含纳米晶颗粒的Yb3+/Er3+共掺透明碲酸盐玻璃陶瓷的光谱性质研究

在组成为15Li2O-15Nb2O5-70TeO2-0.1Er2O3-0.4Yb2O3（%, 摩尔分数）的碲酸盐玻璃基础上, 采用两步热处理法制备了透明的含纳米晶颗粒碲酸盐玻璃陶瓷. 通过X射线衍射（XRD）测试表明, 玻璃陶瓷中的晶体颗粒组成为Yb6Te5O19.2或Er6Te5O19.2, 晶粒尺寸约为55 nm. 根据Judd-Ofelt理论计算了Er^3＋离子在基质玻璃和玻璃陶瓷中的光谱参数Ωt（t＝2, 4, 6）以及Er^3＋：4I15/2→4I13/2跃迁自发辐射几率, 根据McCumber理论计算了Er^3＋：4I13/2→4I15/2跃迁的发射截面. 测试了基质玻璃和玻璃陶瓷的拉曼光谱, 对比研究了铒离子在基质玻璃和玻璃陶瓷中1.5 μm处荧光和上转换光谱特性.     

Er~(3+)-Yb~(3+)双掺Li_2O-ZnO-SiO_2系透明玻璃陶瓷的制备及表征

采用熔融-晶化技术合成了Er3+-Yb3+掺杂的Li2O-ZnO-SiO2系(LZS)透明玻璃陶瓷。利用DTA,XRD,SEM,UV-Vis-NIR等对样品进行了表征,并分析了影响玻璃陶瓷析晶的因素。结果表明,LZS系玻璃具有良好的结晶性能,其最佳热处理温度为700℃,最佳热处理时间为50min,其主晶相为石英和Li8Zn10Si7O28。该玻璃陶瓷在可见光区的透过率可达85%。经SEM分析,粒子直径为30~40nm。荧光光谱显示,玻璃陶瓷的发射光谱较之基质玻璃有了极大的提高,而且在1530nm附近获得一较强发射峰。     

Eu3+-Tb3+共掺杂SiO2-B2O3-Na2O-Y2O3-P2O5玻璃陶瓷的制备与发光性能

采用高温熔融法制备Eu3+?Tb3+共掺杂SiO2?B2O3?Na2O?Y2O3?P2O5前驱体玻璃。对前驱体玻璃粉末进行差示扫描量热(DSC)分析,确定玻璃陶瓷样品的热处理温度。前驱体玻璃热处理后,采用X射线衍射(XRD)和扫描电镜(SEM)分析可知前驱体玻璃中有Na3.6Y1.8(PO4)3晶粒析出。利用荧光光谱对玻璃陶瓷样品的发光性能进行表征,同时分析了Tb3+离子的荧光衰减曲线,确定Eu3+、Tb3+离子的发光机理以及能量传递过程。通过对Eu3+?Tb3+共掺杂玻璃陶瓷样品的发射光谱采集并用色坐标软件和色温计算程序,获得玻璃陶瓷样品的色坐标和相关色温。     

Er~(3+)-Yb~(3+)掺杂SiO_2-SrO-NaF玻璃陶瓷的制备及表征

采用熔融晶化法制备了主晶相为SrF_2的Er~(3+)-Yb~(3+)共掺透明氟氧化物玻璃陶瓷,利用DSC、XRD、SEM、UV-Vis-NIR和荧光光谱对样品的结构、形貌、发光性能进行了测试与表征。研究表明:该体系玻璃最佳热处理温度为620℃,最佳热处理时间为2h,并讨论了Yb~(3+)不同掺杂浓度对Er~(3+)-Yb~(3+)共掺玻璃陶瓷样品上转换发光性能的影响,确定Er~(3+)-Yb~(3+)最佳掺杂浓度比为1∶7,同时观察到了明亮的绿光(522,540 nm)和较弱的红光(656 nm),对Er~(3+)和Yb~(3+)之间的能量传递过程进行了讨论。     

掺钕氟氧化物玻璃陶瓷的制备及表征

采用熔融和晶化技术合成出含CaF2微晶的Nd3+离子掺杂透明氟氧化物玻璃陶瓷材料, 并通过DTA, XRD, FEG-ESEM和UV-Vis-Nir分光光度计和傅里叶变换荧光光谱仪等对样品进行了表征. 结果表明, 玻璃陶瓷主晶相为CaF2, 晶相粒径为15 nm; 可见光透过率为78%~87%, 近红外透过率为84%~93%; 由于Nd3+在热处理后优先富集在具有低声子能量的CaF2晶相中, 从而改变了配体场, 使荧光谱线在1060 nm处的峰值比原始玻璃强度大.     

Ho3+-Yb3+掺杂磷酸盐玻璃陶瓷的制备与发光性能

采用传统熔融法制备了Na_2O-Y_2O_3-P_2O_5-SiO_2前驱体玻璃,并对前驱体玻璃样品进行热处理,成功合成透明磷酸盐玻璃陶瓷。对玻璃陶瓷样品进行XRD分析确定玻璃基质中有Na_(3.6)Y_(1.8)(PO_4)_3晶体析出。讨论了热处理时间对玻璃陶瓷结晶度和晶粒尺寸的影响,确定热处理温度为655℃,热处理时间为2 h。比较Ho~(3+)单掺和Ho~(3+)-Yb~(3+)共掺玻璃陶瓷上转换发光强度,确定Ho~(3+)与Yb~(3+)的最佳掺杂物质的量之比为1∶2。同时讨论了Ho~(3+)-Yb~(3+)之间的能量转移。使用积分球测得样品的上转换发光量子效率。     

钕掺杂磷酸盐玻璃陶瓷的制备及表征

利用熔融和晶化技术制备掺钕磷酸盐玻璃陶瓷.采用差热分析、X射线衍射、扫描电子显微镜、紫外-可见-近红外分光光度计及荧光光谱仪对材料进行表征和分析.结果表明,在490～540 ℃核化1～2 h,在550 ℃晶化1～3 h,可制得主晶相为Al2SiO5的透明玻璃陶瓷.其透过率可达69%,晶粒平均尺寸为90 nm,并随热处理时间的增加逐渐增大,但透过率降低.由于Nd3+在热处理后进入到Al2SiO5晶相中,使荧光谱线在1 056 nm处峰值比原始玻璃强度大.     

钕掺杂磷酸盐微晶玻璃的制备及表征

利用熔融和晶化技术制备掺钕磷酸盐玻璃陶瓷。 采用差热分析、X射线衍射、扫描电子显微镜、紫外 可见 近红外分光光度计及荧光光谱仪对材料进行表征和分析。 结果表明,在490～540 ℃核化1～2 h,在550 ℃晶化1～3 h,可制得主晶相为Al2SiO5的透明玻璃陶瓷。 其透过率可达69%,晶粒平均尺寸为90 nm,并随热处理时间的增加逐渐增大,但透过率降低。 由于Nd3+在热处理后进入到Al2SiO5晶相中,使荧光谱线在1 056 nm处峰值比原始玻璃强度大。     

含氟CaO-P2O5-SiO2-Na2O-B2O3玻璃陶瓷的制备及性能表征

采用溶胶-凝胶法制备CaO-P₂O₅-SiO₂-Na₂O-B₂O₃体系前驱体粉末,用CaF₂替代部分CaO再次制备前驱体粉末。 通过TG-DSC分析确定结晶温度为865 ℃,经过热处理获得主晶相为Na₆Ca₃Si₆O₁₈的玻璃陶瓷。 通过X射线衍射(XRD)、傅里叶红外光谱(FTIR)、扫描电子显微镜(SEM)等技术手段及体外生物活性实验分析玻璃陶瓷的显微结构及性能。 结果表明,CaF₂的加入能提高玻璃陶瓷的体积密度、抗折强度和弹性模量,并且不会破坏玻璃陶瓷的生物活性。     

Er3+-Yb3+掺杂SiO2-SrO-NaF玻璃陶瓷的制备及表征

采用熔融晶化法制备了主晶相为SrF₂的Er³⁺-Yb³⁺共掺透明氟氧化物玻璃陶瓷,利用DSC、XRD、SEM、UV-Vis-NIR和荧光光谱对样品的结构、形貌、发光性能进行了测试与表征。研究表明：该体系玻璃最佳热处理温度为620℃,最佳热处理时间为2 h,并讨论了Yb³⁺不同掺杂浓度对Er³⁺-Yb³⁺共掺玻璃陶瓷样品上转换发光性能的影响,确定Er³⁺-Yb³⁺最佳掺杂浓度比为1：7,同时观察到了明亮的绿光（522,540 nm）和较弱的红光（656 nm）,对Er³⁺和Yb³⁺之间的能量传递过程进行了讨论。     

白光LED用黄色荧光粉Ba(Y1-0.5x-yAly)2S4:xHo3+的合成和发光特性

采用高温固相法合成了Ba(Y1-0.5x-yAly)2S4:xHo3+系列荧光粉。在465 nm蓝光激发下,荧光粉的发射光谱呈多谱带发射,主峰位于492、543和661 nm处,分别对应于Ho3+的5F3→5I8,(5S2,5F4)→5I8和5F5→5I8跃迁发射。研究了Ho3+和Al3+掺杂量对BaY2S4:Ho3+发光性能的影响。结果表明,随着Ho3+掺杂量的逐渐增大,荧光粉的发光颜色由绿色逐渐向红色转变;适量Al3+取代Y3+可以提高BaY2S4:Ho3+荧光粉的发光强度。荧光粉Ba(Y0.665Al0.3)2S4:0.07Ho3+在蓝光(465 nm)激发下发射黄光,是一种潜在的白光LED用黄色荧光粉。     

Spectroscopic properties of Ho3+ ions doped in tellurite glass

Spectroscopic properties of Ho3+ doped tellurite glass (1 mol.% of Ho3+) have been studied. The absorption and fluorescence spectra have been recorded and analysed using the Judd-Offelt theory. The analysis indicates that Ho doped tellurite glasses can show lasing on the 5F4 (5S2)-5I8 transition (548.0 nm).     

SrF_2晶体中Ho~(3 )-Ho~(3 )离子对的上转换发光研究

究了在连续可调谐红色染料激光激发下,掺杂Ｈｏ３＋离子的ＳｒＦ２单晶中Ｈｏ３＋Ｈｏ３＋对的上转换发光特性。Ｈｏ３＋Ｈｏ３＋离子对的上转换发光主要分布于：强５Ｆ３→５Ｉ８跃迁４８０ｎｍ蓝色发射,较强５Ｓ２,５Ｆ４→５Ｉ８跃迁的５４０ｎｍ绿色发射。给出了ＳｒＦ２晶体中Ｈｏ３＋离子发射光谱中不同能级跃迁的谱峰及所对应的跃迁。通过对样品的激发,发射光谱和发光的上升、衰减等过程的分析,研究了发光中心的结构,分析了Ｈｏ３＋上转换发光的机制,建立了Ｈｏ３＋Ｈｏ３＋离子对的能级图     

Upconversion Properties of LiNbO_3 Single Crystals Co-doped with Ho and Yb

The IR-to-visible upconversion fluorescent crystals, Yb:Ho:LiNbO3, with a constant Ho3+ concentration (0.1 mol%) and different doping concentrations of Yb3+ (0.5, 1.5, 2.0, 2.5, 3.0 mol%) are synthesized by Czochralski method in air atmosphere. X-ray diffraction shows that the obtained crystal is a single phase of LiNbO3 and the rare-earth ions occupied the Li+ or Nb5+ sites instead of the interstitial sites. Under 980 nm excitation, green and red emission bands due to the Ho3+ (5S2, 5F4)/5I8 and Ho3+ 5F5/5I8 energy transitions are observed in these samples, respectively. Power dependence studies on these samples with different Yb3+ dopant concentrations indicate that the red and green emissions are based on a two-photon process. The intensities of the red and green upconversion fluorescence increase with Yb3+ ions of 0~2.0 mol% because of an increased Yb3+ sensitization, but decrease at higher concentrations owing to the back-energy transfer between the Yb3+ and Ho3+ ions.     

Synthesis and Crystal Structure of Ho_4S_3Si_2O_7

1 INTRODUCTION Halide fluxes are excellent media for growing single crystals of chalcogenides[1~5]. On our research in the Ln-Cu-Zn-Se system to find new phases and to search for potential infrared ceramic materials, two new compounds, KHo2CuSe4 and KEr2CuSe4, were synthesized from the reaction of the precursor with KCl flux[6]. In an attempt to synthesize the homologous sulfide by the same method using KBr as flux in a sealed evacuated quartz tube, single crystals of Ho4S3Si2O7 w…     

Preparation of yttrium oxysulfide phosphor nanoparticles with infrared-to-green and -blue upconversion emission using an emulsion liquid membrane system

Yttrium oxysulfide upconverting phosphor nanoparticles, doped with Yb as a sensitizer and Er (or Ho, Tm) as an activator, have been prepared via a solid-gas reaction using precursor oxalate particles obtained in an emulsion liquid membrane (ELM, water-in-oil-in-water (W/O/W) emulsion) system. The resulting Y(2)O(2)S:Yb,Er particles, mainly smaller than 50 nm in diameter, demonstrated green upconversion emission under infrared excitation (lambdaex = 980 nm) via a two-photon process. Distinct green and blue upconversion emission were also demonstrated under the same infrared excitation from Y(2)O(2)S:Yb,Ho and Y(2)O(2)S:Yb,Tm nanoparticles, respectively. These upconverting phosphor nanoparticles, together with Y(2)O(3):Yb,Er infrared-to-red upconverting phosphor particles, with different emission under the same infrared excitation may be applied to the luminescent reporter materials for the detection of the targeted analyte in multiplexed assays.     

Effect of ZnX (X=F2 and Cl2) as modifier on luminescence properties of Ho3+/Yb3+ doped tellurite glasses

Optical absorption and photoluminescent properties of Ho(3+)/Yb(3+) co-doped tellurite and zinc halide tellurite glasses are investigated. The effect of zinc halides as modifier on the luminescence properties of above mentioned samples has been explored. Two intense upconversion emission bands centered at 546 ((5)F(4), (5)S(2)→(5)I(8)) and 660 ((5)F(5)→(5)I(8)) nm are observed when samples are excited by 976 nm radiation. Zinc halides act as quencher when 976 nm excitation source is used. The up and downconversion emission spectra are recorded with 532 nm excitation source also. In this case also, zinc halides do not show any improvement. The dependence of upconversion intensities on excitation power and temperature is discussed. The power dependence study shows a quadratic dependence of fluorescence intensity on the excitation power while decrement in emission intensity of different transitions at different rates is observed in temperature dependence study. The possible upconversion mechanisms are also discussed in order to understand the energy transfer between Yb(3+) and Ho(3+) ions.     

氮氧自由基单核钬配合物的合成与结构

A novel mononuclear Ho(Ⅲ) nitronyl nitroxide complex [Ho(hfac)₃(NITPhDma)₂], (NITPhDma=2-(4-dimethylamino-phenyl)-4,4,5,5-tetramethylimidazoline-1-oxyl-3-oxide, hfac=hexafluoroacetylacetonate), was synth-esized and structurally characterized by X-ray diffraction. It crystallizes in monoclinic, space group P2₁/n with a=1.274 5(1) nm, b=1.753 1(2) nm, c=2.482 8(2) nm, β=93.753(2)°. The Ho(Ⅲ) ion is eight-coordinated with a distorted dodecahedron environment. Each NITPhDma radical acts as monodentate ligand towards Ho(Ⅲ) ion through the NO group, and the complex molecules are well isolated. CCDC: 775839.     

Li2O-Al2O3-GeO2-P2O5微晶玻璃的微观结构和离子电导率

采用传统熔体冷却法制备了Li3-xAl2-xGex(PO4)3(x=1.1~1.9)体系玻璃,并通过热处理工艺获得了高电导率的微晶玻璃。通过XRD、TEM和交流阻抗等测试方法,研究了该系微晶玻璃的物相组成、微观形貌和锂离子电导率。结果表明:该系统微晶玻璃析出导电主晶相为LiGe2(PO4)3,杂质相为AlPO4和GeO2。当x=1.5时,由于导电主晶相LiGe2(PO4)3晶粒充分长大、分布均匀,所制备微晶玻璃的室温锂离子电导率最高(5.72×10-4 S.cm-1),可以满足全固态锂离子电池对电解质高室温电导率的要求。