Preparation of Activated Carbon Functional Ceramics From Coal Pitch

The influences of different impregnation temperatures,pre-oxidation,carbonization temperatures and activation conditions on the iodine value and carbon deviations was discussed.SEM,EDS,and BET techniques were used to investigate the microstructures and properties of materials.Results showed that activated carbon functional ceramic exhibited excellent comprehensive properties when porous ceramics adsorbed the coal pitch at 150 ℃ for 0.5 h,oxidized at 420 ℃ for 1.0 h,and carbonizated at 700 ℃ for 1.0 h and then activated by using KOH(20wt%) as agent at 800 ℃ for 1.0 h,as confirmed by the high iodine value(162.6 mg/g) and high specific surface area(83.5 m2/g).     

The Analysis of Pore Development and Formation of Surface Functional Groups in Bamboo-Based Activated Carbon during CO2 Activation

Pore development and the formation of oxygen functional groups were studied for activated carbon prepared from bamboo (Bambusa bambos) using a two-step activation with CO₂, as functions of carbonization temperature and activation conditions (time and temperature). Results show that activated carbon produced from bamboo contains mostly micropores in the pore size range of 0.65 to 1.4 nm. All porous properties of activated carbons increased with the increase in the activation temperature over the range from 850 to 950 °C, but decreased in the temperature range of 950 to 1000 °C, due principally to the merging of neighboring pores. The increase in the activation time also increased the porous properties linearly from 60 to 90 min, which then dropped from 90 to 120 min. It was found that the carbonization temperature played an important role in determining the number and distribution of active sites for CO₂ gasification during the activation process. Empirical equations were proposed to conveniently predict all important porous properties of the prepared activated carbons in terms of carbonization temperature and activation conditions. Oxygen functional groups formed during the carbonization and activation steps of activated carbon synthesis and their contents were dependent on the preparation conditions employed. Using Boehm’s titration technique, only phenolic and carboxylic groups were detected for the acid functional groups in both the chars and activated carbons in varying amounts. Empirical correlations were also developed to estimate the total contents of the acid and basic groups in activated carbons in terms of the carbonization temperature, activation time and temperature.     

掺磷酚醛树脂炭嵌锂性能研究

以添加不同含量五氧化二磷的热塑性酚醛树脂为前驱体 ,经热固化后升温至 70 0℃裂解制备掺磷树脂裂解炭 .X射线衍射考察了裂解炭的微晶结构变化 ;恒电流技术研究了裂解炭的充放电性能 .实验表明 ,五氧化二磷的加入使树脂裂解炭微晶结构发生了很大改变 ,随着磷含量的增加微晶层间距减小 ,而且更加无序 ;其放电可逆容量随五氧化二磷掺杂量的增加先增而后减 ,当P2 O5含量为 9wt%时 ,可逆容量达到最大值 (5 2 8mA·h·g- 1) ,是未掺杂 (2 30mA·h·g- 1)的 2倍多     

Preparation and characterization of high-specific-surface-area activated carbons from K2CO3-treated waste polyurethane

An activated carbon with high specific surface area was prepared from polyurethane foam by chemical activation with K2CO3 and the influences of carbonization temperature and impregnation ratio on the pore structure of the prepared activated carbon were investigated. It was found that the specific surface area of the activated carbon was at a maximum value (about 2800 m(2)/g) at a carbonization temperature of 1073 K and at an impregnation ratio of 1.0. It was concluded that the polyurethane foam structure was modified during impregnation by K2CO3, K2CO3 promoted charring during carbonization, and then the weight loss behavior was changed below 700 and above 1000 K, carbon in the char was consumed by K2CO3 reduction, and this led to the high specific surface area. The prepared activated carbon had a very sharp micropore size distribution, compared with the commercial activated carbon having high specific surface area. The amounts of three organic vapors (benzene, acetone, and octane) adsorbed on the prepared activated carbons was much larger than those on the traditional coconut shell AC and the same as those on the commercial activated carbon except for octane. We surmised that the high specific surface area was due to the modification of the carbonization behavior of polyurethane foam by K2CO3.     

Activated carbon fibers with a high heteroatom content by chemical activation of PBO with phosphoric acid

The preparation of activated carbon fibers (ACFs) by phosphoric acid activation of poly(p-phenylene benzobisoxazole) (PBO) fibers was studied, with particular attention to the effects of impregnation ratio and carbonization temperature on porous texture. Phosphoric acid has a strong effect on PBO degradation, lowering the temperature range at which the decomposition takes place and changing the number of mass loss steps. Chemical analysis results indicated that activation with phosphoric acid increases the concentration of oxygenated surface groups; the resulting materials also exhibiting high nitrogen content. ACFs are obtained with extremely high yields; they have well-developed porosity restricted to the micropore and narrow mesopore range and with a significant concentration of phosphorus incorporated homogeneously in the form of functional groups. An increase in the impregnation ratio leads to increases in both pore volume and pore size, maximum values of surface area (1250 m(2)/g) and total pore volume (0.67 cm(3)/g) being attained at the highest impregnation ratio (210 wt % H(3)PO(4)) and lowest activation temperature (650 °C) used; the corresponding yield was as large as 83 wt %. The obtained surface areas and pore volumes were higher than those achieved in previous works by physical activation with CO(2) of PBO chars.     

KOH Direct Activation for Preparing Activated Carbon Fiber from Polyacrylonitrile-based Pre-oxidized Fiber

The activated carbon fiber（ACF） was prepared from polyacrylonitrile-based pre-oxidized fiber（PANOF） by KOH direct activation. The influence of activation conditions including impregnation ratio（the mass ratio of PANOF to KOH）, activation temperature and activation time on the pore structure and electrochemical properties of ACF was investigated, and the corresponding activation mechanism was proposed. The ACF prepared at an activation temperature of 800℃ and an impregnation ratio（the mass ratio of PANOF to KOH） of 1：2 for an activation time of 1 b in 6 mol/L KOH solution exhibits a specific surface area of 3029 m^2/g, a mesoporosity of 84.2% and a specific capacitance of 288 F/g, and shows a good capacitive performance. The prepared ACF can be used as the electrode material for supercapacitors.     

载Mo和Ni-Mo酚醛树脂基活性炭加氢催化转化羰基硫的研究

将水溶性酚醛树脂与金属盐溶液混合形成均相体系,依次通过减压蒸馏、固化、炭化、活化和预硫化处理制备负载金属硫化物的活性炭脱硫剂;研究其对羰基硫（COS）的加氢转化催化活性,考察了担载金属的种类、担载量、反应温度、反应时间和COS入口浓度等因素对催化反应的影响。研究结果表明,水溶性酚醛树脂是制备催化剂炭载体的理想前驱体;Ni Mo双组分催化剂对COS的加氢催化转化活性明显高于Mo单组分催化剂;在金属硫化物/活性炭催化剂上,COS的催化加氢过程属于内扩散控制,加氢反应气氛中一定浓度含硫组分的存在是抑制催化剂失硫及维持其催化活性的必要条件。     

基于松香酸酐的环氧树脂体系固化动力学及TTT图绘制

研制了基于松香酸酐固化剂的生物质环氧树脂体系,采用全动态DSC法研究了树脂体系的固化反应动力学,通过半经验的唯象模型拟合得到了固化反应参数,活化能Ea为59.68 kJ/g,指前因子A0为1.28×1015s-1,反应级数n为2.483,由此建立了体系固化温度/时间/固化度间的关系;采用恒温DSC及DMA方法测试玻璃化转变温度,应用DiBenedetto经验方程拟合得到了玻璃化转变温度与固化度间的关系.应用锥板旋转黏度计测试了树脂体系不同温度下的凝胶时间,通过线性回归分析得到了凝胶时间与温度之间的关系.由唯象模型和DiBenedetto方程分别计算得到凝胶时的固化度为0.386,玻璃化转变温度为26.22°C.由上述工作绘制了基于松香酸酐生物质树脂体系的TTT(time-temperature-transition diagram)固化图,可确定树脂体系在不同温度任意时间下的状态.     

低温一步法活性炭基脱硫剂的制备与评价

以木屑为原料,在低温条件下一步法制得活性炭基吸附剂,考察了吸附剂制备条件和液-固、气-固吸附条件对吸附剂脱硫性能的影响。结果表明,吸附剂的最佳制备条件为,浸渍液与木屑质量比为1：1,浸渍液中硝酸质量分率为30%、吸附剂表面NiO负载量为5%,常温下浸渍24 h,400℃焙烧3 h。该吸附剂在0.2 g吸附剂/10 mL模拟油、温度为40℃及时间为5 h的液-固吸附脱硫的条件下,脱硫率为28.36%,吸附四次后饱和吸附硫容量可达2.34 mgS/g;在气-固吸附温度为250℃、空速为6.3 h^-1的条件下,饱和吸附硫容量为2.37 mgS/g;高温气-固吸附脱硫对吸附剂的影响表明,与脱硫前相比,吸附剂在比表面积、总孔体积、微孔体积均有明显提高,这说明气-固吸附脱硫过程同时实现了活性炭的扩孔活化。甲苯溶剂再生实验表明,经五次再生后吸附剂的再生性能均可达90%以上。     

Impregnated active carbons to control atmospheric emissions. 2. Influence of the raw material on the porous texture

The preparation of impregnated active carbons was optimized, in order to use them as catalysts for the deep oxidation of volatile organic compounds on atmospheric emissions. When impregnation is performed on the raw material or after activation, the influence of raw material on the texture and on the catalyst dispersion is already well studied. This paper aims to analyze the influence of raw material when the impregnation step is performed after the carbonization of different carbon precursors, as yet knowledge is very scarce. Olive stones, pinewood sawdust, nut shells, and almond shells were used as raw materials. In order to evaluate the influence of impregnation methodology of CoO, Co(3)O(4), and CrO(3) on the catalyst dispersion in the porous carbon texture, the impregnation step was made after activation and between carbonization and activation. On the first sequence, for all the raw materials, the impregnated oxides must be deposited on the internal surface, blocking part of the initial porous texture. When the impregnation step is conducted after carbonization, metal species act as catalysts during the activation step. The textures developed strongly depend either on the raw material or on the chemical state and distribution of the catalyst in the carbonized material. Olive stones and sawdust carbons stay with a microporous texture with very narrow pores where catalysts are not deposited. In nut shell and almond shell carbons, metal species are dispersed in the largest micropores and in a well-developed mesoporous texture.     

K_2CO_3活化制备花椒籽废渣的活性炭及其对对硝基苯酚的吸附性能

采用花椒籽废渣(RPS)为原料,K_2CO_3为活化剂制备了花椒籽废渣活性炭(KAC),以期实现农业废弃物的再利用。采用傅里叶变换红外光谱仪(FTIR)、扫描电子显微镜(SEM)、热重分析仪(TGA)、能量散射光谱(EDS)、X射线衍射仪(XRD)和气体吸附法等技术手段对其进行表征。分析了浸渍比(m(K_2CO_3)∶m(RPS))、浸渍时间、活化温度和活化时间对制备花椒籽废渣活性炭的影响,并且测试了花椒籽废渣活性炭对对硝基苯酚的吸附行为。研究结果表明,在浸渍比为0.8,浸渍时间为12 h,活化温度为550℃,活化时间为60min的条件下,活性炭的产率为29.3%,比表面积为1210 m~2/g,碘值为1002 mg/g,对亚甲基蓝的平衡吸附容量为362 mg/g,灰分为2.2%,水分为6.6%。对对硝基苯酚的吸附性能研究表明,293 K,pH=8.0,吸附180min后可达到吸附平衡,对硝基苯酚的吸附容量为406 mg/g,吸附可用Langmuir等温方程较好模拟,吸附为自发的放热过程。动力学研究表明该吸附符合准二级动力学模型。K_2CO_3活化法制备花椒籽废渣活性炭原料廉价,工艺简单,制得的活性炭吸附性能优异,具有较好的应用前景。     

纤维素纳米晶模板法制备多级孔炭材料及其电化学性能

以纤维素纳米晶(CNC)为模板,酚醛树脂为碳源,KOH为活化剂,通过高温碳化制备了多级孔炭材料.采用透射电子显微镜(TEM)、扫描电子显微镜(SEM)和X射线光电子能谱仪(XPS)等手段对合成的一系列炭材料进行了表征.结果表明,前驱体中CNC的降解会形成与CNC直径相当的介孔,KOH活化则会导致炭材料产生大量的微孔和大孔,以及部分4 nm左右较小尺度的介孔,所制备炭材料呈现明显的多级孔特性,其比表面积达554.7 m²/g,总孔体积为0.323 cm³/g.以CNC为模板,KOH活化的炭材料作为电极材料时,在1.0 A/g电流密度下其比电容达202.8 F/g,当电流密度升高至40.0 A/g时,其电容保持率仍达69%,表明该炭材料具有优异的倍率性能;由该电极材料组装的超级电容器在10000次充放电循环后,电容保持率达95%以上,具有良好的循环稳定性.     

Characteristics of activated carbon prepared from pistachio-nut shell by zinc chloride activation under nitrogen and vacuum conditions

Activated carbons with well-developed pore structures were prepared from pistachio-nut shells by chemical activation using zinc chloride under both nitrogen atmosphere and vacuum conditions. The effects of preparation parameters on the carbon pore structure were studied in order to optimize these parameters. It was found that under vacuum conditions, the characteristics of the activated carbons produced are better than those under nitrogen atmosphere. The impregnation ratio, the activation temperature, and the activation hold time are the important parameters that influence the characteristics of the activated carbons. The optimum experimental conditions for preparing predominantly microporous activated carbons with high pore surface area and micropore volume are an impregnation ratio of 0.75, an activation temperature of 400 degrees C, and a hold time of 1 h. Under these conditions, the BET surface areas of the carbons activated under nitrogen atmosphere and vacuum conditions were 1635.37 and 1647.16 m2/g, respectively. However, at a ZnCl2 impregnation ratio of 1.5, a furnace temperature of 500 degrees C, and a hold time of 2 h, the predominantly mesoporous activated carbon prepared under vacuum condition had a BET surface area of 2527 m2/g. Fourier transform infrared spectra were used to detect changes in the surface functional groups of the samples during the different preparation stages.     

Investigation on effects of operating conditions in combined activation of char to develop the pore structure

In this study, activation of pistachio shell char was investigated by chemical, physical and combined activation experimentally using a TGA instrument and lab scale reactor. The effects of operating conditions such as activation time, temperature and impregnation ratio in the activation methods were studied via the weight loss and iodine number of the samples. The results showed that combined activation is the premium activation method. In addition, in this method. a temperature of 800 °C, a dwell time of 45 min and an impregnation ratio of 50 % are the optimum conditions which give a product with an iodine number of 2433 mg/g and a weight loss 52 %. A high iodine number of this activated carbon was developed at a moderate temperature and dwell time, and the weight loss confirms the advantages of the combined activation method. The products were characterized by SEM and FTIR analyses.     

蜂巢状多孔明胶制备高性能超级电容器用活性炭

近年来,以生物质为前驱体来制备碳材料因其资源丰富、廉价易得、无污染且可再生等优点而引起人们的广泛关注。本文将生物质明胶制备成呈蜂巢状的多孔结构,并以此为前驱体经碳化、活化制备活性炭。研究表明,与商品化明胶相比,由多孔明胶所制备的活性炭其比表面积(可高达3692 m~2?g1)及超级电容器性能均有明显提升。在6 mol?L~(-1) KOH水溶液中,由多孔明胶经600°C碳化、700°C KOH活化所制备的活性炭,在1 A?g~(-1)的放电容量为357 F?g~(-1),即使在100 A?g~(-1)的大电流密度下,其比电容仍可维持在227 F?g~(-1)。活性炭样品也表现出优异的循环稳定性,在10 A?g~(-1)下经7500圈循环稳定性测试后,其初始容量保持率高达93.0%。而且,以该活性炭组装的对称型超级电容器,在250、2500及25000 W?kg~(-1)的功率密度下,其能量密度分别为10.3、9.7和8.2 Wh?kg~(-1);在10 A?g~(-1)下经10000次循环后,容量保持率高达97.6%。这些研究结果表明由蜂巢状多孔明胶所制备的活性炭在高性能超级电容器中具有巨大的应用潜力。     

双电层电容器用新型无灰煤(HyperCoal)基活性炭的制备

以无灰煤(HyperCoal)为原料,KOH和CaCO3为活化剂制备了煤基活性炭,采用低温N2吸附法表征了活性炭的比表面积和孔结构,测定了活性炭用作双电层电容器(EDLC)电极材料的电化学性能。考察了炭化温度、活化温度、活化时间和活化剂对活性炭电容特性的影响。研究结果表明,比表面积和比电容随着炭化温度的升高而降低,活化温度过高或活化时间太长对比电容有不利影响。此外,CaCO3影响活化过程中孔的开发,显著降低所制备活性炭的比表面积和比电容。在炭化温度为500℃、活化温度为800℃、KOH与焦的质量比为4∶1和活化时间2 h下所得活性炭的比表面积和总孔容分别达到2 540 m2/g和1.65 cm3/g,该活性炭电极在0.5 mol/L TEABF4/PC电解液中的比电容达到最大值46.0 F/g。     

Preparation of activated carbon from sawdust by zinc chloride activation

A series of activated carbons were prepared from sawdust by zinc chloride activation in different operation conditions. The effects of operation parameters such as impregnation ratio, activation temperature and time on the adsorption properties of activated carbons were measured and analyzed in order to optimize these operation conditions. The experimental results show that under the experimental circumstances studied, both the yield and the adsorption for iodine and methylene blue of activated carbon can reach a relatively higher value in the chemical activation process with the impregnation ratio of 100% ZnCl₂/sawdust in the activation temperature of 500 °C carbonized for 60–90 minutes which are the optimum activation conditions in making wood activated carbon. The most important operation parameter in chemical activation with zinc chloride was found to be the impregnation ratio.     

Structural Characterization and Property Study on the Activated Alumina-activated Carbon Composite Material

AlCl3,NH3·H2O,HNO3 and activated carbon were used as raw materials to prepare one new type of activated alumina-activated carbon composite material.The influence of heat treatment conditions on the structure and property of this material was discussed;The microstructures of the composite material were characterized by XRD,SEM,BET techniques;and its formaldehyde adsorption characteristic was also tested.The results showed that the optimal heat treatment temperature of the activated alumina-activated carbon composite material was 450 ℃,iodine adsorption value was 441.40 mg/g,compressive strength was 44 N,specific surface area was 360.07 m2/g,average pore size was 2.91 nm,and pore volume was 0.26 m3/g.According to the BET pore size distribution diagram,the composite material has dual-pore size distribution structure,the micro-pore distributes in the range of 0.6-1.7 nm,and the meso-pore in the range of 3.0-8.0 nm.The formaldehyde adsorption effect of the activated alumina-activated carbon composite material was excellent,much better than that of the pure activated carbon or activated alumina,and its saturated adsorption capacity was 284.19 mg/g.     

汽油活性炭基脱硫吸附剂的制备与评价

以250℃温度下浓硫酸改性后的活性炭为载体,采用浸渍法制备了以MnO₂为活性组分的活性炭基的汽油脱硫吸附剂MnO₂/AC,考察了吸附剂的制备条件及脱硫条件对脱硫效果的影响。研究结果表明,适宜的吸附剂制备条件为,以Mn(NO₃)₂为活性组分前驱物,Mn(NO)₂浸渍液浓度0.15mol/L、常温下浸渍24h、焙烧温度350℃、焙烧时间2h。该吸附剂在静态吸附温度120℃、吸附时间2h、剂油质量比0.10的条件下可使原料油硫的质量分数从628.6×10^-6降至221.5×10^-6,脱硫率达到64.8%;在动态吸附温度60℃、空速1.76h^-1的条件下,初始流出汽油硫的质量分数降至21.8×10^-6,初始脱硫率达到96.5%。     

Chemical assembly of TiO2 and TiO2@Ag nanoparticles on silk fiber to produce multifunctional fabrics

Activated carbon fibers (ACFs) were prepared by chemical activation of poly(p-phenylene terephthalamide (PPTA) with phosphoric acid, with a particular focus on the effects of impregnation ratio and carbonization temperature on both surface chemistry and porous texture. Thermogravimetric studies of the pyrolysis of PPTA impregnated with different amounts of phosphoric acid indicated that this reagent has a strong influence on the thermal degradation of the polymer, lowering the decomposition temperature and increasing the carbon yield. As concerns surface chemistry, TPD and chemical analysis results indicated that the addition of phosphoric acid increases the concentration of oxygenated surface groups, with a maximum at an impregnation ratio of 100 wt.%. The resulting materials present uncommon properties, namely a large amount of oxygen- and phosphorus-containing surface groups and a high nitrogen content. Porosity development following H(3)PO(4) activation was very significant, with values close to 1700 m(2)/g and 0.80 cm(3)/g being reached for the BET surface area and total pore volume, respectively. The pore size distributions remained confined to the micropore and narrow mesopore (<10 nm) range.