Effect of calcining temperature and time on the characteristics of Sb-doped SnO2 nanoparticles synthesized by the sol–gel method

Spherical Sb-doped SnO₂ (ATO) nanoparticles were synthesized by the sol–gel route, employing SnCl₄·5H₂O and SbCl₃ as precursors in an ethanol solution. The influences of the calcining temperature and calcining time on the crystallite size, crystallinity, lattice parameters, lattice distortion ratio and the resistivity of the ATO nanoparticles were synthetically investigated. The results suggested that the ATO nanoparticles were crystallized in a tetragonal cassiterite structure of SnO₂ with a highly (1 1 0)-plane-preferred orientation. The calcining temperature had a dominating effect on the crystallite size, crystallinity, lattice distortion ratios and resistivity of the ATO. As the calcining temperature increased, the average crystallite size increased, the crystallinity was promoted accompanied by a decrease in the lattice distortion ratio and a corresponding decrease in the resistivity of the ATO. X-ray diffraction (XRD) and Fourier transform infrared spectrophotometer (FTIR) analysis revealed that Sb ions could not entirely supplant the Sn ions in the SnO₂ lattice for a calcining time of less than 0.5 h, even at a calcining temperature of 1000 °C. The ATO nanoparticles calcined at 1000 °C for 3.0 h possessed the lowest resistivity of 10.18 Ω cm.     

Preparation of nano-sized Al2O3–2SiO2 powder by sol–gel plus azeotropic distillation method

Nano-sized amorphous Al₂O₃–2SiO₂ powder was prepared by a sol–gel method coupled with azeotropic distillation. The structure of the powder was investigated by DTS, BET, TEM, FT-IR, TG-DTA and XRD, showing that n-butanol azeotropic distillation could effectively remove water from the aluminosilicate gels and prevent the formation of hard agglomerates in the drying process. The average particle diameter of the powder was about 70 nm. The largest BET specific surface area of the powder was 669 m²/g. To examine the alkali-activation reactivity of the powder, alkali-activation tests were performed with the powder reacting with sodium silicate solution. The synthetic powder was found to be highly reactive.     

In situ synthesis of CNTs/Fe–Ni/TiO2 nanocomposite by fluidized bed chemical vapor deposition and the synergistic effect in photocatalysis

Carbon nanotube (CNTs)/Fe–Ni/TiO₂ nanocomposite photocatalysts have been synthesized by an in situ fluidized bed chemical vapor deposition (FBCVD) method. The composite photocatalysts were characterized by XRD, Raman spectroscopy, BET, FESEM, TEM, UV–vis spectroscopy, and XPS. The results showed that the CNTs were grown in situ on the surface of TiO₂. Fe(III) in TiO₂ showed no chemical changes in the growth of CNTs. Ni(II) was partly reduced to metal Ni in the FBCVD process, and the metal Ni acted as a catalyst for the growth of CNTs. The photocatalytic activities of CNTs/Fe–Ni/TiO₂ decreased with the rise of the FBCVD reaction temperature. For the sample synthesized at low FBCVD temperature (500 °C), more than 90% and nearly 50% of methylene blue were removed under UV irradiation in 180 min and under visible light irradiation in 300 min, respectively. The probable mechanism of synergistic enhancement of photocatalysis on the CNTs/Fe–Ni/TiO₂ nanocomposite is proposed.     

Preparation of calcium sulfate whiskers from FGD gypsum via hydrothermal crystallization in the H2SO4–NaCl–H2O system

Little attention has thus far been paid to the potential effect of solution composition on the hydrothermal crystallization of calcium sulfate whiskers prepared from flue-gas desulfurization (FGD) gypsum. When purified FGD gypsum was used as raw material, the morphology and phase structure of the hydrothermal products grown in pure water, H₂SO₄–H₂O, NaCl–H₂O, and H₂SO₄–NaCl–H₂O solutions as well as the solubility of purified FGD gypsum in these solutions were investigated. The results indicate that calcium sulfate whiskers grow favorably in the H₂SO₄–NaCl–H₂O system. When prepared using 10–70 g NaCl/kg gypsum −0.01 M H₂SO₄–H₂O at 130 °C for 60 min, the obtained calcium sulfate whiskers had diameters ranging from 3 to 5 μm and lengths from 200 to 600 μm, and their phase structure was calcium sulfate hemihydrate (HH). Opposing effects of sulfuric acid and sodium chloride on the solubility of the purified FGD gypsum were observed. With the co-presence of sulfuric acid and sodium chloride in the reaction solution, the concentrations of Ca²⁺ and SO₄²⁻ can be kept relatively stable, which implies that the crystallization of the hydrothermal products can be controlled by changing the concentrations of sulfuric acid and sodium chloride.     

Mesoporous composite of LiFePO4 and carbon microspheres as positive-electrode materials for lithium-ion batteries

Mesoporous LiFePO₄/C microspheres consisting of LiFePO₄ nanoparticles are successfully fabricated by an eco-friendly hydrothermal approach combined with high-temperature calcinations using cost-effective LiOH and Fe³⁺ salts as raw materials. In this strategy, pure mesoporous LiFePO₄ microspheres, which are composed of LiFePO₄ nanoparticles, were uniformly coated with carbon (∼1.5 nm). Benefiting from this unique architecture, these mesoporous LiFePO₄/C microspheres can be closely packed, having high tap density. The initial discharge capacity of LiFePO₄/C microspheres as positive-electrode materials for lithium-ion batteries could reach 165.3 mAh/g at 0.1 C rate, which is notably close to the theoretical capacity of LiFePO₄ due to the large BET surface area, which provides for a large electrochemically available surface for the active material and electrolyte. The material also exhibits high rate capability (∼100 mAh/g at 8 C) and good cycling stability (capacity retention of 92.2% after 400 cycles at 8 C rate).     

Catalytic oxidation of benzene over Ce–Mn oxides synthesized by flame spray pyrolysis

Flame spray pyrolysis (FSP) was utilized to synthesize Ce–Mn oxides in one step for catalytic oxidation of benzene. Cerium acetate and manganese acetate were used as precursors. The materials synthesized were characterized using X-ray diffraction (XRD), N₂ adsorption, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), Raman spectroscopy, and H₂-temperature programmed reduction (H₂-TPR) and their benzene catalytic oxidation behavior was evaluated. Mn ions were evidenced in multiple chemical states. Crystalline Ce–Mn oxides consist of particles with size <40 nm and specific surface areas (SSA) of 20–50 m²/g. Raman spectrums and H₂-TPR results indicated the interaction between cerium and manganese oxides. Flame-made 12.5%-Ce–Mn oxide exhibited excellent catalytic activity at relatively low temperatures (T₉₅ about 260 °C) compared to other Ce–Mn oxides with different cerium-to-manganese ratios. Redox mechanism and strong interaction conform to structure analysis that Ce–Mn strong interaction formed during the high temperature flame process and the results were used to explain catalytic oxidation of benzene.     

Hydrothermal preparation of nanocrystalline ZnO2

A green hydrothermal method was proposed for the synthesis of nanocrystalline ZnO₂, using Zn₅(CO₃)₂(OH)₆ powder and 6 vol% H₂O₂ aqueous solution as the starting materials. Characterization results from X-ray diffraction, Raman, high resolution transmission electron microscopy and selected area electron diffraction revealed that the products synthesized at 80–120 °C for 6–18 h were pure cubic phase ZnO₂ nanocrystals. Room temperature photoluminescence spectra of the as-synthesized ZnO₂ nanocrystals displayed a wide and strong emission band in the visible region of about 525–570 nm upon laser excitation at 325 nm, which may have originated from their surface state and other crystal defects.     

Effects of multi-dopants (Zn and Ho) in stabilizing spinel structure for cathode materials in lithium rechargeable batteries—Novel chelated sol–gel synthesis

Multi-doped spinels, namely LiMn₂O₄ and LiZn_xHo_yMn_2−x−yO₄ (x = 0.10–0.18; y = 0.02–0.10), for use as cathode materials for lithium-ion rechargeable batteries were synthesized via sol–gel method, using lauric acid as the chelating agent, to obtain micron-sized particles. The physical properties of the synthesized samples were investigated using differential thermal analysis, Fourier-transform infrared spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy, energy-dispersive X-ray analysis, and electrochemical methods. XRD showed that LiMn₂O₄ and LiZn_xHo_yMn_2−x−yO₄ have high degrees of crystallinity and good phase purities. The SEM images of LiMn₂O₄ showed an ice-cube morphology with particles of size 1 μm. Charge–discharge studies showed that undoped LiMn₂O₄ delivered the discharge capacity of 124 mA h/g with coulombic efficiency of 95% during the first cycle, whereas doped spinels delivered discharge capacities of 125, 120, and 127 mA h/g in the first cycle with coulombic efficiencies of 96%, 91%, and 91%, respectively.     

Preparation and gas sensing performances of palladium surface-modified flower-like SnO2 nanopowders

Flower-like SnO2 nanopowders prepared by a hydrothermal method were surface modified with palla- dium via impregnation. The crystal structure, morphology, and surface chemistry states of the samples were characterized by means of X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and X-ray photoelectron spectroscopy （XPS）, respectively. The gas sensing performances were also investigated. For a hydrothermal temperature of 220 ℃, flower-like SnO2 nanoparticles consist of nanorods with diameters of 40 nm and lengths of 100 nm. The XPS and XRD results reveal that palladium exists in the Pd0 chemical state but the crystal is too small to be detected. The 0.3 wt% Pd modified SnO2 sensor shows better sensi- tivity, up to 21, for 70 μL/L ethanol gas at an optimal working temperature of 250 ℃. The quick response time （3 s） and fast recovery time （-20 s） are the main characteristics of this sensor.     

Influence of disodium hydrogen phosphate dodecahydrate on hydrothermal formation of hemihydrate calcium sulfate whiskers

The influence of Na₂HPO₄·12H₂O on the hydrothermal formation of hemihydrate calcium sulfate (CaSO₄·0.5H₂O) whiskers from dihydrate calcium sulfate (CaSO₄·2H₂O) at 135 °C was investigated. Experimental results indicate that the addition of phosphorus accelerates the hydrothermal conversion of CaSO₄·2H₂O to CaSO₄·0.5H₂O via the formation of Ca₃(PO₄)₂ and produces CaSO₄·0.5H₂O whiskers with thinner diameters and shorter lengths. Compared with the blank experiment without Na₂HPO₄·12H₂O, the existence of minor amounts (8.65 × 10⁻⁴–4.36 × 10⁻³ mol/L) of Na₂HPO₄·12H₂O led to a decrease in the diameter of CaSO₄·0.5H₂O whiskers from 1.0–10.0 to 0.5–2.0 μm and lengths from 70–300 to 50–200 μm.     

Fabrication of nano-sized Ca(OH)2 with excellent adsorption ability for N2O4

Uniform nano-sized calcium hydroxide (Ca(OH)₂) monocrystal powder was synthesized from calcium oxide in a surfactant solution via a digestion method by decreasing the surface tension of the reaction system to control the growth of crystalline Ca(OH)₂. The Ca(OH)₂ monocrystal powder samples were characterized by means of scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), and Fourier transform-infrared spectroscopy (FT-IR). The NO_x adsorption ability of the samples was evaluated, and the influence of various types and concentrations of surfactants on powder agglomeration and then the specific surface area in the precipitation process were studied. The specific surface area of the samples was found as high as 58 m²/g and 92 m²/g and the particle size, 300–400 nm and 200–300 nm in the presence of 10 wt% PEG600 and 0.086 mL/L SDS at a reaction time of 5 h, respectively. The product has an exceptionally strong adsorption ability for NO_x, which makes it a highly promising adsorbent for emission control and air purification.     

Controlled synthesis of Ce(OH)CO3 flowers by a hydrothermal method and their thermal conversion to CeO2 flowers

Highly uniform Ce(OH)CO₃ flowers were successfully prepared in large quantities using a facile hydrothermal approach from the reaction of Ce(NH₄)(NO₃)₄ with CO(NH₂)₂ at 160 °C in a water–N₂H₄ complex. The influences of the N₂H₄ content and temperature on flower formation were discussed. CeO₂ flowers were prepared by thermal conversion of Ce(OH)CO₃ flowers at 500 °C in air. Both Ce(OH)CO₃ and CeO₂ flowers were characterized by X-ray powder diffraction (XRD), and scanning electron microscopy (SEM). The UV–vis adsorption spectrum of the CeO₂ flowers showed that the band gap energy (E_g) is 2.66 eV, which is lower than that of bulk ceria.     

Controllable hydrothermal synthesis of star-shaped Sr3Fe2(OH)12 assemblies and their thermal decomposition and magnetic properties

Pure phase star-shaped hydrogarnet Sr₃Fe₂(OH)₁₂ assemblies were synthesized by a mild hydrothermal method (210 °C, 12 h), and the effects of the preparation conditions on the phase composition of the product were investigated. It was found that the impurity phases could be decreased or eliminated by increasing the molar ratio of Sr²⁺ to Fe³⁺, and that high temperatures favored the formation of Sr₃Fe₂(OH)₁₂ and reduced the concentration of CO₃^2–-containing byproducts. The thermal decomposition of the star-shaped Sr₃Fe₂(OH)₁₂ assemblies was examined, and the results showed that the dehydration process at higher temperatures is accompanied by the formation of SrFeO_3–δ. Above 655 °C, a solid state reaction between the SrFeO_3–δ and Sr(OH)₂ or SrCO₃ results in the formation of Sr₄Fe₃O_10–δ.The magnetic properties of the as-synthesized Sr₃Fe₂(OH)₁₂ and of samples calcined at different temperatures were assessed. A sample calcined at 575 °C exhibited greatly enhanced ferromagnetic properties, with a remanent magnetization of 1.28 emu/g and a coercivity of 4522.1 Oe at room temperature.     

Experimental study of lean flammability limits of methane/hydrogen/air mixtures in tubes of different diameters

Lean limit flames in methane/hydrogen/air mixtures propagating in tubes of internal diameters (ID) of 6.0, 8.9, 12.3, 18.4, 25.2, 35.0, and 50.2 mm have been experimentally studied. The flames propagated upward from the open bottom end of the tube to the closed upper end. The content of hydrogen in the fuel gas has been varied in the range 0–40 mol%. Lean flammability limits have been determined; flame shapes recorded and the visible speed of flame propagation measured. Most of the observed limit flames in tubes with diameters in the range of 8.9–18.4 mm had enclosed shape, and could be characterized as distorted or spherical flame balls. The tendency was observed for mixtures with higher hydrogen content to form smaller size, more uniform flame balls in a wider range of tube diameters. At hydrogen content of 20% or more in the fuel gas, limit flames in largest diameters (35.0 mm and 50.2 mm ID) tubes had small, compared to the tube diameter, size and were “lens”-shaped. “Regular” open-front lean limit flames were observed only for the smallest diameters (6.0 mm and 8.9 mm) and largest diameters (35.0 and 50.2 mm ID), and only for methane/air and (90% CH₄ + 10% H₂)/air mixtures, except for 6 mm ID tube in which all limit flames had open front. In all experiments, except for the lean limit flames in methane/air and (90% CH₄ + 10% H₂)/air mixtures in the 8.9 mm ID tube, and all limit flames in 6.0 mm ID tube, visible flame speeds very weakly depended on the hydrogen content in the fuel gas and were close to- or below the theoretical estimate of the speed of a rising hot bubble. This observation suggests that the buoyancy is the major factor which determines the visible flame speed for studied limit flames, except that last mentioned. A decrease of the lean flammability limit value with decreasing the tube diameter was observed for methane/air and (90% CH₄ + 10% H₂)/air mixtures for tubes having internal diameters in the range of 18.4–50.2 mm. This effect has been attributed to the stronger combined effect of the preferential diffusion and flame stretch in narrower tubes for flames which resemble rising bubble.     

Self-assembly of fibrous ZSM-5 zeolites in the presence of sodium alginate

ZSM-5 zeolites with a fibrous morphology were successfully self-assembled in the presence of sodium alginate. The effect of the sodium alginate concentration, Si/Al molar ratio in the synthesis gel, crystallization temperature and time, and the addition order of the sodium alginate on the morphology of the ZSM-5 zeolites was investigated. The possible formation mechanism of fibrous ZSM-5 zeolite crystals was also proposed. The results indicated that the carboxyl and hydroxyl groups of sodium alginate synergistically induced the self-stacking of ZSM-5 nanocrystals and thus the formation of the fibrous ZSM-5 zeolites. The Si/Al molar ratio of the fibrous ZSM-5 zeolites could be adjusted by controlling the amount of the NaAlO₂ additive; however, high Si/Al molar ratios also hindered the self-stacking of ZSM-5 nanocrystals. A high crystallization temperature (180 °C), a moderate sodium alginate concentration (8.33 g/L), and the addition of sodium alginate prior to tetraethoxysilane were necessary for the formation of fibrous ZSM-5 zeolites.     

Microwave-hydrothermal preparation of a graphene/hierarchy structure MnO2 composite for a supercapacitor

Graphene/hierarchy structure manganese dioxide (GN/MnO₂) composites were synthesized using a simple microwave-hydrothermal method. The properties of the prepared composites were analyzed using field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) measurements. The electrochemical performances of the composites were analyzed using cyclic voltammetry, electrochemical impedance spectrometry (EIS), and chronopotentiometry. The results showed that GN/MnO₂ (10 wt% graphene) displayed a specific capacitance of 244 F/g at a current density of 100 mA/g. An excellent cyclic stability was obtained with a capacity retention of approximately 94.3% after 500 cycles in a 1 mol/L Li₂SO₄ solution. The improved electrochemical performance is attributed to the hierarchy structure of the manganese dioxide, which can enlarge the interface between the active materials and the electrolyte. The preparation route provides a new approach for hierarchy structure graphene composites; this work could be readily extended to the preparation of other graphene-based composites with different structures for use in energy storage devices.     

2D reduced graphene oxide–titania nanocomposites synthesized under different hydrothermal conditions for treatment of hazardous organic pollutants

Two-dimensional reduced graphene oxide–titania (RGO–TiO₂) composites were prepared using a single-step hydrothermal method under various hydrothermal reaction conditions. The morphological and surface characteristics of the RGO–TiO₂ composites and reference materials were determined. The RGO–TiO₂ composites showed photocatalytic activity for the decomposition of two target pollutants that was superior to both pure TiO₂ and RGO under fluorescent daylight lamp illumination. The photocatalytic activity of the RGO–TiO₂ composite increased as the hydrothermal treatment time increased from 1 to 24 h, but then it decreased as the time increased to 36 h, which indicated the presence of an optimal treatment time. RGO–TiO₂ composites activated by violet light-emitting diodes (LEDs) displayed lower decomposition efficiency than those activated by a daylight lamp, likely because of the lower light intensity of violet LEDs (0.2 mW/cm²) when compared with that of the daylight lamp (1.4 mW/cm²). However, the photocatalytic decomposition of the target pollutants using the RGO–TiO₂ composite was more energy-efficient using the violet LEDs. The photocatalytic reaction rates increased as the residence time decreased, whereas the reverse was true for the decomposition efficiency.     

Preparation of SiO2/TiO2 Janus particles by electrostatic assembly,hydrolysis and calcination

This paper describes a novel chemical method for preparing SiO₂/TiO₂ Janus particles. First, polystyrene (PSt)/SiO₂ particles with a raspberry-like structure are prepared by electrostatic assembly. The influences of the reaction time of sulfonation and the treatment times of polyelectrolyte solutions (PDADMAC, PSS) on PSt and SiO₂ are investigated with respect to the surface charge density of the particles. SiO₂/TiO₂ Janus particles are then obtained by hydrolysis of butyl titanate on the surface of PSt/SiO₂ particles followed by a calcination process. Particle size analyzer, Zeta potential instrument, FTIR, TEM and SEM are used to characterize the particle size, the amount of charge on the surface of PSt and SiO₂ particles and the compositions and morphologies of PSt/SiO₂, SiO₂/TiO₂ and PSt/SiO₂/TiO₂. The diameters of the PSt, SiO₂, PSt/SiO₂ and SiO₂/TiO₂ particles are 2.0 μm, 303 nm, 2.7 μm and 330 nm, respectively.     

A novel preparation of nanosized hexagonal Mg(OH)2 as a flame retardant

Nanosized dispersive hexagonal magnesium hydroxide (Mg(OH)₂) has been prepared using an ammonia-hydrothermal method. Citric acid and monoethanolamine (MEA) were added to the reaction system during the ammonia precipitation and hydrothermal processes, respectively, to improve the crystallinity and dispersion of the (Mg(OH)₂) particles. The resulting Mg(OH)₂ samples obtained under the optimum preparation conditions were characterized by scanning electron microscopy, X-ray diffraction and thermal gravity analysis, which showed that this newly developed procedure afforded well-dispersed hexagonal nanoplates of Mg(OH)₂ with a mean diameter of 246 nm.     

Magnetic and electrochemical behavior of rhombohedral α-Fe2O3 nanoparticles with (1 0 4) dominant facets

Uniform rhombohedral α-Fe₂O₃ nanoparticles, ～60 nm in size, were synthesized via a triphenylphosphine-assisted hydrothermal method. Scanning electron micrograph (SEM) and transmission electron micrograph (TEM) analyses showed that the as-synthesized rhombohedral nanoparticles were enclosed by six (1 0 4) planes. The concentration of triphenylphosphine played an important role in morphological evolution of the α-Fe₂O₃ nanoparticles. The as-prepared rhombohedral nanoparticles possessed remanent magnetization M_r of 2.6 × 10^?3 emu/g and coercivity H_C of 2.05 Oe, both lower than those of other α-Fe₂O₃ particles with similar size, indicating their potential applications as superparamagnetic precursor materials. Furthermore, these rhombohedral α-Fe₂O₃ nanoparticles exhibited good sensor capability toward H₂O₂ with a linear response in the concentration range of 2–20 mM.