Photocatalytic Activity of Microwave Plasma-Synthesized TiO2 Nanopowder

Nanocrystalline TiO₂ was synthesized using the microwave plasma technique and characterized using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, laser particle size analyzer, UV–vis spectroscopy and BET surface area analyzer. The synthesized TiO₂ powder crystallized in anatase phase and the crystallite sizes were in nanometers. The photocatalytic activity of the compound was determined and compared against the activity of the commercial Degussa P-25 TiO₂ catalyst. The degradation rates of the dyes were found to be higher over the synthesized TiO₂ as compared to that over commercial Degussa P-25 TiO₂.     

Mesoporous interstitial and substitutional nitrogen-containing titanium dioxide photocatalysts prepared by acid-assisted sol–gel procedure

Two different types of nitrogen-containing TiO₂ were synthesized via an acid-modified sol–gel method. Yellow-colored interstitial and white substitutional nitrogen-containing TiO₂ powders were characterized by means of X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller specific surface area and Barrett–Joyner–Halenda pore size distribution analyses, scanning electron microscopy, transmission electron microscopy and UV–vis absorption spectroscopy. The band gaps of interstitial and substitutional nitrogen-containing TiO₂ ceramics were estimated from UV–vis spectroscopy data to be 2.6 and 2.8 eV, respectively. Prepared substitutional nitrogen-containing TiO₂ featured steep light absorption edge with an approximately parallel characteristic to that in pure TiO₂. This fact is due to band-to-band visible light absorption ability of substitutional nitrogen-containing TiO₂. The photocatalytic properties of the produced nitrogen-containing TiO₂ samples were compared for the degradation of Direct Red 28 azo dye. Further studies were also devised to compare the catalytic efficiency of the nitrogen-containing TiO₂ powders with the pure TiO₂ synthesized via the similar sol–gel method. The produced nitrogen-containing TiO₂ samples revealed superior photocatalytic properties in comparison with pure TiO₂ due to their remarkable band gap narrowing, surface oxygen vacancies and much more surface defects. The results also revealed that the substitutional nitrogen-containing TiO₂ is the most effective photocatalyst under ultraviolet and visible light irradiation.     

In situ FT-IR studies of NO decomposition on Pt/TiO2 catalyst under UV irradiation

Photodecomposition of NO on the well-dispersed Pt/TiO₂ catalyst under UV irradiation was studied by in situ DRIFT (Diffuse-Reflectance Infrared Fourier-Transform) spectroscopy. 2 wt% Pt/TiO₂ catalyst was prepared by photochemical deposition method. The photocatalytic activity of Pt/TiO₂ is highly dependent on its pretreatment. Although the catalyst exhibited a highly adsorption capability to NO after hydrogen reduction or thermal evacuation at 500°C, no evidence upon NO decomposition was observed under UV irradiation. While reducing the catalyst at 300°C in the hydrogen flow, it not only exhibited an intense NO adsorption but also conducted a direct decomposition of NO to N₂ and O₂ under UV irradiation. The hydrogen reduction at 200°C led to a weaker NO adsorption. During UV irradiation, the IR peaks of NO fully disappeared and N₂O was formed. It is concluded that the photochemical prepared Pt/TiO₂ catalyst after activating at mild reduction conditions is highly active for NO photodecomposition. The effective oxidation states of the active components, the surface structure and the reaction mechanisms will be discussed.     

Noble metal doped graphene nanocomposites and its study of photocatalytic hydrogen evolution

This work reports the deposition of platinum (Pt) nanoparticles on the surface of graphene nanosheet by a simple approach, using a microwave-assisted method. The photocatalytic activity has been investigated for hydrogen evolution. The hydrogen evolutions were attributed to graphene, due to its high photoelectron transport properties, and the Pt nanoparticles attached on the surface of graphene sheet, which act as reaction centers for H₂ evolution. The “as-prepared” composites were characterized by Brunauer Emmett Teller (BET) surface area measurement, X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and UV–vis diffuse reflectance spectra (DRS). This work highlights the potential application of graphene-based materials in the field of energy conversion.     

Preparation and characterization of ZnTiO<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>/pillared montmorillonite composite catalyst for enhanced photocatalytic activity

ZnTiO₃–TiO₂/organic pillared montmorillonite (pMt) composite catalyst was successfully prepared in this paper by immobilizing ZnTiO₃–TiO₂ onto pMt. The composition and texture of the prepared composite catalyst were characterized by X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, transmission electron microscopy, energy dispersive spectrometry, ultraviolet–visible light (UV–Vis) diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The photocatalytic activity was tested via photocatalytic degradation of methyl blue (MB) under both visible irradiation and UV light. The results indicated that the ZnTiO₃–TiO₂/pMt composite catalyst had an apparent absorption at the area of visible irradiation, and exhibited a higher efficiency of photocatalytic degredation of MB under visible irradiation. This was due to the heterostructure of ZnTiO₃–TiO₂, and the mesoporous structure and specific surface area of the ZnTiO₃–TiO₂/pMt composite. In addition, the results of the radical scavenging experiments showed that the holes and superoxide radicals are responsible for the degradation of MB under visible irradiation.     

Sunlight-induced photocatalytic degradation of acetaminophen over efficient carbon doped TiO2 (CTiO2) nanoparticles

Carbon doped titanium oxide (CTiO₂) photocatalyst was successfully synthesized by the sol–gel method. The crystal structure, surface morphology, and optical properties of CTiO₂ have been characterized by X-ray diffraction, Brunauer–Emmett–Teller surface area (S_BET), scanning electron microscope, UV–Vis, X-ray spectroscopy (EDS), Fourier transform infrared and X-ray photoelectron spectroscopy. The photocatalytic degradation of acetaminophen (AMP) in aqueous solution, seawater, and polluted seawater has been investigated by using the synthesized photocatalyst under irradiation of UV and natural sunlight. The effectiveness of CTiO₂ compared to pure TiO₂ toward the photocatalytic removal of AMP was significantly observed. The optimized conditions including catalyst dose, initial concentration of AMP and solution pH were also studied for effective photocatalytic removal. The highest degradation rate was obtained when 2.0 g L^?1 of the catalyst was used at pH 7. The kinetic results revealed that the photocatalytic degradation of AMP using CTiO₂ obeyed a pseudo-first-order reaction kinetics.

     

Controlled crystal phase and particle size of loaded-TiO2 using clinoptilolite as support via hydrothermal method for degradation of crystal violet dye in aqueous solution

TiO₂-supported clinoptilolites (TiO₂/clinoptilolites) were successfully synthesized with controlled crystal phase and particle size via hydrothermal method to enhance photocatalytic performance of TiO₂. The effects of various parameters including temperature, acidity and concentration of Ti-containing solutions on the particle size, crystal phase and agglomeration of TiO₂ supported on clinoptilolite were investigated thoroughly by characterizations of X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscope (SEM), transmission electron microscope (TEM), BET isotherm, UV–visible (UV–vis) spectrophotometer and Malvern zetasizer. The results demonstrate that increasing temperature and strengthen acidity are beneficial to enhance the crystallinity and particle size of supported TiO₂. Increase in acidity also leads to more uniform distribution of TiO₂ on the surface of clinoptilolite. The TiO₂ nano-crystals deposited on the surface of clinoptilolite, exhibit rutile or anatase phase, strongly depending on the preparation procedure. The resultant TiO₂/clinoptilolites could be used as photo-catalysts for the degradation of crystal violet (CV) dye in aqueous solution, showing a higher photo-catalytic activity with 89% degradation within 100 min. The effect of operational parameters, such as pH values of reaction media, dose of used catalyst, and concentration of CV dye on the CV degradation performance were investigated, in which the kinetics of CV dye degradation was found to follow the pseudo-first order kinetic model.     

Microwave-hydrothermal synthesis and photocatalytic properties of biomass charcoal/TiO2 nanocomposites

Biomass charcoal-doped titanium dioxide (C/TiO₂) composites were proposed by microwave-hydrothermal and calcination method using tetrabutyl titanate as the titanium source and lignin as the carbon source. TiO₂ crystals with different morphologies could be successfully adsorbed onto the surface of biomass charcoal. These products were investigated by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TG), derivative thermogravimetric (DTG), UV–vis diffuser flection spectroscopy (UV–vis), Fourier transform infrared spectroscopy (FT-IR), and Brunauer–Emmett–Teller (BET). The photocatalytic activities of the as-obtained composites were checked under visible light irradiation. The results showed that both the microwave-hydrothermal temperature and time played an important role in the microstructure and photocatalytic activity of the samples. The rapid microwave-hydrothermal with the thermal post-treatment provides a promising route for the fabrication of biomass charcoal-doped nanocomposites materials.     

A study of photodegradation of sulforhodamine B on Au–TiO2/bentonite under UV and visible light irradiation

Au–TiO₂/bentonite samples were prepared via deposition–precipitation method and calcined at different temperatures. These samples were characterized by X-ray diffraction (XRD), UV–vis diffusion reflectance spectroscopy (DRS), BET method, X-ray photoelectron spectroscopy (XPS) and TEM. The photocatalytic activities of the samples were tested by photodegradation of sulforhodamine B (SRB) under ultraviolet (UV) and visible light irradiation. The result showed that Au–TiO₂/bentonite catalysts exhibited higher efficiency for mineralizing SRB than the well-known commercial TiO₂ photocatalyst P25 in terms of COD changes. The most important advantage of Au–TiO₂/bentonite over P25 was that it could be readily separated from aqueous suspensions by sedimentation after the reaction. It can maintain almost the same activity after being repeatedly used for 12 times. Possible mechanisms for SRB photoreaction in the presence of Au–TiO₂/bentonite were proposed in this paper.     

锐钛矿(001)与(101)晶面在光催化反应中的作用

采用水热法制备了(001)和(101)晶面暴露的单晶锐钛矿TiO₂颗粒. 利用光还原沉积贵金属(Au, Ag, Pt)和光氧化沉积金属氧化物(PbO₂, MnO_x)的方法研究了暴露的锐钛矿(001)和(101)晶面在光催化中的作用. 通过透射电子显微镜(TEM)、扫描电子显微镜(STM)、能量色散X射线光谱仪(EDX)和X射线光电子能谱(XPS)的表征, 发现发生光还原反应生成的贵金属粒子主要沉积在暴露的锐钛矿(101)晶面上, 而发生光氧化反应产生的金属氧化物颗粒主要沉积在暴露的锐钛矿(001)晶面上. 此结果表明光激发产生的电子与空穴主要并分别分布在单晶锐钛矿TiO₂的(101)与(001)晶面上, 并在其上参与光催化还原反应和氧化反应. 同时也表明暴露的不同晶面对光生电荷具有分离效应. 基于本研究可以认为同时暴露分别进行氧化和还原反应的晶面可以有效促进光催化反应.     

A new perspective for effect of S and Cu on the photocatalytic activity of S,Cu-codoped nano-TiO2 under visible light irradiation

Sulfur and copper codoped TiO₂ nanoparticles were prepared by sol-hydrothermal process. And the samples were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, Raman spectra analysis, scanning electron microscopy, Brunauer Emmett Teller analysis, UV–vis diffuse reflectance spectroscopy, X-ray photoelectron spectra and X-ray fluorescence analysis. It was found that the S, Cu-codoped TiO₂ became amorphous with the increase of Cu content, and copper on the surface of TiO₂ existed in the oxidation state of Cu(II) while S in the form of S⁶⁺ species. And the codoped particles had higher surface area, smaller particle size, stronger spectral response in visible region compared with pure TiO₂. The effects of doping amount in a wide range, catalyst dosage, and recycle on the photocatalytic activity of the codoped catalysts were investigated with Acid Orange 7 as the model compound under visible light illumination (λ > 447 nm). The results showed that S (2.0 %), Cu (5.0 %) codoped TiO₂ had the highest visible light photocatalytic activity and good reusability performance. The kinetic study showed that this photocatalytic process coincided with the Langmuir–Hinshelwood pseudo first order reaction model.     

Solvothermal preparation of copper(II) porphyrin-sensitized mesoporous TiO<Subscript>2</Subscript> composites: enhanced photocatalytic activity and stability in degradation of 4-nitrophenol

Four new copper(II) porphyrins CuPp(1, 2, 3, 4) with a different number of peripheral ester groups were synthesized and used to sensitize the mesoporous TiO₂ under solvothermal condition, and accordingly, four mesoporous CuPp(1, 2, 3, 4)/TiO₂ composites were obtained. These composites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, BET nitrogen adsorption–desorption isotherms (BET), UV–vis diffuse reflectance spectroscopy (UV–vis-DRS), and Fourier-transform infrared spectroscopy (FT-IR). The results showed the crystal structure and morphology of mesoporous TiO₂ were not affected by the porphyrin existence on its surface. The photocatalysis properties of mesoporous TiO₂ and CuPp(1, 2, 3, 4)/TiO₂ have been evaluated by conducting the photocatalytic degradation of 4-nitrophenol (4-NP) under visible-light irradiation, and the result showed their higher photocatalytic activities and the order is: CuPp(4)/TiO₂ > CuPp(3)/TiO₂ > CuPp(2)/TiO₂ > CuPp(1)/TiO₂ ? TiO₂. The probable reasons are their large surface area and different number of peripheral groups in CuPp, which separate electron–hole pairs efficiently. The repetition test of CuPp(1, 2, 3, 4)/TiO₂ composites demonstrated that they still maintained superior photocatalytic activity over six recycles.     

Hierarchical TiO2 nanosheet‐assembled nanotubes with dual electron sink functional sites for efficient photocatalytic degradation of rhodamine B

A novel Pt–TiO₂/Ag nanotube photocatalyst has been synthesized successfully via a facile method. TiO₂ nanotubes are assembled with numerous ultrathin TiO₂ nanosheets and show a highly open structure. The gaps between adjacent TiO₂ nanosheets can serve as channels for the access of reactants, accelerating the mass transfer process. During the fabrication process of the Pt–TiO₂/Ag nanotube photocatalyst, high‐quality Pt–SiO₂ nanotubes are synthesized first with the structure‐directing effect of polyvinylpyrrolidone. Then a TiO₂ layer is coated on the outside surface of the silica nanotubes. The introduced titanium species can be converted into TiO₂ nanosheet structure during the subsequent hydrothermal treatment, gradually constructing nanosheet‐assembled nanotubes. Lastly, after the introduction of another electron sink function site of Ag through UV irradiation, the Pt–TiO₂/Ag nanotube photocatalyst with dual electron sink functional sites is obtained. The specially doped Pt and Ag NPs can simultaneously inhibit the recombination process of photogenerated charge carriers and increase light utilization efficiency. Therefore, the as‐synthesized Pt–TiO₂/Ag nanotube catalyst exhibits a high photocatalytic degradation performance for rhodamine B of 0.2 min^?1, which is about 3.2 and 5.3 times as high as that of Pt–TiO₂ and TiO₂ nanotubes because of the enhanced charge carrier separation efficiency. Furthermore, in the unique nanoarchitecture, the nanotubes are assembled with numerous ultrathin TiO₂ nanosheets, which can absorb abundant active species and dye molecules for photocatalytic reaction. On the basis of experimental results, a possible rhodamine B degradation mechanism is proposed to explain the excellent photocatalytic efficiency of the Pt–TiO₂/Ag nanotube photocatalyst.     

Solvothermal synthesis of WO3/TiO2/carbon fiber composite photocatalysts for enhanced performance under sunlight illumination

Carbon fiber (CF)‐based WO₃/TiO₂ composite catalysts (WO₃/TiO₂/CF) were successfully synthesized by solvothermal method. The catalysts were characterized by XPS, SEM, BET, XRD, FTIR, Raman and UV–Vis. The analyses confirmed the WO₃/TiO₂ nanoparticles with high crystallinity deposited on the carbon structure. The photocatalytic degradation of Orange II azo dye under UV and sunlight illumination with the synthesized catalyst was explored. The composite catalyst displayed high performance (85%) for Orange II degradation while that of for WO₃/TiO₂ was found as 76%. The effects of CF amount, solution pH, initial dye concentration and catalyst dose on photocatalytic performance were studied. It was found that the degradation efficiency increased from 68% to 90% with the increasing CF amount from 3 wt% to 5 wt%, while the further increase in CF amount (7–10 wt%) decreased the photodegradation due to the blocking the active sites of WO₃/TiO₂. The enhanced photocatalytic efficiency was mainly attributed to the electrical properties of the CF and reduced bandgap.     

Enhancement of visible-light photocatalytic activity of Cu-doped TiO<Subscript>2</Subscript> nanoparticles

Bare TiO₂ and Cu-doped TiO₂ nanoparticles with different nominal doping amounts of Cu ranging from of 0.5 to 5.0 mol% were synthesized using the modified sol–gel method. The samples were physically characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller-specific surface area, UV–Vis diffuse reflectance spectroscopy, zeta potential, X-ray photoelectron spectroscopy, inductively coupled plasma, and photoluminescence techniques. The Cu-doped TiO₂ exhibited good photocatalytic activity in mineralization of oxalic acid and formic acid under visible light irradiation. Photomineralization of oxalic and formic acids under visible light irradiation revealed greatly enhanced photoactivity exhibited by the 2.0 mol% Cu-doped TiO₂ photocatalyst compared to bare TiO₂ . The enhanced photocatalytic performance arises from copper ion doping in the TiO₂ structure, leading to an extended photoresponsive range, enhanced photogenerated charge separation, and transportation efficiency.     

Elaboration of nano titania-magnetic reduced graphene oxide for degradation of tartrazine dye in aqueous solution

In this paper, magnetic nanocomposites are synthesized by loading reduced graphene oxide (RG) with two components of nanoparticles consisting of titanium dioxide (TiO₂) and magnetite (Fe₃O₄) with varying amounts. The structural and magnetic features of the prepared composite photocatalysts were investigated by powder X-ray diffraction (XRD), Fourier transform infrared spectra (FT-IR), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectra (UV–vis/DRS), Raman and vibrating sample magnetometer (VSM). The resulting TiO₂/magnetite reduced graphene oxide (MRGT) composite demonstrated intrinsic visible light photocatalytic activity, on degradation of tartrazine (TZ) dye from a synthetic aqueous solution. Specifically, it exhibits higher photocatalytic activity than magnetite reduced graphene oxide (MRG) and TiO₂ nanoparticles. The photocatalytic degradation of TZ dye when using MRG and TiO₂ for 3 h under visible light was 35% and 10% respectively, whereas for MRGT it was more than 95%. The higher photocatalytic efficiency of MRGT is due to the existence of reduced graphene oxide and magnetite which enhances the photocatalytic efficiency of the composite in visible light towards the degradation of harmful soluble azo dye (tartrazine).     

3D flower-like heterostructured TiO2@Ni(OH)2 microspheres for solar photocatalytic hydrogen production

TiO₂@Ni(OH)₂ core-shell microspheres were synthesized by a facile strategy to obtain a perfect 3D flower-like nanostructure with well-arranged Ni(OH)₂ nanoflakes on the surfaces of TiO₂ microspheres; this arrangement led to a six-fold enhancement in photocatalytic hydrogen evolution. The unique p-n type heterostructure not only promotes the separation and transfer of photogenerated charge carriers significantly, but also offers more active sites for photocatalytic hydrogen production. A photocatalytic mechanism is proposed based on the results of electrochemical measurements and X-ray photoelectron spectroscopy.     

Microstructure and hydrogen production activity of Pt–TiO2 prepared by precipitation–photodeposition

A series of Pt–TiO₂ photocatalysts were prepared by a facile precipitation–photoreduction method under different pH conditions, using H₂PtCl₆ as platinum precursor. The microstructure and chemical state of Pt loaded on the surface of TiO₂ were analyzed by X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). It was revealed that the size and distribution of Pt nanoparticles on TiO₂ surface is closely related to the initial pH of H₂PtCl₆ solution. The optimal pH value for forming highly dispersed Pt nanoparticles is 12. The photocatalytic activities of the prepared samples were investigated in terms of hydrogen production. The results indicated that the Pt–TiO₂ sample prepared by precipitation–photodeposition method shows much higher activity than that prepared by traditional photodeposition method.     

Synthesis and photocatalytic properties of core–shell TiO~2@ZnIn_2S_4 photocatalyst

A novel core–shell TiO2@ZnIn2S4composite has been synthesized successfully by a simple and flexible hydrothermal route using TiO2as precursors.The as-synthesized samples were characterized by X-ray diffraction,UV–vis diffuse reflectance spectra and transmission electron microscopy.The photocatalytic properties of samples were tested by degradation of aqueous methylene blue（MB）under visible light irradiation.It was found that the as-synthesized TiO2@ZnIn2S4photocatalyst was more effcient than TiO2and ZnIn2S4in the photocatalytic degradation of MB.Moreover,TEM images confrmed the TiO2@ZnIn2S4nanoparticles possessed a well-proportioned core–shell morphology.     

Facile one-pot hydrothermal synthesis of B/N-codoped TiO2 hollow spheres with enhanced visible-light photocatalytic activity and photoelectrochemical property

B/N-codoped TiO₂ hollow spheres (B/N-THs) were synthesized by facile one-pot hydrothermal method. The prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM), N₂ adsorption-desorption isotherms, UV–vis diffuse reflectance spectrum (DRS) and X-ray photoelectron spectroscopy (XPS). The B/N-THs have large surface areas (up to 172.1 m² g⁻¹). The photocatalytic activities of as-prepared THs were evaluated by degradation of Reactive Brilliant Red dye X-3B solution under visible light irradiation. The results showed that B/N-THs exhibited the highest photocatalytic activity due to their high surface area and synergetic effect of B/N-codoped. A photocurrent–time spectrum was examined by anodic photocurrent response to characterize the electron-transferring efficiency in the process of photocatalysis reaction.