Co掺杂对TiO2光催化剂结构与性能的影响

采用溶胶-凝胶法制备了Co掺杂的TiO2粉末, 利用透射电子显微镜、X射线光电子能谱、紫外可见光谱和X射线衍射技术对粉末进行了表征, 并利用环形光催化反应器对其光催化活性进行了测试. 结果表明, 随焙烧温度的增加, Co/TiO2粉末的晶粒尺寸逐渐增大, 升至873 K时, 钴元素以CoTiO3形式从TiO2中析出, 同时TiO2由锐钛矿型向金红石型发生转变, 相转变过程中晶格常数a和c以及晶胞体积发生收缩. 掺杂钴以后, 粉末的光谱吸收范围被拓展至可见光, 但是其光催化活性却明显降低.     

Fe掺杂对纳米TiO2薄膜的结构与光催化性能的影响

采用溶胶-凝胶法制备了Fe掺杂的TiO2薄膜,利用X射线光电子能谱、X射线衍射技术、显微共聚焦拉曼光谱、紫外可见光谱和原子力显微镜等对薄膜进行表征,以甲基橙为反应模型对光催化活性进行测试。 结果表明,在300~600 ℃焙烧时,TiO2以锐钛矿结构存在,700 ℃焙烧时出现金红石结构。 随掺铁量和焙烧温度的增加,Fe/TiO2薄膜的表面粗糙度和晶粒尺寸均逐渐增大;随镀膜层数的增加,Fe/TiO2薄膜光谱吸收向可见光方向移动;较低含量的铁掺杂改善了TiO2薄膜的光催化活性,而较高含量的铁掺杂则使TiO2薄膜的光催化活性下降,掺铁量为0.1%时Fe/TiO2薄膜的光催化活性最好。     

超临界乙醇干燥法制备高热稳定性Fe-TiO2

以TiCl4和Fe(NO3)3为前体,采用共沉淀法和乙醇超临界干燥技术合成了具有不同Fe3 掺杂量的TiO2,样品织构性质用XRD、TEM、BET、TG和UV-vis等技术表征.研究结果表明,超临界干燥方法可以有效地提高Fe-TiO2样品的热稳定性,样品在500℃焙烧时Fe3 对TiO2的比表面积、晶粒度、晶相等性质影响不大,即使在800℃焙烧还能保持锐钛矿晶型.但Fe3 在掺杂量小于0.5at%时,Fe3 会与TiO2晶格中的Ti4 发生同晶取代,从而使TiO2的锐钛矿晶胞参数和晶胞体积增大,导致晶格应力和表面张力增加;当Fe3 掺杂量大于0.5at%时,Fe3 以氧化物形式在TiO2表面聚集,在800℃热处理中晶粒更易被烧结增大;漫反射UV-vis光谱表征发现,Fe3 掺杂提高了样品对可见光的吸收,随着Fe3 含量和焙烧温度的提高,样品对可见光的吸收也随着增加.但是Fe3 掺杂降低了锐钛矿TiO2在紫外光下降解甲基橙速率,这表明锐钛矿TiO2的光催化活性与样品的晶格缺陷和颗粒尺寸密切相关.     

可见光响应的氯掺杂TiO2的制备、表征及其光催化活性

 采用HCl水解钛酸四丁酯制备了可见光响应的氯掺杂TiO2光催化剂,并用X射线衍射线、透射电子显微镜、 X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱等测试手段对其结构进行了表征. 结果表明,氯元素的引入降低了无定形相向锐钛矿转变以及锐钛矿向金红石相转变的温度. 300 ℃焙烧的氯掺杂TiO2吸收波长拓展到可见光区,且XPS证实氯元素以阴离子形式存在于TiO2晶格中. 苯酚降解实验表明, 在大于400 nm的可见光照射下, 300 ℃焙烧的氯掺杂TiO2具有最佳的光催化活性, 120 min时苯酚的降解率达到42.5%.     

纳米TiO_2催化剂微晶结构对光催化反应的影响

采用正交试验方法,调控Ti（SO4）2原料浓度、沉淀剂NH4HCO3浓度、沉淀pH值、焙烧温度和焙烧时间等制备条件制备得到了25个锐钛矿相TiO2光催化剂.对TiO2光催化降解十二烷基苯磺酸钠（SDBS）的催化活性与TiO2锐钛矿相10个晶面的法向粒子尺寸、晶格畸变应力、X射线衍射强度之间的关系进行了分析.发现TiO2光催化SDBS的降解遵循一级反应动力学;其主要影响因素为（101）晶面结晶情况,而与其余晶面的相关性不大;光催化反应需要晶格畸变较少的结晶较完整的（101）晶面;晶粒尺寸减小,比表面积增大有利于提高反应速率;光催化反应过程主要在结晶的锐钛矿相（101）晶面表面上发生,而无定形TiO2催化活性较低.     

硼硫共掺杂TiO2的光催化性能及掺杂机理

采用水热法制备了硼硫共掺杂的TiO2光催化剂(TiO2-B-S),并用其光催化降解甲基橙.结果表明,在240℃下水热反应12h时制得的TiO2-B-S具有较高的催化活性,紫外光照射50min和太阳光照射230min时对甲基橙的降解率分别达99.8%和81%.X射线粉末衍射、紫外-可见漫反射光谱和X射线光电子能谱等研究表明,TiO2-B-S为锐钛矿晶型,硫硼掺杂能抑制TiO2粒径的生长;TiO2-B-S同时具有较高的紫外光和可见光活性的原因可能是掺杂的硼以B3 进入晶格中,导致TiO2晶格畸变,带隙变窄.掺杂的硼和硫还提高了TiO2的表面酸度和对可见光的吸收.     

TiO2/蒙脱石纳米复合物中TiO2的结构相变

以钛酸丁酯和季铵盐改性有机蒙脱石为原料,采用原位水解法和原位脱羟法制备了TiO2/蒙脱石纳米复合物。采用X射线衍射(XRD)、拉曼光谱(Raman)表征了不同焙烧温度下TiO2/蒙脱石纳米复合物中TiO2的结构相变,并与不同焙烧温度下纯TiO2的结构相变进行对比。结果发现TiO2/蒙脱石纳米复合物中TiO2从锐钛矿相开始转变为金红石的最低温度要比纯TiO2从锐钛矿开始相转变为金红石的最低温度高200℃,且在焙烧温度1 200℃时还存在锐钛矿相,而纯TiO2在焙烧温度800℃时就全部转换为金红石相。TiO2/蒙脱石纳米复合物中TiO2和纯TiO2的平均晶粒度都随焙烧温度升高而增大,但TiO2/蒙脱石纳米复合物中TiO2的平均晶粒度要小于相同温度下焙烧纯TiO2的平均晶粒度。表明蒙脱石结构层的硅氧结构抑制了TiO2晶型由锐钛矿相向金红石相的转变,进而使相变温度升高,同时阻碍了晶体的生长。     

低温苯甲醇醇解法制备高活性锐钛矿型纳米晶TiO2光催化剂

 以TiCl4 为钛源,采用低温苯甲醇醇解法制备了不同粒径及晶相组成的大表面TiO2纳米晶,利用X射线衍射、热重-差热分析、透射电子显微镜、拉曼光谱、紫外-可见漫反射光谱和N2物理吸附等方法考察了焙烧温度和焙烧时间对其晶相组成、晶粒尺寸、比表面积及孔体积等微结构性质的影响,并以苯酚的光催化降解为模型反应评价了样品的光催化活性. 结果表明,未经任何热处理的TiO2样品即为锐钛矿晶相,控制焙烧温度及焙烧时间可进一步调控样品的粒径、比表面积、晶相结构及表面氧缺位浓度. 经400 ℃焙烧3 h制备的纳米晶TiO2具有最佳的光催化活性,其活性比商用Degussa P-25 TiO2更高.     

酸催化水解法制备可见光响应N掺杂纳米TiO2催化剂

 以TiCl4为钛源,采用酸催化水解法合成了TiO2前驱体,在NH3/N2气氛中经程序升温处理制得不同N掺杂量的TiO2可见光响应催化剂. 以苯酚为模型物,考察了催化剂在可见光及紫外光区的催化活性. 采用X射线衍射、紫外-可见漫反射光谱、傅里叶变换红外光谱、扫描电镜和低温氮物理吸附对光催化剂的晶相结构、光谱特征和表面结构进行了表征. 结果表明,掺杂N后锐钛矿TiO2的可见光催化活性显著提高,在500 ℃焙烧5 h制得的催化剂在可见光区及紫外光区均表现出最高的光催化活性. N掺杂对TiO2的晶粒大小、比表面积和晶相结构影响不大. 适量N掺杂可在TiO2表面形成Ti-O-N键,形成了新的能级结构,使催化剂的吸收带边红移至490～550 nm; 同时该结构也可有效提高TiO2的紫外光催化活性.     

BiVO4/TiO2复合光催化剂的制备及可见光降解腐殖酸

首先以P123为模板剂利用溶胶-凝胶法制备TiO2载体,然后采用沉淀法制得介孔BiVO4/TiO2复合光催化剂.采用X射线衍射仪、漫反射吸收光谱仪、比表面分析仪对所制得的光催化剂进行了表征.结果表明,催化剂样品中的TiO2主要以锐钛矿型存在,BiVO4为四方相和单斜相共存的混晶,与单纯的BiVO4、TiO2光催化剂相比,BiVO4/TiO2复合光催化剂具有更高的可见光吸收性能、较好的比表面积和均一的介孔结构.腐殖酸的可见光降解试验表明,随着腐殖酸初始浓度的增大,其光降解率逐渐降低,ln(C/C0)对t呈线性关系.试验同步研究了腐殖酸光催化降解过程中荧光光谱、红外光谱和GC-MS谱图的变化情况.     

Photochemical preparation of poly(N-vinyl-2-pyrrolidone)-stabilized platinum colloids and their deposition on titanium dioxide

Preparation processes for Pt-deposited TiO(2) (Pt/TiO(2)) by the synthesis of Pt nanoparticles and their deposition were pursued by transmission electron microscopy, extended X-ray absorption fine structure, UV-vis spectroscopy, and Fourier transform infrared spectroscopic studies. Colloidal dispersions of Pt particles stabilized by poly(N-vinyl-2-pyrrolidone) (PVP) were photochemically synthesized in aqueous ethanol solution. The average diameter of Pt particles was estimated to be 2.0 +/- 0.5 nm, which was almost unchanged by changing the reducing agent from ethanol to methanol and 2-propanol. The PVP-stabilized Pt particles were distributed over a TiO(2) surface only by mixing the Pt colloidal dispersions and TiO(2). CO was chemically coordinated on the Pt particles on a TiO(2) surface after heat treatment was carried out in an O(2) flow at 673 K to completely remove the residual PVP on Pt/TiO(2). Hydrogen reduction at 473 K did not increase the amount of CO adsorbed on Pt sites. The Pt/TiO(2) catalyst after the oxidation treatment showed higher activity for CO photooxidation than that obtained for pure TiO(2) catalyst. The CO photooxidation rate was not unchanged by the H(2) reduction.     

Dispersion and Structure Studies of Molybdenum Oxide on Anatase TiO2

X-ray photoelectron spectroscopy (XPS) and extended X-ray absorption fine structure (EXAFS) were used to characterize the structure of the mixture of molybdenum oxide and anatase calcined at 723 K. The resuits indicate that molybdenum oxide can disperse onto the surface of anatase (TiO2) and the dispersion threshold is 11.2 mg in per gram of MoO3 or 4.8 Mo atoms/nm^2 TiO2. When the coment of MoO3 is below the dispersion threshold, MoO3 species is in highly dispersed state interacting strongly with TiO2 support and in discrete tetrahedral coordination. [MoO4], on the surface of TiO2. When the MoO3 loading is above this value, MoO3 exists in both dispersed phase and crystalline phase. MoO3 in dispersed phase is still a discrete [MoO4] tetrahedron; MoO3 in crystal phase is in octahedral coordination.     

Effect of calcination temperature on the structure of a Pt/TiO2 (B) nanofiber and its photocatalytic activity in generating H2

Hydrogen trititanate (H 2Ti 3O 7) nanofibers were prepared by a hydrothermal method in 10 M NaOH at 403 K, followed by acidic rinsing and drying at 383 K. Calcining H 2Ti 3O 7 nanofibers at 573 K led to the formation of TiO 2 (B) nanofibers. Calcination at 673 K improved the crystallinity of the TiO 2 (B) nanofibers and did not cause any change in the morphology and dimensions of the nanofibers. TiO 2 (B) and H 2Ti 3O 7 nanofibers are 10-20 nm in diameter and several micrometers long, but FE-SEM reveals that several of these nanofibers tend to bind tightly to each other, forming a fiber bundle. Calcination at 773 K transformed TiO 2 (B) nanofibers into a TiO 2 (B)/anatase bicrystalline mixture with their fibrous morphology remaining intact. Upon increasing the calcination temperature to 873 K, most of the TiO 2 (B) nanofibers were converted into anatase nanofibers and small anatase particles with smoother surfaces. In the photocatalytic dehydrogenation of neat ethanol, 1% Pt/TiO 2 (B) nanofiber calcined at 673 K was the most active catalyst and generated about the same amount of H 2 as did 1% Pt/P-25. TPR indicated that the calcination of 1% Pt/TiO 2 (B) nanofiber at 573 K produced a poor Pt dispersion and poor activity. Calcination at a temperature higher than 773 K (in ambient air) resulted in an SMSI effect similar to that observed over TiO 2 in the reductive atmosphere. As suggested by XPS, such an SMSI effect decreased the surface concentration of Pt metal and created Pt (delta) sites, preventing Pt particles from functioning as a Schottky barrier and leading to a lower activity. Because of the synergetic effect between TiO 2 (B) and anatase phases, the bicrystalline mixture, produced by calcining at 773 K, was able to counter negative effects such as the reduction in surface area and the SMSI effect and maintained its photocatalytic activity.     

Intracrystalline structure and physicochemical properties of mixed SiO2-TiO2 sol-pillared aluminosilicate

Highly porous layered inorganic-inorganic nanohybrids were prepared by pillaring SiO2-TiO2 nanosol particles with aluminosilicate layers. According to powder X-ray diffraction analysis, the basal spacing of SiO2-TiO2 pillared aluminosilicate (STPC) calcined at 400 degrees C was determined to be larger than 40 A. N2 adsorption-desorption isotherm measurements showed the STPC to have a large Brunauer-Emmett-Teller surface area of approximately 590 m2/g, of which approximately 70% originates from micropores with a size range of 8-16 A. The sorption behavior of various solvent vapors such as hexane, methanol, and water reveals internal pore surfaces of the STPC to be hydrophobic. A distinct blue shift of absorption edge in UV-vis spectra clearly demonstrates that the nanosized TiO2 particles are formed between silicate layers as a pillar. Fourier transform infrared and extended X-ray absorption fine structure analysis at the Ti K edge reveals that the pillared titania exists in the form of anatase-structured TiO2 nanocrystals, not in the form of covalently bonded mixed particles of TiO2-SiO2. On the basis of the present findings, we are able to conclude that the quantum-sized TiO2 and SiO2 particles are independently intercalated to form a multilayer stacking intracrystalline structure in the gallery space of aluminosilicate clay.     

Photocatalytic Degradation of Acetaldehyde on Mesoporous TiO2: E?ects of Surface Area and Crystallinity on the Photocatalytic Activity

"Mesoporous TiO2 powder and films with worm-like channels were synthesized by an evaporation-induced self-assembly approach. The as-prepared samples were calcined at different temperature to investigate the effect of calcined temperature on the mesostructure and the photocatalytic activity. Acetaldehyde photodegradation in gas phase was employed to evaluate the photocatalytic activity of mesoporous TiO2. Results showed that all the calcined powder samples exhibited higher photocatalytic activities than that of Degussa P25. The sample calcined at 400 oC, which showed higher activity than other samples, possessed a homogeneous pore diameter of about 6.0 nm and an 11.0 nm crystalline anatase pore wall, as well as large surface area of 117 m2/g. It was speculated that two factors of surface area and crystallinity affected the photocatalytic activity of mesoporous TiO2 photocatalyst. The mesoporous TiO2 films fabricated by spin-coating also had high photocatalytic activities."     

Effects of calcium ions on solubility and aggregation behavior of an anionic sulfonate gemini surfactant in aqueous solutions

In this work, a ternary composite, Pt/TiO(2)/RGO (reduced graphite oxide), was prepared via immobilizing Pt particles onto the TiO(2)/RGO composite that was obtained via redox reaction of TiCl(3) and GO. The composite was characterized by different techniques including X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy. The TiO(2) particles with size less than 10 nm were uniformly distributed throughout the RGO, and almost each Pt particle with size around 3 nm adhered to TiO(2) particles, resulting in high dispersion of all Pt particles on the support. The Pt particles were in the electron-deficient state due to the strong interactions with the TiO(2) particles and the RGO support. The catalytic performance of the composite for nitrobenzene hydrogenation was investigated under solvent-free condition. It was indicated that the Pt/TiO(2)/RGO catalyst exhibited high activity with a turnover frequency (e.g., 59,000 h(-1)) as well as superior selectivity to aniline (e.g., >99%). Moreover, the catalyst can be reused for six times without any activity loss, which resulted from the stable structure of the catalyst.     

预处理条件对Pt/Al2O3催化还原NO的活性影响

用溶胶-凝胶法制备Al2O3载体,浸渍法制备质量分数为0.5%的Pt/Al2O3催化剂.研究焙烧气氛和温度对选择性催化还原NO反应活性和Pt价态的影响.结果表明,H2焙烧的活性温度区间最宽,随着焙烧温度的升高,温度区间变化很小,523K下O2焙烧的催化剂活性最好,且活性区间向高温方向移动.活性现象用程序升温脱附实验(NO-TPD,NO-O2-TPD)进行了解释.XPS研究表明,523K下O2用焙烧Pt的主要价态是Pt2+,而523K下H2和N2焙烧Pt的主要价态为Pt0.     

乙苯氧化脱氢反应Fex/TiO2的催化性能研究

新型氧化钛负载铁催化剂Fex/TiO2在低温乙苯空气氧化脱氢制苯乙烯反应中具有良好的催化活性。350 ℃,使用Fe7/TiO2催化剂,当Fe的质量分数为7%时,可获得14.6%乙苯单程转化率和99.0%的苯乙烯选择性。通过X衍射、表面吸附、热分析及扫描电镜仪器分析表征,考察氧化钛负载铁催化剂在乙苯低温氧化脱氢反应中的催化作用。350 ℃乙苯可被活化,催化剂活性的高低取决于活性物种Fe(III)的分布状态和质量分数。     

球磨法制备复合光催化剂Bi12TiO20/ZnO及其光催化性能

本文用水作为分散介质,采用球磨法掺杂一定量的Bi₁₂TiO₂₀于ZnO中制备复合光催化剂Bi₁₂TiO₂₀/ZnO. 利用UV-Vis、XRD和SEM等仪器对样品进行了分析与表征. 通过对甲基橙的氧化来研究其光催化活性. 结果表明,光催化剂Bi₁₂TiO₂₀/ZnO对甲基橙氧化的催化活性高于氧化锌的催化活性.当Bi₁₂TiO₂₀的掺杂量为0.5%(质量分数),球磨时间为12 h,焙烧温度为300℃时,光照20 min后,复合光催化剂Bi₁₂TiO₂₀/ZnO对甲基橙的降解率可达到95.2%.