Hydrodynamic thickness of petroleum oil adsorbed layers in the pores of reservoir rocks

The hydrodynamic thickness delta of adsorbed petroleum (crude) oil layers into the pores of sandstone rocks, through which the liquid flows, has been studied by Poiseuille's flow law and the evolution of (electrical) streaming current. The adsorption of petroleum oil is accompanied by a numerical reduction in the (negative) surface potential of the pore walls, eventually stabilizing at a small positive potential, attributed to the oil macromolecules themselves. After increasing to around 30% of the pore radius, the adsorbed layer thickness delta stopped growing either with time or with concentrations of asphaltene in the flowing liquid. The adsorption thickness is confirmed with the blockage value of the rock pores' area determined by the combination of streaming current and streaming potential measurements. This behavior is attributed to the effect on the disjoining pressure across the adsorbed layer, as described by Derjaguin and Churaev, of which the polymolecular adsorption films lose their stability long before their thickness has approached the radius of the rock pore.     

CO2 adsorption on granular and monolith carbonaceous materials

We evaluated the CO₂ adsorption capacity on granular and monolith carbonaceous materials, obtained by chemical activation of African palm stones with H₃PO₄, ZnCl₂ and CaCl₂ solutions at different concentrations. Textural properties of the synthesized materials were analyzed using N₂ adsorption measurements at 77 K, the isotherms showed obtaining of materials microporous and moderately mesoporous, with surface areas between 161 and 1700 m²/g and pore volume between 0.09 and 0.64 cm³ g⁻¹. Were observed different behaviors for textural parameters in each series, associated with the activating agent used in the preparation. The materials obtained have a CO₂ adsorption capacity between ∼114 and 254 mg CO₂/g, at atmospheric pressure and 273 K. It was established that the total amount of CO₂ adsorbed under these experimental conditions is defined by the narrow micropore volume (V_n) and increased the total basicity of the materials.     

Adsorption of hydrogen on Pt(1 1 1) and Pt(1 0 0) surfaces and its role in the HOR

Hydrogen adsorption isotherms, evaluated by combination of cyclic voltammetry and chronoamperometry, are reported on Pt(1 1 1) and Pt(1 0 0) surfaces in 0.1 M HClO₄. We found that at E > 0.05 V Pt(1 1 1) and Pt(1 0 0) are only partially covered by the adsorbed hydrogen (H_ad). On both surfaces, a full monolayer of the adsorbed hydrogen is completed at −0.1 V, i.e. the adsorption of atomic hydrogen is observed in the hydrogen evolution potential region. We also found, that the activity of the hydrogen oxidation reaction is mirrored by the shape of the hydrogen adsorption isotherms, implying that H_ad is in fact a spectator in the HOR.     

(Amino acid + silica) adsorption thermodynamics: Effects of temperature

A thorough understanding of amino acid adsorption by mineral and oxide surfaces has a major impact on a variety of industrial and biomedical applications. Little information currently exists regarding temperature effects on most of these adsorption processes. Deeper thermodynamic analyses of their multiple temperature adsorption isotherms would aid the interpretation of the interfacial interactions. Low solution concentration adsorption isotherms for glycine, lysine and glutamic acid on a silica adsorbent were generated for T = (291, 298 and 310) K. Data analysis via the Clausius–Clapeyron method yielded the isosteric heat of adsorption as a function of fractional monolayer coverage for each adsorptive. Each amino acid showed an exothermic adsorption response. Glycine and lysine experienced a greater negative effect of increased temperature compared with glutamic acid, indicating a greater number of adsorbed molecules than glutamic acid, with the former undergoing intermolecular clustering within the adsorbed phase. Isosteric heat analyses suggest ionic interactions for lysine and hydrogen bonding for glutamic acid, both weakening with increased coverage. In contrast, initial hydrogen bonding led to ionic bonding for glycine with increasing coverage.     

The role of bentonite addition in UF flux enhancement mechanisms for oil/water emulsion

The main problem in treating oil/water emulsion from car wash waste-water by ultrafiltration (UF) is fouling caused by oil adsorption on the membrane surface and internal pore walls. This study demonstrates that the addition of bentonite clay can reduce the adsorption layer on cellulose acetate UF membrane, resulting in a reduction of total membrane resistance (R_t). Experiments were conducted to identify and describe three possible mechanisms: (i) bulk oil emulsion concentration reduction; (ii) particle aggregation and (iii) detachment of the adsorbed gel layer by shear force. Adsorption of oil emulsion by bentonite can lead to a significant reduction of bulk oil emulsion concentration, one of the major causes of flux enhancement. Results show that contact of oil emulsion with bentonite forms larger particles resulting in flux increment. An optimum particle size of 37 μm, corresponds with a bentonite concentration of 300 mg/l and provided the highest flux. Beyond this limiting concentration, flux improvement gradually declined, possibly due to the formation of packed cake of particles on the membrane surface. The presence of bentonite in the oil emulsion promotes high shear stress which acts against the gel layer. This high shear stress, caused by bentonite particles and cross-flow velocity, reverses the adsorbed gel layer to the bulk of the liquid phase.     

The adsorption behavior of cationic surfactant onto human hair fibers

Quaternary ammonium surfactants are important ingredients that are frequently formulated into hair care products to modify the properties of hair surface. The adsorption kinetics, isotherms and association structures of cationic surfactants on hair surface, however, are not fully understood due to the heterogeneous nature of human hair fibers. In this work, a quaternary ammonium of surfactant, dimethylpabamidopropyl laurdimonium tosylate (DDABDT) was chosen as a probe to investigate the adsorption behavior of cationic surfactant on cuticles of scalp hair. The results reveal that the adsorption kinetics fit to a pseudo-second-order kinetic model and the adsorption isotherms fit to the Freundlich adsorption model. With the increase of DDABDT adsorption, the wettability of hair fibers changes from hydrophobic to hydrophilic. The association structure could be monolayer or bilayer depending on the initial concentration of the surfactant. In the monolayer structure, the ‘anchor’ surfactant molecules are believed to adsorb vertically on the surface of hair fibers through electrostatic interaction. In the bilayer structure, the second layer molecules may then pile up on top of the first layer with charged groups orienting outward. The thickness of DDABDT film on hair fibers treated with 5 × 10^?4 mol/l DDABDT solution is measured to be 5.42 nm on average with a force–distance method. This figure is very close to the two times of the theoretical molecular size of the DDABDT molecule.     

Thermodynamic analysis of sorption isotherms of bentonite

Sorption isotherms of water vapour on commercial bentonite clay are determined at T = (303, 323, and 343) K. The sorption isotherms have a sigmoid shape (Type II). At a given water activity, moisture content decreases with increasing temperature. Hysteresis between adsorption and desorption isotherms is shown over most the range of water activity varying from 0.1 to 0.9. The fitting of the experimental data by using two theoretical models (Guggenheim–Anderson–DeBoer (GAB) and Henderson) shows that the two models reproduce experimental data with acceptable accuracy. The GAB model, however, is largely superior. The isosteric sorption enthalpy is determined and its dependency on the amount of water retention is investigated. It is found that the enthalpy reaches a maximum value when a monolayer of water covers the adsorbant surface. The enthalpy decreases asymptotically to a finite value when the amount of adsorbed water increases.     

Adsorptive property of Cu2+–ZnO/cetylpyridinium–montmorillonite complexes for pathogenic bacterium in vitro

Cu²⁺–ZnO/cetylpyridinium–montmorillonite (Cu²⁺–ZnO/CP–MMT) complexes were prepared using montmorillonite (MMT), Cu²⁺, Zn²⁺, and cetylpyridinium (CP). The goal was to assess comparatively the adsorption properties of Cu²⁺–ZnO/CP–MMT in vitro using pathogenic Escherichia coli. The results showed that Cu²⁺–ZnO/CP–MMT adsorbed significantly (P < 0.05) more E. coli compared with the parent clay. The adsorption process of bacterial cells occurring on the modified MMT surface reached equilibrium after 90 min. The percentages of E. coli adsorbed onto the surfaces of Cu²⁺–ZnO/CP–MMT and MMT in adsorption equilibrium were 84.66% and 47.01%, respectively. Adsorption data from the bacteria-clay systems followed the Langmuir and Freundlich isotherms, but not the BET isotherm. Adsorption of E. coli in acidic medium was higher than in alkaline medium. The extent of bacteria adsorption onto the modified MMT increased with decreasing ionic strength, and with increasing temperature. The processes of E. coli adsorption onto the tested adsorbents were endothermic and spontaneous at the experimental temperature. The mechanism of adsorption of bacteria on Cu²⁺–ZnO/CP–MMT may involve enhanced hydrophobicity and the reversal of surface charge from negative to positive.     

Adsorption behaviour and surfactant elution of cationic salivary proteins at solid/liquid interfaces,studied by in situ ellipsometry

Adsorption of the cationic salivary proteins lactoferrin, lactoperoxidase, lysozyme and histatin 5 to pure (hydrophilic) and methylated (hydrophobized) silica surfaces was investigated by in situ ellipsometry. Effects of concentration (≤10 μg ml⁻¹, for lysozyme ≤200 μg ml⁻¹) and dependence of surface wettability, as well as adsorption kinetics and elutability of adsorbed films by buffer and sodium dodecyl sulphate (SDS) solutions were investigated. Results showed that the amounts adsorbed decreased in the order lactoferrin ≥ lactoperoxidase > lysozyme ≥ histatin 5. On hydrophilic silica, the adsorption was most likely driven by electrostatic interactions, which resulted in adsorbed amounts of lactoferrin that indicated the formation of a monolayer with both side-on and end-on adsorbed molecules. For lactoperoxidase the adsorbed amounts were somewhat higher than an end-on monolayer, lysozyme adsorption showed amounts corresponding to a side-on monolayer, and histatin 5 displayed adsorbed amounts in the range of a side-on monolayer. On hydrophobized substrata, the adsorption was also mediated by hydrophobic interactions, which resulted in lower adsorbed amounts of lactoferrin and lactoperoxidase; closer to side-on monolayer coverage. For both lysozyme and histatin 5 the adsorbed amounts were the same as on the hydrophilic silica. The investigated proteins exhibited fast adsorption kinetics, and the initial kinetics indicated mass transport controlled behaviour at low concentrations on both types of substrates. Buffer rinsing and SDS elution indicated that the proteins in general were more tightly bound to the hydrophobized surface compared to hydrophilic silica. Overall, the surface activity of the investigated proteins implicates their importance in the salivary film formation.     

Kinetics,isotherm and thermodynamics for Cr(III) and Cr(VI) adsorption from aqueous solutions by crystalline hydrous titanium oxide

The synthetic crystalline hydrous titanium(IV) oxide (CHTO), an anatase variety and thermally stable up to 300 °C, has been used for adsorption of Cr(III) and Cr(VI) from the aqueous solutions, the optimum pH-values of which are 5.0 and 1.5, respectively. The kinetic data correspond very well to the pseudo-second order equation. The rates of adsorption are controlled by the film (boundary layer) diffusion, and increase with increasing temperature. The equilibrium data describe very well the Langmuir, Redlich–Peterson, and Toth isotherms. The monolayer adsorption capacities are high, and increased with increasing temperature. The evaluated ΔG^° (kJ · mol^?1) and ΔH^° (kJ · mol^?1) indicate the spontaneous and endothermic nature of the reactions. The adsorptions occur with increase in entropy (ΔS^° = positive), and the mean free energy (E_DR) values obtained by analysis of equilibrium data with Dubinin–Radushkevick equation indicate the ion-exchange mechanism for Cr(III) and Cr(VI)-adsorptions.     

Excess fibrinogen adsorption to monolayers of mixed lipids

Adsorption of fibrinogen to the monolayers of mixed lipids, dipalmitoyl phosphatidyl choline (DPPC) and eicosylamine (EA) was measured at a surface pressure of 20 mN/m by an in situ surface plasmon resonance technique. Pressure–area isotherms of DPPC + EA mixtures on water and buffer subphases indicated good lipid miscibility and some contraction of the monolayers at intermediate and higher surface pressures. Surface electric potential of the DPPC + EA monolayers showed excess values for intermediate DPPC:EA ratios. Fibrinogen adsorption and its adsorption rates from a dilute solution (0.03 mg/ml) were proportional to the fraction of EA in the monolayer indicating that protein binding was primarily driven by electrostatic interactions between positive EA charges in the monolayer and a net negative protein charge. At a higher protein concentration (0.06 mg/ml) both the fibrinogen adsorbed amount and its maximum adsorption rate showed excess values relative to the pure EA for 1:1, 2:1 and 3:1 DPPC + EA monolayers. This excess adsorption could be explained, in part, by the contraction of the monolayers with intermediate DPPC:EA ratios which resulted in an excess surface electric potential.     

Thermodynamics and kinetics of adsorption of Cu(II) from aqueous solutions onto a new cation exchanger derived from tamarind fruit shell

A novel cation exchanger (TFS-CE) having carboxylate functionality was prepared through graft copolymerization of hydroxyethylmethacrylate onto tamarind fruit shell (TFS) in the presence of N,N′-methylenebisacrylamide as a cross-linking agent using K₂S₂O₈/Na₂S₂O₃ initiator system, followed by functionalisation. The TFS-CE was used for the removal of Cu(II) from aqueous solutions. At fixed solid/solution ratio the various factors affecting adsorption such as pH, initial concentration, contact time, and temperature were investigated. Kinetic experiments showed that the amount of Cu(II) adsorbed increased with increase in Cu(II) concentration and equilibrium was attained at 1 h. The kinetics of adsorption follows pseudo-second-order model and the rate constant increases with increase in temperature indicating endothermic nature of adsorption. The Arrhenius and Eyring equations were used to obtain the kinetic parameters such as activation energy (E_a) and enthalpy (ΔH^#), entropy (ΔS^#) and free energy (ΔG^#) of activation for the adsorption process. The value of E_a for adsorption was found to be 10.84 kJ · mol^?1 and the adsorption involves diffusion controlled process. The equilibrium data were well fitted to the Langmuir isotherm. The maximum adsorption capacity for Cu(II) was 64 · 10 mg · g^?1 at T = 303 K. The thermodynamic parameters such as changes in free energy (ΔG^°), enthalpy (ΔH^°), and entropy (ΔS^°) were derived to predict the nature of adsorption process. The isosteric heat of adsorption increases with increase in surface loading indicating some lateral interactions between the adsorbed metal ions.     

Equilibrium and kinetics studies on adsorption of Cu(II) from aqueous solutions onto a graft copolymer of cross-linked starch/acrylonitrile (CLSAGCP)

A synthetic graft copolymer of cross-linked starch/acrylonitrile was used as an adsorbent for the removal of Cu(II) ions from an aqueous solution of copper nitrate hexahydrate Cu(NO₃)₂ · 6H₂O at different temperatures and fixed pH. The amount adsorbed increased with increasing concentration of Cu(II) ions and decreasing temperature. The length of time taken to reach equilibrium of the adsorption of Cu(II) ions was the same at all temperatures tested. Kinetics studies showed that the adsorption process obeyed first-order reversible kinetics and the adsorption isotherms followed the Freundlich model. Furthermore, the thermodynamic parameters, i.e. standard free energy (ΔG^∘), standard enthalpy (ΔH^∘), and standard entropy (ΔS^∘), of the adsorption process were calculated and the results are discussed in detail.     

Removal of ionic liquids and ibuprofen by adsorption on a microporous activated carbon: Kinetics,isotherms, and pore sites

Ionic liquids (ILs) are considered as emergent pollutants as their synthesis and further use at a large scale might generate environmental problems. The adsorption on activated carbons represents one of the most effective methods to remove ionic liquids and other micropollutants from wastewater. In this work, the adsorption properties on an activated carbon cloth of two pyridinium ionic liquids (4-tert-butyl-1-propylpyridinium bromide (IL1) and 4-tert-butyl-1-(2-carboxyethyl)pyridinium bromide (IL2)) newly synthesized, were compared with the ones of ibuprofen. The adsorption kinetics and isotherms were studied at pH 3 and 7.5. The adsorption thermodynamic parameters calculated from the isotherms indicate an exothermic process, typical of physisorption. The adsorption kinetics of a mixture of the molecules show a competition between ibuprofen and IL2. The location of each adsorbed ionic liquid and ibuprofen into the porosity of the activated carbon cloth was determined from N₂ (at 77 K) and CO₂ adsorption isotherms (at 273 K). The purification process of an effluent containing the ionic liquids and the ibuprofen in mixture or in single solute could be workable by adsorption on an activated cloth.     

Nanospace geometry-sensitive molecular assembly

Interaction of a molecule with micropore walls strongly depends on the micropore width. Molecules confined in the micropore tend to form an intermolecular structure inherent to each molecule/pore system in order to lower the whole molecular energy. Supercritical NO is adsorbed in micropores of zolite or activated carbon fiber in the form of a dimer at 303 K. The NO dimerization varies with the micropore width. CCl₄ molecules only in pore of pore width =1.0 nm at 303 K form a plastic crystalline structure which is observed at 246–250 K in the bulk phase. H₂O molecules are associated with each other to form an ordered assembly in carbon micropores at 303 K; the smaller the pore width, the more ordered the assembly structure. The presence of preadsorbed H₂O noticeably enhances adsorption of supercritical CH₄ in carbon micropores at 303 K due to methane nanohydrate formation, which has an optimum pore width of 1 nm.     

Kinetic and equilibrium studies of lead(II) adsorption from aqueous media by KIT-6 mesoporous silica functionalized with –COOH

An organic–inorganic hybrid mesoporous silica was synthesized via post-grafting of KIT-6 with 4-(triethoxysilyl)butyronitrile. All samples were characterized using their N₂ adsorption–desorption isotherms, XRD, FT–IR, TEM, SEM, and PT. The adsorption potential of this material for removing Pb(II) from aqueous solutions was investigated via the batch technique, and the effects of pH and contact time were studied. Experimental data showed that the maximum Pb(II) adsorption, 76%, occurred in the pH range around 6. The adsorption equilibrium was reached within 40 min for 10 wt.%COOH/KIT-6. The adsorption data were fitted using the Langmuir and Freundlich isotherms, and the obtained modeling equilibrium adsorption data suggested that the 10 wt.%COOH/KIT-6 sample contained homogeneous adsorption sites that fit the Langmuir adsorption model well. The pseudo-second-order model described well the 10 wt.%COOH/KIT-6 adsorption process. The desorption and regeneration experiments indicated that ≈95% of the metal desorbed and the adsorbent could be regenerated via an acid treatment without altering its properties.     

Electrochemical characterisation of MBaCo3ZnO7+δ (M = Y,Er, Tb) as SOFC cathode material with low thermal expansion coefficient

The electrochemical oxygen activation at high temperature was studied on a new class of oxygen-store material based on the system YBaCo₄O_7+δ. Three different porous layers made of YBaCo₃ZnO_7+δ, ErBaCo₃ZnO_7+δ and TbBaCo₃ZnO_7+δ were electrochemically tested as oxygen activation coatings and showed a very promising activity. The envisaged applications for these materials are principally as SOFC cathodes and as catalytic layer on oxygen membranes. The electrochemical performance followed the order Tb ? Y > Er at any tested temperature. Area specific resistance for the best performing material (TbBaCo₃ZnO_7+δ) ranges from 30 mΩ cm² at 850 °C to 0.46 Ω cm² at 650 °C. High temperature XRD showed that the thermal expansion coefficient (25–900 °C) in air of TbBaCo₃ZnO₇ is 9.45 × 10^?6 K^?1, which evidences the good thermochemical compatibility of this cobalt-rich electrocatalyst with YSZ/GDC electrolytes.     

Efficiency of blocking of non-specific interaction of different proteins by BSA adsorbed on hydrophobic and hydrophilic surfaces

The efficiency of a pre-absorbed bovine serum albumin (BSA) layer in blocking the non-specific adsorption of different proteins on hydrophobic and hydrophilic surfaces was evaluated qualitatively and quantitatively using infrared reflection spectroscopy supported by spectral simulations. A BSA layer with a surface coverage of 35% of a close-packed monolayer exhibited a blocking efficiency of 90–100% on a hydrophobic and 68–100% on a hydrophilic surface, with respect to the non-specific adsorption of concanavalin A (Con A), immunoglobulin G (IgG), and staphylococcal protein A (SpA). This BSA layer was produced using a solution concentration of 1 mg/mL and 30 min incubation time. BSA layers that were adsorbed at conditions commonly employed for blocking (a 12 h incubation time and a solution concentration of 10 mg/mL) exhibited a blocking activity that involved competitive adsorption–desorption. This activity resulted from the formation of BSA–phosphate surface complexes, which correlated with the conformation of adsorbed BSA molecules that was favourable for blocking. The importance of optimisation of the adsorbed BSA layer for different surfaces and proteins to achieve efficient blocking was addressed in this study.     

Electrochemical investigation of corrosion and corrosion inhibition of iron in hydrochloric acid solutions

The inhibition effect of 1-methyl pyrazole (MPA) on the acidic corrosion of iron in 1.0 M HCl was studied at different concentrations (10^?3–10^?2 M) by potentiodynamic polarization and electrochemical impedance spectroscopy, and EIS measurements. It is found from the polarization studies that methyl pyrazole (MPA) behaves mainly as anodic inhibitor in HCl. Values of polarization resistance (R_p) and double layer capacitance (C_dl) in the absence and presence of MPA in 1.0 M HCl are determined. The adsorption of MPA on iron surface from HCl is found to obey Temkin adsorption isotherm.     

AFM study of the adsorption of pyrrole and formation of the polypyrrole film on gold surface

Pyrrole (Py) adsorption and following electropolymerisation processes onto partially atomically flat Au (111) surfaces from aqueous solution of 0.1 M Py plus 0.1 M LiClO₄ have been investigated by non-contact atomic force microscopy. The adsorbed layers were examined, firstly in-situ, in solution of Py plus electrolyte and in pure electrolyte, and secondly ex-situ, in dried condition in air atmosphere. AFM images show clearly that in all cases the surface of the Au (111) electrode is covered with polymolecular adsorbed layer of Py. Electropolymerisation of the adsorbed Py layer causes some typical changes in the nanostructure of the layer: relatively larger nuclei disappear and honeycomb-like structures and ensembles of the middle size nuclei appear.