DPE对正丁基锂及聚苯乙烯活性种缔合体的影响

以具有较大空间位阻的1,1-二苯基乙烯(DPE)作为盖帽剂,使用核磁锂谱研究了正丁基锂(n-BuLi)经其盖帽以后缔合态的变化。结果表明:DPE的加入使n-BuLi中的超大缔合体解缔合成六元缔合体,但是不会影响原有的六元缔合体。由1,1-二苯基己基锂引发的苯乙烯本体聚合实验中存在转化率突变点。在突变点前的聚合产物中存在超分子结构,并随着聚合反应的进行逐渐解缔合;突变点过后超分子结构解缔合完全,反应加速进行。     

苯乙烯阴离子本体聚合引发剂缔合及其机理的研究

分别以正丁基锂和叔丁基锂为引发剂,采用自制管式流动反应装置,对较高温度下苯乙烯阴离子本体聚合动力学进行了研究.证实了正丁基锂主要以六元缔合结构形式引发聚合,并导致超分子团聚体的形成,从而使进一步的聚合因单体扩散受阻而受到限制,并伴随聚合转化率停滞平台（SCP）的产生.随后由于前期聚合累积的能量,使超分子结构完全解离.聚合温度越高,SCP持续时间越短.结果还表明,在正丁基锂引发剂中,存在一个以六元缔合结构为基础形成的更大的缔合体结构.原子力显微镜照片显示,超分子结构的直径分别为20～30nm和50～60nm.此外,在阴离子聚合过程中活性种的缔合结构只决定于初始引发剂的分子结构,而不同活性种缔合结构对阴离子聚合的链增长存在很大影响,从而解释了采用不同结构的锂系引发剂引发苯乙烯单体聚合时聚合速率存在巨大差异的原因.     

苯乙烯阴离子高温本体聚合引发机理的新发现(二)

采用创建的一种研究方法,以正丁基锂(n-BuLi)为引发剂,研究了苯乙烯(St)在60℃至140℃下的阴离子本体聚合.结果表明,低温下(＜20℃)以六元缔合结构形式存在的非活性正丁基锂在高温下(≥60℃)会转化为活性种.随机分布在该六元结构上的平均1.3个离子对可以引发St的阴离子聚合.然而从六元缔合结构上增长出的超分...     

P-配合物对异戊二烯负离子聚合中3,4结构影响的研究

在四氢呋喃(THF)与环己烷的混合溶剂中,以正丁基锂(n-BuLi)为引发剂,选取P配合物(Pcomplex)为调节剂,实现了异戊二烯(Ip)的负离子可控聚合,得到了高3,4结构率的聚异戊二烯(PI)(78.76%).采用1H-NMR对聚合物的结构进行了表征和分析.证实了由n-BuLi引发的负离子聚合,单体插入离子对之间参与聚合的速率及聚合结构取决于正负离子对之间的尺度,该尺度与单体插入所需求的尺度相当时,插入聚合速率最快,最容易.对Ip而言,单体插入离子对之间聚合形成3,4-PI时需求的尺度最小.Pcomplex由于其同时含有与Li+同源的锂原子以及空间位阻较大的苯、萘、蒽等基团,可通过改变活性种正负离子对之间的通道尺度,有效地促进3,4聚合反应,抑制1,2和1,4聚合反应,因而有效提高了PI 3,4结构率,使得Ip的聚合变得可控.相反,升高温度可以增加正负离子对之间的尺度,使得3,4聚合结构含量减少,1,4聚合结构含量增加,但温度越高,反式含量越多.     

ε-己内酯负离子聚合过程烷氧基锂活性种的缔合

本文以粘度法研究在苯溶剂中,ε-己内酯负离子开环聚合过程,增长链活性种烷氧基锂(—O~-Li~+)的缔合,发现己内酯活性种的缔合和一般非极性单体不同,前者在聚合过程中(单体消耗完以前)并不发生缔合。在单体消耗完以后,聚己内酯活性种才确实以缔合体的形式存在。这是由于内酯本身贡献了强的溶剂化作用。     

离子缔合性试剂在萃取分离-定量分析中的应用(续)

5.2 支配离子缔合体萃取性的因素支配离子缔合体萃取性的因素主要是(1)离子周围的水结构;(2)离子以及缔合物的亲油性;(3)离子的形状;(4)在有机相中的缔合体的离解反应、聚集反应等。(1)离子周围的水结构为了使离子缔合体萃取性良好,首先必须使水溶液中的缔合性良好。即有必要用WSP性或WSB性强     

醇钾及酚钾在甲基丙烯酸甲酯阴离子聚合中的应用

以正丁基锂(n-BuLi)为引发剂,叔丁醇钾(t-BuOK)和苯酚钾(POK)为副反应抑制剂,实现了甲基丙烯酸甲酯(MMA)在四氢呋喃(THF)溶剂中的阴离子聚合。采用凝胶渗透色谱(GPC)、核磁共振氢谱(1 H-NMR)等研究了产物的数均分子量、分子量分布(MWD)和分子结构。结果表明:t-BuOK与n-BuLi之间发生反离子交换反应使活性中心的反离子Li~+被K~+替换,从而在一定程度上抑制了MMA聚合过程中的副反应,当n(t-BuOK)/n(n-BuLi)≥10时,可在0℃下实现MMA的可控阴离子聚合;PMMA分子量分布较窄(1.22),且数均分子量与设计值十分接近,MMA聚合的副反应得到了有效控制;进一步添加的POK能与活性中心的K~+配合,促进对MMA聚合副反应的抑制,使MMA的可控阴离子聚合能在较高温度(40℃)下得以实现,所合成的聚甲基丙烯酸甲酯(PMMA)数均分子量分布窄(1.24)且数均分子量符合设计值。     

十二烷基苯磺酸钡存在下负离子聚合控制聚苯乙烯立构规整性研究

以正丁基锂(n-BuLi)为引发剂,环已烷为溶剂,通过添加十二烷基苯磺酸钡/四氢呋喃(SDBB/THF),对苯乙烯负离子聚合进行了研究.该体系可在60℃聚合得到立构规整性聚苯乙烯,其丁酮不溶物含量可达80%左右.13C-NMR表征结果显示其微观序列组成以等规结构为主,三元组mm和等规五元组mmmm含量可达57%和45%;DSC谱图中不仅有聚苯乙烯玻璃化温度(100℃),而且在211℃有一熔融峰.GPC结果表明,实测分子量与设计分子量差别较大,且分子量分布较宽。     

丁二烯阴离子聚合动力学及活性种的研究

本文对于n-BuLi/2G引发的丁二烯阴离子聚合动力学数据及产物微观结构进行了解析。建立了动力学模型,提出了聚合反应机理。求得了单量体、一络合体和二络合体的增长速度常数和诸活性种之间的平衡常数以及它们对形成乙烯基结构的贡献。     

聚醚树枝体线性聚(N-异丙基丙烯酰胺)不对称嵌段共聚物的 合成及自组装

采用原子转移聚合方法合成了聚N-异丙基丙烯酰胺和聚醚树技体的不对嵌段共聚物Dendr.PE-PNI-PAM。实验结果表明Dendr.PE-PNIPAM分子在水中能通过疏水缔合作用形成具有双分子膜结构的超分子聚集体。临界缔合浓度(CAC)、聚集体的大小及形貌对树枝体的代数具有明显的依赖关系。该聚集体对温度刺激具有响应性,并在人体体温温度(37.5℃)发生相转变。在高于相转变温度时,Dendr.PE-PNIPAM分子形成管状、带状等多重形态的超级结构的聚集体。     

A New View of the Initiation and Propagation in Anionic Polymerization

This work confirms the new view of the initiation and propagation mechanism of the anionic polymerization previously proposed, based on the investigation of anionic bulk‐polymerization of styrene and α‐methyl styrene with the help of a self designed microflow device and characterized by GPC and in situ ⁷Li NMR. It was found that n‐BuLi tended to form the hexameric‐aggregated structure and even to form the huge aggregated structure based on the former. These aggregations of initiators could directly initiate the anionic polymerization and form the supramolecule aggregations. The supramolecule aggregations inevitably blocked the diffusion of the monomers to the ion‐pairs and resulted in a stationary‐conversion platform. Then the aggregators were dissociated completely into equal binary‐aggregated species, and the polymerization continued again rapidly before the termination. Tetrahydrofuran (THF) acted as the electron donator, which could push the electron cloud to Li cation and make the aggregated ring of the active species rather loosened and facilitated the monomer to insert in. Therefore, a little THF can greatly promote the anionic polymerization. However, further addition of THF might block the channel between the ion‐pairs and decrease the propagation rate. It was also found that the aggregated structure of the active species during the anionic polymerization only depends on the initiator aggregations which were formed before the polymerization.     

Synthesis of α-Bromine- Terminated Polystyrene Macroinitiator and Its Initiation of MMA Polymerization by ATRP

In the present paper the synthesis of block copolymers via the transformation from living anionic polymerization (LAP) to atom transfer radical polymerization (ATRP) was described. Α-Bromine-terminated polystyrenes(PStBr) in the LAP step was prepared by using n-BuLi as initiator, tetrahydrofuran (THF) as the activator, α-methylstyrene (α-MeSt) as the capping group and liquid bromine (Br2) as the bromating agent. The effects of reaction conditions such as the amounts of α-MeSt, THF, and Br2 as well as molecular weight of polystyrene on the bromating efficiency (BE) and coupling extent (CE) were examined. The present results show that the yield of PStBr obtained was more than 93.8% and the coupling reaction was substantially absent. PStBr was further used as the macroinitiator in the polymerization of methyl-methacrylate(MMA) in the presence of copper(Ⅰ) halogen and 2,2-bipyridine(bpy) complexes. It was found that the molecular weight of the resulted PSt-b-PMMA increased linearly with the increase of the conversion of MMA and the polydispersity was 1.2-1.6. The structures of PStBr and P(St-b-MMA) were characterized by 1H NMR spectra.     

Anionic Polymerization of Z,Z-2,4Hexadienedinitrile

Abstract

Z,Z-2,4-Hexadienedinitrile, synthesized by the oxidative cleavage of o-phenylenediamine, was found to undergo anionic polymerization with n-BuLi in DMF at room temperature or below. The polymerization behavior appears to be similar to that of acrylonitrile polymerization using n-BuLi as initiator. Infrared and NMR analysis of the polymer indicate the presence of both 1,4 and 1,2 linkages, with the latter predominating.     

A study of the polymerization of styrene initiated by K-THF-GIC system

In this paper, the polymerization of styrene initiated by potassium (K)-tetrahydrofuran (THF)-graphite intercalation compound (GIC) (K-THF-GIC) was studied. The mechanism of the polymerization was determined to be anionic polymerization according to its characteristics. The effect of the concentration of the initiator and monomer was studied. It was found that the polymerization mainly occurred on the surface and edge of the intercalated graphite. It was also shown that the polarity of solvent has little effect on the polymerization yield in this system.     

Anionic polymerization of 2,2,5,5-tetramethyl-1-oxa-2,5-disilacyclopentane

In the first of a two-part series, a study has been made of the anionic polymerization of a five-membered cyclocarbosiloxane, 2,2,5,5-tetramethyl-1-oxa-2,5-disilacyclopentane. The polymerization was initiated by lithium n-butyldiphenylsilanolate in the presence of tetrahydrofuran. The chemical shifts of the protons of the cyclic monomer and the polymer were found to be different, and therefore the rate of polymerization was obtained in an NMR spectrometer. The effects of varying the concentrations of THF, initiator, and water upon the rate of polymerization and upon the molecular weight and the molecular weight distribution were investigated. At a constant concentration of monomer and initiator, the rate of polymerization increased when the THF concentration was increased. At a constant concentration of monomer and THF the rate of polymerization reached a constant value when the initiator concentration was varied. The molecular weight and the molecular weight distribution were dependent upon the initiator to water ratio, whereas water concentration had little effect on the rate of polymerization. Essentially monodispersed polymers were obtained when the concentration of initiator was in large excess to that of water or vice versa. A bimodal distribution in molecular weight was obtained when the concentration of initiator was approximately equal to that of water. The apparent activation energy of polymerization was 12.7 kcal/mole.     

丁二烯－八甲基环四硅氧烷的嵌段共聚合研究 Ⅰ．嵌段共聚物合成及D_4开环动力学

以α－甲基萘钾为引发剂，按顺序加入丁二烯、八甲基环四硅氧烷（Ｄ４）在ＴＨＦ中进行负离子嵌段共聚，制备了聚了二烯－聚二甲基硅氧烷嵌段共聚物．讨论了聚合条件对嵌段共聚合过程的影响．考察了聚了二烯活性链引发Ｄ４进行嵌段共聚的反应动力学，求得在ＴＨＦ中３０℃时Ｄ４开环链增长的表观速率为１０ｋｇ／ｍｏｌ．ｈ、表观活化能为２８．３ｋＪ／ｍｏｌ．     

ATRP法合成结构对称的双羧基聚苯乙烯及其超分子的形成

从二甲苯出发,经过溴甲基化反应、氧化反应、酯化反应和溴代反应,合成了一种四官能团的引发剂,4,6-二(溴甲基)-1,3-苯二甲酸二甲酯.用该引发剂引发苯乙烯进行原子转移自由基聚合,实验结果表明聚合反应具有活性自由基聚合的特征.通过苯乙烯的本体聚合反应获得了分子量可控、双酯基位于聚合物链中间的聚苯乙烯.经过水解反应,使聚合物中的双酯基被水解成双羧基,从而得到了结构对称的两亲性聚合物,双羧基聚苯乙烯.利用该聚合物具有分子识别的特性,与十二烷胺形成了离子键超分子化合物.此工作为超分子星形聚合物的设计合成提供了简便快捷的方法.     

Anionic polymerization of methacrylonitrile—I. Polymerization with n-butyllithium as initiator

The anionic polymerization of methacrylonitrile has been studied at ?75° in toluene and with n-butyllithium as initiator. The kinetics of the polymerization were investigated considering the consumption of both monomer and initiator. BuLi disappears relatively slowly and about 50–60% remains unreacted. A simple kinetic scheme cannot therefore be put forward. All possible side reactions have also been examined. The molecular weight study establishes the living character of this system and gives an initiator efficiency of about 0.2. The contribution of low molecular weight products, typical of the polymerization of polar monomers, is also taken into account. In order to obtain a better understanding of the mechanism of this polymerization, in which unreacted initiator is probably engaged in very stable and inactive mixed associated particles, small amounts of THF (known frequently to break down such aggregates) were added to the system. A rather unexpected slow but complete disappearance of the initiator occurs; the conversion at which the rate of monomer consumption levels off depends on the THF concentration.     

Anionic polymerization of acrylates. II. Polymerization of 2-ethylhexyl acrylate initiated by butyllithium/lithium-tert-butoxide system in tetrahydrofuran and its mixtures with toluene

The anionic polymerization of 2-ethylhexyl acrylate (EtHA) initiated with the complex butyllithium/lithium-tert-butoxide (BuLi/t-BuOLi) was investigated at ?60°C in a medium of various solvating power, i.e., in mixtures of toluene and tetrahydrofuran and in neat tetrahydrofuran. With increasing amount of THF in the mixture the attainable limiting conversion of polymerization decreases; the monomer can be polymerized quantitatively only in a toluene/THF mixture (9/1). Molecular weights of the polymers thus obtained, their distribution, and initiator efficiency are not appreciably affected by the polymerization medium. The molecular weight distribution of the products is medium-broad (M_w/M_n = 2–2.4), with a hint of bimodality. The ¹H-¹³C-NMR, and IR spectra suggest that during the polymerization there is neither any perceptible reesterification of the polymer with the alkoxide nor transmetalation of the monomer with the initiator. In a suitable medium, autotermination of propagation proceeds to a limited extent only, predominantly via intramolecular cyclization of propagating chains; in a medium with a higher content of polar THF, it prevails and terminates propagation before the polymerization of the monomer has been completed. © 1992 John Wiley & Sons, Inc.