Preparation of nanocrystalline Fe-doped TiO<Subscript>2</Subscript> powders as a visible-light-responsive photocatalyst

Nanocrystalline Fe-doped TiO₂ powders were prepared using TiOSO₄, urea, and Fe(NO₃)₃ · 9H₂O as precursors through a hydrothermal method. The as-synthesized yellowish-colored powders are composed of anatase TiO₂, identified by X-ray diffraction (XRD). The grain size ranged from 9.7 to 12.1 nm, calculated by Scherrer’s method. The specific surface area ranged from 141 to 170 m²/g, obtained by the Brunauer–Emmett–Teller (BET) method. The transmission electron microscopy (TEM) micrograph of the sample shows that the diameter of the grains is uniformly distributed at about 10 nm, which is consistent with that calculated by Scherrer’s method. Fe³⁺ and Fe²⁺ have been detected on the surface of TiO₂ powders by X-ray photoelectron spectroscopy (XPS). The UV–Vis diffuse reflection spectra indicate that the light absorption thresholds of the Fe-doped TiO₂ powders have been red-shifted into the visible light region. The photocatalytic activity of the Fe-doped TiO₂ was evaluated through the degradation of methylene blue (MB) under visible light irradiation. The Fe-doped TiO₂ powders have shown good visible-light photocatalytic activities and the maximum degradation ratio is achieved within 4.5 h.     

N,B, Si-tridoped mesoporous TiO<Subscript>2</Subscript> with high surface area and excellent visible-light photocatalytic activity

N, B, Si-tridoped mesoporous TiO₂, together with N-doped, N, B-codoped and N, Si-codoped TiO₂, was prepared by a modified sol–gel method. The samples were characterized by wide-angle X-ray diffraction (WAXRD), N₂ adsorption–desorption, transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, UV–visible adsorbance spectra (UV–vis) and X-ray photoelectron spectra (XPS). The N, B, Si-tridoped mesoporous TiO₂ showed small crystallite size, large specific surface area (350 m²/g), uniform pore distribution (3.2 nm) and strong absorption in the visible light region. The photocatalytic activities of the samples were evaluated by the photodegradation of 2,4-dichlorophenol (2,4-DCP) aqueous solution. The N, B, Si-tridoping sample exhibited much higher photocatalytic activity compared with other synthesized photocatalysts. The high activity could be attributed to the strong absorption in the visible light region, large specific surface area, small crystallite size, large amount of surface hydroxyl groups, and mesoporosity.     

Influence of NH<Subscript>3</Subscript>-treating temperature on visible light photocatalytic activity of N-doped P<Subscript>25</Subscript>-TiO<Subscript>2</Subscript>

The influence of NH₃-treating temperature on the visible light photocatalytic activity of N-doped P₂₅-TiO₂ as well as the relationship between the surface composition structure of TiO₂ and its visible light photocatalytic activity were investigated. The results showed that N-doped P₂₅-TiO₂ treated at 600°C had the highest activity. The structure of P₂₅-TiO₂ was converted from anatase to rutile at 700°C. Moreover, no N-doping was detected at the surface of P₂₅-TiO₂. There was no simply linear relationship between the visible light photocatalytic activity and the concentration of doped nitrogen, and visible light absorption. The visible light photocatalytic activity of N-doped P₂₅-TiO₂ was mainly influenced by the synergistic action of the following factors: (i) the formation of the single-electron-trapped oxygen vacancies (denoted as V_o^·); (ii) the doped nitrogen on the surface of TiO₂; (iii) the anatase TiO₂ structure.     

Photocatalysis enhancement of CaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>, Nd<Superscript>3+</Superscript>@TiO<Subscript>2</Subscript> composite powders

CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were synthesized by a sol–gel method under mild conditions (i.e. low temperature and ambient pressure). The as-prepared powders were characterized by transmission electron microscopy (TEM) and analyzed by X-ray diffraction (XRD). The photocatalytic behavior of the TiO₂-base surfaces was evaluated by the degradation of nitrogen monoxide gas. It suggested that CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders were composed of anatase titania and that CaAl₂O₄:Eu²⁺, Nd³⁺. TiO₂ particles were deposited on the surface of CaAl₂O₄:Eu²⁺, Nd³⁺ to form uniform film. CaAl₂O₄:Eu²⁺, Nd³⁺@TiO₂ composite powders exhibited higher photocatalytic activity compared with pure TiO₂ under visible light. And the result also clearly indicated that the long afterglow phosphor absorbed and stored lights for the TiO₂ to remain photocatalytic activity in the dark.     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.     

Nitrogen-doped TiO<Subscript>2</Subscript> nanopowders prepared by chemical vapor synthesis: band structure and photocatalytic activity under visible light

During chemical vapor synthesis of TiO₂ nanopowders, nitrogen atoms were doped into the crystal lattice of TiO₂. The nitrogen atoms were predominantly incorporated substitutionally in the crystal lattice of TiO₂ nanopowders up to the doping level of 1.25 mol% nitrogen, whereas they were in both interstitial and substitutional sites over about 1.43 mol% nitrogen. From the photocatalytic activity of nitrogen-doped TiO₂ estimated by decomposition of methylene blue under visible light, it was found that the substitutional nitrogen anions appearing at the low level doping was beneficial to its photocatalytic activity, whereas the interstitial ones appearing at the high level doping over 1.25 mol% nitrogen were not. The improved photocatalytic activity due to the substitutionally doped nitrogen was attributed to band gap narrowing which was confirmed by the studies of XPS, near edge X-ray absorption fine structure, and UV–Vis absorption.     

Preparation,characterization and enhanced photocatalytic activity of Ni<Superscript>2+</Superscript> doped titania under solar light

Anatase TiO₂ was prepared by sol-gel method through the hydrolysis of TiCl₄. Ni²⁺ was doped into the TiO₂ matrix in the concentration range of 0.02 to 0.1 at.% and characterized by various analytical techniques. Powder X-ray diffraction revealed only anatase phase for all the samples, while diffuse reflectance spectral studies indicated a red shift in the band gap absorption to the visible region. The photocatalytic activities of these photocatalysts were probed for the degradation of methyl orange under natural solar light. The photocatalyst with optimum doping of 0.08 at.% Ni²⁺, showed enhanced activity, which is attributed to: (i) effective separation of charge carriers and (ii) large red shift in the band gap to visible region. The influence of crystallite size and dopant concentration on the charge carrier trapping — recombination dynamics is investigated.     

Hydrothermal synthesis of (Fe,N) co-doped TiO<Subscript>2</Subscript> powders and their photocatalytic properties under visible light irradiation

(Fe, N) co-doped titanium dioxide powders have been prepared by a quick, low-temperature hydrothermal method using TiOSO₄, CO(NH₂)₂, Fe(NO₃)₃, and CN₃H₅ · HCl as starting materials. The synthesized powders were characterized by XRD, TEM, BET, XPS, and UV–Vis spectroscopy. Experimental results show that the as-synthesized TiO₂ powders are present as the anatase phase and that the N and Fe ions have been doped into the TiO₂ lattice. The specific surface area of the powders is 167.8 m²/g by the BET method and the mean grain size is about 11 nm, calculated by Scherrer’s formula. UV–Vis absorption spectra show that the edge of the photon absorption has been red-shifted up to 605 nm. The doped titanium dioxide powders had excellent photocatalytic activity during the process of photo-degradation of formaldehyde and some TVOC gases under visible light irradiation.     

Chemical synthesis of Ni/TiO<Subscript>2</Subscript> nanophotocatalyst for UV/visible light assisted degradation of organic dye in aqueous solution

The Ni/TiO₂ nanoparticles with different Ni dopant content were prepared by a modified sol–gel method. The structure and photoinduced charge properties of the as-prepared catalysts were determined using X-ray diffraction, transmission electron microscopy, UV–vis diffuse reflectance spectroscopy and surface photovoltage spectroscopy techniques, and the photocatalytic efficiency of these catalysts was tested using an organic dye. It was shown that Ni modification could greatly enhance the photocatalytic efficiency of these nanocomposite catalysts by taking the photodegradation of methyl orange as a model reaction. With appropriate ratio of Ni and TiO₂, Ni/TiO₂ nanocomposites showed the superior photocatalytic activity than the single TiO₂ nanoparticles. Surface photovoltage spectra demonstrated that Ni modification could effectively inhibit the recombination of the photoinduced electron and holes of TiO₂. This electron–hole pair separation conditions are responsible for the higher photocatalytic performance of Ni/TiO₂ nanocomposites in the visible region of electromagnetic spectrum.     

Electrospinning fabrication of mesoporous nano Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-TiO<Subscript>2</Subscript>@activated carbon fiber membrane for hybrid removal of phenol from waste water

A mesoporous iron–titanium mixed-oxides@activated carbon(AC) fiber membrane was fabricated by an electrospinning method and applied to the treatment of phenol waste water. The physical and chemical properties of the composite fiber membrane were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption, UV–Vis light diffuse reflectance spectroscopy (DRS), Raman spectroscopy, respectively. The results indicate that the composite nanofiber membrane is composed of α-Fe₂O₃, anatase TiO₂ and activated carbon phases with a specific surface area of 231 m² g^–1 and narrow pore size distribution of 3–6 nm. DRS reveals that the composite membrane has high photons absorption from both ultraviolet light and visible light irradiation owing to the combination of Fe₂O₃, TiO₂ and carbon. The prepared nano Fe₂O₃–TiO₂@AC fiber membrane can act as an efficient reusable photocatalyst and adsorbent for 100% remo val of phenol pollutant. This hybrid technique is hopeful to be widely used in the treatment of various organic waste waters.     

Catalytic Properties of TiO<Subscript>2</Subscript>/Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> Nanoparticles in Plasma Chemical Treatment

We proposed here a new process coupling dielectric barrier discharge (DBD) plasma with magnetic photocatalytic material nanoparticles for improving yield in DBD degradation of methyl orange (MO). TiO₂ doped Fe₃O₄ (TiO₂/Fe₃O₄) was prepared by the sol-gel method and used as a new type of magnetic photocatalyst in DBD system. It was found that the introduction of TiO₂/Fe₃O₄ in DBD system could effectively make use of the energy generated in DBD process and improve hydroxyl radical contributed by the main surface Fenton reaction, photocatalytic reaction and catalytic decomposition of dissolved ozone. Most part of MO (88%) was degraded during 30 min at peak voltage of 13 kV and TiO₂/Fe₃O₄ load of 100 mg/L, with a rate constant of 0.0731 min^?1 and a degradation yield of 7.23 g/(kW h). The coupled system showed higher degradation efficiency for MO removal.     

Hydrothermal synthesis and characterization of In<Superscript>3+</Superscript> modified BiVO<Subscript>4</Subscript> nanoparticles with enhanced photocatalytic activity

In³⁺-doped BiVO₄ nanoparticles with enhanced visible light activity have been successfully synthesized by a hydrothermal method. The synthesized materials were characterized by X-ray diffraction, Raman, X-ray photoelectron spectroscopy, scanning electron microscopy, BET surface areas analysis, and ultraviolet–visible diffuse reflectance spectra. In comparison with pure BiVO₄, the In³⁺-doped BiVO₄ displayed greater photocatalytic activity in the degradation of methyl blue under visible light illumination. All samples possessed a single monoclinic structure. The introduction of In ions resulted in structural distortion and the decreased band gap energy, producing more electrons and holes for photocatalytic reaction. In the meantime, the doping In ions entails a red shift in the absorption edge and an increase in the intensity of light absorption. The best photocatalytic performance was obtained with the BiVO₄ sample containing 5.0 mol% In ions.     

Opposite effect of Li<Superscript>+</Superscript> codoping on the upconversion emissions of Er<Superscript>3+</Superscript>-doped TiO<Subscript>2</Subscript> powders

The Er³⁺-Li⁺ codoped TiO₂ powders have been prepared by the non-aqueous sol–gel method. The green and red upconversion emissions centered at about 526, 550 and 663 nm were observed by the ²H_11/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 transitions of Er³⁺, respectively. Li⁺ codoping has opposite effect on the upconversion emissions intensities for Er³⁺-doped TiO₂ at sintering temperatures of 1,073 and 1,273 K. At 1,073 K, the Er³⁺-doped TiO₂ phase transition from anatase to rutile was accelerated with increasing Li⁺ codoping concentration, leading to the increase of crystal field symmetry of Er³⁺, thus the upconversion emissions intensities decreased. At 1,273 K, Li⁺ codoping had no effect on the phase structure of Er³⁺-doped TiO₂ and only increased the Er–O bond length, it indicated that the upconversion emissions intensities greatly enhanced because of the decrease of crystal field symmetry of Er³⁺.     

TiO<Subscript>2</Subscript>/WO<Subscript>3</Subscript> photoanodes with enhanced photocatalytic activity for air treatment in a polymer electrolyte cell

The application of electrochemically enhanced photocatalysis in air treatment using a Nafion-based photoelectrochemical cell and TiO₂/WO₃ photoanodes for organic vapor photooxidation under both UV and visible light irradiation is briefly presented. In that direction, the obtained results regarding the preparation and characterization of the TiO₂/WO₃ photoanodes with enhanced photocatalytic activity are reviewed. Particular emphasis is given in the comparison of the photocatalytic behavior of bilayer TiO₂/WO₃ coatings, electrosynthesized on stainless steel mesh and powder C + mixed (WO₃ + TiO₂) photoanodes. The advantages of using a high surface area C + mixed (WO₃ + TiO₂) powder catalysts as photoanodes against their plain TiO₂ + C and WO₃ + C analogues are discussed.     

Ion engineering techniques for the preparation of the highly effective TiO<Subscript>2</Subscript> photocatalysts operating under visible light irradiation

The successful application of ion engineering techniques for the development of TiO₂ photocatalysts operating under visible and/or solar light irradiations has been summarized in this review article. First, we have physically doped various transition metal ions within a TiO₂ lattice on an atomic level by using an advanced metal ion implantation method. The metal ion implanted TiO₂ could efficiently work as a photocatalyst under visible light irradiation. Some field tests under solar light irradiation clearly revealed that the Cr or V ions implanted TiO₂ samples showed 2–3 times higher photocatalytic reactivity than the un-implanted TiO₂. Second, we have developed the visible light responsive TiO₂ thin film photocatalyst by a single process using an RF-magnetron sputtering (RF-MS) deposition method. The vis-type TiO₂ thin films showed high photocatalytic reactivity for various reactions such as reduction of NOx, degradation of organic compounds, and splitting of H₂O under visible and/or solar light irradiations.     

Vacuum activation-induced Ti<Superscript>3+</Superscript> and carbon co-doped TiO<Subscript>2</Subscript> with enhanced solar light photo-catalytic activity

Ti³⁺ and carbon co-doped TiO₂ photocatalysts were prepared hydrothermally to introduce the carbon, and followed by simple vacuum activation to achieve the Ti³⁺ self-doping. The prepared co-doped photocatalysts were characterized by XRD, TEM, UV–Vis absorption spectra, EPR, and XPS. It was found that the co-doped TiO₂ has dispersed nanoparticles and a narrower band-gap compared with the un-doped TiO₂ and single-doped TiO₂. The experimental results displayed that the coke carbon generated on the surface of co-doped TiO₂ acts as a photosensitizer and has the photosensitization effect under solar light irradiation. Except for the carbon sensitization effect, the Ti³⁺ self-doping modification has a synergistic effect which is the reason for the effective photo-degradation of methyl orange under simulated solar light irradiation.     

F and Fe co-doped TiO2 with enhanced visible light photocatalytic activity

Four different sols, pure TiO₂, F doped TiO₂, Fe doped TiO₂, and F–Fe co-doped TiO₂ sols, were prepared by peroxidation at low temperature. The crystal structure, morphology, light adsorption, and photocatalytic properties of the pure and doped TiO₂ were examined by X-ray diffraction, transmission electron microscopy, and ultraviolet–visible spectrophotometry. The relationship between the average size, crystal type, range of visible light absorption, and photocatalytic activity and content and type of doped ions were investigated. The results showed that the average size of the F–Fe co-doped TiO₂ composed of both the anatase and rutile phases was the same as that of pure TiO₂. Furthermore, the visible light photocatalytic activity of the F–Fe co-doped TiO₂ was significantly improved over pure TiO₂, F-doped TiO₂, and Fe-doped TiO₂ due to the large red shift in the light adsorption edge.     

Photocatalytic degradation of methylene blue on Fe3+-doped TiO2 nanoparticles under visible light irradiation

Fe³⁺-doped TiO₂ composite nanoparticles with different doping amounts were successfully synthesized using sol-gel method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and ultravioletvisible spectroscopy (UV-Vis) diffuse reflectance spectra (DRS). The photocatalytic degradation of methylene blue was used as a model reaction to evaluate the photocatalytic activity of Fe³⁺/TiO₂ nanoparticles under visible light irradiation. The influence of doping amount of Fe³⁺ (ω: 0.00%–3.00%) on photocatalytic activities of TiO₂ was investigated. Results show that the size of Fe³⁺/TiO₂ particles decreases with the increase of the amount of Fe³⁺ and their absorption spectra are broaden and absorption intensities are also increased. Doping Fe³⁺ can control the conversion of TiO₂ from anatase to rutile. The doping amount of Fe³⁺ remarkably affects the activity of the catalyst, and the optimum efficiency occurs at about the doping amount of 0.3%. The appropriate doping of Fe³⁺ can markedly increase the catalytic activity of TiO₂ under visible light irradiation. __________ Translated from Journal of Northwest Normal University (Natural Science), 2006, 42(6): 55–56 [译自: 西北师范大学学报(自然科学版)]     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

Photocatalytic activity of (sulfur,nitrogen)-codoped mesoporous TiO<Subscript>2</Subscript> thin films

Nitrogen and sulfur co-doped mesoporous TiO₂ thin films were fabricated using thiourea as a doping resource by the combination of the sol–gel and evaporation-induced self-assembly (EISA) processes. Scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), N₂ adsorption–desorption, and UV–vis spectra were performed to characterize the as-synthesized mesoporous TiO₂ materials. The XPS result shows that O–Ti–N and O–Ti–S bonds in the (S, N)-codoped mesoporous TiO₂ were formed. The resultant mesoporous (S, N)-codoped TiO₂ exhibited anatase framework with a high porosity and a narrow pore distribution. After being illuminated for 3 h, methyl orange (MO) could be degraded completely by the co-doped sample under the ultraviolet irradiation, whereas mesoporous TiO₂ film without doping could only degrade 60% MO. After being illuminated by visible light, the water contact angles of the mesoporous co-doped TiO₂ samples decreased slightly, but the pure TiO₂ mesoporous film exhibited no change in the hydrophilicity.