Surface and Thermodynamic Parameters of Polymeric Surfactants from Recycled Poly(ethylene terephthalate)

Recycling of PET waste was carried out in presence of diethanolamine and manganese acetate as catalyst. The produced oligomers were reacted with stearic acid and polyethylene glycol, PEG, which have different molecular weights 400, 1,000, and 4,000 to produce nonionic polymeric surfactants having different hydrophilic‐hydrophobic balance (HLB). The surface tension, critical micelle concentration (CMC), and surface activities were determined at different temperatures. Surface parameters such as surface excess concentration Γ_max, the area per molecule at interface A_min and the effectiveness of surface tension reduction (Π_CMC) were determined from the adsorption isotherms of the prepared surfactants. From the adsorption isotherm, some thermodynamic data for the adsorption process are calculated and discussed.     

支链化甜菜碱和阳离子表面活性剂在聚甲基丙烯酸甲酯表面的吸附及其润湿性质

利用座滴法研究了两性离子表面活性剂支链十六烷基(聚氧乙烯)_n醚羟丙基羧酸甜菜碱(n = 0, 3)和阳离子表面活性剂支链十六烷基(聚氧乙烯)_n醚羟丙基季铵盐溶液在聚甲基丙烯酸甲酯(PMMA)表面上的润湿性质,考察了表面活性剂类型、结构及浓度对接触角的影响趋势。研究发现,表面活性剂浓度低于临界胶束浓度(cmc)时,分子通过氢键以平躺的方式吸附到PMMA界面,亲水基团靠近固体界面, PMMA表面被轻微疏水化;表面张力和粘附张力同时降低,导致此阶段接触角随浓度变化不大。浓度高于cmc时,表面活性剂通过疏水作用吸附,亲水基团在外, PMMA表面被明显亲水改性,接触角随浓度升高显著降低。由于具有相同的支链烷基,表面活性剂类型变化和聚氧乙烯基团的引入对接触角影响不大。     

Micellization and Adsorption Parameters of Nonionic Polymeric Surfactants from Poly(ethylene terephthalate) Waste

Poly (ethylene terephthalate), PET, waste was recycled to oligomers in the presence of triethanolamine and manganese acetate as a catalyst. The produced oligomers were reacted with stearic acid and polyethylene glycol having different molecular weights 400, 1000, and 4000 to produce nonionic polymeric surfactants having different hydrophile‐hydrophobe balances (HLB). The surface tension, critical micelle concentration (CMC) and surface activities were determined at different temperatures. Surface parameters such as, surface excess concentration Γ_max, the area per molecule at interface A_min and the effectiveness of surface tension reduction (Π_CMC) were determined from the adsorption isotherms of the prepared surfactants. Some thermodynamic data for the adsorption process are calculated and discussed.     

高分子表面活性剂在固/液界面上的吸附形态

采用紫外光谱、XPS研究了羧甲基纤维素型高分子表面活性剂在硅胶 /水界面上的吸附形态 ,结果表明随着高分子表面活性剂溶液浓度增大 ,分子在硅胶表面的吸附由单层逐渐变为多层 ,生成半胶束结构 .     

Catalytic effects of sulfates on thermal degradation of waste poly(methyl methacrylate)

The thermal degradation of waste poly(methyl methacrylate) (PMMA) in the presence of ferric sulfate, cupric sulfate, aluminum sulfate, magnesium sulfate, and barium sulfate was studied by using thermogravimetric analysis (TGA) in air atmosphere. The values of apparent activation energies (E_a) calculated by Flynn-Wall-Ozawa method were found to be in the order of PMMA + Fe₂(SO₄)₃ < PMMA + Al₂(SO₄)₃ < PMMA + MgSO₄ < PMMA + CuSO₄ < PMMA + BaSO₄ < PMMA. The mechanism of catalytic degradation of PMMA in presence of the sulfates was discussed and the results showed that the catalytic effects of sulfates have a relationship with the acidity of their respective metal ions.     

Surface and volume properties of dodecylethyldimethylammonium bromide and benzyldimethyldodecylammonium bromide: II. Volumetric properties of dodecylethyldimethylammonium bromide and benzyldimethyldodecylammonium bromide

Density measurements were carried out for aqueous solutions of two cationic surfactants: dodecylethyldimethylammonium bromide (C₁₂(EDMAB)) and benzyldimethyldodecylammonium bromide (BDDAB). On the basis of the obtained results of the measurements the CMC and partial molar volumes of the surfactants studied were also determined. The obtained CMC values were also analyzed with those accounted on the basis of the surface tension data from the previous paper [J. Harkot, B. Jańczuk, J. Colloid Interface Sci. (2008), submitted for publication]. The values of CMC determined from the surface tension and density measurements for C₁₂(EDMAB) are equal to 9.9×10⁻³ and 1.5×10⁻² M and for BDDAB to 5.25×10⁻³ and 5.3×10⁻³ M, respectively. These obtained values are very similar. However, in the literature it is difficult to find the CMC values for C₁₂(EDMAB) and BDDAB determined by these two methods used by us—especially from the density measurements for BDDAB and surface tension measurements for C₁₂(EDMAB). In the case of the apparent molar volumes of C₁₂(EDMAB) there is a good agreement between the values obtained by us and those found in the literature. The CMC values for C₁₂(EDMAB) and BDDAB were also determined on the basis of their surface tension and free energy of electrostatic interactions between the polar heads of these surfactants and compared with those obtained from the surface tension and density measurements. It was found that the theoretically obtained CMC values were close to those determined from the density and surface tension data for the C₁₂(EDMAB) and that the ratios of the CMC values of the surfactants to their concentration at which the water surface tension decreased by about 20 mN/m proved that the presence of the aryl group in the BDDAB head instead of the methyl group caused that its micellization process was more inhibited in relation to its adsorption at air–water interface than that of C₁₂(EDMAB).     

Synthesis and surface activity of novel glucose ester surfactants containing carbohydrate and hydrocarbon chain

A series of glucosyl esters surfactants were synthesized based on glucose molecule by enzymatic catalysis. It could reach the highest esterification yield of 83.4% at the optimal condition, molar ratio of D-glucose and fatty acyl amino acid as 3:2 using 11% (w/w) enzyme catalyst Lipozyme 435 as catalyst in t-butanol at 40°C. The surface activities were studied, such as the critical micelle concentration (CMC), surface tension (γ_cmc), maximum excess concentration (Γ_max), minimum surface area/molecule (A_min), and the adsorption efficiency (pC₂₀); values of these were obtained by surface tension test. The results show that the longer the hydrophobic chain length, the lower the CMC and γ_cmc. The CMCs of novel glucosyl esters were between 4.4 and 1.5 mM. Further, the micellization physiochemical parameters, including Gibbs free energy of micellization (ΔG), standard enthalpy change (ΔH), and standard entropy change (ΔS) were calculated. It was indicated the micellization of glucosyl esters 9–16 was driven by entropy and deduced at different temperature.     

Interaction of Nonionic Surfactant Triton-X-100 with Ionic Surfactants

The interaction in two mixtures of a nonionic surfactant Triton-X-100 (TX-100) and different ionic surfactants was investigated. The two mixtures were TX-100/sodium dodecyl sulfate (SDS) and TX-100/cetyltrimethylammonium bromide (CTAB) at molar fraction of TX-100, α_TX-100 = 0.6. The surface properties of the surfactants, critical micelle concentration (CMC), effectiveness of surface tension reduction (γ_CMC), maximum surface excess concentration (Γ_max), and minimum area per molecule at the air/solution interface (A _min) were determined for both individual surfactants and their mixtures. The significant deviations from ideal behavior (attractive interactions) of the nonionic/ionic surfactant mixtures were also determined. Mixtures of both TX-100/SDS and TX-100/CTAB exhibited synergism in surface tension reduction efficiency and mixed micelle formation, but neither exhibited synergism in surface tension reduction effectiveness.     

Polymeric surfactants with tricyclic rigidity from natural rosin: Synthesis and dispersion of single-walled carbon nanotubes in aqueous solution

Polymeric surfactants from natural rosin containing a unique tricyclic rigid structure were prepared and their structures were characterized by IR, ¹H NMR and GPC. Their surface activities including hydrophile—lipophile balance values (HLB), emulsification properties, foaming properties, critical micelle concentration (CMC) and the minimum surface tension (γCMC) were evaluated. With the increase in ratio of hydrophobic to hydrophilic in polymeric surfactant, the CMC values of the surfactants decreased, and the emulsification and foaming properties of these surfactants increased, and the HLB values of them decreased. This type of polymeric surfactants was used to disperse single-walled carbon nanotubes (SWCNTs) in water, and their dispersal capacities were comparatively determined by UV-visible absorption spectroscopy. Thermogravimetric analysis (TGA) was used to quantify the amount of surfactant attached onto the nanotubes. More intuitive image of their dispersion states were obtained by transmission electron microscopy (TEM) and atomic force microscopy (AFM). The results showed that this type of polymeric surfactants had good dispersion capacity and dispersion stability to SWCNTs in water through strong hydrophobic attraction and weak van der Waals interactions.     

Effect of Organic Solvents on the Electrodeposition of Copper from Acidified CuSO4

Using Guerbet tetradecyl alcohol C₁₄GA (synthesized by Guerbet reaction using 1-heptanol as raw material) as intermediate, sodium Guerbet tetradecyl polyoxyethylene ether sulfates [C₁₄GA(EO)_nS, n = 1, 2, 4] were obtained through following steps: synthesizing Guerbet tetradecyl polyoxyethylene ether alcohols [C₁₄GA(EO)_nH, n = 1, 2, 4] by Williamson reaction, then esterifying with chlorosulfonic acid so as to form Guerbet tetradecyl polyoxyethylene ether alcohol sulfates [C₁₄GA(EO)_nSO₃H, n = 1, 2, 4], and finally neutralizing with sodium hydroxide; while sodium Guerbet tetradecyl sulfate(C₁₄GAS) was synthesized only through esterifying and neutralizing reactions. The structures of these anionic surfactants were determined by infrared, nuclear magnetic resonance, and element analysis. The surface activity of these surfactants was studied by means of surface tension. The results have shown that these surfactants possess higher surface activity than the common surfactant C₁₂H₂₅OSO₃Na. Branched-tail structure coming from Guerbet alcohol makes the anionic surfactant (C₁₄GAS) have higher critical micelle concentration (CMC) and better effectiveness in lowering the interface tension between air and water than their linear counterpart (C₁₄H₂₉OSO₃Na). Introducing oxyethyene group into the place between head group and tail group of the surfactant molecule with branched tail can lower the CMC, γ_cmc, and Krafft point. And the effectiveness for reducing the CMC, γ_cmc, Γ_max, and Krafft point of surfactant increased with the increase of oxyethylene group number (n = 1, 2, 4). The relationship between the molecular structure and surface activity of surfactant is discussed.     

Effect of Polymer on Dynamic Interfacial Tensions of Anionic–nonionic Surfactant Solutions

The dynamic interfacial tensions (IFTs) of enhanced oil recovery (EOR) surfactant/polymer systems against n-decane have been investigated using a spinning drop interfacial tensiometer in this paper. Two anionic–nonionic surfactants with different hydrophilic groups, C₈PO₆EO₃S (6-3) and C₈PO₆EO₆S (6-6), were selected as model surfactants. Partially hydrolyzed polyacrylamide (HPAM) and hydrophobically modified polyacrylamide (HMPAM) were employed. The influences of surfactant concentration, temperature, polymer concentration, and oleic acid in the oil on IFTs have been studied. The experimental results show that anionic–nonionic surfactants can form compact adsorption films and reach ultralow IFT (10^?3 mN/m) under optimum conditions. The addition of polymer has great influence on dynamic IFTs between surfactant solutions and n-decane mainly by the formation of looser mixed films resulting from the penetration of polymer chains into the interface. The compact surfactant film will also be weakened by the competitive adsorption of oleic acid, which results in the increase of IFT. Moreover, the penetration of polymer chains will be further destroyed surfactant/polymer mixed layer and lead to the obvious increase of IFT. On the other hand, polymers show little effect on the IFTs of 6-6 systems than those of 6-3 because of the hindrance of longer EO chain of 6-6 at the interface.     

Syntheses of cardanol-based cationic surfactants and their use in emulsion polymerisation

Six quaternary ammonium salts were designed and synthesised with moderate to high yields in three steps, based on cardanol, a low-cost and abundant renewable resource. The new ammonium salts can act as reactive surfactants due to their having both a hydrophilic ammonium group and a hydrophobic unsaturated alkyl chain. The gemini surfactants with a linker of a linear saturated aliphatic hydrocarbon chain exhibited a relatively low CMC value (≤ 0.2 mmol L^?1) and surface tension (≤ 27 mN m^?1), signifying that this kind of amphiphile exhibited good surface active properties. The photo-active gemini surfactant with critical micelle concentration (CMC) of 0.05 mmol L^?1 was used successfully as the sole emulsifier in the emulsion polymerisation of methyl methacrylate (MMA). In addition, a benzyl bromide-containing surfactant can act as both an atom transfer radical polymerisation (ATRP) initiator and an emulsifier in an activator generated by the electron transfer atom transfer radical polymerisation (AGET ATRP) of MMA in emulsion. The value of the number-average molecular mass of the resulting cardanol-end poly(methyl methacrylate) (PMMA) is M_n,GPC = 45.1 kDa, with polydispersity of 1.39.     

Mechanism of electroless deposition of Ni–W–P alloys by adding surfactants

This paper describes an electroless deposition method for the formation of a thin metallic film containing mainly nickel with significant amounts of tungsten (up to 25%) and phosphorus (5–10%). The film was deposited from an aqueous electrolyte that contained sodium tungstate as a source of tungsten, nickel sulphate as a source of nickel and hypophosphite as the reducing agent and a source of phosphorus. The surfactants were p‐hexyloxy‐p‐sodium sulphonate azobenzene (HSA) with the formula H₁₃C₆OC₆H₄N₂ C₆H₄SO₃Na and p‐hexylbenzyltriethanol ammonium chloride (HBC) with the formula H₁₃C₆H₄CH₂N⁺ (C₂H₄OH)₃Cl^?, added as stabilizers. In this study the process parameters of typical solutions, such as temperature, pH and concentration of tungstate salt and the concentration of different surfactants, were presented and discussed. Adsorption of the surfactants on a metal surface was dependent, among other things, on the structure of their hydrophobic and hydrophilic portions. The effect of adsorption of these surfactants on a metal surface was examined above and below the critical micelle concentration (CMC). The deposition process involves several reactions that occur simultaneously and are described in detail in this work. The mechanism for interaction of the surfactants with the steel surface was proposed through the isotherm for adsorption from aqueous solution. Furthermore, the surface properties of the surfactants were measured, particularly the CMC, the surface tension reduction and the maximum surface excess Γ_max. The tungsten percentage in the deposit layer was strongly influenced by the plating conditions and the critical concentration of each surfactant. The results were discussed according to the surface properties of the additive. The thin film of Ni–W–P achieved high crystal refinement and high hardness, it was smooth and uniform and it exhibited superior corrosion resistance. Copyright © 2003 John Wiley & Sons, Ltd.     

Synthesis and Surface Properties Activity of Novel Monoester Triethanolamine-Based Cationic Gemini Surfactants

The synthesis of surfactants derivatives of new two series of cationic gemini surfactants containing ethane or benzene as a spacer are described. The prepared compounds were analyzed using standard tools of analysis, elemental analysis, FTIR measurements, and H¹ NMR spectra. The influence of dimerization and of the spacer group were examined in order to establish structure-property relationships. The critical micelle concentration (CMC) of each series has been determined using equilibrium surface tension measurements. Furthermore, air/water interface parameter including effectiveness (Π_cmc), efficiency (P20), maximum surface excess (τ_max), and minimum surface area (A_min) have been also derived using Gibbs adsorption equation at 25°C. Standard free energies of micelleization were calculated and biological activities were examined. The results revealed that the dimeric surfactants have a good effect on the biological activities.     

阳离子和两性表面活性剂在聚甲基丙烯酸甲酯表面的吸附行为

利用座滴法研究了阳离子表面活性剂十六烷基醚羟丙基季铵盐(C₁₆PC)、十六烷基聚氧乙烯醚羟丙基季铵盐(C₁₆(EO)₃PC)和两性离子表面活性剂十六烷基醚羟丙基羧酸甜菜碱(C₁₆PB)、十六烷基聚氧乙烯醚羟丙基羧酸甜菜碱(C₁₆(EO)₃PB)溶液在聚甲基丙烯酸甲酯(PMMA)表面上的润湿性质, 考察了表面活性剂类型及浓度对接触角的影响趋势. 研究发现: 低浓度条件下表面活性剂分子可能以平躺的方式吸附到固体界面, 且亲水基团靠近固体界面, PMMA表面被轻微疏水化; 在高浓度时则通过Lifshitz-van der Waals 作用吸附, 亲水基团在外, PMMA表面被亲水改性. 聚氧乙烯基团(EO基团)的引入对阳离子表面活性剂的接触角影响不大; 而含有聚氧乙烯基团的两性离子表面活性剂在PMMA界面上以类似半胶束的聚集体吸附, 大幅度降低接触角.     

阴离子对阳离子表面活性剂在Al(OH)3、CaCO3粉体上吸附的影响

研究了阳离子表面活性剂十六烷基二甲基烯丙基氯化铵(CDAAC)在Al(OH)₃/水、CaCO₃/水界面上的吸附,探讨了无机阴离子对吸附量及表面电荷的影响,测定了样品的接触角和比表面。结果表明PO^3-₄的加入可提高Al(OH)₃、CaCO₃表面负电荷,有利于吸附,经吸附改性后的样品具有憎水性。     

Synthesis and combined properties of novel fluorinated cationic surfactants derived from hexafluoropropylene dimer

Three novel fluorinated surfactants with branched short fluorinated tails as hydrophobic groups, ammonium oxide as polar groups are prepared. Surface tension measurement shows that these fluorinated surfactants are ideal compounds to design new formulations in fire-fighting field.     

Surface-active properties of new cationic gemini surfactants with cyclic spacer

Three cationic gemini surface active compounds of the type (1r,4r)-1,4-dialkyl-1,4-dimethy-l-piperazine-1,4-diium bromide (Ia, Ib, and Ic), were synthesized. They were characterized using elemental analysis and ¹H-NMR spectra. Their surface-active properties were measured in aqueous solutions with different concentrations at different temperatures (25, 40, and 55°C). Various surface measurements of these gemini surfactants, (compared to the conventional one, 1-Dodecyl-1-methylpiperidinium bromide (a)) were estimated, specifically critical micelle concentration (CMC), effectiveness (π_CMC), efficiency (P_C20) as well as maximum surface excess (Γ_max) and minimum surface area (A_min). The measurements of the gemini compounds gave low CMC, high efficiency in reducing the surface tension, and intense adsorption at air/water interface. These surfactants have lower Krafft points and thus better solubility. Thermodynamic data, free energy, entropy, and enthalpy changes (ΔG°, ΔS°, and ΔH°) for micellization at the air/water interface and also for adsorption in the bulk of surface-active solutions were calculated.     

Water-Based Oil Spill Dispersants Based on Rosin Formaldehyde Resins

Water-soluble surfactants based on rosin acids were synthesized from condensed rosin acid-formaldehyde. This was completed by esterification of series of rosin acid formaldehyde resins with poly(ethylene glycol) having different molecular weights to produce series of rosin esters. The structure of the produced resins was determined by infrared and ¹HNMR analysis. The molecular weight of the produced surfactants was determined by gel permeation chromatography (GPC) technique. The surface properties of the prepared surfactants were determined by measuring the surface tension at different temperatures. The surface tension, critical micelle concentration (CMC), and surface activities were determined at different temperatures. Surface parameters such as surface excess concentration (Γmax), the area per molecule at interface (A_min), and the effectiveness of surface tension reduction (πCMC) were determined from the adsorption isotherms of the prepared surfactants. Some thermodynamic data for the adsorption process were calculated and are discussed. The dispersion efficiency of the prepared surfactants as petroleum oil spill dispersants was determined and correlated with the surface activity, concentrations of the prepared surfactants and type of petroleum crude oil.     

Emulsification and Foaming Properties of Hydrophobically Modified Gelatin

Surface active gelatins were formed by covalent attachment of hydrophobic groups to gelatin molecules by reactingN-hydroxysuccinimide esters of various fatty acids (C₄–C₁₆) with the lysine groups. The surface activity was evaluated by emulsification and foaming properties, and by adsorption at the oil–water interface. It was found that, in general, the modified gelatins are more surface active than the native gelatin. The increase in hydrophobic chain length and the number of attached alkyl chains per gelatin molecule leads to a decrease in the emulsion droplet's size and to more stable emulsions. Adsorption isotherms, at the o/w interface, show much higher surface concentration, at saturation, of the modified gelatin than the native gelatin. The modified gelatins also have high foaming ability and a high foam stability, while the maximal foam activity is obtained by the C₈modified gelatin. The foaming properties of the surface-active gelatins were also compared to that of sodium dodecyl sulfate (SDS) and it was found that below the CMC of SDS, both foam activity and stability were higher for the modified gelatins. On the other hand, above the CMC the foam activity of SDS was higher, but the foam stability was lower than for C₈–C₁₆-modified gelatins.