Effects of Grafting Density and Film Thickness on the Adhesion of Staphylococcus epidermidis to Poly(2‐hydroxy ethyl methacrylate) and Poly(poly(ethylene glycol)methacrylate) Brushes

Thin polymer films that prevent the adhesion of bacteria are of interest as coatings for the development of infection‐resistant biomaterials. This study investigates the influence of grafting density and film thickness on the adhesion of Staphylococcus epidermidis to poly(poly(ethylene glycol)methacrylate) (PPEGMA) and poly(2‐hydroxyethyl methacrylate) (PHEMA) brushes prepared via surface‐initiated atom transfer radical polymerization (SI‐ATRP). These brushes are compared with poly(ethylene glycol) (PEG) brushes, which are obtained by grafting PEG onto an epoxide‐modified substrate. Except for very low grafting densities (ρ = 1%), crystal violet staining experiments show that the PHEMA and PPEGMA brushes are equally effective as the PEG‐modified surfaces in preventing S. epidermis adhesion and do not reveal any significant variations as a function of film thickness or grafting density. These results indicate that brushes generated by SI‐ATRP are an attractive alternative to grafted‐onto PEG films for the preparation of surface coatings that resist bacterial adhesion.

     

表面引发的原子转移自由基聚合法在聚偏二氟乙烯表面制备可控的聚甲基丙烯酸甲酯刷

采用表面引发的原子转移自由基聚合法(ATRP)在聚偏二氟乙烯(PVDF)表面制备结构可控的聚甲基丙烯酸甲酯刷。通过碱处理和紫外光照溴代的方法,将ATRP引入到PVDF表面; 然后采用ATRP法将甲基丙烯酸甲酯接枝到溴代的PVDF表面。采用傅里叶变换红外光谱和X-射线光电子能谱对改性前后PVDF表面的结构进行了表征。结果表明甲基丙烯酸甲酯成功地接枝到了PVDF表面。     

Atom transfer radical polymerization directly from poly(vinylidene fluoride): Surface and antifouling properties

The direct preparation of grafting polymer brushes from commercial poly (vinylidene fluoride) (PVDF) films with surface‐initiated atom transfer radical polymerization (ATRP) is demonstrated. The direct initiation of the secondary fluorinated site of PVDF facilitated grafting of the hydrophilic monomers from the PVDF surface. Homopolymer brushes of 2‐(N,N‐dimethylamino)ethyl methacrylate (DMAEMA) and poly (ethylene glycol) monomethacrylate (PEGMA) were prepared by ATRP from the PVDF surface. The chemical composition and surface topography of the graft‐functionalized PVDF surfaces were characterized by X‐ray photoelectron spectroscopy, attenuated total reflectance/Fourier transform infrared spectroscopy, and atomic force microscopy. A kinetic study revealed a linear increase in the graft concentration of poly[2‐(N,N‐dimethylamino)ethyl methacrylate] (PDMAEMA) and poly[poly(ethylene glycol) monomethacrylate] (PPEGMA) with the reaction time, indicating that the chain growth from the surface was consistent with a controlled or living process. The living chain ends were used as macroinitiators for the synthesis of diblock copolymer brushes. The water contact angles on PVDF films were reduced by the surface grafting of DMAEMA and PEGMA. Protein adsorption experiments revealed a substantial antifouling property of PPEGMA‐grafted PVDF films and PDMAEMA‐grafted PVDF films in comparison with the pristine PVDF surface. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3434–3443, 2006     

Surface grafted sulfobetaine polymers via atom transfer radical polymerization as superlow fouling coatings

One of the sulfobetaine methacrylate (SBMA) monomers, N-(3-sulfopropyl)-N-(methacryloxyethyl)-N,N-dimethylammonium betaine, was polymerized onto initiator-covered gold surfaces using atom transfer radical polymerization (ATRP) to form uniform polymer brushes. Self-assembled monolayers (SAMs) with ATRP initiators were characterized by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The thickness of grafted poly(SBMA) films was measured by ellipsometry. Fibrinogen adsorption on poly(SBMA) grafted surfaces was measured with a surface plasmon resonance (SPR) sensor. Two approaches were compared to graft ATRP initiators onto gold surfaces for surface polymerization and subsequent protein adsorption on these polymer grafted surfaces. The first was to prepare a SAM from omega-mercaptoundecyl bromoisobutyrate onto a gold surface. Superlow fouling surfaces with well-controlled poly(SBMA) brushes were achieved using this approach (e.g., fibrinogen adsorption <0.3 ng/cm2). The second approach was to react bromoisobutyryl bromide with a hydroxyl-terminated SAM on a gold surface. Although protein adsorption decreased as the density of surface initiators increased, the surface prepared using the second approach was not able to achieve as low protein adsorption as the first approach. Key parameters to achieve superlow fouling surfaces were studied and discussed.     

Synthesis of well‐defined polymer brushes on the surface of zinc antimonate nanoparticles through surface‐initiated atom transfer radical polymerization

Zinc antimonate nanoparticles consisting of antimony and zinc oxide were surface modified in a methanol solvent medium using triethoxysilane‐based atom transfer radical polymerization (ATRP) initiating group (i.e.,) 6‐(2‐bromo‐2‐methyl) propionyloxy hexyl triethoxysilane. Successful grafting of ATRP initiator on the surface of nanoparticles was confirmed by thermogravimetric analysis that shows a significant weight loss at around 250–410 °C. Grafting of ATRP initiator onto the surface was further corroborated using Fourier transform Infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS). The surface‐initiated ATRP of methyl methacrylate (MMA) mediated by a copper complex was carried out with the initiator‐fixed zinc antimonate nanoparticles in the presence of a sacrificial (free) initiator. The polymerization was preceded in a living manner in all examined cases; producing nanoparticles coated with well defined poly(methyl methacrylate) (PMMA) brushes with molecular weight in the range of 35–48K. Furthermore, PMMA‐grafted zinc antimonate nanoparticles were characterized using Thermogravimetric analysis (TGA) that exhibit significant weight loss in the temperature range of 300–410 °C confirming the formation of polymer brushes on the surface with the graft density as high as 0.26–0.27 chains/nm². The improvement in the dispersibility of PMMA‐grafted zinc antimonate nanoparticles was verified using ultraviolet‐visible spectroscopy and transmission electron microscopy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Surface‐initiated atom transfer radical polymerization from porous poly(tetrafluoroethylene) membranes using the C?F groups as initiators

This work reports the surface‐initiated atom transfer radical polymerization (ATRP) from hydrogen plasma‐treated porous poly(tetrafluoroethylene) (PTFE) membranes using the C? F groups as initiators. Hydrogen plasma treatment on PTFE membrane surfaces changes their chemical environment through defluorination and hydrogenation reactions. With the hydrogen plasma treatment, the C? F groups of the modified PTFE membrane surface become effective initiators of ATRP. Surface‐initiated ATRP of poly(ethylene glycol) methacrylate (PEGMA) is carried out to graft PPEGMA chains to PTFE membrane surfaces. The chain lengths of poly(PEGMA) (PPEGMA) grafted on PTFE surfaces increase with increasing the reaction time of ATRP. Furthermore, the chain ends of PPEGMA grown on PTFE membrane surfaces then serve as macroinitiators for the ATRP of N‐isopropylacrylamide (NIPAAm) to build up the PPEGMA‐b‐PNIPAAm block copolymer chains on the PTFE membrane surfaces. The chemical structures of the modified PTFE membranes are characterized using X‐ray photoelectron spectroscopy. The modification increases the surface hydrophilicity of the PTFE membranes with reductions in their water‐contact angles from 120° to 60°. The modified PTFE membranes also show temperature‐responsive properties and protein repulsion features owing to the presence of PNIPAAM and PPEGMA chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2076–2083, 2010     

结构规整的高密度两亲性接枝聚合物刷的合成及其自组装研究

大分子单体通过两种可控聚合方法, 即开环易位聚合(ROMP)和原子转移自由基聚合(ATRP)的联用, 合成一种新型两亲性接枝聚合物刷. 具有高环张力的降冰片烯单侧链大分子单体norbornene-graft-poly(ε-caprolactone)/Br (PCL- NBE-Br)首先进行ROMP反应, 生成聚合物主链, 每个单体单元上含有一条PCL链和一个溴官能团; 然后用含溴的ROMP聚合物poly(norbornene)-graft-poly(ε-caprolactone)/Br (PCL-PNBE-Br)作为大分子引发剂引发单体2-(dimethyl- amino)ethyl methacrylate)的ATRP反应, 生成结构明确的高密度两亲性接枝聚合物刷poly(norbornene)-graft-poly(ε- caprolactone)/poly(2-(dimethylamino)ethyl methacrylate) (PCL-PNBE-PDMAEMA), 其主链每个单体单元上均含有一条疏水性PCL接枝链和一条亲水性PDMAEMA接枝链. 最后, 研究此类高密度两亲性接枝聚合物刷的自组装行为, 用动态激光光散射(DLS)研究其在混合溶剂(THF/H2O)中的胶束行为, 考察胶束溶液的浓度以及不同长度的亲水性接枝链对胶束尺寸的影响; 利用透射电镜(TEM)观察胶束为球形, 具有类似线团或草莓状的形态.     

Controlled adhesion of Salmonella Typhimurium to poly(oligoethylene glycol methacrylate) grafts

Poly(oligoethylene glycol methacrylate), POEGMA, brushes were prepared by surface‐initiated atom transfer radical polymerization (SI‐ATRP) on gold‐coated silicon wafers. Prior to ATRP, the substrates were grafted by brominated aryl initiators via the electrochemical reduction of a noncommercial parent diazonium salt of the formula BF₄^?, ⁺N₂‐C₆H₄‐CH(CH₃)Br. The diazonium‐modified gold plates (Au‐Br) served as macroinitiators for ATRP of OEGMA which resulted in hydrophilic surfaces (Au‐POEGMA) that could be used for two distinct objectives: (i) resistance to fouling by Salmonella Typhimurium; (ii) specific recognition of the same bacteria provided that the POEGMA grafts are activated by anti‐Salmonella. The Au‐POEGMA plates were characterized by XPS, polarization modulation‐infrared reflection‐absorption spectroscopy (PM‐IRRAS) and contact angle measurements. Both Beer‐Lambert equation and Tougaard's QUASES software indicated a POEGMA thickness that exceeds the critical ～10 nm value necessary for obtaining a hydrophilic polymer with effective resistance to cell adhesion. The Au‐POEGMA slides were further activated by trichlorotriazine (TCT) in order to covalently bind anti‐Salmonella antibodies (AS). The antibody‐modified Au‐POEGMA specimens were found to specifically attach Salmonella Typhimurium bacteria. This work is another example of the diazonium salt/ATRP process to provide biomedical polymer surfaces. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis and gas permeation properties of poly(vinyl chloride)‐graft‐poly(vinyl pyrrolidone) membranes

A series of amphiphilic graft copolymers consisting of poly(vinyl chloride) (PVC) main chains and poly(vinyl pyrrolidone) (PVP) side chains, i.e. PVC‐g‐PVP, was synthesized via atom transfer radical polymerization (ATRP), as confirmed by ¹H NMR, FT‐IR spectroscopy, and gel permeation chromatography (GPC). Transmission electron microscope (TEM) and small angle X‐ray scattering (SAXS) analysis revealed the microphase‐separated structure of PVC‐g‐PVP and the domain spacing increased from 21.4 to 23.9 nm with increasing grafting degree. All the membranes exhibited completely amorphous structure and high Young's modulus and tensile strength, as revealed by wide angle X‐ray scattering (WAXS) and universal testing machine (UTM). Permeation experimental results using a CO₂/N₂ (50/50) mixture indicated that as an amount of PVP in a copolymer increased, CO₂ permeability increased without the sacrifice of selectivity. For example, the CO₂ permeability of PVC‐g‐PVP with 36 wt% of PVP at 35°C was about four times higher than that of the pristine PVC membrane. This improvement resulted from the increase of diffusivity due to the disruption of chain packing in PVC by the grafting of PVP, as confirmed by WAXS analysis. Copyright © 2011 John Wiley & Sons, Ltd.     

Hydrophilic Modification of Microporous Polysulfone Membrane via Surface‐Initiated Atom Transfer Radical Polymerization and Hydrolysis of Poly(glycidylmethacrylate)

Poly(glycidylmethacrylate) (PGMA) brushes were grafted from chloromethylated polysulfone (CMPSF) membrane surface by surface‐initiated atom transfer radical polymerization (SI‐ATRP), and the grafting was followed by hydrolysis of epoxy groups in the grafting chains to improve the membrane's hydrophilic property. Fourier transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS) measurements confirmed the successful grafting and hydrolysis of PGMA. The grafting degree of the monomer, measured by periodic acid titration and gravimetric analysis, increased linearly with the polymerization time, while the static water contact angle of the membrane grafted with PGMA or hydrolyzed PGMA linearly decreased. In comparison with the PGMA‐grafted membranes, the hydrolyzed PGMA‐grafted membranes possess stronger hydrophilicity as indicated by their contact angle and hydration capacity, and as a result they have an improved antifouling property. Therefore, the control of the hydrophilicity of PSF membrane could be realized through adjusting the polymerization time and transforming the functional groups in the grafting chain.     

Thermoresponsive coatings strongly adhering to (semi)conducting surfaces

Thermoresponsive brushes have been efficiently grafted onto (semi)conductive surfaces by a two-step process. In the first step, poly(N-succinimidyl acrylate) chains have been chemisorbed onto silicon or stainless steel by the electrografting method. Then, these modified electrodes were immersed in isopropylamine in order to transform the grafted chains to the thermoresponsive poly(N-isopropyl acrylamide). The thermal response of these brushes has been shown by AFM. This straightforward grafting process is quite attractive for surface modification in confined media and is thus promising for microfludics application.     

Construction of hydroxyl‐terminated poly(N‐isopropylacrylamide) brushes on silicon wafer via surface‐initiated atom transfer radical polymerization

Surface‐initiated atom transfer radical polymerization (SI‐ATRP) of N‐isopropylacrylamide (NIPAM) on silicon wafer in the presence of 2‐mercaptoethanol (ME) chain transfer agent was conducted in attempt to create controllable hydroxyl‐terminated brushes. The initiator‐immobilized substrate, was prepared by the esterification of hydroxyl groups on silicon wafer with 2‐bromopropionyl bromide (2‐BPB); followed by the ATRP of NIPAM using a catalyst system, that is, Cu(I)Br/2,2′‐bipyridine (2,2′‐bpy) and a chain transfer agent, that is, ME. The formation of homogeneous tethered poly(N‐isopropylacrylamide) (poly(NIPAM) brushes with hydroxyl end‐group, whose thickness can be tuned by chancing ME concentration, is evidenced by using the combination of grazing angle attenuated total reflectance‐Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, ellipsometry, atomic force microscopy, gel permeation chromatography, and water contact‐angle measurements. The calculation of grafting parameters from experimental measurements indicated the synthesis of densely grafted poly(NIPAM) films with hydroxyl end‐group on silicon wafer and allowed us to predict a ME concentration for forming a “brush” conformation for the chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3880–3887, 2010     

Preparation of dual stimuli‐responsive PET track‐etched membrane by grafting copolymer using ATRP

A dual stimuli‐responsive (pH and thermo) polyethylene terephthalate (PET) track‐etched membrane has been prepared using atom transfer radical polymerization (ATRP). First, ATRP initiator 2‐bromoisobutyryl bromide was anchored onto the membrane surface. Then, 2‐hydroxyethyl‐methacrylate (HEMA) and N‐isopropylacrylamide (NIPAAm) were grafted onto the membrane surface using ATRP. X‐ray photoelectron spectroscopy, ATR‐Fourier transform infrared spectroscopy, scanning electron microscopy and thermogravimetric analysis were used to characterize the membrane structure and thermal properties; water flux measurement was used to investigate the double stimuli‐responsive property of the obtained membrane. The results indicate that the PHEMA and PNIPAAm binary grafted PET track‐etched membrane has double environmental responsiveness. This method provides a potential modification method for preparing functional membranes. Copyright © 2012 John Wiley & Sons, Ltd.     

Construction of a comb-like glycosylated membrane surface by a combination of UV-induced graft polymerization and surface-initiated ATRP

Carbohydrate residues are found on the extracellular side of the cell membrane. They form a protective coating on the outer surface of the cell and are involved in intercellular recognition. Synthetic carbohydrate-based polymers, so-called glycopolymers, are emerging as important well-defined tools for investigating carbohydrate-based biological processes and for simulating various functions of carbohydrates. In this work, the surface of a polypropylene microporous membrane (PPMM) was modified with comb-like glycopolymer brushes by a combination of UV-induced graft polymerization and surface-initiated atom-transfer radical polymerization (ATRP). 2-Hydroxyethyl methacrylate (HEMA) was first grafted to the PPMM surface under UV irradiation in the presence of benzophenone and ferric chloride. ATRP initiator was then coupled to the hydroxyl groups of poly(HEMA) brushes. Surface-initiated ATRP of a glycomonomer, D-gluconamidoethyl methacrylate, was followed at ambient temperature in aqueous solvent. Water had a significant acceleration effect on the ATRP process; however, loss of control over the polymerization process was also observed. The addition of CuBr2 to the ATRP system largely increased the controllability at the cost of the polymerization rate. The grafting of HEMA, the coupling of ATRP initiator to the hydroxyl groups, and the surface-initiated ATRP were confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy.     

Controlled pore functionalization of poly(ethylene terephthalate) track-etched membranes via surface-initiated atom transfer radical polymerization

A new method for surface-initiated atom transfer radical polymerization (ATRP) on the technical polymer poly(ethylene terephthalate) (PET) has been developed which allows controlling and estimating the layer thickness of the grafted polymer in the isocylindrical pores of track-etched membranes. After PET surface treatment by oxidative hydrolysis, the bromoalkyl initiator was immobilized on the PET surface in a two-step solid-phase reaction; the isoporous membrane structure was preserved, and the pore diameter was increased from 760 to 790 nm. Poly(N-isopropylacrylamide) (PNIPAAm) was grafted under ATRP conditions from a methanol/water mixture at room temperature. Both monomer concentration and reaction time could be used as parameters to adjust the degree of grafting. Effective grafted layer thickness and its response to temperature were estimated from pure water permeability. All data, especially the high polymer densities (0.37 g/cm3) in the swollen layers at 25 degrees C, indicate that grafted PNIPAAm with a "brush" structure has been achieved. For dry PNIPAAm layer thicknesses on the PET pore walls of up to 80 nm, a temperature-induced swelling/deswelling ratio of approximately 3 had been observed. Reduction of the brush grafting density, via composition of the reaction mixture used in solid-phase synthesis for initiator immobilization, led to an increase of that swelling/deswelling ratio. Further, density and temperature response of the grafted PNIPAAm layers synthesized via ATRP were compared with those obtained in the same membranes by less controlled photografting, leading to lower grafting density and larger gradients in grafted layer density and, consequently, much higher swelling/deswelling ratios (>15).     

Scale‐up synthesis of hyperbranched poly(amidoamine)‐grafted ultrafine silica using dendrimer synthesis methodology in solvent‐free dry‐system

Scale‐up synthesis of hyperbranched poly(amidoamine)‐grafted ultrafine silica was successfully achieved by using dendrimer synthesis methodology in solvent‐free dry‐system. The poly(amidoamine) was allowed to grow from silica surface by repeating two steps: (1) Michael addition of methyl acrylate (MA) to amino group on the surface and (2) amidation of terminal ester group with ethylenediamine (EDA). MA was sprayed onto silica having amino group and the silica agitated at 300 rpm at 50 °C. After the reaction, unreacted MA was removed under vacuum. Then EDA was sprayed and the reaction was conducted at 50 °C with agitation. After the reaction, unreacted EDA was also removed under vacuum at 50 °C and MA was sprayed again. The percentage of poly(amidoamine) grafting onto the surface was determined to be 141% with repeated reaction cycles of eight‐times. However, the value was considerably smaller than that of the theoretical value. This indicates that the propagation of poly(amidoamine) dendron from silica surface was not achieved theoretically and hyperbranched poly(amidoamine) was grafted onto the surface because of steric hindrance of grafted polymer. In addition, the effect of initial amino group content on the growth of poly(amidoamine) from the surface was investigated. It was concluded that the method is suitable for the scale‐up synthesis of hyperbranched poly(amidoamine)‐grafted silica. Copyright © 2002 John Wiley & Sons, Ltd.     

HYDROPHILIC MODIFICATION OF PPESK POROUS MEMBRANES VIA AQUEOUS SURFACE-INITIATED ATOM TRANSFER RADICAL POLYMERIZATION

Hydrophilic surface modification of poly(phthalazinone ether sulfone ketone)(PPESK) porous membranes was achieved via surface-initiated atom transfer radical polymerization(ATRP) in aqueous medium.Prior to ATRP.chloromethyl groups were introduced onto PPESK main chains by chloromethylation.Chloromethvlated PPESK(CMPPESK) was fabricated into porous membrane through phase inversion technique.Hydrophilic poly(poly(ethylene glycol) methyl ether methacrylate)(P(PEGMA)) brushes were grafted from CMPPESK membra...     

Functionalization of nylon membranes via surface-initiated atom-transfer radical polymerization

The ability to manipulate and control the surface properties of nylons is of crucial importance to their widespread applications. In this work, surface-initiated atom-transfer radical polymerization (ATRP) is employed to tailor the functionality of the nylon membrane and pore surfaces in a well-controlled manner. A simple two-step method, involving the activation of surface amide groups with formaldehyde and the reaction of the resulting N-methylol polyamide with 2-bromoisobutyryl bromide, was first developed for the covalent immobilization of ATRP initiators on the nylon membrane and its pore surfaces. Functional polymer brushes of 2-hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol)monomethacrylate (PEGMA) were prepared via surface-initiated ATRP from the nylon membranes. A kinetics study revealed that the chain growth from the membranes was consistent with a "controlled" process. The dormant chain ends of the grafted HEMA polymer (P(HEMA)) and PEGMA polymer (P(PEGMA)) on the nylon membranes could be reactivated for the consecutive surface-initiated ATRP to produce the corresponding nylon membranes functionalized by P(HEMA)-b-P(PEGMA) and P(PEGMA)-b-P(HEMA) diblock copolymer brushes. In addition, membranes with grafted P(HEMA) and P(PEGMA) brushes exhibited good resistance to protein adsorption and fouling under continuous-flow conditions.     

Biofouling-resistance expanded poly(tetrafluoroethylene) membrane with a hydrogel-like layer of surface-immobilized poly(ethylene glycol) methacrylate for human plasma protein repulsions

In general, it is a challenge to control the highly polar material grafting from the chemically inert Teflon-based membrane surface. This work describes the surface modification and characterization of expanded poly(tetrafluoroethylene) (ePTFE) membranes grafted with poly(ethylene glycol) methacrylate (PEGMA) macromonomer via surface-activated plasma treatment and thermally induced graft copolymerization. The chemical composition and microstructure of the surface-modified ePTFE membranes were characterized by Fourier transform infrared spectroscopy (FT-IR), contact angle, and bio-atomic force microscopy (bio-AFM) measurements. Biofouling property of the modified membranes was evaluated by the measurements of the plasma protein (γ-globulin, fibrinogen, or albumin) adsorption determined using an enzyme-linked immunosorbent assay (ELISA). In general, the hydrophilicity of the surface of ePTFE membranes increases with increasing the grafting degree of the copolymerized PEGMA. The highly hydrated PEGMA chain on the resulting ePTFE membranes was found to form a surface hydrogel-like layer with regulated coverage in aqueous state, which can be controlled by the content of PEGMA macromonomer in the reaction solution. The relative protein adsorption was effectively reduced with increasing capacity of the hydration for the PEGMA chain grafted on the ePTFE membrane surface. From both results of protein adsorption and platelet adhesion test in vitro, it is concluded that the PEGMA-grafted hydrophilic ePTFE membranes could provide good biofouling resistance to substantially reduce plasma protein and blood platelet fouling on the membrane surface in human body temperature.     

Corrosion protection of iron surface modified by poly(methyl methacrylate) using surface-initiated atom transfer radical polymerization (SI-ATRP)

A new N-heterocyclic initiator N-[2-(8-heptadecenyl)-4,5-dihydro-1H-imidazole-1-ethyl]-2-bromoisobutyramide was synthesized and immobilized on the surface of iron. Methyl methacrylate was grafted from iron substrates via surface-initiated atom transfer radical polymerization (ATRP). The first-order kinetics of poly(methyl methacrylate) (PMMA) grafting from iron revealed the control of ATRP throughout the reaction, and the polymerization reached a high conversion producing polymers with good control of molecular weights (M _n?=?68,800) and low polydispersity indexes (M _w/M _n?<?1.32). The thickness of the polymer brush films was greater than 47 nm after 7 h of reaction time. The grafting density was estimated to be 0.48 chains?nm^?2. The iron surfaces at various stages of modification were characterized by scanning electron microscopy and energy dispersive spectrometer. The analytical results were consistent with a thin compact polymer coating on the surface of iron. Iron surface with grafted PMMA coating showed significant corrosion resistance. This work demonstrated that the surface-initiated ATRP is a versatile means of the surface modification of active metals with well-defined and functionalized polymer brushes.