Synthesis and photocatalytic property of N-doped TiO2 nanorods and nanotubes with high nitrogen content

Nano N-doped TiO₂ nanotubes were fabricated by hydrothermally treating N-doped TiO₂ nanorods in a 8 M NaOH solution at 110 °C for 20 h. The N-doped TiO₂ nanorods were synthesized by a solvothermal process with precursor solution containing titanium sulfate, urea, and dichloroethane. The N-doped TiO₂ nanorods and nanotubes were characterized with X-ray diffraction, transmission electron microscopy, and UV-vis spectrophotometry. The nitrogen contents of the N-doped TiO₂ nanorods and nanotubes were reached to high values of 36.9 at.% and 25.7 at.%, respectively. The nitrogen doping narrowed the band gap of the N-doped TiO₂ nanorods and nanotubes and introduced indirect band gap to the powders, which respectively extended the absorption edge to visible light and infrared region. The nanotubes showed larger specific surface area and greater degradation efficiency to methyl orange than the nanorods.     

Influence of growth temperature of TiO2 buffer on structure and PL properties of ZnO films

A series of ZnO films with TiO₂ buffer on Si (1 0 0) substrates were prepared by DC reactive sputtering. Growth temperature of TiO₂ buffer changed from 100 °C to 400 °C, and the influence on the crystal structures and optical properties of ZnO films have been investigated. The XRD results show that the ZnO films with TiO₂ buffer have a hexagonal wurtzite structure with random orientation, and with the increase of growth temperature of TiO₂ buffer, the residual stresses were released gradually. Specially, the UV emission enhanced distinctly and FWHMs (full width half maximum) decreased linearly with the increasing TiO₂ growth temperature. The results all come from the improvement of crystal quality of ZnO films.     

Study on the properties and charge generation in dye-sensitized n-TiO2|dye|p-CuI solid state photovoltaic solar cells

Transparent semiconducting copper iodide (CuI) films were prepared by XeCl Excimer laser and their characteristics are investigated. These films exhibited optical transmittance over 80% in the wavelength range from 400 to 900 nm and minimum resistivity of about 2 kΩ cm⁻¹. The optical absorption of the these films shows a remarkable blue shift compared to that of polycrystalline of CuI, which can be explained from the viewpoint formation of ultra fine of CuI grains. The titanium dioxide (TiO₂) films have been prepared by sol-gel method. The properties of pulsed laser deposited CuI and TiO₂ films in power output of n-TiO₂|dye|p-CuI cells is studied. An efficient charge generation is observed through the illumination of TiO₂ layer of the fabricated n-TiO₂|dye|p-CuI solid state photovoltaic solar cells. From the current-voltage characteristics, the fill factor and power conversion efficiency were about of 45 and 3%, respectively. The maximum photo-current of about 12.5 mA/cm² and photo-voltage of 475 mV under AM 1.5 conditions were obtained for the n-TiO₂|dye|p-CuI solid states photovoltaic solar cells with good reproducibility. Adsorbed dye molecules to the TiO₂ surface act as a relay, especially under illumination through TiO₂ layer in the wave range region of 300-400 nm.     

Transparent nano composite PVA–TiO2 and PMMA–TiO2 thin films: Optical and dielectric properties

Transparent nano composite PVA–TiO₂ and PMMA–TiO₂ thin films were prepared by an easy and cost effective dip coating method. Al/PVA–TiO₂/Al and Al/PMMA–TiO₂/Al sandwich structures were prepared to study the dielectric behavior. The presence of metal–oxide (Ti–O) bond in the prepared films was confirmed by Fourier transform infrared spectroscopy. X-ray diffraction pattern indicated that the prepared films were predominantly amorphous in nature. Scanning electron micrographs showed cluster of TiO₂ nanoparticles distributed over the film surface and also there were no cracks and pin holes on the surface. The transmittance of the films was above 80% in the visible region and the optical band gap was estimated to be about 3.77 eV and 3.78 eV respectively for PVA–TiO₂ and PMMA–TiO₂ films by using Tauc's plot. The determined refractive index (n) values were between 1.6 and 2.3. High value of dielectric constant (?′ = 24.6 and ?′ = 26.8) was obtained for the prepared composite films. The conduction in the composite films was found to be due to electrons. The observed amorphous structure, good optical properties and dielectric behavior of the prepared nano composite thin films indicated that these films could be used in opto-electronic devices and in thin film transistors.     

Effect of surface preparation on the morphology of ZnO nanorods

The effects of Si substrate orientation and surface treatment on the morphology and density of Zinc oxide (ZnO) nanorods were investigated. The size and density of ZnO nanorods were influenced by Si substrate orientation and surface preparation. ZnO nanorods synthesized on the ideally H-terminated Si(1 1 1) prepared with an NH₄F solution resulted in the biggest size and the lowest density. It is suggested that the smoother surface of the Si substrate and lattice shape match with a larger atomic distance result in the increase of the ZnO seedlayer's grain size, which in turn enhances the size of ZnO nanorods grown on it. The optical properties of the ZnO nanorods were affected by their size and crystallinity. The smallest ZnO nanorods with a preferential c-axis orientation synthesized on the HF-treated Si(1 1 1) surface showed the highest intensity ratio of UV to visible emission, and the biggest ZnO nanorods synthesized on the N₂-sparged NH₄F-treated Si(1 1 1) surface showed the lowest intensity ratio of UV to visible emission. Therefore, it can be concluded that Si substrate orientation and surface preparation significantly affect the optical properties of ZnO nanorods.     

TiO2 Wedgy Nanotubes Array Flims for Photovoltaic Enhancement

In this study, TiO₂ wedgy nanotubes with rectangular cross-sections were fabricated on transparent conductive substrates by using TiO₂ nanorods as the precursor via the anisotropic etching route. TiO2 nanotubes with V-shaped hollow structure and the special crystal plane exposed on the tube wall possess nature of high surface area for more dye molecules absorption, and the strong light scattering effects and dual-channel for effective electron transport of the TiO₂ V-shaped nanotubes based dye-sensitized solar cell exhibit a remarkable photovoltaic enhancement compared with the TiO₂ nanorods. The photoanode based on our V-shaped TiO₂ nanotubes with a length of 1.5 μm show a 123% increase of the dye loading and a 182% improvement in the overall conversion efficiency when compared with 4 μm rutile TiO₂ nanorods photoanode.     

Preparation and characterization of iodine-doped mesoporous TiO2 by hydrothermal method

Iodine-doped mesoporous TiO₂ (I/TiO₂) was prepared by hydrothermal method, using tetrabutyl titanate as precursor, potassium iodate as iodine sources. The as-prepared I/TiO₂ catalysts were characterized by UV-vis, XRD, TEM, BET, TG/DTA, XPS and photoluminescence (PL) spectroscopy. Production of OH radicals on the I/TiO₂ surface was detected by the PL technique using terephthalic acid as a probe molecule. The effects of hydrothermal reaction temperature, calcination temperature and iodine doping content on the structure and properties of the catalysts were investigated. The results showed that iodine-doped TiO₂ calcinated at 300 °C have good anatase crystal. The optimal hydrothermal conditions have been determined to be that reaction temperature 120 °C, calcinated temperature 300 °C and added 1.16 mmol iodine dopants. The average particle size of I/TiO₂ synthesized under optimal condition (I-3 sample) is about 3.9 nm. The I-3 photocatalyst contains 100% anatase crystalline phase of TiO₂. BET specific surface area of I-3 sample is184.8 m² g⁻¹ and is 3.67 times that of pure TiO₂ (50.37 m² g⁻¹). Iodine in I/TiO₂ catalyst mainly exists in the form of I₂, and photoactivity of I/TiO₂ catalyst in visible light comes from photosensitize of I₂. I/TiO₂ catalysis shows very high efficiency for the degradation of phenol under visible light.     

Effect of annealing on TiO2 nanoparticles

TiO₂ nanoparticles have been prepared by simple chemical precipitation method and annealed at different temperatures. The as-prepared TiO₂ are amorphous, and they transform into anatase phase on annealing at 450 °C, and rutile phase on annealing at 900 °C. The X-ray diffraction results showed that TiO₂ nanoparticles with grain size in the range of 21–24 nm for anatase phase and 69–74 nm for rutile phase have been obtained. FESEM images show the formation of TiO₂ nanoparticles with small size in structure. The FTIR and Raman spectra exhibited peaks corresponding to the anatase and rutile structure phases of TiO₂. Optical absorption studies reveal that the absorption edge shifts towards longer wavelength (red shift) with increase of annealing temperature.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

Facile synthesis of Nb2O5 nanorod array films and their electrochemical properties

Nb₂O₅ nanorod array films were synthesized by a facile hydrothermal process using niobium metal foil and NH₄F as precursors. The Nb₂O₅ nanorods stand on the niobium metal foil substrate and are less than 100 nm in diameter and about 1 μm in length. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) characterizations indicate that these nanorods have orthorhombic structure and grew longitudinally along 〈0 0 1〉 direction. The nanorod growth mechanism was discussed. Thermal annealing at a temperature below 500 °C did not change the microstructure of nanorods but improve the crystallinity. The Nb₂O₅ nanorod array films have been tested as cathode material for lithium battery, which showed a good specific capacity up to 380 mAh g⁻¹ even after 50 charge/discharge cycles.     

Synthesis and characterization of TiO2/Fe2O3 core-shell nanocomposition film and their photoelectrochemical property

TiO₂/Fe₂O₃ core-shell nanocomposition film has been fabricated via two-step method. TiO₂ nanorod arrays are synthesized by a facile hydrothermal method, and followed by Fe₂O₃ nanoparticles deposited on TiO₂ nanorod arrays through an ordinary chemical bath deposition. The phase structures, morphologies, particle size, chemical compositions of the composites have been characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and ultraviolet-visible (UV-vis) spectrophotometer. The results confirm that Fe₂O₃ nanoparticles of mean size ca. 10 nm coated on the surface of TiO2 NRs. After depositing Fe₂O₃, UV-vis absorption property is induces the shift to the visible-light range, the annealing temperature of 600 °C is the best condition for UV-vis absorption property of TiO₂/Fe₂O₃ nanocomposite film, and increasing Fe content, optical activity are enhanced one by one. The photoelectrochemical (PEC) performances of the as-prepared composite nanorods are determined by measuring the photo-generated currents under illumination of UV-vis light. The TiO₂ NRs modified by Fe₂O₃ show the photocurrent value of 1.36 mA/cm² at 0 V vs Ag/AgCl, which is higher than those of unmodified TiO₂ NRs.     

Enhanced cyclability of CdS/TiO2 photocatalyst by stable interface structure

CdS nanoparticles were in situ deposited on TiO₂ nanosheets and nanorods under hydrothermal conditions, respectively. The effect of CdS–TiO₂ interface structure on hydrogen production activity was mainly investigated under visible light irradiation. The results showed that the TiO₂ nanosheet-based CdS/TiO₂ showed a higher activity and a higher cyclability than the nanorod-based sample due to the stronger interaction of CdS with the (0 0 1) facets of TiO₂ than with the (1 0 1) facets. It was proposed that the strong interaction between CdS nanoparticles and TiO₂ nanosheets effectively refrains the recombination of electrons and holes.     

Correlation between microstructure and optical properties of nano-crystalline TiO2 thin films prepared by sol-gel dip coating

Titanium dioxide thin films have been prepared from tetrabutyl-orthotitanate solution and methanol as a solvent by sol-gel dip coating technique. TiO₂ thin films prepared using a sol-gel process have been analyzed for different annealing temperatures. Structural properties in terms of crystal structure were investigated by Raman spectroscopy. The surface morphology and composition of the films were investigated by atomic force microscopy (AFM). The optical transmittance and reflectance spectra of TiO₂ thin films deposited on silicon substrate were also determined. Spectroscopic ellipsometry study was used to determine the annealing temperature effect on the optical properties and the optical gap of the TiO₂ thin films. The results show that the TiO₂ thin films crystallize in anatase phase between 400 and 800 °C, and into the anatase-rutile phase at 1000 °C, and further into the rutile phase at 1200 °C. We have found that the films consist of titanium dioxide nano-crystals. The AFM surface morphology results indicate that the particle size increases from 5 to 41 nm by increasing the annealing temperature. The TiO₂ thin films have high transparency in the visible range. For annealing temperatures between 1000 and 1400 °C, the transmittance of the films was reduced significantly in the wavelength range of 300-800 nm due to the change of crystallite phase and composition in the films. We have demonstrated as well the decrease of the optical band gap with the increase of the annealing temperature.     

Interaction of Sb ions with Eu ions during the room temperature synthesis of luminescent Sb2O3 nanorods: Probed through Eu luminescence

The interaction of Eu³⁺ with Sb³⁺ ions during the room temperature synthesis of luminescent Sb₂O₃ nanorods is investigated using luminescence and vibrational spectroscopic techniques. Our results demonstrate that well crystalline, oriented Sb₂O₃ nanorods having length of around 3-4 μm, a width of around 100-200 nm and luminescence at around 390 nm can be synthesized at room temperature. Incorporation of Eu³⁺ in these nanorods has been attempted and it is found that Eu³⁺ ions do not have any interaction with nanorods and their orientation. Detailed Eu³⁺ luminescence and XRD studies confirmed that a part of Sb³⁺ ions reacts with Eu³⁺ ions in the presence of hydroxyl ions (present in the medium) to form an amorphous antimony europium hydroxide compound. The amorphous compound on heating at high temperatures leads to its decomposition, giving hydrated Sb(V) oxides and Eu₂O₃ as major phases.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

The influence of titanium on the properties of zinc oxide films deposited by radio frequency magnetron sputtering

TiO₂-doped zinc oxide thin films were deposited on glass substrates by radio frequency (RF) magnetron sputtering with TiO₂-doped ZnO targets in an argon atmosphere. The structural properties of TiO₂-doped ZnO films doped with different TiO₂ contents were investigated. The experimental results show that polycrystalline TiO₂-doped ZnO films had the (0 0 2) preferred orientation. The deposition parameters such as the working pressure and substrate temperature of TiO₂-doped ZnO films were also investigated. The crystalline structure of the TiO₂-doped ZnO films gradually improved as the working pressure was lowered and the substrate temperature was raised. The lowest electrical resistivity for the TiO₂-doped ZnO films was obtained when the Ti addition was 1.34 wt%; its value was 2.50 × 10⁻³ Ω cm, smaller than that found in previous studies. The transmittance of the TiO₂-doped ZnO films in the visible wavelength range was more than 80%. The optical energy gap was related to the carrier concentration, and was in the range of 3.30-3.48 eV.     

Surface modification of nanocrystalline anatase with CTAB in the acidic condition and its effects on photocatalytic activity and preferential growth of TiO2

The nanocrystalline anatase TiO₂, which was synthesized by a sol-hydrothermal process in advance, has successfully modified with cetyltrimethylammonium bromide (CTAB) in the acidic condition as well as in the basic condition. On the basis of the measurements of infrared spectrum and X-ray photoelectron spectroscopy of the resulting TiO₂, together with the phase-transfer experiments, it is suggested that the modification mechanism in the acidic condition is closely related to Br⁻. Interestingly, compared with un-modified TiO₂, the modified TiO₂ exhibits high photocatalytic activity for degrading Rhodamine B (RhB) solution, especially for that modified in the acid. The enhanced photocatalytic activity of modified TiO₂ in the acid is attributed to the role that the Br⁻ can easily capture photo-induced holes and then form active Br, consequently effectively inducing photocatalytic oxidation reactions, based on the surface photovoltage responses of the resulting TiO₂. After that, a one-pot sol-hydrothermal route at the temperature as low as 80 °C is developed to directly synthesize CTAB-modified nanocrystalline TiO₂ with a little preferred growth along 〈0 0 1〉 direction, which can be easily dispersed in the organic system and possess good photocatalytic performance. This work provides a feasible strategy to further improve the photocatalytic performance of nanocrystalline anatase and to synthesize TiO₂ nanocrystals with preferential growth.     

Direct imprinting of ordered and dense TiO2 nanopore arrays by using a soft template for photovoltaic applications

Highly ordered and dense TiO₂ nanopore arrays are directly nanoimprinted on a transparent conductive glass substrate by using a polymethylmethacrylate/polydimethylsiloxane (PMMA/PDMS) composite soft template, which is replicated from an anodic aluminum oxide (AAO) replica mold. Results indicate that heat infiltration under vacuum conditions can ensure complete filling of PMMA into the AAO pores, and that free-standing PMMA nanorods with an aspect ratio more than 5 can be obtained by adjusting the AAO pore depth based on a freeze-drying technique. TiO₂ nanopore arrays with different diameters from 30 to 300 nm and inter-pore distances between 70 and 450 nm can be easily fabricated by using the corresponding templates with different sizes. Preliminary solar cells are also assembled with a heterojunction of conjugated polymer/TiO₂ nanopore arrays. Results indicate that the construction of poly-(3-hexylthiophene) (P3HT)/TiO₂ nanopore arrays can be more helpful in quenching the PL emission of P3HT than that of P3HT/flat TiO₂ film, and a maximum efficiency of about 0.32% can be obtained for a photovoltaic device with a TiO₂/[6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM)/P3HT structure.     

Studies of luminescence properties of ZnO and ZnO:Zn nanorods prepared by solution growth technique

Pyramidal ZnO nanorods with hexagonal structure having c-axis preferred orientation are grown over large area silica substrates by a simple aqueous solution growth technique. The as-grown nanorods were studied using XRD, SEM and UV-vis photoluminescence (PL) spectroscopy for their structural, morphological and optical properties, respectively. Further, the samples have also been annealed under different atmospheric conditions (air, O₂, N₂ and Zn) to study the defect formation in nanorods. The PL spectra of the as-grown nanorods show narrow-band excitonic emission at 3.03 eV and a broad-band deep-level emission (DLE) related to the defect centers at 2.24 eV. After some mild air annealing at 200 °C, fine structures with peaks having energy separation of ∼100 meV were observed in the DLE band and the same have been attributed to the longitudinal optical (LO) phonon-assisted transitions. However, the annealing of the samples under mild reducing atmospheres of N₂ or zinc at 550 °C resulted in significant modifications in the DLE band wherein high intensity green emission with two closely spaced peaks with maxima at 2.5 and 2.7 eV were observed which have been attributed to the V_O and Zn_i defect centers, respectively. The V-I characteristic of the ZnO:Zn nanorods shows enhancement in n-type conductivity compared to other samples. The studies thus suggest that the green emitting ZnO:Zn nanorods can be used as low voltage field emission display (FED) phosphors with nanometer scale resolution.