Luminescent properties of (Y,Gd)BO3:Bi,RE (RE=Eu, Tb) phosphor under VUV/UV excitation

Bi³⁺- and RE³⁺-co-doped (Y,Gd)BO₃ phosphors were prepared and their luminescent properties under vacuum ultraviolet (VUV)/UV excitation were investigated. Strong red emission for (Y,Gd)BO₃:Bi³⁺,Eu³⁺ and strong green emission for (Y,Gd)BO₃:Bi³⁺,Tb³⁺ are observed under VUV excitation from 147 to 200 nm with a much broader excitation region than that of single Eu³⁺-doped or Tb³⁺-doped (Y,Gd)BO₃ phosphor. Strong emissions are also observed under UV excitation around 265 nm where as nearly no luminescence is observed for single Eu³⁺-doped or Tb³⁺-doped (Y,Gd)BO₃. The luminescence enhancement of Bi³⁺- and RE³⁺-co-doped (Y,Gd)BO₃ phosphors is due to energy transfer from Bi³⁺ ion to Eu³⁺ or Tb³⁺ ion not only in the VUV region but also in the UV region. Besides, host sensitization competition between Bi³⁺ and Eu³⁺ or Tb³⁺ is also observed. The investigated phosphors may be preferable for devices with a VUV light 147-200 nm as an excitation source such as PDP or mercury-free fluorescent lamp.     

Luminescence of Ce and Pr doped Sr2Mg(BO3)2 under VUV-UV and X-ray excitation

This report presents the luminescence properties of Ce³⁺ and Pr³⁺ activated Sr₂Mg(BO₃)₂ under VUV-UV and X-ray excitation. The five excitation bands of crystal field split 5d states are observed at about 46 729, 44 643, 41 667, 38 314 and 29 762 cm⁻¹ (i.e. 214, 224, 240, 261 and 336 nm) for Ce³⁺ in the host lattice. The doublet Ce³⁺ 5d→4f emission bands were found at about 25 840 and 24 096 cm⁻¹ (387 and 415 nm). The influence of doping concentration and temperature on the emission characteristics and the decay time of Ce³⁺ in Sr₂Mg(BO₃)₂ were investigated. For Pr³⁺ doped samples, the lowest 5d excitation band was observed at about 42017 cm⁻¹ (238 nm), a dominant band at around 35714 cm⁻¹ (280 nm) and two shoulder bands were seen in the emission spectra. The excitation and emission spectra of Ce³⁺ and Pr³⁺ were compared and discussed. The X-ray excited luminescence studies show that the light yields are ∼3200±230 and ∼1400±100 photons/MeV of absorbed X-ray energy for the samples Sr_1.86Ce_0.07Na_0.07Mg(BO₃)₂ and Sr_1.82Pr_0.09Na_0.09Mg(BO₃)₂ at RT, respectively.     

Characterization of the VUV excitation spectrum of BaZr(BO3)2:Eu

The excitation spectra of M (M=Si⁴⁺, Ti⁴⁺) and Eu³⁺ co-doped BaZr(BO₃)₂, BaZrO₃:Eu and La₂Zr₂O₇:Eu in the vacuum ultraviolet (VUV) regions of 110-300 nm are investigated and the host-lattice absorption are characterized. The result indicated that BaZr(BO₃)₂:Eu³⁺ phosphor has a strong absorption under the VUV excitation, and in the host-lattice excitation, the strong band at 130-160 nm could be due to the BO₃ atomic groups; the band at 160-180 nm is related to the excitation of Ba-O; 180-200 nm corresponds to the charge transfer (CT) transition of Zr-O. The band at 200-235 nm due to the CT band of Eu³⁺-O²⁻ and a bond valence study explained the observed weak CT band of Eu³⁺-O²⁻ in the excitation spectra of BaZr(BO₃)₂:Eu³⁺. The emission results show that Si⁴⁺ can sensitize luminescence in the host of BaZr(BO₃)₂:Eu but Ti⁴⁺ has no improvement effect on luminescence.     

Low temperature quenching and high efficiency Tm, La or Tb co-doped CaSc2O4:Ce phosphors for light-emitting diodes

Low temperature quenching and high efficiency CaSc₂O₄:Ce³⁺ (CSO:Ce³⁺) phosphors co-doped with Tm³⁺, La³⁺ and Tb³⁺ ions were prepared by a solid state method and the phase-forming, morphology, luminescence and application properties of these phosphors were investigated. The results showed that co-doping of Tm³⁺, La³⁺ and Tb³⁺ ions can improve the luminescence properties and decrease temperature quenching of CSO:Ce³⁺ phosphor remarkably. High efficiency green-light-emitting diodes were fabricated with the prepared phosphors and InGaN blue-emitting (∼460 nm) chips. The good performances of the green-light-emitting LEDs made from co-doped CSO:Ce³⁺ phosphors confirm the luminescence enhancement and indicate that Tm³⁺, La³⁺ and Tb³⁺ co-doped CSO:Ce³⁺ phosphors are suitable candidates for the fabrication of high efficiency white LEDs.     

VUV sensitisation of Eu emission by Tb in Ba3Tb(PO4)3-Eu

The luminescence properties of Ba₃Tb_0.9Eu_0.1(PO₄)₃ and Ba₃Gd_0.9Eu_0.1(PO₄)₃ phosphors were studied for excitation over the 120-300 nm wavelength range. It is found that Tb³⁺, which exhibits a strong vacuum-ultraviolet (VUV) absorption band, provides sensitisation of Eu³⁺ emission in this host. This effect can be used to develop phosphors with enhanced conversion efficiency of the VUV radiation into visible light.     

Luminescence in trivalent rare earth activated Sr4Al2O7 phosphor

In this paper we report the combustion synthesis of trivalent rare-earth (RE³⁺ = Dy, Eu and Ce) activated Sr₄Al₂O₇ phosphor. The prepared phosphors were characterized by the X-ray powder diffraction (XRD) and photoluminescence (PL) techniques. Photoluminescence emission peaks of Sr₄Al₂O₇:Dy³⁺ phosphor at 474 nm and 578 nm in the blue and yellow region of the spectrum. The prepared Eu³⁺ doped phosphors were excited by 395 nm then we found that the characteristics emission of europium ions at 615 nm (⁵D₀?⁷F₂) and 592 nm (⁵D₀?⁷F₁). Photoluminescence (PL) peaks situated at wavelengths of 363 and 378 nm in the UV region under excitation at around 326 nm in the Sr₄Al₂O₇:Ce³⁺ phosphor.     

Photoluminescence spectra of thenardite Na2SO4 activated with rare-earth ions, Ce, Sm, Tb, Dy and Tm

Five Na₂SO₄:RE³⁺ phosphors activated with rare-earth (RE) ions (RE³⁺=Ce³⁺, Sm³⁺, Tb³⁺, Dy³⁺ and Tm³⁺) were synthesized by heating natural thenardite Na₂SO₄ from Ai-Ding Salt Lake, Xinjiang, China with small amounts of rare-earth fluorides, CeF₃, SmF₃, TbF₃, DyF₃ and TmF₃, at 920 °C in air. The photoluminescence (PL) and optical excitation spectra of the obtained phosphors were measured at 300 and 10 K. In the PL spectrum of Na₂SO₄:Ce³⁺ at 300 K, two overlapping bands with peaks at 335 and 356 nm due to Ce³⁺ were first observed. Narrow bands observed in PL and excitation spectra of Na₂SO₄:RE³⁺ (RE³⁺=Sm³⁺, Tb³⁺, Dy³⁺ and Tm³⁺) phosphors were well identified with the electronic transitions within the 4fⁿ (n=5, 8, 9 and 12) configurations of RE³⁺. The existence of excitation bands with high luminescence efficiency at wavelengths shorter than 230 nm is characteristic of Na₂SO₄:RE³⁺ (RE³⁺=Sm³⁺, Tb³⁺, Dy³⁺ and Tm³⁺) phosphors. The obtained results suggest that these phosphors are unfavorable as the phosphor for usual fluorescence tubes, i.e., mercury discharge tubes, but may be favorable as the phosphor for UV-LED fluorescent tubes and as cathodoluminescence, X-ray luminescence and thermoluminescence phosphors.     

Synthesis and luminescent properties of nanoparticles LaSrAl3O7:Eu, Tb

Phosphors of nanoparticles LaSrAl₃O₇:RE³⁺(REEu, Tb) have been prepared by a sol–gel method. The structure and luminescent properties of LaSrAl₃O₇:Eu³⁺ and LaSrAl₃O₇:Tb³⁺ phosphors were characterized by X-ray diffraction and atomic force microscopy (AFM), photoluminescence excitation and emission spectra were utilized. From X-ray diffraction (XRD) patterns, it is indicated that the phosphor LaSrAl₃O₇ forms without impurity phase at 900 °C. From atomic force microscopy (AFM) images, it is shown that the crystal size of the phosphores are about 60–80 nm. Upon excitation with UV irradiation, it is shown that there is a strong emission at around 617 nm corresponding to the forced electric dipole ⁵D₀–⁷F₂ transition of Eu³⁺, and at around 545 nm corresponding to the ⁵D₄–⁷F₅ transition of Tb³⁺. The dependence of photoluminescence intensity on Eu³⁺(or Tb³⁺) concentration and annealing temperature were also studied in detail.     

A white light emitting phosphor Sr1.5Ca0.5SiO4:Eu, Tb, Eu for LED-based near-UV chip: Preparation, characterization and luminescent mechanism

In this work, we report preparation, characterization and luminescent mechanism of a phosphor Sr_1.5Ca_0.5SiO₄:Eu³⁺,Tb³⁺,Eu²⁺ (SCS:ETE) for white-light emitting diode (W-LED)-based near-UV chip. Co-doped rare earth cations Eu³⁺, Tb³⁺ and Eu²⁺ as aggregated luminescent centers within the orthosilicate host in a controlled manner resulted in the white-light phosphors with tunable emission properties. Under the excitation of near-UV light (394 nm), the emission spectra of these phosphors exhibited three emission bands: one broad band in the blue area, a second band with sharp lines peaked in green (about 548 nm) and the third band in the orange-red region (588-720 nm). These bands originated from Eu²⁺ 5d→4f, Tb³⁺⁵D₄→⁷F_J and Eu³⁺⁵D₀→⁷F_J transitions, respectively, with comparable intensities, which in return resulted in white light emission. With anincrease of Tb³⁺ content, both broad Eu²⁺ emission and sharp Eu³⁺ emission increase. The former may be understood by the reduction mechanism due to the charge transfer process from Eu³⁺ to Tb³⁺, whereas the latter is attributed to the energy transfer process from Eu²⁺ to Tb³⁺. Tunable white-light emission resulted from the system of SCS:ETE as a result of the competition between these two processes when the Tb³⁺ concentration varies. It was found that the nominal composition Sr_1.5Ca_0.5SiO₄:1.0%Eu³⁺, 0.07%Tb³⁺ is the optimal composition for single-phased white-light phosphor. The CIE chromaticity calculation demonstrated its potential as white LED-based near-UV chip.     

Sol-gel synthesis, structural and optical properties of rare earth ions (Sm or Dy) activated Ca3Ga2Si3O12 powder phosphors

Structural, morphological and optical properties of rare earth ions (RE³⁺=Sm³⁺ or Dy³⁺) activated Ca₃Ga₂Si₃O₁₂ (CaGaSi) phosphors synthesized by the sol-gel method are reported. XRD results confirmed the cubic phase structure of RE³⁺:CaGaSi phosphors. From the SEM images of RE³⁺:CaGaSi phosphors, it is observed that the particles are agglomerated. Photoluminescence spectra of Sm³⁺:CaGaSi phosphors have shown bright orange red emission at 598 nm (⁴G_5/2→⁶H_7/2) with an excitation wavelength of λ_exci=401 nm. In the case of Dy³⁺:CaGaSi phosphors bright yellow emission has been observed at 574 nm (⁴F_9/2→ ⁶H_13/2) with λ_exci=451 nm. From the PL spectral results, the rare earth ion concentration of CaGaSi phosphors is optimized.     

Energy transfer in Y3Al5O12:Ce, Pr and CaMoO4:Sm, Eu phosphors

Non-radiative energy transfers (ET) from Ce³⁺ to Pr³⁺ in Y₃Al₅O₁₂:Ce³⁺, Pr³⁺ and from Sm³⁺ to Eu³⁺ in CaMoO₄:Sm³⁺, Eu³⁺ are studied based on photoluminescence spectroscopy and fluorescence decay patterns. The result indicates an electric dipole-dipole interaction that governs ET in the LED phosphors. For Ce³⁺ concentration of 0.01 in YAG:Ce³⁺, Pr³⁺, the rate constant and critical distance are evaluated to be 4.5×10⁻³⁶ cm⁶ s⁻¹ and 0.81 nm, respectively. An increase in the red emission line of Pr³⁺ relative to the yellow emission band of Ce³⁺, on increasing Ce³⁺ concentration is observed. This behavior is attributed to the increase of spectral overlap integrals between Ce³⁺ emission and Pr³⁺ excitation due to the fact that the yellow band shifts to the red spectral side with increasing Ce³⁺ concentration. In CaMoO₄:Sm³⁺, Eu³⁺, Sm³⁺-Eu³⁺ transfer occurs from ⁴G_5/2 of Sm³⁺ to ⁵D₀ of Eu³⁺. The rate constant of 8.5×10⁻⁴⁰ cm⁶ s⁻¹ and the critical transfer distance of 0.89 nm are evaluated.     

Luminescent characteristics of LiCaBo3:M (M=Eu, Sm, Tb, Ce, Dy) phosphor for white LED

LiCaBO₃:M (M=Eu³⁺, Sm³⁺, Tb³⁺, Ce³⁺, Dy³⁺) phosphors were synthesized by a normal solid-state reaction using CaCO₃, H₃BO₃, Li₂CO₃, Na₂CO₃, K₂CO₃, Eu₂O₃, Sm₂O₃, Tb₄O₇, CeO₂ and Dy₂O₃ as starting materials. The emission and excitation spectra were measured by a SHIMADZU RF-540 UV spectrophotometer. And the results show that these phosphors can be excited effectively by near-ultraviolet light-emitting diodes (UVLED), and emit red, green and blue light. Consequently, these phosphors are promising phosphors for white light-emitting diodes (LEDs). Under the condition of doping charge compensation Li⁺, Na⁺ and K⁺, the luminescence intensities of these phosphors were increased.     

Photoluminescence properties of Eu in Y(PO3)3 under VUV excitation

The photoluminescence properties of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) are investigated. The excitation spectrum of Y_0.85(PO₃)₃:0.15Eu₃⁺ shows that both the (PO₃)₃³⁻ groups and the CT bands of O²⁻-Y³⁺ can efficiently absorb the excitation energy in the region of 120-250 nm. Under 147 nm excitation, the optimal emissive intensity of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) is about 36% of the commercial phosphor (Y,Gd)BO₃:Eu³⁺, which hints that the absorbed energy by the host matrix could be efficiently transferred to Eu³⁺. We try to study the concentration quenching mechanism of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) under 147 and 172 nm excitation.     

Synthesis and luminescent properties of nanoparticles GdCaAl3O7:RE (RE=Eu, Tb) via the sol-gel method

By using metal nitrates as starting materials and citric acid as complexing agent, GdCaAl₃O₇:Eu³⁺ and GdCaAl₃O₇:Tb³⁺ powder phosphors were prepared by a citrate-gel method. Thermal analysis (TG-DTG), X-ray diffraction (XRD), transmission electron microscope (TEM) and scanning electron microscope (SEM), photoluminescence excitation and emission, as well as kinetic decays were employed to characterize the resulting samples. The results of the XRD indicated the precursor samples began to crystallize at 800 °C and the crystallinity increased with elevation the annealing temperature. TEM images showed that the phosphor particles were basically of spherical shape, with good dispersion about a particle size of around 40-70 nm. Upon excitation with UV irradiation, it is shown that there is a strong emission at around 617 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺, and at around 543 nm corresponding to the ⁵D₄-⁷F₅ transition of Tb³⁺. The dependence of photoluminescence intensity on Eu³⁺ (or Tb³⁺) concentration and annealing temperature were also studied in detail.     

Luminescence characteristics of Eu3+ activated borate phosphor for white light emitting diode

In this paper, the Sr₃Y₂ (BO₃)₄:Eu³⁺ phosphor was synthesized by high temperature solid-state reaction method and the luminescence characteristics were investigated. The emission spectrum exhibits one strong red emission at 613nm corresponding to the electric dipole ⁵D₀--⁷F₂ transition of Eu³⁺ under 365nm excitation, this is because Eu³⁺ substituted for Y³⁺ occupied the non-centrosymmetric position in the crystal structure of Sr₃Y₂ (BO₃)₄. The excitation spectrum indicates that the phosphor can be effectively excited by ultraviolet (254nm, 365nm and 400nm) and blue (470nm) light. The effect of Eu³⁺ concentration on the red emission of Sr₃Y₂ (BO₃)₄:Eu³⁺ was measured, the result shows that the emission intensities increase with increasing Eu³⁺ concentration, then decrease. The Commission Internationale del'Eclairage chromaticity (x, y) of Sr₃Y₂(BO₃)₄:Eu³⁺ phosphor is (0.640,0.355) at 15 mol% Eu³⁺.     

Ionic liquid-assisted hydrothermal synthesis of dendrite-like NaY(MoO4)2:Tb phosphor

Micro-sized NaY(MoO₄)₂:Tb³⁺ phosphors with dendritic morphology was synthesized by a ionic liquid-assisted hydrothermal process. X-ray diffraction (XRD) indicated that the as-prepared product is pure tetragonal phase of NaY(MoO₄)₂. Field emission scanning electron microscopy (FE-SEM) images showed that the as-prepared NaY(MoO₄)₂:Tb³⁺ phosphors have dendritic morphology. The photoluminescent (PL) spectra displayed that the as-prepared NaY(MoO₄)₂:Tb³⁺ phosphors show a stronger green emission with main emission wavelength 545 nm corresponding to the ⁵D₄→⁷F₅ transition of Tb³⁺ ion, and the optimal Tb³⁺ doping concentration for obtaining maximum emission intensity was confirmed to be 10 mol%. Based on Van Uitert's and Dexter's models the electric dipole–dipole (D–D) interaction was confirmed to be responsible for the concentration quenching of ⁵D₄ fluorescence of Tb³⁺ in the NaY(MoO₄)₂:Tb³⁺ phosphors. The intrinsic radiative transition lifetime of ⁵D₄ level is found to be 0.703 ms.     

Eu-activated Ba2Mg(BO3)2 yellow-emitting phosphors for near ultraviolet-based light-emitting diodes

A series of Eu²⁺-activated Ba₂Mg(BO₃)₂ yellow phosphors were prepared by a high temperature solid-state reaction. The phosphor emits intense yellow light under near ultraviolet excitation. Large Stokes shift can be attributed to the asymmetric nature of the Eu site and the lack of rigidity in the host. The concentration self-quenching mechanism of Ba₂Mg(BO₃)₂:Eu²⁺ is d-d interaction and the critical transfer distance is calculated to be about 12.29 Å. Prototype light-emitting diodes were fabricated by coating the Ba₂Mg(BO₃)₂:0.07Eu²⁺ phosphor onto ∼370 nm-emitting InGaN chips. The LEDs exhibit intense yellow-emitting under a forward bias of 20 mA. The results indicate that Eu²⁺-activated Ba₂Mg(BO₃)₂ is a candidate as a yellow component for fabrication of near-UV white light-emitting diodes.     

Sol-gel growth of Gd2MoO6:Eu nanocrystalline layers on SiO2 spheres (SiO2@Gd2MoO6:Eu) and their luminescent properties

SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors were prepared by the sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectra (EDS), transmission electron microscopy (TEM), photoluminescence (PL) spectra as well as kinetic decays were used to characterize the resulting SiO₂@Gd₂MoO₆:Eu³⁺ core-shell phosphors. The XRD results demonstrate that the Gd₂MoO₆:Eu³⁺ layers on the SiO₂ spheres begin to crystallize after annealing at 600 °C and the crystallinity increases with raising the annealing temperature. The obtained core-shell phosphors have a near perfect spherical shape with narrow size distribution (average size ca. 600 nm), are not agglomerated, and have a smooth surface. The thickness of the Gd₂MoO₆:Eu³⁺ shells on the SiO₂ cores could be easily tailored by varying the number of deposition cycles (50 nm for four deposition cycles). The Eu³⁺ shows a strong PL luminescence (dominated by ⁵D₀-⁷F₂ red emission at 613 nm) under the excitation of 307 nm UV light. The PL intensity of Eu³⁺ increases with increasing the annealing temperature and the number of coating cycles.     

Effect of Eu,Tb codoping on the luminescent properties of Y2O3 nanorods

Red-emitting Y₂O₃:Eu³⁺ and green-emitting Y₂O₃:Tb³⁺ and Y₂O₃:Eu³⁺, Tb³⁺ nanorods were synthesized by hydrothermal method. Their structure and micromorphology have been analyzed by X-ray powder diffraction (XRD) and transmission electron microscopy (TEM). The photoluminescence (PL) property of Y₂O₃:Eu³⁺,Tb³⁺ phosphor was investigated. In the same host (Y₂O₃), upon excitation with ultraviolet (UV) irradiation, it is shown that there are strong emissions at around 610 and 545 nm corresponding to the forced electric dipole ⁵D₀-⁷F₂ transition of Eu³⁺ and ⁵D₄-⁷F₅ transition of Tb³⁺, respectively. Different qualities of Eu³⁺and Tb³⁺ ions are induced into the Y₂O₃ lattice. From the excitation spectrum, we speculate that there exists energy transfer from Tb³⁺ to Eu³⁺ ions .The emission color of powders reveals regular change in the separation of light emission. These powders can meet with the request of optical display material for different colors or can be potentially used as labels for biological molecules.     

Crystal structure and photoluminescence of (Y1−xCex)2Si3O3N4

Oxonitridosilicate phosphors with compositions of (Y_1−xCe_x)₂Si₃O₃N₄ (x=0−0.2) have been synthesized by solid state reaction method. The structures and photoluminescence properties have been investigated. Ce³⁺ ions have substituted for Y³⁺ ions in the lattice. The emission and excitation spectra of these phosphors show the characteristic photoluminescence spectra of Ce³⁺ ions. Based on the analyses of the diffuse reflection spectra and the PL spectra, a systematic energy diagram of Ce³⁺ ion in the forbidden band of sample with x=0.02 is given. The best doping Ce content in these phosphors is ∼2 mol%. The quenching temperature is ∼405 K for the 2 mol% Ce content sample. The luminescence decay properties were investigated. The primary studies indicate that these phosphors are potential candidates for application in three-phosphor-converted white LEDs.