the range 300–500 nm, matching well with the blue emission (400/460 nm) of current InGaN light-emitting diodes (LEDs). The red emission peaking at 619 nm gave the relatively high (about 155%) intensity compared with the Y₃Al₅O₁₂ (YAG) (P46-Y3) standard phosphor. In addition, the saturated chromatic coordinates (0.638, 0.359) allowed it a promising candidate as a red phosphor in white LEDs application for illumination or display.     

Effects of dopant concentrations on phosphorescence properties of Eu/Dy-doped Sr3MgSi2O8

Long afterglow Sr₃MgSi₂O₈: Eu, Dy phosphor with high brightness was prepared by sintering at high temperature and weak reductive atmosphere. The luminescent properties of this photoluminescent pigment were studied systematically by investigating concentration effects. The analytical results indicated that the main emission peaks appear at 482 nm. The excitation and emission spectra of this phosphor show that both of them are broadband. This is ascribed to the 4f⁷→4f⁶5d¹ transition of Eu²⁺ in the pigment matrix, which is in good agreement with the calculated value of 470 nm, and implies that luminescent centers Eu²⁺ occupy the deca-coordinated Sr²⁺ sites with the host of Sr₃MgSi₂O₈.     

Combustion synthesis and luminescence properties of NaY1−xEux(WO4)2 phosphors

The red phosphors NaY_1−xEu_x(WO₄)₂ with different concentrations of Eu³⁺ were synthesized via the combustion synthesis method. As a comparison, NaEu(WO₄)₂ was prepared by the solid-state reaction method. The phase composition and optical properties of as-synthesized samples were studied by X-ray powder diffraction and photoluminescence spectra. The results show that the red light emission intensity of the combustion synthesized samples under 394 nm excitation increases with increase in Eu³⁺ concentrations and calcination temperatures. Without Y ions doping, the emission spectra intensity of the NaEu(WO₄)₂ phosphor prepared by the combustion method fired at 900 °C is higher than that prepared by the solid-state reaction at 1100 °C. NaEu(WO₄)₂ phosphor synthesized by the combustion method at 1100 °C exhibits the strongest red emission under 394 nm excitation and appropriate CIE chromaticity coordinates (x=0.64, y=0.33) close to the NTSC standard value. Thus, its excellent luminescence properties make it a promising phosphor for near UV InGaN chip-based red-emitting LED application.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Effect of boric acid on structure,morphology and luminescent properties of divalent europium doped calcium aluminate phosphors

Blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ were prepared by high temperature solid-state method. Their structure, morphology and luminescent properties were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM) and fluorescence spectroscopy. The effect of different amounts of fluxing agent H₃BO₃ on structure, morphology and luminescent properties of blue phosphors Ca_1 − xAl₂O₄: xEu²⁺ luminous intensity caused by different amount of H₃BO₃ was also investigated. The amount of H₃BO₃ doped Ca_1 − xAl₂O₄: xEu²⁺ in optimal luminous intensity had been determined. The results showed that both the excitation and emission spectra of samples were all broad bands, and that the peak of emission spectra was near 442 nm, which was corresponding to the 4f⁶5d → 4f⁷ transition of Eu²⁺ illuminating blue light. Ca_1 − xAl₂O₄: xEu²⁺ (x = 3.5 mol%) could be gained with good morphology and the best luminous intensity when H₃BO₃ mass ratio was 0.5 wt%.     

A red oxide phosphor, Sr2ScAlO5:Eu2+ with perovskite-type structure, for white light-emitting diodes

Sr2ScAlO5:Eu2+,a red oxide phosphor with a perovskite-type structure,has been synthesized through a solid-state reaction and its luminescence properties have been investigated.An absorption band centering at 450 nm is observed from the diffuse reflection spectra and the excitation spectra,indicating that the phosphor can match perfectly with the blue light of InGaN light-emitting diodes.A broad red emission band at 620 nm is found from the emission spectra,originating from the 4f 6 5d-4f 7 transition of the Eu 2+ ions.The best doping content of Eu in this material is about 5%.Sr2ScAlO5:Eu2+is a highly promising red phosphor for use in white light-emitting diodes.     

Temperature-dependence of the structural and afterglow luminance properties of polymer/SrAlxOy:Eu,Dy composites

Although aluminate phosphors have attracted great interest for applications in lamps, cathode ray tubes and plasma display panels, there still remain issues affecting operational parameters such as luminescence efficiency, stability against temperature, high color purity and perfect decay time. In addition, issues involving important aspects of the monoclinic↔hexagonal phase transition temperature still exist. In this work, SrAl_xO_y:Eu²⁺,Dy³⁺ phosphor powders were prepared by the sol–gel method. X-ray diffraction (XRD) has shown that both crystallinity and crystallite sizes increased as the temperature increased. Both SrAl₂O₄ and Sr₂Al₃O₆ phases were observed. Photoluminescence (PL) characterization shows temperature-dependence, which indicates emission at low and high annealing temperatures originating from Eu²⁺ and Eu³⁺ ions. Thermoluminescence glow and decay measurements provided useful insight on the influence of traps on luminescence behavior. Differential scanning calorimetry (DSC) and thermogravimetric studies (TGA) on composites of the phosphor in low density polyethylene (LDPE) demonstrated the varied influence of annealing temperature on some luminescence and thermal properties.     

Synthesis of Gd2Ti2O7:Eu, V phosphors by sol-gel process and its luminescent properties

A red-emitting phosphor material, Gd₂Ti₂O₇:Eu³⁺, V⁴⁺, by added vanadium ions is synthesized using the sol-gel method. Phosphor characterization by high-resolution transmission electron microscopy shows that the phosphor possesses a good crystalline structure, while scanning electron microscopy reveals a uniform phosphor particle size in the range of 230-270 nm. X-ray photon electron spectrum analysis demonstrates that the V⁴⁺ ion promotes an electron dipole transition of Gd₂Ti₂O₇:Eu³⁺ phosphors, causing a new red-emitting phenomenon, and CIE value shifts to x=0.63, y=0.34 (a purer red region) from x=0.57, y=0.33 (CIE of Gd₂Ti₂O₇:Eu³⁺). The optimal composition of the novel red-emitting phosphor is about 26% of V⁴⁺ ions while the material is calcinated at 800  °C. The results of electroluminescent property of the material by field emission experiment by CNT-contained cathode agreed well with that of photoluminescent analysis.     

Photoluminescence properties of Sr1-xSi2O2N2: Eux as green to yellow-emitting phosphor for blue pumped white LEDs

This study evaluated potential applications of green to yellow-emitting phosphors (Sr_1−xSi₂O₂N₂: Eu²⁺_x) in blue pumped white light emitting diodes. Sr_1-xSi₂O₂N₂: Eu²⁺_x was synthesized at different Eu²⁺ doping concentrations at 1450 °C for 5 h under a reducing nitrogen atmosphere containing 5% H₂ using a conventional solid reaction method. The X-ray diffraction patterns of the prepared phosphor (Sr_1-xSi₂O₂N₂: Eu²⁺_x) were indexed to the SrSi₂O₂N₂ phase and an unknown intermediate phase. The photoluminescence properties of these phosphors (Sr_1−xSi₂O₂N₂: Eu²⁺_x) showed that the samples were excited from the UV to visible region due to the strong crystal field splitting of the Eu²⁺ ion. The emission spectra under excitation of 450 nm showed a bright color at 545-561 nm. The emission intensity increased gradually with increasing Eu²⁺ doping concentration ratio from 0.05 to 0.15. However, the emission intensity decreased suddenly when the Eu²⁺ concentration ratio was >0.2. As the doping concentration of Eu²⁺ was increased, there was a red shift in the continuous emission peak. These results suggest that Sr_1-xSi₂O₂N₂: Eu₂⁺_x phosphor can be used in blue-pumped white light emitting diodes.     

Orange emission enhancement by energy transfer in Sr3Al2O5Cl2:Ce, Eu phosphor for solid-state lighting

Orange-emissive Ce³⁺/Eu²⁺ co-doped Sr₃Al₂O₅Cl₂ phosphors were synthesized by a solid-state reaction. The large overlap between the emission spectrum of blue Sr₃Al₂O₅Cl₂:Ce³⁺ and the excitation spectrum of orange Sr₃Al₂O₅Cl₂:Eu²⁺, and the shortening trend in lifetime of Ce³⁺ donors with increasing Eu²⁺ concentration in Sr₃Al₂O₅Cl₂:Ce³⁺, Eu²⁺ provide the strong evidence of energy transfer from Ce³⁺ to Eu²⁺ ions. It supports that the orange emission intensity of the optimal co-doped phosphor is 1.5 times stronger than that of single Eu²⁺-doped one. The Sr₃Al₂O₅Cl₂:Ce³⁺, Eu²⁺ phosphor is a promising orange-emitting phosphor for warm-white-light-emitting diode because of its effective excitation in the near ultraviolet range.     

Luminescence characteristics of Eu3+ activated borate phosphor for white light emitting diode

In this paper, the Sr₃Y₂ (BO₃)₄:Eu³⁺ phosphor was synthesized by high temperature solid-state reaction method and the luminescence characteristics were investigated. The emission spectrum exhibits one strong red emission at 613nm corresponding to the electric dipole ⁵D₀--⁷F₂ transition of Eu³⁺ under 365nm excitation, this is because Eu³⁺ substituted for Y³⁺ occupied the non-centrosymmetric position in the crystal structure of Sr₃Y₂ (BO₃)₄. The excitation spectrum indicates that the phosphor can be effectively excited by ultraviolet (254nm, 365nm and 400nm) and blue (470nm) light. The effect of Eu³⁺ concentration on the red emission of Sr₃Y₂ (BO₃)₄:Eu³⁺ was measured, the result shows that the emission intensities increase with increasing Eu³⁺ concentration, then decrease. The Commission Internationale del'Eclairage chromaticity (x, y) of Sr₃Y₂(BO₃)₄:Eu³⁺ phosphor is (0.640,0.355) at 15 mol% Eu³⁺.     

Novel blue-emitting phosphor Sr2.979Eu0.021Al10−xBxSiO20 (x=0, 0.25, 0.5, 0.75 and 1) for PDP applications

A series of blue-emitting phosphor Sr_3−xEu_xAl₁₀SiO₂₀ (x=0-0.025, insteps of 0.0025) have been synthesized and the emission intensity is found to be maximum for x=0.02. The effect of boron substitution in the Al site in Sr₃Al₁₀SiO₂₀:Eu²⁺ phosphor has been investigated to improve the blue emission of Eu²⁺. A series of boron-substituted compositions have been made Sr_2.979Eu_0.021Al_10−xB_xSiO₂₀ (x=0, 0.25, 0.5, 0.75 and 1) and studied their photoluminescence (PL) property under UV and VUV excitation. The X-ray diffraction patterns of Sr_2.979Eu_0.021Al_10−xB_xSiO₂₀ (x=0, 0.25, 0.5, 0.75 and 1) show single phase formation and all the compositions crystallize in monoclinic structure with space group C2/m. Blue emission (due to Eu²⁺ ion) has been found in all compositions and the emission intensity is found to be maximum for x=0.25 and it is ∼2 times higher than that of x=0 composition (PL intensity 62% vs. commercial BAM). Hence, this phosphor could be possible potential candidate for blue light-emitting phosphor for plasma display panel (PDP) applications.     

A white light emitting phosphor Sr1.5Ca0.5SiO4:Eu, Tb, Eu for LED-based near-UV chip: Preparation, characterization and luminescent mechanism

In this work, we report preparation, characterization and luminescent mechanism of a phosphor Sr_1.5Ca_0.5SiO₄:Eu³⁺,Tb³⁺,Eu²⁺ (SCS:ETE) for white-light emitting diode (W-LED)-based near-UV chip. Co-doped rare earth cations Eu³⁺, Tb³⁺ and Eu²⁺ as aggregated luminescent centers within the orthosilicate host in a controlled manner resulted in the white-light phosphors with tunable emission properties. Under the excitation of near-UV light (394 nm), the emission spectra of these phosphors exhibited three emission bands: one broad band in the blue area, a second band with sharp lines peaked in green (about 548 nm) and the third band in the orange-red region (588-720 nm). These bands originated from Eu²⁺ 5d→4f, Tb³⁺⁵D₄→⁷F_J and Eu³⁺⁵D₀→⁷F_J transitions, respectively, with comparable intensities, which in return resulted in white light emission. With anincrease of Tb³⁺ content, both broad Eu²⁺ emission and sharp Eu³⁺ emission increase. The former may be understood by the reduction mechanism due to the charge transfer process from Eu³⁺ to Tb³⁺, whereas the latter is attributed to the energy transfer process from Eu²⁺ to Tb³⁺. Tunable white-light emission resulted from the system of SCS:ETE as a result of the competition between these two processes when the Tb³⁺ concentration varies. It was found that the nominal composition Sr_1.5Ca_0.5SiO₄:1.0%Eu³⁺, 0.07%Tb³⁺ is the optimal composition for single-phased white-light phosphor. The CIE chromaticity calculation demonstrated its potential as white LED-based near-UV chip.     

Luminescent properties of Eu-activated Sr3B2SiO8: A red-emitting phosphor for white light-emitting diodes

Single-phased Sr₃B₂SiO₈:Eu³⁺ phosphor was prepared by a solid-state method at 1020 °C. The luminescence spectra showed that Sr₃B₂SiO₈:Eu³⁺ phosphor can be effectively excited by near ultraviolet light (393 nm) and blue light (464 nm). When excited at 393 or 464 nm Sr₃B₂SiO₈:Eu³⁺ exhibited the main emission peaks at 611 and 620 nm, which resulted from the supersensitive ⁵D₀→⁷F₂ transition of Eu³⁺. The luminescence intensity of Sr₃B₂SiO₈:Eu³⁺ at 611 and 620 nm reached the maximum when the doping content of Eu³⁺ was 4.5 mol%. Its chromaticity coordinates (0.646, 0.354) were very close to the NTSC standard values (0.67, 0.33). Thus, Sr₃B₂SiO₈:Eu³⁺ is considered to be an efficient red-emitting phosphor for long-UV InGaN-based light-emitting diodes.     

Photoluminescence in MgxSr1−xAl2O4:Eu, Ndand electron-vibrational interaction in the Eu 5d states

Green phosphor compositions Mg_xSr_1−xAl₂O₄:Eu, Nd (with x=0.05-0.25) were prepared by solid state reaction method. The effect of Mg substitution on photoluminescence characteristics was investigated. The photoluminescence show intense green emission for MgSrAl₂O₄:Eu²⁺, Nd³⁺ with long persistence. This green emission corresponds to transitions from 4f⁶5d¹ to 4f⁷ of Eu²⁺ ion. Comparative analysis of the excitation and emission spectra were used to evaluate the crystal field splitting of the 5d states of Eu²⁺ and the parameters of electron-vibrational interaction, such as Huang-Rhys factor, effective phonon energy, and zero-phonon line position.     

The structure and luminescence properties of long afterglow phosphor Y3−xMnxAl5−xSixO12

A series of phosphors with the composition Y_3−xMn_xAl_5−xSi_xO₁₂ (x=0, 0.025, 0.050, 0.075, 0.150, 0.225, 0.300) were prepared with solid state reactions. The X-ray powder diffraction analysis of samples shows that the substitution of Mn²⁺ and Si⁴⁺ does not change the garnet structure of phosphors, but makes the interplanar distance decrease to a certain extent. The emission spectra show that Mn²⁺ in Y₃Al₅O₁₂ emits yellow-orange light in a broad band. With the increment of substitution content, the emission intensity of the phosphors increases firstly then decreases subsequently, and the emission peak moves to longer wavelength. Afterglow spectra and decay curves show that all the Mn²⁺ and Si⁴⁺ co-doped samples emit yellow-orange light with long afterglow after the irradiation of ultraviolet light. The longest afterglow time is 18 min. Thermoluminescence measurement shows that there exist two kinds of traps with different depth of energy level and their depth decreases with the increment of substitution content.     

The structure and luminescence properties of a novel orange emitting phosphor Y3MnxAl5−2xSixO12

A series of phosphors with the composition Y₃Mn_xAl_5−2xSi_xO₁₂ (x=0, 0.05, 0.1, 0.15, 0.2, 0.3, 0.4, 0.5, 0.6) was prepared through solid state reactions. X-ray powder diffraction analysis of samples shows that when co-doping content does not exceed 16% of Al³⁺, equimolar co-doping of Mn²⁺ and Si⁴⁺ does not change the garnet structure of phosphors, but makes the interplanar distance to decrease a certain extent. However, if the co-doping content exceeds 16%, new phases will form in the samples. The excitation and emission spectra of samples show that Mn²⁺ in Y₃Mn_xAl_5−2xSi_xO₁₂ emits broadband orange light (peak wavelength varies from 586 to 593 nm). With an increment in co-doping content, the emission intensity of the phosphors increases when the value of x is lower than 0.1 while it decreases when it is higher than 0.1 and the emission peak moves to a longer wavelength.