Microstructure and mechanical properties of Al2O3-Al composite coatings deposited by plasma spraying

Al₂O₃ and Al₂O₃-Al composite coatings were prepared by plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction (XRD), while optical microscopy (OM) and scanning electron microscopy (SEM) were employed to investigate the morphology of impacted droplets, polished and fractured surface, and the element distribution in terms of wavelength-dispersive spectrometer (WDS). Mechanical properties including microhardness, adhesion and bending strength, fracture toughness and sliding wear rate were evaluated. The results indicated that the addition of Al into Al₂O₃ was beneficial to decrease the splashing of impinging droplets and to increase the deposition efficiency. The Al₂O₃-Al composite coating exhibited homogeneously dispersed pores and the co-sprayed Al particles were considered to be distributed in the splat boundary. Compared with Al₂O₃ coating, the composite coating showed slightly lower hardness, whereas the coexistence of metal Al phase and Al₂O₃ ceramic phase effectively improved the toughness, strength and wear resistance of coatings.     

Electrodeposition and characterization of Ni-Y2O3 composite

Nano-sized Y₂O₃ particles were codeposited with nickel by electrolytic plating from a nickel sulfate bath. The effects of the incorporated Y₂O₃ on the structure, morphology and mechanical properties (including microhardness, friction coefficient and wear resistant) of Ni-Y₂O₃ composite coatings were studied. It is observed that the addition of nano-sized Y₂O₃ particles shows apparent influence on the reduction potential and pH of the electrolyte. The incorporated Y₂O₃ increases from 1.56 wt.% to 4.4 wt.% by increasing the Y₂O₃ concentration in the plating bath from 20 to 80 g/l. XRD results reveal that the incorporated Y₂O₃ particles favour the crystal faces (2 0 0) and (2 2 0). SEM and AFM images demonstrate that the addition of Y₂O₃ particles causes a smooth and compact surface. The present study also shows that the codeposited Y₂O₃ particles in deposits decrease the friction coefficient and simultaneously reduce the wear weight loss. Ni-Y₂O₃ composite coatings reach their best microhardness and tribological properties at Y₂O₃ content 4.4 wt.% under the experiment conditions.     

SHS等离子喷涂制备FeAl2O4-Al2O3-Fe纳米复合涂层的研究

利用SHS等离子喷涂技术，将经过机械团聚法制备的Fe₂O₃-Al复合粉体送入等离子焰流，沉积出厚度约为400 μm的复合涂层.利用XRD，SEM 和TEM等检测手段对涂层的成分和组织进行了分析，测定了涂层的显微硬度、断裂韧性以及耐磨性.结果表明涂层为具有纳米结构的FeAl₂O₄-Al₂O₃-Fe纳米复合组织；涂层的显微硬度为HV_100g870；断裂韧性是普通Al₂O₃涂层的2倍；无润滑磨损的耐磨性是普通Al₂O₃涂层的2.5倍. 关键词： SHS等离子喷涂 纳米涂层 断裂韧性     

Preparation and characterization of nickel nano-Al2O3 composite coatings by sediment co-deposition

Ni-Al₂O₃ composite coatings were prepared by using sediment co-deposition (SCD) technique and conventional electroplating (CEP) technique from Watt's type electrolyte without any additives. The microstructure, hardness, and wear resistance of resulting composites were investigated. The results show that the incorporation of nano-Al₂O₃ particles changes the surface morphology of nickel matrix. The preferential orientation is modified from (2 0 0) plane to (1 1 1) plane. The microhardness of Ni-Al₂O₃ composite coatings in the SCD technique are higher than that of the CEP technique and pure Ni coating and increase with the increasing of the nano-Al₂O₃ particles concentration in plating solution. The wear rate of the Ni-Al₂O₃ composite coating fabricated via SCD technique with 10 g/l nano-Al₂O₃ particles in plating bath is approximately one order of magnitude lower than that of pure Ni coating. Wear resistance for SCD obtained composite coatings is superior to that obtained by the CEP technique. The wear mechanism of pure Ni and nickel nano-Al₂O₃ composite coatings are adhesive wear and abrasive wear, respectively.     

The tribology properties of alumina/silica composite nanoparticles as lubricant additives

The as-prepared alumina/silica (Al₂O₃/SiO₂) composite nanoparticles were synthesized with a hydrothermal method and modified by silane coupling agent. The tribological properties of the modified Al₂O₃/SiO₂ composite nanoparticles as lubricating oil additives were investigated by four-ball and thrust-ring tests in terms of wear scar diameter, friction coefficient, and the morphology of thrust-ring. It is found that their anti-wear and anti-friction performances are better than those of pure Al₂O₃ or SiO₂ nanoparticles. When the optimized concentration of nanoparticle additive is 0.5 wt.%, the diameters of wear scar and friction coefficients are both smallest. Such modified composite nanoparticles can adsorb onto the friction surfaces, which results in rolling friction. Therefore, the friction coefficient is reduced.     

Preparation and wear resistance of pulse electrodeposited Ni-W/Al2O3 composite coatings

The aim of this work is to obtain the electroplating parameters for preparation of Ni-W/Al₂O₃ composite coating with high tungsten content, high micro-hardness and excellent wear resistance by pulse plating procedure. Our results showed that the duty cycle is a dominant parameter for the tungsten content in the coating and the tungsten content increases significantly with increasing duty cycle. The further analysis showed the great influence of tungsten content on micro-hardness of the coating. A maximum micro-hardness of about 859 Hv was obtained in pulse electrodeposited Ni-W/Al₂O₃ composite with tungsten content of 40 wt.% at a peak current density of 20 A/dm², a duty cycle of 80%, a pulse frequency of 1000 Hz and a particle loading of 10 g/L alumina in the plating bath. Although the hardness of Ni-W/Al₂O₃ composite coating was only slightly affected by the alumina content of the deposits prepared in present investigation, the alumina content effect on the tribological characteristic of Ni-W/Al₂O₃ composite coatings is significant. The friction coefficient was lowered to 0.25 and the wear loss was reduced to 1.05 mg by setting the control factors according to the values mentioned above for obtaining the coating with the highest micro-hardness.     

Preparation and characterization of the electrodeposited Cr-Al2O3/SiC composite coating

To increase the SiC content in Cr-based coatings, Cr-Al₂O₃/SiC composite coatings were plated in Cr(VI) baths which contained Al₂O₃-coated SiC powders. The Al₂O₃-coated SiC composite particles were synthesized by calcining the precursor prepared by heterogeneous deposition method. The transmission electron microscopy analysis of the particles showed that the nano-SiC particle was packaged by alumina. The zeta potential of the particles collected from the bath was up to +23 mV, a favorable condition for the co-deposition of the particles and chromium. Pulse current was used during the electrodeposition. Scanning Electron Microscopy (SEM) indicated that the coating was compact and combined well with the substrate. Energy dispersive X-ray analysis of Cr-Al₂O₃/SiC coatings demonstrated that the concentration of SiC in the coating reached about 2.5 wt.%. The corrosion behavior of the composite coating was studied by potentiodynamic polarization and electrochemical impedance spectroscopy techniques. The data obtained suggested that the Al₂O₃/SiC particles significantly enhanced the corrosion resistance of the composite coating in 0.05 M HCl solution.     

Atmospheric reactive plasma sprayed Fe-Al2O3-FeAl2O4 composite coating and its property evaluation

In the present study, Fe-Al₂O₃-FeAl₂O₄ composite coatings were successfully deposited by reactive plasma sprayed Al/Fe₂O₃ agglomerated powder. Phase composition and microstructure of the coatings were determined by XRD and SEM. The results indicated that the composite coatings were principally composed of three different phases, i.e. FeAl₂O₄ phase as main framework, dispersed ball-like Fe-rich phase, and small splats of Al₂O₃ phase, and it was thought that the in situ synthesized metal phase was helpful to toughen the coating matrix. According to the results of the indentation and frictional wear tests, the composite coating exhibited excellent toughness and anti-friction properties in comparison with conventional Al₂O₃ monophase coating, though its microhardness value was a little lower than that of Al₂O₃ coating. The formation mechanism and the toughening mechanism of the composite coating were clarified in detail.     

Microstructure and properties of Ni-Co/nano-Al2O3 composite coatings by pulse reversal current electrodeposition

Ni-Co/nano-Al₂O₃ (Ni-Co/Al₂O₃) composite coatings were prepared under pulse reversal current (PRC) and direct current (dc) methods respectively. The microstructure of coatings was characterized by means of XRD, SEM and TEM. Both the Ni-Co alloy and composite coatings exhibit single phase of Ni matrix with face-centered cubic (fcc) crystal structure, and the crystal orientation of the Ni-Co/Al₂O₃ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with alloy coatings. The hardness, anti-wear property and macro-residual stress were also investigated. The results showed that the microstructure and performance of the coatings were greatly affected by Al₂O₃ content and the electrodeposition methods. With the increasing of Al₂O₃ content, the hardness and wear resistance of the composite coatings enhanced. The PRC composite coatings exhibited compact surface, high hardness, better wear resistance and lower macro-residual stress compared with that of the dc composite coatings.     

Structural and Tribological Properties of Polytetrafluoroethylene Composites Filled with Glass Fiber and Al2O3 in Atomic Oxygen Environment

Effects of atomic oxygen (AO) irradiation on the structural and tribological behaviors of polytetrafluoroethylene (PTFE) composites filled with both glass fibers and Al₂O₃ were investigated in a ground-based simulation facility, in which the average energy of AO was about 5 eV and the flux was 5.0 × 10¹⁵/cm² s. It was found that AO irradiation first induced the degradation of PTFE molecular chains on the sample surface, and then resulted in a change of surface morphology. The addition of Al₂O₃ filler significantly increased the AO resistance property of PTFE composites. Friction and wear tests indicated that AO irradiation affected the wear rate and increased the friction coefficient of specimens. The PTFE composite containing 10% Al₂O₃ exhibit the best AO resistance and lower wear rate after long time AO irradiation.     

Preparation and characterization of NiFe2O4/NiO composite film via a single-source precursor route

NiFe₂O₄/NiO nanocomposite thin films have been successfully prepared through a facile route using nickel iron layered double hydroxide (NiFe-LDH) as a single-source precursor. This synthetic approach mainly involves the formation of NiFe-LDH film by casting the slurry of NiFe-LDH precursor on the α-Al₂O₃ substrate, followed by high-temperature calcination. The composition, microstructure and properties of the films were characterized in detail by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDX) and vibrating sample magnetometer (VSM). The results indicate that NiFe₂O₄/NiO composite film was composed of granules with diameter less than 100 nm, and the thickness of the film was in the range 1-2 μm. The magnetization of the film can be tuned by alternating the Ni/Fe molar ratio of LDH precursor. In addition, the method developed should be easily extended to fabricate other MFe₂O₄/MO composite film systems with specific applications just by an appropriate combination of divalent/trivalent composition in the precursor of LDHs.     

Enhanced water vapor barrier properties for biopolymer films by polyelectrolyte multilayer and atomic layer deposited Al2O3 double-coating

Commercial polylactide (PLA) films are coated with a thin (20 nm) non-toxic polyelectrolyte multilayer (PEM) film made from sodium alginate and chitosan and additionally with a 25-nm thick atomic layer deposited (ALD) Al₂O₃ layer. The double-coating of PEM + Al₂O₃ is found to significantly enhance the water vapor barrier properties of the PLA film. The improvement is essentially larger compared with the case the PLA film being just coated with an ALD-grown Al₂O₃ layer. The enhanced water vapor barrier characteristics of the PEM + Al₂O₃ double-coated PLA films are attributed to the increased hydrophobicity of the surface of these films.     

Effect of Al content on the properties of Cr1−xAlxC films prepared by RF reactive magnetron sputtering

Cr_1−xAl_xC films were deposited on high-speed steel by RF reactive magnetron sputtering. In this study, we aimed to identify the effect of the Al content on the properties of Cr_1−xAl_xC films. We found that Cr_1−xAl_xC films exhibited a fine columnar grain microstructure with some special characteristics, such as high hardness of Hv 1426, a low friction coefficient of 0.29, and a large contact angle of 90° for x = 0.18. Furthermore, an increase in Al content resulted in a decrease in film hardness and an increase in contact angle. Moreover, on annealing at 923 K, the mechanical properties of the films improved and a dense protective film of complex Cr₂O₃ and Al₂O₃ oxides was formed on the surface for better wear resistance, which will ultimately increase the lifetime of the high-speed steel substrate.     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

2-2型磁电复合薄膜CoFe2O4/Pb(Zr0.53Ti0.47)O3静磁耦合

运用溶胶-凝胶法在Pt/Ti/SiO₂/Si基片上旋涂制备了2-2型CoFe₂O₄/Pb(Zr_0.53Ti_0.47)O₃磁电复合薄膜．制备的磁电薄膜结构为基片/PZT/CFO/PZT*/CFO/PZT,通过改变中间层PZT*溶胶的浓度,改变磁性层间距以及静磁耦合的大小．SEM结果表明,复合薄膜结构致密,呈现出界面清晰平整的多层结构．制备的复合薄膜具有较好的铁电与铁磁性能．实验还研究了静磁耦合对薄膜磁电性能的影响,结果表明,随着复合薄膜磁性层间距的减小,静磁耦合效应的增加,磁电电压系数有逐渐增大的趋势.     

Electrodeposition and tribological properties of Ni-SrSO4 composite coatings

Ni-SrSO₄ composite coatings were electrodeposited on superalloy Inconel 718 from a Watts electrolyte containing a SrSO₄ suspension. Ni-SrSO₄ coatings were investigated by scanning electron microscope, microhardness tester, and friction and wear tester in sliding against a bearing steel ball under unlubricated condition. The incorporation of SrSO₄ into Ni matrix increases the microhardness of electrodeposited coatings. Ni-SrSO₄ composite coating exhibits a distinctly low friction coefficient and a small wear rate as contrasted with pure Ni coating and the substrate. The effect of SrSO₄ particles on microstructure and tribological properties of Ni-SrSO₄ composite coatings is discussed.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.     

Si-Al2O3复合薄膜的室温铁磁性

在Si-Al₂O₃复合薄膜中观察到室温铁磁性.Si的体积百分比为15 %的Si-Al₂O₃复合薄膜的磁性最强.Si的含量影响样品的磁有序,在样品中观察到了明显的磁畴.在不同气氛下,对样品进行快速热退火.退火样品的磁性测试结果的差别表明氧空位不是样品铁磁性的主要来源.我们认为铁磁性来源于Si与Al₂O₃基质界面之间的缺陷的磁耦合.改变Si的含量可以改变缺陷密度,从而控制铁磁耦合强度. 关键词： 2O₃薄膜')" href="#">Al₂O₃薄膜 室温铁磁性 掺杂 交换相互作用     

Microstructure and properties of TiB2-containing coatings prepared by arc spraying

Low cost arc spraying and cored wires were used to deposit composite coatings consisting of TiB₂ and TiB₂/Al₂O₃ hard particles in a Ni(Cr) and stainless steel 304L matrix. Four coatings were prepared namely Ni(Cr)-TiB₂, Ni(Cr)-TiB₂/Al₂O₃, 304L-TiB₂ and 304L-TiB₂/Al₂O₃. The microstructural characteristics of powders and coatings were observed by scanning electron microscopy (SEM). Phase compositions of powders were analyzed by X-ray diffraction (XRD). Although all the analyzed coatings exhibited similar lamella structure, remarkable differences not only in the morphology of hard phase and matrix but also in the size and distribution of hard phases were observed from one coating to another. Tribological behavior of the coatings was analyzed in room temperature dry sliding wear tests (block-on-ring configuration), under 75 N at low velocity (0.5 m/s). The coatings showed far high wear resistance than low carbon steel substrate under same conditions examined. Wear loss of 304L-TiB₂ and Ni(Cr)-TiB₂ coatings were lower nearly 15 times than that of steel substrate. TiB₂ hard phases in coatings bonded well with metal matrix contributed to high wear resistance.     

Morphological and optical properties of sol-gel derived 6SrO·6BaO·7Al2O3 thin films

A novel 6SrO·6BaO·7Al₂O₃ (S6B6A7) thin film deposited onto soda lime float glass via sol-gel dip coating technique is reported. The morphological and compositional properties of the S6B6A7 thin films have been investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) revealing that the films were composed of S6B6A7 nanoparticles. The optical properties of the S6B6A7 films are affected by sol concentration, film thickness and annealing temperature as revealed by UV-vis transmittance. The transparency of S6B6A7 films improved on increasing annealing temperature up to 450 °C in air. The S6B6A7 films prepared using 2, 5, and 8 (wt.%) sols and annealed at 450 °C exhibit an average transmittance of over ∼91% in wide visible range.