Ce掺杂TiO2纳米粉体的制备及其光催化性能研究

以钛酸丁酯为前驱体,冰醋酸为螫合剂,以硝酸铈为掺杂剂,采用溶胶.凝胶法制备了铈掺杂TiO2纳米粉体.研究了铈掺杂对TiO2相组成和晶粒尺寸的影响及不同掺杂量对TiO2光催化活性的影响,确定了Ce的最佳掺杂量.结果表明:Ce掺杂缩小了TiO2的锐钛矿相→金红石相(A→R)的相变温区范围,抑制了TiO2的晶粒增长.热处理温度升高,二氧化钛的比表面积下降.掺杂适量的铈提高了TiO2的光催化活性,Ce掺杂为0.05;摩尔分数时Ce-TiO2的光催化活性达到最佳,甲基橙降解率可达90;左右.     

水热处理温度对WO3微晶晶相、形貌和光催化性能的影响

以Na2WO4·2H2O和盐酸为原料,采用水热法合成了WO3微晶.通过X射线衍射分析(XRD)、电子扫描显微镜(SEM)、热重-差示扫描量热法(TG-DSC)等表征手段,研究了水热反应温度及煅烧处理对产物的晶体结构和微观形貌的影响.结果表明:水热处理温度从100℃升到160℃时,所得微晶的衍射峰强度逐渐升高,所得样品的结晶度趋于完整,其形貌由片状结构变为自组装的球状结构.光催化结果表明可知随着水热温度的升高,光催化性能先上升后下降,产物的结晶性与其比表面积大小为影响其光催化性能的主要因素.通过对比煅烧前后产物的光催化性能发现六方相WO3结构比正交相WO3·0.33H2O结构具有更好的光催化活性.     

Ag/Bi2S3/Bi2WO6复合催化剂合成及光催化性能研究

以硝酸铋、钨酸钠和硫脲为起始原料,采用一步水热法成功合成Bi2 S3/Bi2 WO6光催化剂,采用光还原法在Bi2S3/Bi2 WO6表面沉积贵金属Ag.采用XRD、XPS、FESEM、TEM和UV-Vis-DRS等手段对Bi2S3/Bi2WO6和Ag/Bi2S3/Bi2WO6进行表征,并以罗丹明B和苯酚作为模型污染物对其光催化性能进行研究.结果证明,耦合Bi2S3可以提高Bi2WO6催化剂的光催化活性,Ag沉积使得其光催化性能进一步提高,且Ag的沉积量与催化剂的活性关系密切,其中5; Ag/Bi2S3/Bi2WO6的光催化效果最好.此外,结合活性物种检测和能带结构分析,对Ag/Bi2S3/Bi2WO6的光催化活性增强机理进行了分析.     

ZnWO4-ZnO复合光催化剂的制备及光催化性能

以ZnO及WO3为前驱反应物,制备了一系列不同ZnWO4含量的ZnWO4-ZnO复合光催化剂.利用X射线衍射、扫描电子显微镜及X射线能谱仪等手段对催化剂进行表征,并以紫外光为光源,罗丹明B为模拟污染物,评价催化剂的活性.结果表明,热处理温度及ZnWO4与ZnO摩尔比对催化剂光催化降解罗丹明B的活性影响显著.当复合4mol;ZnWO4,并于850 ℃煅烧所制得的ZnWO4-ZnO催化剂活性最高,比纯ZnO高出25;.这是因为ZnWO4的复合可抑制ZnO晶粒长大,提高光生电子与空穴的分离效率,进而改善其光催化活性.     

WO3的水热合成及其与CuCrO2复合后的光催化产氢性能

以H40N41W12·xH2O为钨源,硫酸为酸化剂,通过水热法合成前驱体,经一定的热处理后制得单斜晶系WO3,再将WO3与p型半导体物质CuCrO2复合后得到的WO3-CuCrO2复合催化剂用于光催化分解纯水产氢的实验.通过对所得WO3样品的X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外可见漫反射(UV-Vis-DR)光谱分析及光催化活性测试,分别考察了硫酸用量、硫酸铵等量替代硫酸及后期热处理过程对制得WO3的形貌、尺寸及光催化性能的影响.结果表明:当硫酸用量为6.8 mmol且硫酸铵等量替代2.7 mmol硫酸时得到的WO3性能较优,其粒径较小,分散较为均匀,以其制得的WO3-CuCrO2复合催化剂光催化产氢活性较高,后期热处理过程对WO3样品晶型、形貌、吸收光的性能及复合样品WO3-CuCrO2的光催化性能有很大的影响.     

N掺杂石墨烯/WO3纳米线复合光催化剂的光催化活性研究

采用两步水热法制备了N掺杂石墨烯/WO3纳米线复合光催化剂,用XRD、TEM、FT-IR和XPS等技术对样品进行了表征,考察了该催化剂在模拟太阳光下光催化降解甲基橙溶液活性.结果表明,经过两次水热反应,WO3纳米线负载在N掺杂石墨烯表面.引入N掺杂石墨烯有助于减少光生电子空穴对的复合,光催化活性显著提高.模拟太阳光照60 min,该复合光催化剂对甲基橙的脱色率达到99.4;.     

三维Ag2O/WO3复合催化剂的制备及光催化性能研究

WO3是一种带隙约为2.7 eV的过渡金属半导体,可见光就能激发其光催化活性,这极大地提高了太阳光的利用率,但纯WO3纳米材料催化活性偏低,针对这一难题,本文选取了三维网格结构的WO3纳米材料为载体,利用化学搅拌法制备了不同摩尔比的Ag2O/WO3复合光催化剂.选择亚甲基蓝为研究对象,测定了不同摩尔比的Ag2O/WO3复合催化剂的光催化性能.实验表明,当Ag2O和WO3的摩尔配比为1∶2时,该复合催化剂的光催性能最好.过量的Ag2O纳米颗粒会增加Ag2O/WO3内部电子空穴的复合几率,反而导致光催化剂反应活性的降低.     

稀土离子Er3+掺杂Bi2WO6的第一性原理计算及可见光催化性能研究

采用溶剂热法合成了稀土离子Er3+掺杂Bi2WO6光催化剂.采用密度泛函理论(DFT)研究了Er3+掺杂Bi2WO6的晶体结构和电子结构.DFT计算结果表明,Er3+掺杂后在价带顶形成了Er杂质能级,Bi2WO6的带隙减小,有利于光生电子的生成和光生载流子的复合.实验结果表明,Er3+掺杂量对Bi2WO6的显微形貌影响不大.掺杂Er3+后,Bi2WO6的光催化性能得到显著提高,当掺杂4;摩尔比的Er3+时,产品的光催化性能最好,可见光照射150分钟后,可降解91.5;的罗丹明B,较未掺杂Bi2WO6的光催化性能提高了83;.     

不同晶相WO3的热分解法制备及其光催化性能

以钨酸铵为钨源,硝酸为沉淀剂,首先通过沉淀法制备前驱体H2 WO4,随后采用热分解H2 WO4法合成六方及单斜晶相WO3催化剂.利用X射线衍射(XRD)、拉曼光谱、差热-热重(TG-DTA)、扫描电子显微镜(SEM)、X射线光电子能谱(XPS)及紫外-可见漫反射光谱(UV-Vis DRS)对H2 WO4向WO3转变过程中结构、形貌、组成及光学性质的变化进行研究.结果表明,热处理后前驱体发生如下相变过程:H2 WO4→六方相WO3→六方/单斜相WO3→单斜相WO3.此外,以罗丹明B为模拟污染物,考察不同晶相WO3的光催化活性,结果表明,六方相WO3具有更高的光催化性能,单斜相WO3的活性较低.     

水热合成Cu-Bi2WO6及其光催化性能研究

以Bi(NO3)3·5H2O和Na2WO4·2H2O为原料,NaOH为矿化剂,CuCl2和CuSO4为铜源水热法离子掺杂合成Bi2WO6粉体,并使用XRD、SEM、UV-VIS、XPS对其进行表征,分析了不同铜源离子掺杂Bi2WO6以及掺杂量对所制备样品光催化性能的影响.结果表明,以CuCl2为铜源离子掺杂Bi2WO6的样品粒径减小,吸收边红移.掺杂后的铜以中Cu2和Cu+两种电子形式存在.光催化测试结果表明,以CuCl2为铜源且掺入量为1.5mol;时所制备的Bi2WO6样品的光催化活性最高.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

First-principles coexistence simulations of supercooled liquid silicon

We perform first-principles coexistence simulations of the low-density and the high-density phases of supercooled liquid silicon and find a negative slope for the coexisting line in the temperature-pressure plane. Electron density maps and electron-localization function plots of the two phases of silicon show marked differences. The calculated differences suggest more localized electrons in the low-density liquid compared to the high-density liquid, coming from an increased population of covalent bonds, which further explain the calculated negative slope in the two phase coexistence regime. This is consistent with the presence of a pseudo-gap in low-density liquid silicon, absent in the high-density liquid which shows a metallic behavior.     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

Crystal structures of thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane

Structures of both thecis andtrans isomers of dithiahexahydro[3.3]metacyclophane, ?C₆H₄?CH₂SCH₂?C₆H₁₀?CH₂SCH₂?, have been determined, wherecis andtrans refer to the attachments to the cyclohexane ring. Thecis form crystallizes in the monoclinic space groupP2₁/c witha=8.4299(11)Å,b=21.772(2)Å,c=8.9724(13)Å, β=116.574(11)^o, andZ=4. Thetrans isomer packs into the monoclinic space groupP2₁ witha=8.159(16)Å,b=10.185(5)Å,c=9.558(2)Å, β=112.435(18)^o, andZ=2. The cyclohexane ring of thecis isomer is in the chair conformation, while the cyclohexane of thetrans isomer is found in a twisted boat conformation.     

CTAB与SDBS对碳酸锶粒子生长形态调控及机理研究

以表面活性剂CTAB和SDBS为化学添加剂,采用化学共沉淀法对碳酸锶晶体的生长形态进行调控,成功地制备出了实心的树枝状和花瓣为空心的花状碳酸锶粉体,并用X射线衍射(XRD)、扫描电子显微镜(SEM)和傅里叶变换红外光谱(FT-IR)等分析手段对样品进行了表征;最后重点对化学添加剂可能产生的影响机理进行了初步的探讨.结果表明,CTAB和SDBS在晶体生长的过程中能起到显著的影响作用,两者对粒子分散性能的作用效果相反,而且后者对晶体(013)和(213)晶面表面能降低的贡献明显大于前者.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.