MALDI‐FT‐ICR‐MS for archaeological lipid residue analysis

Soft‐ionization methods are currently at the forefront of developing novel methods for analysing degraded archaeological organic residues. Here, we present little‐used soft ionization method of matrix assisted laser desorption/ionization‐Fourier transform‐ion cyclotron resonance‐mass spectrometry (MALDI‐FT‐ICR‐MS) for the identification of archaeological lipid residues. It is a high‐resolution and sensitive method with low limits of detection capable of identifying lipid compounds in small concentrations, thus providing a highly potential new technique for the analysis of degraded lipid components. A thorough methodology development for analysing cooked and degraded food remains from ceramic vessels was carried out, and the most efficient sample preparation protocol is described. The identified components, also controlled by independent parallel analysis by gas chromatography‐mass spectrometry (GC‐MS) and gas chromatography‐combustion‐isotope ratio mass spectrometry (GC‐C‐IRMS), demonstrate its capability of identifying very different food residues including dairy, adipose fats as well as lipids of aquatic origin. The results obtained from experimentally cooked and original archaeological samples prove the suitability of MALDI‐FT‐ICR‐MS for analysing archaeological organic residues. Sample preparation protocol and identification of compounds provide future reference for analysing various aged and degraded lipid residues in different organic and mineral matrices.     

Method development for the analysis of resinous materials with MALDI‐FT‐ICR‐MS: novel internal standards and a new matrix material for negative ion mode

Matrix‐assisted laser desorption/ionization (MALDI) is a mass spectrometry (MS) ionization technique suitable for a wide variety of sample types including highly complex ones such as natural resinous materials. Coupled with Fourier transform ion cyclotron resonance (FT‐ICR) mass analyser, which provides mass spectra with high resolution and accuracy, the method gives a wealth of information about the composition of the sample. One of the key aspects in MALDI‐MS is the right choice of matrix compound. We have previously demonstrated that 2,5‐dihydroxybenzoic acid is suitable for the positive ion mode analysis of resinous samples. However, 2,5‐dihydroxybenzoic acid was found to be unsuitable for the analysis of these samples in the negative ion mode. The second problem addressed was the limited choice of calibration standards offering a flexible selection of m/z values under m/z 1000. This study presents a modified MALDI‐FT‐ICR‐MS method for the analysis of resinous materials, which incorporates a novel matrix compound, 2‐aminoacridine for the negative ion mode analysis and extends the selection of internal standards with m/z <1000 for both positive (15 different phosphazenium cations) and negative (anions of four fluorine‐rich sulpho‐compounds) ion mode. The novel internal calibration compounds and matrix material were tested for the analysis of various natural resins and real‐life varnish samples taken from cultural heritage objects. Copyright © 2017 John Wiley & Sons, Ltd.     

2,5‐Dihydroxybenzoic acid solution in MALDI‐MS: ageing and use for mass calibration

2,5‐Dihydroxybenzoic acid (DHB) is one of the most widely used and studied matrix compounds in matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry. However, the influence of ageing of the DHB solution on the MALDI mass spectra has not been yet systematically studied. In this work, the possible changes occurring in the acidified acetonitrile/water solution of the MALDI matrix compound DHB during 1‐year usage period have been monitored with MALDI‐Fourier transform ion cyclotron resonance mass spectrometer (MALDI‐FT‐ICR‐MS) and attenuated total reflectance Fourier transform infrared (ATR‐FT‐IR) spectroscopy. No significant ageing products have been detected. The ability of the aged DHB solution to act as a MALDI matrix was tested with two materials widely used in art and conservation – bone glue (a proteinaceous material) and shellac resin (a resinous material) – and good results were obtained. A number of peaks in the mass spectra measured from the DHB solution were identified, which can be used for internal calibration of the mass axis. Copyright © 2014 John Wiley & Sons, Ltd.     

High‐resolution MALDI‐TOF MS study on analysis of low‐molecular‐weight products from photo‐oxidation of poly(3‐hexylthiophene)

High‐resolution matrix‐assisted laser desorption/ionization (MALDI) time‐of‐flight mass spectrometry (TOF MS) was used for the analysis of the low‐molecular‐weight products from the photo‐oxidation of poly(3‐hexylthiophene) (P3HT) in solution and thin film. Eight new peak series were observed in the low‐mass range of the mass spectra of the products degraded in solution, and the formulas of the eight components were determined from the accurate mass. From SEC/MALDI‐TOF MS, two components were identified as the degraded products, and the other six components were derived from the fragmentation of the degraded products during the MALDI process. A mechanism for the formation of these components was proposed on the basis of the results of MALDI‐TOF MS. For the thin film degradation, a part of products in the solution degradation were observed, which supports that the oxidation of P3HT in solution and thin film proceeded in the same mechanism. This study shows that high‐resolution MALDI‐TOF MS is effective for the analysis of the low‐molecular‐weight products from P3HT photo‐oxidation and expected to be feasible for the degradation analyses of other polymers. Copyright © 2015 John Wiley & Sons, Ltd.     

Direct identification of trypanosomatids by matrix‐assisted laser desorption ionization–time of flight mass spectrometry (DIT MALDI‐TOF MS)

Accurate and rapid determination of trypanosomatids is essential in epidemiological surveillance and therapeutic studies. Matrix‐assisted laser desorption ionization/time of flight mass spectrometry (MALDI‐TOF MS) has been shown to be a useful and powerful technique to identify bacteria, fungi, metazoa and human intact cells with applications in clinical settings. Here, we developed and optimized a MALDI‐TOF MS method to profile trypanosomatids. trypanosomatid cells were deposited on a MALDI target plate followed by addition of matrix solution. The plate was then subjected to MALDI‐TOF MS measurement to create reference mass spectra library and unknown samples were identified by pattern matching using the BioTyper software tool. Several m/z peaks reproducibly and uniquely identified trypanosomatids species showing the potentials of direct identification of trypanosomatids by MALDI‐TOF MS. Moreover, this method discriminated different life stages of Trypanosoma cruzi, epimastigote and bloodstream trypomastigote and Trypanosoma brucei, procyclic and bloodstream. T. cruzi Discrete Typing Units (DTUs) were also discriminated in three clades. However, it was not possible to achieve enough resolution and software‐assisted identification at the strain level. Overall, this study shows the importance of MALDI‐TOF MS for the direct identification of trypanosomatids and opens new avenues for mass spectrometry‐based detection of parasites in biofluids. Copyright © 2016 John Wiley & Sons, Ltd.     

Laser desorption ionization of red phosphorus clusters and their use for mass calibration in time‐of‐flight mass spectrometry

Phosphorus clusters P_n (n = 1–89) are easily formed from red phosphorus by laser desorption ionization (LDI) and they cover a range of up to approx. m/z 3000 in both positive and negative ion mode. The clusters are singly charged and the spectra are simple because phosphorus is monoisotopic. The mass spectra can be measured with an acceptable resolution and intensity. The use of positively charged P_n clusters for calibration in mass spectrometry was examined and it was demonstrated that in external calibration a standard deviation of ±0.04 m/z units can be achieved even when using a common commercial matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) instrument. When used as internal standards the P_n clusters react with some analytes – C₆₀ and C₇₀ fullerenes and cucurbituril[8], for example. It was also found that red phosphorus is a suitable MALDI matrix for peptides and proteins, illustrated by the examples of a Calmix mixture of bradykinin, angiotensin, renin, adrenocorticotropic hormone ACTH fragment 18‐359 and insulin, and of insulin alone. Copyright © 2009 John Wiley & Sons, Ltd.     

Mass spectrometry of rhenium complexes: a comparative study by using LDI‐MS,MALDI‐MS,PESI‐MS and ESI‐MS

A group of rhenium (I) complexes including in their structure ligands such as CF₃SO₃‐, CH₃CO₂‐, CO, 2,2′‐bipyridine, dipyridil[3,2‐a:2′3′‐c]phenazine, naphthalene‐2‐carboxylate, anthracene‐9‐carboxylate, pyrene‐1‐carboxylate and 1,10‐phenanthroline have been studied for the first time by mass spectrometry. The probe electrospray ionization (PESI) is a technique based on electrospray ionization (ESI) that generates electrospray from the tip of a solid metal needle. In this work, mass spectra for organometallic complexes obtained by PESI were compared with those obtained by classical ESI and high flow rate electrospray ionization assisted by corona discharge (HF‐ESI‐CD), an ideal method to avoid decomposition of the complexes and to induce their oxidation to yield intact molecular cation radicals in gas state [M]^+. and to produce their reduction yielding the gas species [M]^–.. It was found that both techniques showed in general the intact molecular ions of the organometallics studied and provided additional structure characteristic diagnostic fragments. As the rhenium complexes studied in the present work showed strong absorption in the UV–visible region, particularly at 355 nm, laser desorption ionization (LDI) mass spectrometry experiments could be conducted. Although intact molecular ions could be detected in a few cases, LDI mass spectra showed diagnostic fragments for characterization of the complexes structure. Furthermore, matrix‐assisted laser desorption ionization (MALDI) mass spectra were obtained. Nor‐harmane, a compound with basic character, was used as matrix, and the intact molecular ions were detected in two examples, in negative ion mode as the [M]^–. species. Results obtained with 2‐[(2E)‐3‐(4‐tert‐buthylphenyl)‐2‐methylprop‐2‐enylidene] malononitrile (DCTB) as matrix are also described. LDI experiments provided more information about the rhenium complex structures than did the MALDI ones. Copyright © 2012 John Wiley & Sons, Ltd.     

Successful MALDI‐MS Analysis of Synthetic Polymers with Labile End‐Groups: The Case of Nitroxide‐Mediated Polymerization Using the MAMA‐SG1 Alkoxyamine

A sample pretreatment was evaluated to enable the production of intact cationic species of synthetic polymers holding a labile end‐group using matrix‐assisted laser desorption/ionization (MALDI) mass spectrometry. More specifically, polymers obtained by nitroxide‐mediated polymerization involving the MAMA‐SG1 alkoxyamine were stirred for a few hours in trifluoroacetic acid (TFA) to induce the substitution of a tert‐butyl group on the nitrogen of nitroxide end‐group by a hydrogen atom. Nuclear magnetic resonance, electrospray ionization tandem mass spectrometry, and theoretical calculations were combined to scrutinize this sample pretreatment from both mechanistic and energetic points of view. The substitution reaction was found to increase the dissociation energy of the fragile C? ON bond to a sufficient extent to prevent this bond to be spontaneously cleaved during MALDI analysis. This TFA treatment is shown to be very efficient regardless of the nature of the polymer, as evidenced by reliable MALDI mass spectrometric data obtained for poly(ethylene oxide), polystyrene and poly(butylacrylate).     

Characterization of different poly(2‐oxazoline) block copolymers by MALDI‐TOF MS/MS and ESI‐Q‐TOF MS/MS

A complete library of poly(2‐oxazoline) block copolymers was synthesized via cationic ring opening polymerization for the characterization by two different soft ionization techniques, namely matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI‐TOF MS) and electrospray ionization quadrupole time‐of‐flight mass spectrometry (ESI‐Q‐TOF MS). In addition, a detailed characterization was performed by tandem MS to gain more structural information about the block copolymer composition and its fragmentation behavior. The fragmentation of the poly(2‐oxazoline) block copolymers revealed the desired polymer structure and possible side reactions, which could be explained by different mechanisms, like 1,4‐ethylene or hydrogen elimination and the McLafferty +1 rearrangement. Polymers with aryl side groups showed less fragmentation due to their higher stability compared to polymers with alkyl side groups. These insights represent a further step toward the construction of a library with fragments and their fragmentation pathways for synthetic polymers, following the successful examples in proteomics. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Hydrazide and hydrazine reagents as reactive matrices for MALDI‐MS to detect gaseous aldehydes

The reagents 19 hydrazide and 14 hydrazine were examined to function as reactive matrices for matrix‐assisted laser desorption/ionization mass spectrometry (MALDI‐MS) to detect gaseous aldehydes. Among them, two hydrazide (2‐hydroxybenzohydrazide and 3‐hydroxy‐2‐naphthoic acid hydrazide) and two hydrazine reagents [2‐hydrazinoquinoline and 2,4‐dinitrophenylhydrazine (DNPH)] were found to react efficiently with carbonyl groups of gaseous aldehydes (formaldehyde, acetaldehyde and propionaldehyde); these are the main factors for sick building syndrome and operate as reactive matrices for MALDI‐MS. Results from accurate mass measurements by JMS‐S3000 Spiral‐TOF suggested that protonated ion peaks corresponding to [M + H]⁺ from the resulting derivatives were observed in all cases with the gaseous aldehydes in an incubation, time‐dependent manner. The two hydrazide and two hydrazine reagents all possessed absorbances at 337 nm (wavelength of MALDI nitrogen laser), with, significant electrical conductivity of the matrix crystal and functional groups, such as hydroxy group and amino group, being important for desorption/ionization efficiency in MALDI‐MS. To our knowledge, this is the first report that gaseous molecules could be derivatized and detected directly in a single step by MALDI‐MS using novel reactive matrices that were derivatizing agents with the ability to enhance desorption/ionization efficiency. Copyright © 2014 John Wiley & Sons, Ltd.     

Block length determination of the block copolymer mPEG‐b‐PS using MALDI‐TOF MS/MS

The molar mass determination of block copolymers, in particular amphiphilic block copolymers, has been challenging with chromatographic techniques. Therefore, methoxy poly(ethylene glycol)‐b‐poly(styrene) (mPEG‐b‐PS) was synthesized by atom transfer radical polymerization (ATRP) and characterized in detail not only by conventional chromatographic techniques, such as size exclusion chromatography (SEC), but also by matrix‐assisted laser/desorption ionization tandem mass spectrometry (MALDI‐TOF MS/MS). As expected, different molar mass values were obtained in the SEC measurements depending on the calibration standards (either PEG or PS). In contrast, MALDI‐TOF MS/MS analysis allowed the molar mass determination of each block, by the scission of the weakest point between the PEG and PS block. Thus, fragments of the individual blocks could be obtained. The PEG block showed a depolymerization reaction, while for the PS block fragments were obtained in the monomeric, dimeric, and trimeric regions as a result of multiple chain scissions. The block length of PEG and PS could be calculated from the fragments recorded in the MALDI‐TOF MS/MS spectrum. Furthermore, the assignment of the substructures of the individual blocks acquired by MALDI‐TOF MS/MS was accomplished with the help of the fragments that were obtained from the corresponding homopolymers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Detection of volatile organic compounds in the headspace above mold fungi by GC‐soft X‐radiation–based APCI‐MS

Mold fungi on malting barley grains cause major economic loss in malting and brewery facilities. Possible proxies for their detection are volatile and semivolatile metabolites. Among those substances, characteristic marker compounds have to be identified for a confident detection of mold fungi in varying surroundings. The analytical determination is usually performed through passive sampling with solid phase microextraction, gas chromatographic separation, and detection by electron ionization mass spectrometry (EI‐MS), which often does not allow a confident determination due to the absence of molecular ions. An alternative is GC‐APCI‐MS, generally, allowing the determination of protonated molecular ions. Commercial atmospheric pressure chemical ionization (APCI) sources are based on corona discharges, which are often unspecific due to the occurrence of several side reactions and produce complex product ion spectra. To overcome this issue, an APCI source based on soft X‐radiation is used here. This source facilitates a more specific ionization by proton transfer reactions only. In the first part, the APCI source is characterized with representative volatile fungus metabolites. Depending on the proton affinity of the metabolites, the limits of detection are up to 2 orders of magnitude below those of EI‐MS. In the second part, the volatile metabolites of the mold fungus species Aspergillus, Alternaria, Fusarium, and Penicillium are investigated. In total, 86 compounds were found with GC‐EI/APCI‐MS. The metabolites identified belong to the substance classes of alcohols, aldehydes, ketones, carboxylic acids, esters, substituted aromatic compounds, terpenes, and sesquiterpenes. In addition to substances unspecific for the individual fungus species, characteristic patterns of metabolites, allowing their confident discrimination, were found for each of the 4 fungus species. Sixty‐seven of the 86 metabolites are detected by X‐ray–based APCI‐MS alone. The discrimination of the fungus species based on these metabolites alone was possible. Therefore, APCI‐MS in combination with collision induced dissociation alone could be used as a supervision method for the detection of mold fungi.     

Estimation of peptide N–Cα bond cleavage efficiency during MALDI‐ISD using a cyclic peptide

Matrix‐assisted laser desorption/ionization in‐source decay (MALDI‐ISD) induces N–C_α bond cleavage via hydrogen transfer from the matrix to the peptide backbone, which produces a c′/z? fragment pair. Subsequently, the z? generates z′ and [z + matrix] fragments via further radical reactions because of the low stability of the z?. In the present study, we investigated MALDI‐ISD of a cyclic peptide. The N–C_α bond cleavage in the cyclic peptide by MALDI‐ISD produced the hydrogen‐abundant peptide radical [M + 2H]⁺? with a radical site on the α‐carbon atom, which then reacted with the matrix to give [M + 3H]⁺ and [M + H + matrix]⁺. For 1,5‐diaminonaphthalene (1,5‐DAN) adducts with z fragments, post‐source decay of [M + H + 1,5‐DAN]⁺ generated from the cyclic peptide showed predominant loss of an amino acid with 1,5‐DAN. Additionally, MALDI‐ISD with Fourier transform‐ion cyclotron resonance mass spectrometry allowed for the detection of both [M + 3H]⁺ and [M + H]⁺ with two ¹³C atoms. These results strongly suggested that [M + 3H]⁺ and [M + H + 1,5‐DAN]⁺ were formed by N–C_α bond cleavage with further radical reactions. As a consequence, the cleavage efficiency of the N–C_α bond during MALDI‐ISD could be estimated by the ratio of the intensity of [M + H]⁺ and [M + 3H]⁺ in the Fourier transform‐ion cyclotron resonance spectrum. Because the reduction efficiency of a matrix for the cyclic peptide cyclo(Arg‐Gly‐Asp‐D‐Phe‐Val) was correlated to its tendency to cleave the N–C_α bond in linear peptides, the present method could allow the evaluation of the efficiency of N–C_α bond cleavage for MALDI matrix development. Copyright © 2016 John Wiley & Sons, Ltd.     

Application of Z‐sinapinic matrix in peptide MALDI‐MS analysis

Since introduction of sinapinic acid (SA) and α‐cyano‐4‐hydroxycinnamic acid as matrices, successful application of matrix‐assisted laser desorption/ionization mass spectrometry started for protein/polypeptides. Both show some limitations in short peptide analysis because matrix clusters are quite abundant. Cinnamics currently used are E‐cinnamics. Here, Z‐SA as matrix for peptides is studied and compared with E‐SA and α‐cyano‐4‐hydroxycinnamic acid. Minor number of clusters is always observed in the low m/z region allowing the detection of short peptides. The results here described show that this novel matrix is a tool of choice for direct, rapid and sensitive detection of hydrophilic and hydrophobic peptides. Copyright © 2017 John Wiley & Sons, Ltd.     

The effect of temperature on the stability of compounds used as UV‐MALDI‐MS matrix: 2,5‐dihydroxybenzoic acid, 2,4,6‐trihydroxyacetophenone, α‐cyano‐4‐hydroxycinnamic acid, 3,5‐dimethoxy‐4‐hydroxycinnamic acid,nor‐harmane and harmane

The thermal stability of several commonly used crystalline matrix‐assisted ultraviolet laser desorption/ionization mass spectrometry (UV‐MALDI‐MS) matrices, 2,5‐dihydroxybenzoic acid (gentisic acid; GA), 2,4,6‐trihydroxyacetophenone (THA), α‐cyano‐4‐hydroxycinnamic acid (CHC), 3,5‐dimethoxy‐4‐hydroxycinnamic acid (sinapinic acid; SA), 9H‐pirido[3,4‐b]indole (nor‐harmane; nor‐Ho), 1‐methyl‐9H‐pirido[3,4‐b]indole (harmane; Ho), perchlorate of nor‐harmanonium ([nor‐Ho + H]⁺) and perchlorate of harmanonium ([Ho + H]⁺) was studied by heating them at their melting point and characterizing the remaining material by using different MS techniques [electron ionization mass spectrometry (EI‐MS), ultraviolet laserdesorption/ionization‐time‐of‐flight‐mass spectrometry (UV‐LDI‐TOF‐MS) and electrospray ionization‐time‐of‐flight‐mass spectrometry (ESI‐TOF‐MS)] as well as by thin layer chromatography analysis (TLC), electronic spectroscopy (UV‐absorption, fluorescence emission and excitation spectroscopy) and ¹H nuclear magnetic resonance spectroscopy (¹H‐NMR). In general, all compounds, except for CHC and SA, remained unchanged after fusion. CHC showed loss of CO₂, yielding the trans‐/cis‐4‐hydroxyphenylacrilonitrile mixture. This mixture was unambiguously characterized by MS and ¹H‐NMR spectroscopy, and its sublimation capability was demonstrated. These results explain the well‐known cluster formation, fading (vanishing) and further recovering of CHC when used as a matrix in UV‐MALDI‐MS. Commercial SA (SA 98%; trans‐SA/cis‐SA 5 : 1) showed mainly cis‐ to‐trans thermal isomerization and, with very poor yield, loss of CO₂, yielding (3′,5′‐dimethoxy‐4′‐hydroxyphenyl)‐1‐ethene as the decarboxilated product. These thermal conversions would not drastically affect its behavior as a UV‐MALDI matrix as happens in the case of CHC. Complementary studies of the photochemical stability of these matrices in solid state were also conducted. Copyright © 2008 John Wiley & Sons, Ltd.     

Multicyclic polyethers derived from 1,1,1‐tris(4‐hydroxyphenyl)ethane and 2,6‐dihalopyridines

Poly(pyridine ether)s were prepared in two ways: the polycondensation of silylated 1,1,1‐tris(4‐hydroxyphenyl)ethane (THPE) with 2,6‐difluoropyridine (method A) and the polycondensation of free THPE with 2,6‐dichloropyridine (method B). With method A, the THPE/difluoropyridine feed ratio was varied from 1.0:1.0 to 1.0:1.6. Cycles, bicycles, and multicycles were the main reaction products, and crosslinking was never observed. When ideal stoichiometry was used exclusively, multicycles free of functional groups were obtained. These multicycles were detectable in matrix‐assisted laser desorption/ionization time‐of‐flight (MALDI‐TOF) mass spectra up to B₃₈C₇₆ with a mass of approximately 32,000 Da. With method B, the reaction conditions were varied at a fixed feed ratio to achieve an optimum for the preparation of multicyclic polyethers, but because of the lower reactivity of 2,6‐dichloropyridine, a quantitative conversion was not achieved. The reaction products were characterized with MALDI‐TOF mass spectrometry, viscosity measurements, and size exclusion chromatography. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5725–5735, 2004     

Atmospheric pressure laser desorption/ionization using a 6–7 µm‐band mid‐infrared tunable laser and liquid water matrix

Due to the characteristic absorption peaks in the IR region, various molecules can be used as a matrix for infrared matrix‐assisted laser desorption/ionization (IR‐MALDI). Especially in the 6–7 µm‐band IR region, solvents used as the mobile phase for liquid chromatography have absorption peaks that correspond to their functional groups, such as O–H, CO, and CH₃. Additionally, atmospheric pressure (AP) IR‐MALDI, which is applicable to liquid‐state samples, is a promising technique to directly analyze untreated samples. Herein we perform AP‐IR‐MALDI mass spectrometry of a peptide, angiotensin II, using a mid‐IR tunable laser with a tunable wavelength range of 5.50–10.00 µm and several different matrices. The wavelength dependences of the ion signal intensity of [M + H]⁺ of the peptide are measured using a conventional solid matrix, α‐cyano‐4‐hydroxycinnamic acid (CHCA) and a liquid matrix composed of CHCA and 3‐aminoquinoline. Other than the O–H stretching and bending vibration modes, the characteristic absorption peaks are useful for AP‐IR‐MALDI. Peptide ions are also observed from an aqueous solution of the peptide without an additional matrix, and the highest peak intensity of [M + H]⁺ is at 6.00 µm, which is somewhat shorter than the absorption peak wavelength of liquid water corresponding to the O–H bending vibration mode. Moreover, long‐lasting and stable ion signals are obtained from the aqueous solution. AP‐IR‐MALDI using a 6–7 µm‐band IR tunable laser and solvents as the matrix may provide a novel on‐line interface between liquid chromatography and mass spectrometry. Copyright © 2015 John Wiley & Sons, Ltd.     

Comparison of ESI‐MS/MS and APCI‐MS methods for the quantification of folic acid analogs in C. elegans

Folic acid (FA) plays a vital role in central metabolism, including the one carbon cycle, nucleotide, and amino acid biosynthesis. The development of sensitive, accurate analytical methods to measure FA intermediates in tissues is critical to understand their biological roles in diverse physiological and pathological contexts. Here, we developed a highly sensitive method for the simultaneous quantification of FA intermediates in the nematode Caenorhabditis elegans as a model to dissect metabolic networks. The method was further validated by analyzing the worm folate pool upon RNAi knockdown of the dihydrofolate reductase gene dhfr‐1. Comparative mass spectrometry behavior of the FA analogs using two different ion sources, electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI), revealed ESI‐MS/MS to be more sensitive, but APCI‐MS provided more detailed structure inferences, which can elucidate chemical investigation and synthesis of FA analogs. Finally, we report on the use of in vitro oxidation coupled with high‐resolution mass spectrometry as a tool to discover new endogenous FA derivatives in the nematode.     

Identification of very long chain fatty acids by atmospheric pressure chemical ionization liquid chromatography‐mass spectroscopy from green alga Chlorella kessleri

A method is described for the enrichment of very long chain fatty acids (VLCFAs) from total fatty acids of heterotrophically cultivated green freshwater alga Chlorella kessleri and their identification as picolinyl esters by means of liquid chromatography‐mass spectrometry with atmospheric pressure chemical ionization (LC‐MS with APCI). The method is based on the use of preparative reversed phase HPLC of hundred‐milligram amounts and their subsequent identification by microbore APCI LC‐MS. A combination of these two techniques was used to identify unusual VLCFAs up to C₄₇, both saturated and monounsaturated, with two positional isomers (ω‐9 and ω‐26).     

Structural characterization of the ligstroside aglycone isoforms in virgin olive oils by liquid chromatography–high‐resolution Fourier‐transform mass spectrometry and H/Dexchange

A systematic structural characterization of the isomeric forms related to ligstroside aglycone (LA), one of the most relevant secoiridoids contained in virgin olive oils, was performed using reverse phase liquid chromatography with electrospray ionization Fourier‐transform single and tandem mass spectrometry, operated in negative ion mode (RPLC‐ESI(?)‐FTMS and FTMS/MS). The high mass resolution and accuracy provided by the adopted orbital trap mass analyzer enabled the recognition of more than 10 different isomeric forms of LA in virgin olive oil extracts. They were related to four different types of molecular structure, two of which including a dihydropyranic ring bearing one or two aldehydic groups, whereas the others corresponded to dialdehydic open‐structure forms, differing just for the position of a C═C bond. The contemporary presence of enolic or dienolic tautomers associated to most of these compounds, stable at room temperature (23°C), was also assessed through RPLC‐ESI‐FTMS analyses operated under H/D exchange conditions, ie, by using D₂O instead of H₂O as co‐solvent of acetonitrile in the RPLC mobile phase. As discussed in the paper, the results obtained for LA indicated a remarkable structural similarity with oleuropein aglycone (OA), the most abundant secoiridoid of olive oil, whose isoforms had been previously characterized using the same analytical approach.