弹／粘塑性压力容器的塑性失稳破坏

依据压力容器拉伸塑性失稳破坏特征,计算了旋转薄壁壳压力容器在弹/粘塑性材料下的塑性失稳破坏,文中就圆柱壳形、圆球壳形、抛物线壳形封头等压力容器的失稳状态,分别求出它们的应力应变。     

前屈曲应力状态对组合加肋旋转壳失稳临界压力影响的探讨

推导了包含前屈曲弯矩和横剪力的旋转壳弹性稳定性基本方程.运用Riccati传递矩阵法对组合加肋旋转壳算例进行了稳定性分析,并与假设前屈曲状态为薄膜应力状态计算出的失稳临界压力进行了比较.结果表明,前屈曲弯矩和横剪力对组合加肋旋转壳失稳临界压力的影响较小,随着壳板厚度和肋骨尺寸的增大及肋骨间距的缩短,影响略有增大.因而,分析组合加肋旋转壳弹性稳定性时,前屈曲状态采用薄膜应力状态的假设是合理的.     

静动组合作用下旋转壳拉伸塑性失稳

分析了静动组合作用下几种旋转壳拉伸塑性失稳问题,给出了失稳条件下具有σ_1=A(B+ε_i)″应变强化材料的壳体的应力和应变.     

金属柱壳在爆炸加载断裂中的单旋现象

系列实验结果表明,在较强的滑移爆轰加载下,许多金属材料的旋转柱壳会呈现一种奇特的单旋剪切失稳破坏模式受驱动壳壁结构上众多剪切滑移带及断口取向一致化,在45和135两族剪切带中,出现一族占优的现象。通过高速分幅和X光照相对剪切裂纹在壳壁内、外表的生成发展图像的记录和碎片样品回收,结合过程应力分析,对微剪切断裂发展过程中环向和纵向关联的可能机制进行了分析讨论,但疑点仍较多。在分析柱壳的高应变率失稳行为时,对于与加载条件及几何构形紧密耦合的材料动载剪切强度、各向异性性质所扮演的角色需要进一步认识。剪切断裂的单旋与聚能罩内层无破坏的射流整体旋转现象表现方式和程度虽有差异,但可能有着共同本质,值得深入探索。     

轴向应力波作用下圆柱壳塑性轴对称动力屈曲

运用有限元特征值分析方法对应力波作用下圆柱壳塑性轴对称动力失稳问题进行了研究。基于应力波理论和相邻平衡准则导出了圆柱壳轴对称动力失稳时的特征方程,在分析中同时考虑了应力波效应及横向惯性效应,把圆柱壳塑性动力失稳问题归结为特征值问题。通过引入圆柱壳动力失稳时的波前约束条件实现了此类问题的有限元特征值解法。计算结果揭示了圆柱壳塑性轴对称动力屈曲变形发展的机理,以及轴向应力波和屈曲变形的相互作用规律。     

轴向应力波作用下圆柱壳弹性轴对称动力失稳有限元特征值分析

本文运用有限元特征值分析方法对应力波作用下圆柱壳弹性轴对称动力失稳问题进行了研究。基于应力波理论和相邻平衡准则导出了圆柱壳轴对称动力失稳时的有限元特征方程,在此方程中考虑了应力波效应及横向惯性效应,把圆柱壳弹性动力失稳问题归结为特征值问题。通过引入圆柱壳动力失稳时的波前约束条件实现了此类问题的有限元特征值解法。计算结果揭示了圆柱壳弹性轴对称动力屈曲变形发展的机理,以及轴向应力波和屈曲变形的相互作用规律。     

复合圆柱壳冲击压缩数值模拟及稳定性研究

针对复合圆柱壳在炸药爆轰作用下的动力学响应及在此过程中伴随的失稳问题,研究了其制造工艺中可能出现的缺陷以及圆柱壳中铜线螺旋角和直径对复合圆柱壳稳定性产生的影响。采用SPH-FEM耦合算法,建立了复合圆柱壳二维细节模型,并提出了一种基于圆柱壳内壁粒子速度历史的失稳判据,计算了在不同参数条件下复合圆柱壳的失稳时间及对应的压缩率,对影响复合圆柱壳稳定性的因素进行了评估。分析结果表明,在复合圆柱壳制备过程中存在的折返层缺陷和铜线直径对复合圆柱壳的稳定性有较大影响,而螺旋角度对其稳定性影响不大。     

有环壳过渡段的锥—柱组合壳的应力和稳定性

用解析方法计算了受静水外压载荷作用的有环壳过渡段的锥—柱组合壳中的应力值，并用瑞利法计算了其失稳临界载荷。计算结果说明，利用环壳过渡值锥—柱壳形成光滑连接，可使连接部位的局部应力值显著降低，并使失稳临界载荷有所提高     

圆柱壳受轴向压缩塑性稳定性的实验研究

圆柱壳受轴压的塑性稳定性的理论,曾有很多人进行过大量的探讨,但是,在实验方面研究的文章却发表得较少.本文给出了用AM 和1T 铝合金圆柱壳所做的大量实验.首先描述了观察到的失稳过程,给出了失稳时的最大载荷,它们与不考虑卸载的全量理论所算出的临界载荷符合较好.其次,给出了1T 铝合金圆柱壳塑性失稳和弹性失稳的范围,以及小挠度理论的适用范围.最后,给出了R/h 与失稳时出现轴对称波与菱形波半波数之间的关系.     

关于结构限制失稳的研究进展

限制失稳是指构件失稳时其屈曲变形不能自由发展而受到某种限制性约束的失稳,有时又称单向失稳、接触失稳、约束失稳.这类问题在工业中有大量应用,也是固体力学中的一个经典问题.最常见的实例如应用于地下管道、隧道、压力容器、核反应堆安全壳中的薄衬壳,当薄衬壳发生屈曲时,由于受到外壁的约束,其屈曲行为和一般的壳体屈曲行为不同,这就需要我们发展新的研究方法.另外如受钻井套管横向约束的钻柱的屈曲,复合材料的分层屈曲,电子元器件中的镀层屈曲等也属于限制失稳的范畴.限制失稳问题因其涉及接触问题、单向屈曲、非保守问题等而显得十分复杂,一直没有得到很好的解决.从近年来文献看,限制失稳的研究多集中在压杆、圆环的研究,板、壳的研究相对较少.本文首先简单介绍了限制失稳的一般概念,指出存在的限制约束对结构屈曲特性的影响.然后分别介绍了对于杆、环、板、壳的受限制失稳的研究进展.最后提出了需要进一步深入研究的问题.图11参75      

夹芯圆柱壳在水下爆炸载荷作用下的抗冲击特性

采用声固耦合方法对夹芯圆柱壳和等质量的普通圆柱壳在爆炸载荷作用下的应变、速度和加速度进行有限元计算。结果表明:夹芯防护层对爆炸冲击波可起到较好的衰减作用,即通过芯层的塑性变形,耗散了冲击过程中产生的大部分能量,对里面的圆柱壳体起到较好的保护作用,由于夹芯防护层的存在,与等质量的普通圆柱壳相比,夹芯圆柱壳能够承受更强的爆炸冲击波,降低结构的整体变形。     

Some Approaches to the Solution of Problems on Thin Shells with Variable Geometrical and Mechanical Parameters

A number of approaches to the solution of stress problems for anisotropic inhomogeneous shells in the classical formulation are discussed. A review is made of approaches to the solution of one- and two-dimensional static problems for thin shells with variable parameters and to the solution of stress–strain problems for anisotropic shells of revolution under axisymmetric and non-axisymmetric loading, shallow convexo-convex shells, noncircular cylindrical shells, plates of various shapes, and shells of complex geometry     

正交异性扁壳的等价关系式和不变量

提出各向同性扁壳比拟法,分析满足条件D_3=D_(12)=(D_1D_2)~(1/2)的正交异性扁壳大挠度弯曲和超屈曲问题,导出了正交异性扁壳与各向同性扁壳之间,两种不同正交异性扁壳之间坐标变量、扁壳厚度和曲率半径、荷载、挠度、转角、弯矩、扭矩、中面应力的等价关系式,还证明了等价正交异性扁壳的几个等价不变量。     

Critical loads of shells with high-modulus reinforcement

The analytical method developed to determine the upper and lower critical stresses is applied to cylindrical shells reinforced with stringers and rings. Buckling modes typical of shells reinforced with discrete ribs are considered. The minimum critical loads are determined and compared with available experimental data. Perfect and imperfect ribbed shells with high-modulus reinforcement are studied. It is proved that the effect of small axisymmetric imperfections in such shells is not so drastic as in isotropic shells. Ribs made of a high-modulus material can enhance the stability of shells by a factor of tens     

Nonlinear Theory of Dynamic Stability for Laminated Composite Cylindrical Shells

ＩｎｔｒｏｄｕｃｔｉｏｎＷｈｅｎｃｏｍｐｏｓｉｔｅｃｙｌｉｎｄｒｉｃａｌｓｈｅｌｌｓａｒｅｕｎｄｅｒｔｈｅａｃｔｉｏｎｏｆｄｙｎａｍｉｃｌｏａｄｉｎｇ ,ｔｈｅｙｍａｙｆａｌｌｉｎｄｙｎａｍｉｃｂｕｃｋｌｉｎｇｏｒｄｙｎａｍｉｃｉｎｓｔａｂｉｌｉｔｙ .Ｉｆｔｈｅｄｙｎａｍｉｃｌｏａｄｉｓｓｕｄｄｅｎｌｙａｐｐｌｉｅｄ ,ｏｒｉｔｉｓｃｈａｎｇｉｎｇｉｎｓｔａｎｔａｎｅｏｕｓｌｙ ,ｓｕｃｈａｓｉｍｐｕｌｓｉｖｅｌｏａｄｉｎｇ ,ｔｈｅｎ ,ｄｙｎａｍｉｃｂｕｃｋｌｉｎｇｗｉｌｌｈａｐｐｅｎｆｏｒｔｈｅｓｈ…     

NONLINEAR THEORY OF MULTILAYER SANDWICH SHELLS AND ITS APPLICATION(Ⅲ)──LARGE DEFLECTION AND POSTBUCKLING OF SHALLOW SHELLS

In this paper, exact solutions of large deflection of multilayer sandwich shallow shells under transverse forces and different boundary conditions are presented. Exact results of postbuckling of multilayer sandwich plates, shallow cylindrical shells and nonlinear deflection of general shallow shells such as spherical shells under inplane edge forces are also obtained by the same procedure.     

Stability of corrugated composite noncircular cylindrical shells under external pressure

Cylindrical shells consisting of cylindrical panels of smaller radius and subjected to uniform external pressure are analyzed for stability. The geometrical parameters of the shells are approximated by Fourier series on a discrete set of points. The Timoshenko theory of shells is used. The solution is represented in the form of trigonometric series. It is shown that short-and medium-length shells with cylindrical panels are advantageous over circular shells. By selecting appropriate parameters of the panels, keeping the mass of the shell constant, it is possible to achieve a significant gain in critical loads. The shells under consideration are less effective than isotropic shells. Shells with sinusoidal corrugation under external pressure are of no practical interest __________ Translated from Prikladnaya Mekhanika, Vol. 43, No. 12, pp. 91–102, December 2007.     

Complex equations of flexible circular ring shells overall-bending in a meridian plane and general solution for the slender ring shells

ＩｎｔｒｏｄｕｃｔｉｏｎＥｑｕａｔｉｏｎｓｆｏｒｃｉｒｃｕｌａｒｒｉｎｇｓｈｅｌｌｓａｒｅｄｉｆｆｉｃｕｌｔｔｏｓｏｌｖｅ．Ｔｈｅｒｅｓｅａｒｃｈｏｆｔｈｉｓｐｒｏｂｌｅｍｓｔａｒｔｅｄａｔｔｈｅｂｅｇｉｎｎｉｎｇｏｆｔｈｉｓｃｅｎｔｕｒｙ．Ｉｎｔｈｅｌａｔｅ１９７０ｓａｎｄｅａｒｌｙ１９８０ｓ,Ｗ．Ｚ．Ｃｈｉｅｎ（１９７９,１９８０,１９８１）［１～３］ｒｅｂｕｉｌｔｔｈｅｃｏｍｐｌｅｘｅｑｕａｔｉｏｎｓｏｆａｘｉｓ＿ｓｙｍｍｅｔｒｉｃａｌｌｙｌｏａｄｅｄｒｉｎｇｓｈｅｌｌｓｐｒｅｓｅｎｔｅｄ…     

基于SHPB装置的膨胀圆柱管实验技术

采用改进的SHPB实验装置对45钢薄壁金属圆柱管进行了膨胀断裂加载,完成了不同变形程度 (覆盖圆柱管整个变形及断裂过程)圆柱管的冻结回收实验。回收样品可用于断裂机理研究分析,通过数值模 拟辅助分析和实验数据拟合得到了圆柱管凸起处的径向应变、应变率和环向拉伸应力。通过在圆柱管端粘贴 应变片监测断裂信号的方式,准确判断了圆柱管凸起处发生断裂的时间,以及径向断裂应变、应变率和环向拉 伸断裂应力,在102~104s-1应变率范围内,SHPB实验装置可用于研究金属圆柱管膨胀断裂。     

Timoshenko-Type Theory in the Stability Analysis of Corrugated Cylindrical Shells

A technique is proposed for stability analysis of longitudinally corrugated shells under axial compression. The technique employs the equations of the Timoshenko-type nonlinear theory of shells. The geometrical parameters of shells are specified on discrete set of points and are approximated by segments of Fourier series. Infinite systems of homogeneous algebraic equations are derived from a variational equation written in displacements to determine the critical loads and buckling modes. Specific types of corrugated isotropic metal and fiberglass shells are considered. The calculated results are compared with those obtained within the framework of the classical theory of shells. It is shown that the Timoshenko-type theory extends significantly the possibility of exact allowance for the geometrical parameters and material properties of corrugated shells compared with Kirchhoff–Love theory.