圆管等壁温振荡流动对流换热理论研究

对等壁温边界条件下圆管内层流振荡流动对流换热问题进行理论推导。在随时间做正弦变化的速度入口条件下,经求解圆管内流体振荡时的能量方程,得到振荡流动圆管内温度场分布的解析解表达式,并利用Matlab对表达式进行直观表示。计算结果表明:等壁温边界条件下速度入口脉冲流动可引起温度随时间波动,波动随无量纲振荡频率和速度振荡幅度增加,换热效果加强,且速度振荡幅度和无量纲振荡频率存在协同作用。     

低温板翅式换热器仿真边界条件的设定

采用数值模拟的方法,研究锯齿形板翅式换热器在给定壁温、给定热流密度、冷热流体逆流布置和沿壁面长度方向变壁温这四种边界条件的传热特性,得到了在雷诺数为169、415、2725和4095的低压路氦气流动中,不同边界条件下翅片通道的局部努赛尔数沿无量纲高度方向上的分布。结果表明:对于相同Re数下,给定热流密度条件下的壁面温度分布趋势与实际工况下逆流布置时最为接近,其中间位置处局部Nu数沿无量纲高度方向上的变化曲线最为逼近,且计算得到的传热因子j值也最为贴近,所以,仿真时采用定热流边界条件能更好地真实模拟冷热流体逆流换热时的情况。     

锯齿型通道流动与换热的自维持振荡实验研究

本文对锯齿型通道内流动与换热的自维持振荡特性进行了实验研究。从可视化实验中观察到,Re300时,流场随时间几乎没有明显的变化;Re300,流动出现了明显的回流现象,且随着Re数增大,回流形成的涡增大,流动产生的涡的位置随时间呈有规律的周期性变化;在恒热流边界条件下,通道上、下壁面温度沿流动方向的变化与数值模拟所得到的Nu数、壁温的变化规律一致。     

竖直圆管中超临界压力CO2在低雷诺数下对流换热研究

本文对竖直圆管中超临界压力二氧化碳在低雷诺数条件下的对流换热进行了实验研究和数值模拟。实验中分析了不同入口温度、热流密度以及流动方向等对超临界CO2流动和换热的影响。实验结果与计算结果的比较表明:在热流密度较小的情况下实验结果与数值计算结果基本吻合;而在热流密度较大的情况下,由于浮升力的影响,流动可能提前从层流转变为湍流,使换热强化。     

不同热边界条件下超临界CO_2换热特性数值分析

本文通过数值方法对三种热边界下管内SCO_2的换热特点进行了研究,结果表明,不同于常物性流体,SOO_2在三种不同的热边界下局部换热性能有明显差异。研究发现,第一类热边界(恒定壁温)下流体的温升明显快于第二类(恒定热流密度)和第三种热边界条件(与H_2O耦合换热),而第二类和第三种热边界条件虽然壁面热流分布有差异,但SCO_2的温升过程及沿程的换热系数分布具有一定相似性。以SCO_2为工质,在对管壳式换热器管侧进行简化时,与定壁温边界相比,采用定壁热流边界与实际的双流体耦合换热工况更加接近。     

粘性耗散及变物性对多孔介质中对流换热的影响研究

本文通过理论分析、数值模拟与实验研究的综合,研究了粘性耗散及变物性对多孔介质中对流换热的影响。发现：用理想的等热流边界条件可以较好地数值模拟等热流边界条件下多孔介质中的对流换热;在实际可实现的参数条件下,粘性耗散对多孔介质中对流换热的影响不大;油的变物性对换热的影响很大—热流密度越高,对流换热越强。     

基于变传质强度因子Lee模型的流动沸腾模拟

本文基于不同流速下变传质强度因子的Lee模型,对低热通量下上升管内流动沸腾进行了数值模拟。通过分析气相分布、局部气泡行为解释了沸腾换热特性和局部传热恶化。结果表明：低热通量下,不同流速的平均气体体积分数沿管长线性分布,沿径向呈双峰状分布,峰值在壁面附近;高流速时,近壁处气体体积分数的增长速率最大。换热性能受流速影响显著,流速越大,换热系数越大;三种流速下换热系数最小值对应的气体体积分数相同,气相分布不同是换热特性产生差异的直接原因。低中流速下,壁温局部升高位置与换热系数骤降位置是一致的,表明壁面附近局部气泡附着会造成壁温的局部升高,导致传热恶化。     

非均匀热流边界条件下螺旋管内换热特性

对均匀和非均匀热流边界条件下螺旋管内湍流换热进行了数值模拟,结果表明:当螺旋管表面加热功率一定时,相同Re数下均匀热流边界条件时螺旋管截面周向局部Nu数高于非均匀热流边界条件;非均匀热流边界下充分发展段的平均Nu数小于均匀热流边界;相同的De数下,曲率较小的螺旋管换热系数大。     

槽式集热管管内混合对流换热的数值模拟

本文对均匀与非均匀热流密度条件下、压力10 MPa时的过热水蒸气在抛物槽式太阳能集热管管内充分发展段的混合对流换热过程进行了数值模拟。结果发现,在非均匀热流密度条件下,与纯强制对流换热相比:层流时,混合对流换热的阻力系数增加21%~133%,Nu提高48%~261%;湍流时,混合对流换热的阻力系数增加7%~236%,Nu提高6%~150%。特别是相比于均匀热流边界条件,非均匀热流边界条件下浮升力对流动传热的影响更为显著,传统的对于混合对流的判定标准需要修正。     

压力边界条件下微通道内气体流动换热特性研究

本文用直接模拟蒙特卡罗方法对给定进出口压力边界条件下微通道内气体的流动换热特性进行了数值模拟,给 出了壁面与流体的温差对气体沿程压力、温度及数密度分布的影响。计算结果表明,当壁温高于流体温度时,温差仅出现 在通道进出口处,但其发生机理却不同;流体可压缩性与稀薄性均得到增强,沿程压力分布更加非线性。     

Développement simultané hydrodynamique et thermique d'un écoulement laminaire dans un tube incliné en régime de convection mixte

In this work, we study numerically the heat transfer and fluid flow inside a circular inclined tube. The thermal boundary condition is that of a constant and uniform (axially and circumferentially) heat flux on the tube wall. A finite volume method is used to solve, in dimensionless form, the parabolic equations of mixed convection. The results, obtained for water with different combinations of the Grashof number and the tube inclination, show that the average heat transfer is improved and the wall shear stress is increased compared to those of pure forced flow.     

Analytical Analysis of Heat Transfer and Entropy Generation in a Tube Filled with Double-Layer Porous Media

The heat transfer and entropy generation in a tube filled with double-layer porous media are analytically investigated. The wall of the tube is subjected to a constant heat flux. The Darcy-Brinkman model is utilized to describe the fluid flow, and the local thermal non-equilibrium model is employed to establish the energy equations. The solutions of the temperature and velocity distributions are analytically derived and validated in limiting case. The analytical solutions of the local and total entropy generation, as well as the Nusselt number, are further derived to analyze the performance of heat transfer and irreversibility of the tube. The influences of the Darcy number, the Biot number, the dimensionless interfacial radius, and the thermal conductivity ratio, on flow and heat transfer are discussed. The results indicate, for the first time, that the Nusselt number for the tube filled with double-layer porous media can be larger than that for the tube filled with single layer porous medium, while the total entropy generation rate for the tube filled with double-layer porous media can be less than that for the tube filled with single layer porous medium. And the dimensionless interfacial radius corresponding to the maximum value of the Nusselt number is different from that corresponding to the minimum value of the total entropy generation rate.     

超临界压力CO2在水平圆管内流动传热数值分析

采用SST k-w低雷诺数湍流模型对加热条件下超临界压力CO2在内径di=22.14 mm,加热长度Lh=2440 mm水平圆管内三维稳态流动与传热特性进行了数值计算.通过超临界CO2在水平圆管内的流动传热实验数据验证了数值模型的可靠性和准确性.首先,研究了超临界压力CO2在水平圆管内的流动传热特点,基于超临界CO2在类临界温度Tpc处发生类液-类气“相变”的假设,揭示了水平圆管顶母线和底母线区域不同的流动传热行为.然后,分析了热流密度qw和质量流速G对水平圆管内超临界压力CO2流动换热的影响,通过获取流体域内的物性分布、速度分布和湍流分布等详细信息,重点解释了不同热流密度qw和质量流速G下顶母线内壁温度Tw,i分布产生差异的传热机理,分析结果确定了类气膜厚度d、类气膜性质、轴向速度u和湍动能k是影响顶母线壁温分布差异的主要因素.研究结果可以为超临界压力CO2换热装置的优化设计和安全运行提供理论指导.     

微胶囊化相变悬浮液层流传热强化的参数分析

通过对微胶囊相变悬浮液管内层流恒热流对流换热的数学建模和模拟计算,获得在恒热流加热边界条件下,不同参数匹配时相变糊状区的确切范围以及固液相变两条相界面的数值结果。利用该模型对影响悬浮型固液两相流传热特性的诸多参数进行了比较细致的定量分析,这些参数包括固相体积浓度、斯蒂芬(Ste)数、粒径比、无量纲相变温度区间宽度以及无量纲过冷度等。分析和模拟计算的结果显示微胶囊浓度和斯蒂芬数对管内层流传热具有最重要的影响。     

环形管环状流临界热负荷解析模型

根据环形管内流动与传热的特点,重新定义了环形管的水力直径和热周直径,基于圆管环状流CHF解析模型,得到了环形管内环状流临界热负荷解析模型。该模型可以预测环形管内沸腾两相流环状流时在不同加热方式下发生的临界热负荷,加热方式包括有内侧加热、外侧加热、两侧同时加热等。数值预测结果与文献数据比较表明本文的解析模型在P=0.57-15.01.MPa,G=198-3789.5 kgm-2s-1,xc=0.068-0.855,L/Dhe=19.3-539.5范围内预测良好。     

Heat Transfer and Pressure Drop Characteristics of Graphene Oxide/Water Nanofluid in a Circular Tube Fitted with Wire Coil Insert

In this work, heat transfer and pressure drop characteristics of graphene oxide/water nanofluid flow through a circular tube having a wire coil insert were studied. The required graphene oxide was synthesized via the Hummer method and characterized using Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (SRD), and scanning electron microscope (SEM) methods. Dispersing graphene oxide in the water, nanofluids with 0.02, 0.07, and 0.12% volume fraction were prepared. An experimental set-up was designed and made to investigate the heat transfer performance and pressure loss of nanofluids. All experiments were carried out in the constant heat flux at tube wall conditions. The volumetric flow rates of the nanofluid were adjusted at 6, 8, and 10 L/min. Thermal conductivity, specific heat, density, and viscosity as thermophysical properties of the nanofluid were calculated using graphene oxide and water properties at the average temperature via appropriate relations. These properties were applied to calculate the convective heat transfer coefficient, Nusselt number, and friction factors for each experiment. Finally, the constant and exponents of Duangthongsuk and Wongwises's correlations for Nusselt number and friction factor were corrected by experimental results. The achieved experimental data have shown good agreement with those predicted. The results have shown that 0.12 vol% of graphene oxide in the water can enhance convective heat transfer coefficient by about 77%. As a result, it can be concluded that the graphene oxide/water can be used in the heat transfer devices to achieve more efficiency.     

管外流诱导管束振动强化传热试验研究

本文提出了利用管外流体诱导振动实现强化传热的新方法.采用了一种新的传热元件-弹性管束,它对管外流体流动具有良好的振动响应特性.提出了正置三角柱脉动流发生装置,该装置可诱导起弹性管束一定频率的周期性振动,并对强化传热具有显著的促进作用.在恒热流条件下,对管外水流诱导振动强化对流换热规律进行了试验研究,得到了管外对流换热的准则方程式.     

高温吸热管内超临界CO2传热特性的数值模拟

研究超临界CO2在高温吸热管内的传热特性是将其应用于聚光太阳能热发电技术中的基础.本文对此进行了数值模拟研究,分析了流体温度、流动方向、系统压力、质量流率和热流密度对对流传热系数和Nu数的影响.结果表明:高温区(800—1050 K)的对流传热系数和Nu数受流动方向和系统压力的影响均很小,但都随着质量流率的增大以及热流密度的减小而明显增大;而随着流体温度的升高,对流传热系数近似线性增大,Nu数则近似线性减小.另外,本文研究发现在高温区可忽略浮升力对传热的影响,而由高热流密度引起的流动加速效应会明显恶化传热.最后,选取了八种管内超临界流体传热关联式与模拟结果进行对比,发现使用基于热物性修正的关联式对高温区传热数据预测的结果优于使用基于无量纲数修正的关联式得到的结果,且其中预测效果最优的关联式得到的计算结果与模拟结果之间的平均绝对相对偏差为8.1%.     

Convective Heat Transfer of a Cu/Water Nanofluid Flowing Through a Circular Tube

Abstract

Fluids in which nanometer-sized solid particles are suspended are called nanofluids. These fluids can be employed to increase the heat transfer rate in various applications. In this study, the convective heat transfer for Cu/water nanofluid through a circular tube was experimentally investigated. The flow was laminar, and constant wall temperature was used as thermal boundary condition. The Nusselt number of nanofluids for different nanoparticle concentrations, as well as various Peclet numbers, was obtained. Also, the rheological properties of the nanofluid for different volume fractions of nanoparticles were measured and compared with theoretical models. The results show that the heat transfer coefficient is enhanced by increasing the nanoparticle concentrations as well as the Peclet number.     

Non-Uniform Onset of Nucleate Flow Boiling of R-134a Inside a Glass Minichannel

The present work is an experimental investigation of the incipient boiling of R134a inside a circular glass minichannel mounted horizontally and equipped with a series of transparent indium tin oxide heaters. The effects of heat flux input levels and refrigerant mass fluxes on the onset nucleate boiling process and on the saturated boiling heat transfer rate are quantitatively explored. The flow pattern visualizations, carried on by means of a high-speed camera, show that the nucleation process is oddly non-uniform: the first vapor bubbles are always generated on the upper side of the tube and lead to a first wall temperature drop. A further increase in the heat flux values results in an increased wall superheat until bubble nucleation also originates on the lower side of the tube, causing a second wall temperature drop. Finally, at higher heat input levels, the boiling process becomes uniformly distributed on the inner tube surface. This phenomenon occurred also after a 180° rotation of the glass tube, and, after a critical analysis of the potential origins, it remains presently unexplained. An evaluation of heat transfer coefficients for low vapor quality regimes is finally presented.