Micropatterning of ZnO nanoarrays by forced hydrolysis of anhydrous zinc acetate

Micropatterns of ZnO nanoarrays were simply and successfully fabricated in an aqueous solution without any high-temperature treatment and/or expensive catalyst. In situ forced hydrolysis of patterned anhydrous zinc acetate, derived by ultraviolet irradiation with a photomask, resulted in heterogeneous nucleation and growth to form ZnO nanoarrays. Micropatterns of ZnO nanoarrays were characterized by FE-SEM and XRD. ZnO nanoarrays were well site-selectively deposited on anhydrous zinc acetate coated regions at 88 degrees C. HR-TEM clarified the formation mechanism in which anhydrous zinc acetate showed a tendency of forced hydrolyzation to ZnO nanocrystals at the initial stage in the reaction solution.     

Comparative characterisation of zinc oxide thin films prepared from zinc acetate with or without water of hydration via the sol–gel method

Zinc oxide thin films were prepared using either zinc acetate dihydrate or anhydrous zinc acetate via the sol–gel method. Comparative characterisation of the crystallographical, morphological, optical/spectroscopical and electrical properties of the so-obtained films was performed. The idea of one- (in the case of the anhydrous precursor), and two- (in the other case) stage hydrolysis/condensation was postulated, which was supported by the characterisation results. The film prepared using the anhydrous precursor had a more pronounced c-axis crystal orientation preference, with a larger average crystallite size and more porous morphology. The transparency of this film was significantly lower over the UV/visible region due to its more porous morphology, which also resulted in lower intensity of the ‘near band edge emission’, and higher electrical resistivity. The overall results also suggested that anhydrous zinc acetate could be employed as a precursor for the sol–gel synthesis of zinc oxide thin films, which might have potential advantages in microelectronic and optoelectronic applications.     

Kinetically controlled catalytic formation of zinc oxide thin films at low temperature

We developed a unique method to produce ZnO thin films by kinetically controlled catalytic hydrolysis of a molecular precursor at low temperature, operating in conjunction with the vectorial control of crystal growth. Using a system in which the diffusion of a volatile catalyst into a solution of molecular precursor of the metal oxide limits the rate of hydrolysis and establishes a gradient of catalyst concentration, we investigated the nucleation of textured nanoparticles at the gas-liquid interface and characterized their subsequent growth. Use of this slow diffusion method combined with prediction of molecular species using a partial charge model enables a higher level of organizational control than obtained in other low-temperature synthesis methods, without the use of organic molecules. Various metal oxides and their morphologies and chemical compositions can be tailored for specific applications using this relatively simple approach.     

Effect of seeded substrates on hydrothermally grown ZnO nanorods

We report a study on the effect of seeding on glass substrates with zinc oxide nanocrystallites towards the hydrothermal growth of ZnO nanorods from a zinc nitrate hexahydrate and hexamethylenetetramine solution at 95 °C. The seeding was done with pre-synthesized ZnO nanoparticles in isopropanol with diameters of about 6–7 nm as well as the direct growth of ZnO nanocrystallites on the substrates by the hydrolysis of pre-deposited zinc acetate film. The nanorods grown on ZnO nanoparticle seeds show uniform dimensions throughout the substrate but were not homogenously aligned vertically from the substrate and appeared like nanoflowers with nanorod petals. Nanorods grown from the crystallites formed in situ on the substrates displayed wide variations in dimension depending upon the preheating and annealing conditions. Annealing the seed crystals below 350 °C led to scattered growth directions whereupon preferential orientation of the nanorods perpendicular to the substrates was observed. High surface to volume ratio which is vital for gas sensing applications can be achieved by this simple hydrothermal growth of nanorods and the rod height and rod morphology can be controlled through the growth parameters.     

Low-temperature polymer-assisted synthesis of shape-tunable zinc oxide nanostructures dispersible in both aqueous and non-aqueous media

We report the shape-controlled synthesis of zinc oxide (ZnO) nanostructures by a poly(vinyl methyl ether) (PVME)-assisted alkaline hydrolysis of zinc acetate at low temperature (20 °C). In this method, ZnO nanostructures of various morphologies including dumbbells, lances and triangles have been successfully prepared via a simple variation of different reaction parameters such as polymer concentration, pH of the reaction mixture and precursor concentration. However, without PVME, ZnO of such structurally uniform morphologies were not formed; rather ZnO of a mixture of defined and undefined morphologies were obtained indicating PVME-assisted the growth of such regular shaped ZnO nanostructures. HRTEM analysis of lance- and triangle-shaped samples as well as SAED patterns of all kinds of samples (dumbbell, lance and triangle) revealed that the ZnO nanostrcutures are single crystalline in nature and might form through oriented growth. XRD analysis also revealed the formation of well crystalline ZnO with a hexagonal structure. FTIR spectroscopy and TGA analysis confirmed the adsorption of PVME on the surface of ZnO nanostructures. Being a solvent adaptable polymer, the adsorbed PVME makes these shaped ZnO nanostructures highly dispersible in both polar and non-polar organic solvents including water. The extent of dispersibility in different solvents was studied by spectroscopic and microscopic techniques. Such solvent adoptability of PVME-coated ZnO nanostructures increases its ease of applications in device fabrication as well as in biological systems.     

Non-Basic Solution Routes to Prepare ZnO Nanoparticles

Nanocrystalline ZnO particles were prepared from alcoholic solutions of zinc acetate dihydrate without using base such as NaOH or LiOH through a colloid process carried out at a low temperature of 60°C. A comparative study of chemical reactions from zinc acetate dihydrate to ZnO was made using different types of monool solvents, i.e. methanol, ethanol, and 2-methoxyethanol. It was revealed that layered hydroxide zinc acetate was formed as an intermediate and its transformation into ZnO was a key reaction step in any of the solutions. Reaction time necessary for the precipitation of ZnO was greatly influenced by the solvents used. Methanol was useful for the preparation of the ZnO nanoparticles, which were chemically pure in terms of cation impurities and exhibited green photoluminescence by the ultraviolet excitation.     

Triple assembly of ZnO, large-scale hollow spherical shells with flower-like species consisting of rods grown on the outer surfaces of shells

Novel large-scale hollow ZnO spherical shells were synthesized by ionic liquids assisted hydrothermal oxidization of pure zinc powder without any catalyst at a relatively low temperature of 160 °C. X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX) and scanning electron microscopy (SEM) patterns show that the shells are composed of ZnO and the structure of the shells is very unique. Textured flower-like ZnO consisting of ZnO rods is grown on the outer surfaces of shells forming a triple assembly. Room-temperature photoluminescence spectra of the oxidized material show a sharp peak at 379 nm and a wider broad peak centered at 498 nm. The possible growth mechanism of the triple assembly of ZnO is discussed in detail.     

Structure and morphology of nanostructured zinc oxide thin films Prepared by dip-vs. spin-coating methods

In this study, we use dipping and spinning methods to coat glass slides with sol-gel ZnO thin films, composed of zinc acetate dihydrate, monoethanolamine (MEA), de-ionized water and isopropanol. The effect of the annealing temperature on the structural morphology and optical properties of these films is investigated. These ZnO films were preheated at 275 °C for 10 min and annealed either at 350, 450 or 550 °C for 60 min. As-deposited films, formed by amorphous zinc oxide-acetate submicron particles, are transformed into a highly-oriented ZnO after thermal treatment. The surface morphology, phase structure and optical properties of the thin films were investigated by scanning electron microscopy, X-ray diffraction (XRD) and optical transmittance. Both techniques produced nanostructured ZnO thin films with well-defined orientation. The annealed films were transparent in the visible range with an absorption edge at about 375 nm and a transmittance of ca 85–90% with an average diameter of 40 nm. XRD results show the film was composed of polycrystalline wurtzite, with a preferential c-axis orientation of (002) and a single sharp XRD peak at 34.40, corresponding to the hexagonal ZnO. The grain size is increased by the annealing temperature. Both coating techniques create sol-gel ZnO films with the potential for application as transparent electrodes in optic and electronic devices.     

Multiple Regulation Effects of Ammonium Acetate on ZnO Growth Process in Chemical Bath Deposition

Chemical bath deposition method has been used to synthesize a variety of ZnO morphology structures. However, the specificity and interaction of acetate and ammonium ions with ZnO crystal during the growth process remain elusive. This study contributes to understand the roles of ammonium acetate on the growth mechanism of ZnO in Zn(NO₃)₂-HMTA system. The growth process indicates that the nucleation experienced Zn²⁺-layered basic zinc salts (LBZs)-ZnO process, while the self-assembled unit changed from urchin-shaped, rod-shaped to a fully coupled twin-shaped structure with increasing ammonium acetate concentration. Ammonium acetate dominates the growth process by combing the ligand-ligand interaction of acetate ions binding to the same Zn-rich (0001) polar surface and ammonium ions regulating hexamethylenetetramine (HMTA) hydrolysis. Relatively regular hexagonal wurtzite structure and a dissolve-renucleation-regrowth process which retains the twin-shaped template and renucleates at the same position are observed at ∼10 mM ammonium acetate. Photoelectrochemistry (PEC) measurements show that the uniform hexagonal ZnO rods (Y-10, the sample named as Y-x (x represents x mM ammonium acetate, herein, x is 10 mM)) have a maximum photocurrent density of 1.54 mA cm⁻² at 1.23 V (vs. RHE), much higher than that of the dumbbell-shaped ZnO rods (Y-50, 0.20 mA cm⁻²) at the same voltage. These results provide a further explanation of morphology regulation mechanisms on ZnO synthesis processes and pave the road for more practical applications.     

The effect of surface properties on visible luminescence of nanosized colloidal ZnO membranes

Luminescence properties of nanosized zinc oxide (ZnO) colloids depend greatly on their surface properties, which are in turn largely determined by the method of preparation. ZnO nanoparticles in the size range from 3 to 9 nm were prepared by addition of tetramethylammonium hydroxide ((CH3)4NOH) to an ethanolic zinc acetate solution. X-ray diffraction (XRD) indicates nanocrystalline ZnO membranes with polycrystalline hexagonal wurtzite structure. The ZnO membranes have a strong visible-emission intensity and the intensity depends upon hydrolysis time. The infrared spectra imply a variety of forms of zinc acetate complexes present on the surface of ZnO particles. The effect of the ZnO membrane surface properties on photoluminescence is discussed.     

Growth-related properties and postgrowth phenomena in organic molecular thin films

The problem of monitoring the structural and morphological evolutions of thin films of organic molecular materials during their growth by organic molecular beam epitaxy and in the postgrowth stage is addressed here by a combination of in situ optical reflectance anisotropy measurements, ex situ optical and morphological investigations, and theoretical simulation of the material optical response. For alpha-quaterthiophene, a representative material in the class of organic molecular semiconductors, the results show that molecules crystallize in the first stage of growth in metastable structures, even when deposition is carried out at room temperature. In the postdeposition stage, the film structure evolves within a few days to the known equilibrium structure of the low temperature polymorph. When deposition is carried out at low substrate temperatures, an evolution of the film morphology is also demonstrated.     

Raman study of oriented ZnO thin films deposited by sol-gel method

ZnO films with preferred orientation along the (0 0 2) plane were successfully deposited by the sol-gel method using Zn(CH3COO)2.2H2O as starting material and inorganic precursor. A homogeneous and stable solution was prepared by dissolving the zinc acetate in a solution of ethanol and monoethanolamine. Thin films are obtained by spin-coating on glass substrates. ZnO films were obtained by preheating the spin-coated films at 300 degrees C for 10 min after each coating and postheating upto 550 degrees C for 2h. The as-deposited films are transformed into mono-oriented ZnO upon thermal treatment. The films consist of spongy particles aggregates with an uniform size and homogenous surface. The films aim to be used in optoelectronic devices. Raman spectroscopy from ZnO films and deposit solutions has been investigated. New Raman results of the deposit solution suggest that Zn-O bond forms first in solution and that these entities play the role of germs initiating the crystallization mechanisms during films annealing. Raman spectra of the annealed films show the presence of a compressive stress within the film structure.     

旋涂水溶液前驱体制备氧化锌薄膜及其性质

通过旋涂法, 采用Zn(OAc)2·2H2O和聚环氧乙烷(PEO)的水溶液为前驱体在不同的热处理温度下制备了ZnO薄膜. PEO的加入增加了溶液的成膜性, 其较低的热分解温度有利于制得纯净的ZnO薄膜. 文中考察了在不同热处理温度下制备的ZnO薄膜的形貌、结晶性、带隙(Eg)以及电导性. 原子力显微镜(AFM)测试表明在热处理温度为400、450和500 ℃制备的ZnO薄膜的粗糙度均方根值分别为3.3、2.7和3.6 nm. 采用透射电子显微镜(TEM)测试发现ZnO薄膜中含有大量纳晶粒子. 通过测试ZnO薄膜的UV-Vis吸收光谱, 根据薄膜位于373 nm处的吸收带边计算得到ZnO的带隙为3.3 eV. 通过对薄膜的电流-电压(I-V)曲线的测试计算得到在热处理温度为400、450和500 ℃制备的ZnO薄膜的电阻率分别为3.3×109、2.7×109和6.6×109 Ω·cm. 450 ℃时制备的ZnO薄膜的电阻率最小, 主要是由于较高的热处理温度有利于提高薄膜的纯度、密度和吸附氧. 而纯度较高、密度较大的薄膜电阻率比较小; 吸附氧含量增加, 晶界势垒增大, 电阻率增大. 因此在纯度和吸附氧的双重作用下450 ℃时制备的ZnO薄膜的电阻率最小, 而500 ℃时制备的ZnO薄膜的电阻率最大.     

Crystallization and Reduction of Sol-Gel-Derived Zinc Oxide Films by Irradiation with Ultraviolet Lamp

Structural changes in sol-gel films with photo-irradiation were investigated using zinc oxide (ZnO) derived from zinc acetate. The exposure of the films to an ultraviolet lamp induced hexagonal ZnO crystals in a relatively dense amorphous structure. On the other hand, the formation of zinc metal was found in a porous gel film. The photo-induced crystallization and reduction are ascribed to the electronic excitation in the metastable non-crystalline states.     

In situ and simultaneous nanostructural and spectroscopic studies of ZnO nanoparticle and Zn-HDS formations from hydrolysis of ethanolic zinc acetate solutions induced by water

The simultaneous formation of nanometer sized zinc oxide (ZnO), and acetate zinc hydroxide double salt (Zn-HDS) is described. These phases, obtained using the sol-gel synthesis route based on zinc acetate salt in alcoholic media, were identified by direct characterization of the reaction products in solution using complementary techniques: nephelometry, in situ Small-Angle X-ray Scattering (SAXS), UV-Vis spectroscopy and Extended X-ray Absorption Fine Structures (EXAFS). In particular, the hydrolytic pathway of ethanolic zinc acetate precursor solutions promoted by addition of water with the molar ratio N=[H₂O]/[Zn²⁺] = 0.05 was investigated in this paper. The aim was to understand the formation mechanism of ZnO colloidal suspension and to reveal the factors responsible for the formation of Zn-HDS in the final precipitates. The growth mechanism of ZnO nanoparticles is based on primary particle (radius ≈ 1.5 nm) rotation inside the primary aggregate (radius <3.5 nm) giving rise to an epitaxial attachment of particles and then subsequent coalescence. The growth of second ZnO aggregates is not associated with the Otswald ripening, and could be associated with changes in equilibrium between solute species induced by the superficial etching of Zn-HDS particles at the advanced stage of kinetic.     

Organic–inorganic nanocomposites of (2‐hydroxypropyl)cellulose as a precursor of nanocrystalline zinc oxide layers

The sol–gel method of synthesis of the hybrid nanocomposite films of ZnO/(2‐hydroxypropyl) cellulose (HPC) on silica glass is presented. The sol phases were prepared for different weight ratios of zinc acetate dihydrate to HPC in the presence of triethylamine (TEA). Raman spectrum of the mixture of ZnAc and HPC indicates coordinating interaction between zinc ion and HPC. The generation of ZnO nanoparticles in the HPC matrix proceeds in situ through the annealing of the gel phase at a temperature of 160°C. Identification of ZnO nanoparticles in the HPC matrix is done by using photoluminescence (PL), UV–Vis, and Raman spectroscopy. The films of ZnO/HPC nanocomposite are transparent in the visible light and show a higher energy value of absorption edge compared with ZnO in the bulk. Nanocrystalline films of ZnO were obtained by the calcination of ZnO/HPC nanocomposite at 500°C. ZnO films possess a good transparency for the visible light and high absorbance for UV light. Nanocrystallite sizes of ZnO particles were estimated from the X‐ ray lines broadening. The properties of ZnO layers were studied by the evaluation of PL, X‐ray investigation and atom force microscope (AFM) scanning, and the optical absorption edge. Copyright © 2008 John Wiley & Sons, Ltd.     

Synthesis and characterization of ZnO and ZnO:Ga films and their application in dye-sensitized solar cells

Highly crystalline ZnO and Ga-modified zinc oxide (ZnO:Ga) nanoparticles containing 1, 3 and 5 atom% of Ga3+ were prepared by precipitation method at low temperature. The films were characterized by XRD, BET, XPS and SEM. No evidence of zinc gallate formation (ZnGa2O4), even in the samples containing 5 atom% of gallium, was detected by XRD. XPS data revealed that Ga is present into the ZnO matrix as Ga3+, according to the characteristic binding energies. The particle size decreased as the gallium level was increased as observed by SEM, which might be related to a faster hydrolysis reaction rate. The smaller particle size provided films with higher porosity and surface area, enabling a higher dye loading. When these films were applied to dye-sensitized solar cells (DSSCs) as photoelectrodes, the device based on ZnO:Ga 5 atom% presented an overall conversion efficiency of 6% (at 10 mW cm(-2)), a three-fold increase compared to the ZnO-based DSSCs under the same conditions. To our knowledge, this is one of the highest efficiencies reported so far for ZnO-based DSSCs. Transient absorption (TAS) study of the photoinduced dynamics of dye-sensitized ZnO:Ga films showed that the higher the gallium content, the higher the amount of dye cation formed, while no significant change on the recombination dynamics was observed. The study indicates that Ga-modification of nanocrystalline ZnO leads to an improvement of photocurrent and overall efficiency in the corresponding device.     

双盘状ZnO的可控制备

采用水热法制备了形貌可控、 尺寸均一的双盘状ZnO. X射线粉末衍射(XRD)、 扫描电子显微镜(SEM)及透射电子显微镜(TEM)等测试结果表明, 制备的ZnO具有六方纤锌矿结构, 由2个直径约为4 μm, 厚度约为600 nm的圆盘复合而成. 考察了反应温度和乙酸锌与柠檬酸钾的摩尔比对产物形貌与尺寸的影响, 实现了双盘状ZnO的可控合成, 并初步探讨了其形成机理. 荧光光谱显示, 双盘状ZnO的紫外发射峰半高宽约为10 nm, 比块体ZnO的紫外发射峰半高宽(18 nm)窄, 表明双盘状ZnO具有更好的光学特性.     

BDIE·[Zn-Al]催化二氧化碳与氧化环己烯的共聚反应

用α二亚胺型BDIE配体(N,N′(2,6二异丙基苯基)乙二亚胺)与氧联锌铝醇盐([ZnAl])以配位的方式制备了高位阻催化体系BDIE·[ZnAl],并催化二氧化碳与氧化环己烯共聚.研究了各种因素对该反应的影响,发现最适宜的反应条件为BDIE[ZnAl]的摩尔比为0.5、反应温度为80℃、催化剂浓度为0.1gmL、二氧化碳压力为2MPa.在此条件下反应24h其催化效率达到31.6gg与其它高位阻体系相比,该催化剂用成本低的异丙醇铝和无水醋酸锌代替二乙锌,聚合操作过程简单,是一种有发展前景的催化体系.     

直接沉积法制备棒状ZnO

在溶液体系中90 ℃下, 以三乙醇胺与醋酸锌为反应试剂, 用直接沉积法合成了微米及纳米尺寸的棒状ZnO粒子, 并对粒子进行了透射电镜(TEM)、X射线衍射(XRD)、热重(TG)和差热扫描量热分析(DSC)等表征. 通过晶体的成核和生长理论初步解释了棒状ZnO粒子的形成过程.