Determination of arsenic by inductively-coupled plasma atomic emission spectrometry enhanced by hydride generation from organized media

A method is described for the determination of arsenic, which combines a continuous flow hydride generation technique with an inductively coupled plasma atomic emission detection system. Some atomic absorption preliminary studies are described as well. Arsine is generated with NaBH(4) from a didodecyldimethylammonium bromide (DDBA) vesicular medium. The analytical performance of this vesicles-enhanced method is superior to the generation of the hydride from aqueous media: the detection limit (0.6 ppb) is improved by a factor of 2 and greater tolerance to interferences is observed for arsine generation from DDBA vesicles. Precision of As determinations is also improved. The proposed method has been validated for low As levels determinations in two Certified Reference Materials (CRM) sediments with satisfactory results. The potential of organized media to improve hydride generation is addressed.     

碱性体系在线氢化物发生—原子荧光光谱法测定痕量铋

提出了一种碱性体系在线氢化物发生－原子荧光光谱法测定痕量铋的分析方法。设计了在线氢化物发生系统流路及操作程序，研究了碱性体系氢化物发生的各项最佳条件。方法操作简便快速，能有效地消除过渡元素的严重化学干扰。应用于黄铜标样中痕量铋的直接测定，获得满意结果。     

Electrochemical hydride generation of thallium

An electrochemical hydride generation (ECHG) technique was developed to improve the determination of thallium by atomic spectrometry. The technique is based on the catholyte variation system for production of thallium hydride. Using Pb-Sn alloy as cathode, a transient peak shaped signal was achieved and its height, the maximum absorbance value, was taken as an analytical parameter. Parameters that might affect the hydride generation efficiency were investigated and the analytical performance of the method under the optimized experimental conditions was assessed. The linear range was 1-250 ng mL⁻¹ for thallium and the relative standard deviation of the method was 4.2% (RSD, n = 7). The LOD for thallium was found to be 0.8 ng mL⁻¹, showing a significant improvement relative to conventional chemical hydride generation techniques. The proposed method was applied to the determination of thallium in unalloyed zinc standard reference material. This method offers high sensitivity, simplicity, rapidness, freeness from reagent and low acid consumption.     

Development of an automated technique for the speciation of arsenic using flow injection hydride generation atomic absorption spectrometry (FI-HG-AAS)

An automated method for the determination of arsenic acid (AsV), arsenous acid (AsIII), monomethylarsonic acid (MMAA) and dimethylarsinic acid (DMAA) was developed using a commercial available flow injection hydride generation system. By carrying out the hydride generation in selected acid media the determination of As(III) alone, of MMAA and DMAA by sum and by different sensitivities, and of all four species is possible.     

开叉毛细管HG-FAAS测定地质样品中的锑、铋

氢化物发生原子吸收法(HG-FAAS)广泛应用于冶金、地质、环境、医药和食品分析等领域中。研究表明,氢化物发生法的检出限、测定精度以及干扰等情况与原子化器和氢化物发生器的结构以及传输过程有关[1]。郭小伟等[2-4]研制了用于火焰原子吸收光谱分析的双毛细管喷雾器,并利用其测     

Determination of lead in wines by hydride generation atomic absorption spectrometry.

The optimization of lead hydride generation in aqueous ethanolic media and the influence on its generation of the wine components, both white and red, have been studied. These interferences were overcome by careful control of the parameters affecting hydride generation and the procedure was applied to the determination of Pb in wines. The method is fast, accurate and sensitive and can be used to quantify 24 ppb of Pb in wines.     

Electrothermal atomic absorption spectrometric determination of ultra-trace amounts of tin by in situ preconcentration in a graphite tube using flow injection hydride generation with on-line ion-exchange separation

A method was developed for the ultra-trace determination of tin by in situ preconcentration in a graphite tube using a flow injection hydride generation technique with on-line ion-exchange separation. The sample was prepared in 2M hydrochloric acid before being passed through an incorporated micro-column packed with a strongly basic anion-exchanger D-201. The tin was retained as its chlorostannate complex and subsequently eluted by de-ionized water into the hydride generation system. The hydride and hydrogen gases evolved were separated from the liquid phase in a gas-liquid separator and transferred into a palladium-coated graphite tube pre-heated to 300 degrees C to collect the analyte, which was later atomized at 2300 degrees C. With the reported system, tin was determined at a sampling frequency of 30/hr with a detection limit (3sigma) of 0.01 mug/l. using 10.7 ml sample. The precision was 1.5% RSD at the 0.5 mug/l. level. The proposed method was applied to the determination of tin in tap water, hair, serum samples and geological reference samples.     

Determination of zinc in foods by fluorescence spectroscopy in micellar media

The effect of cationic [cetyltrimethylammonium bromide (CTAB), Zephiramine], non-ionic (Triton X-100, Brij-35) and anionic (sodium lauryl sulphate) surfactant micelles on the fluorescence intensity of the zinc 5,7-dichloro-2-methylquinolin-8-ol chelate is described. In Brij-35 or CTAB micellar media, the fluorescence is about 25 times greater than that obtained in ethanol-water. The relationship between fluorescence intensity and experimental variables was studied in order to develop a procedure for the fluorimetric determination of zinc. Linear calibration graphs were obtained in the ranges 3–100 and 50–400 ng Zn ml^?1. The detection limit is 3 ng ml^?1. The method was successfully applied to the determination of zinc in food samples and drinking waters.     

Co-Hydride Enhancement Effects in Cadmium,Zinc and Thallium Hydride Generation Measurements

Until recently hydride generation (HG) technique had been applied to only a limited number of elements. In attempts to extend the technique to cadmium, Guo and Guo found that the presence of thiourea together with cobalt enhanced the signal intensity of the Cd volatile species. This finding was repeated and confirmed by many authors. Moreover, Ga and Si, Fe and Ni were used to improve the sensitivity for Cd determination. Recently, the vapour generation of Zn species was performed using an intermittent flow reactor by Guo and Guo,it was found that Ni and Co ions greatly enhanced the signal intensity of zinc. Early in 1984,Yan and co-works reported that the addition of hydride-forming elements, especially tellurium, "accelerated" the formation of thallium hydride rapidly, and suggested a complex hydride was formed. According to these reports, it seems that the addition of certain foreign ions has a positive effect to such elements as Cd, Zn, and Tl, which form unstable hydrides. But the mechanism of the effect of these foreign ions remains unexplained.     

Determination of Inorganic Sb(V) and Methylantimony Species by HPLC with Hydride Generation-Atomic Fluorescence Spectrometric Detection

 An on-line method for the separation and analysis of Sb(V) and Me₃Sb in the presence of Sb(III) in liquid samples is described. Inorganic and organic antimony species were separated using anion-exchange high-performance liquid chromatography (HPLC) coupled with hydride generation-atomic fluorescence detection (HG-AFS). Optimum conditions for the separation of antimony species by HPLC and the hydride generation conditions for the determination by HG-AFS were established. Matrix interference of the chromatographic determination was studied in relation to MgSO₄ and NaCl. The method developed was applied to the separation and determination of antimony species in spiked and natural water samples. The suitability of the method for analysis in microbial growth media and physiological studies involving methylantimony species is discussed. Received December 11, 2000. Revision April 26, 2001.     

Comparison of four microwave digestion methods for the determination of selenium in fish tissue by using hydride generation atomic absorption spectrometry

Four microwave digestion methods of fish tissue for selenium determination by hydride generation atomic absorption spectrometry were compared, in which potassium hexacyanoferrate(III) was chosen as a masking agent for eliminating matrix interferences. The results showed that the methods employing HNO(3)/H(2)O(2), HNO(3)/K(2)S(2)O(8)/H(2)O(2) and HNO(3)/H(3)PO(4)/H(2)O(2) digestion media were unreliable. However, the decomposition using the digestion media of HNO(3)/H(2)SO(4)/H(2)O(2) enabled adequate digestion of fish tissue and retention of selenium in a state amenable for determination. Therefore, the digestion procedures with HNO(3)/H(2)SO(4)/H(2)O(2) media are proposed for the determination of selenium in fish tissue by hydride generation atomic absorption spectrometry. The recoveries of the spiked samples investigated ranged from 90 to 102%. The result obtained from analyzing the NIES CRM No. 6 mussel was in good agreement with the reference value (reference value: 1.5 mug/g; found: 1.45 +/- 0.05 mug/g). The limit of detection for selenium was 0.03 mug/g dry mass for a 100 mg sample. The contents of selenium in local fish species investigated ranged from 0.49 to 2.90 mug/g, and the relative standard deviation for the determination of selenium was less than 8%.     

Microwave-assisted synthesis of ZnO and its photocatalytic activity in degradation of CTAB

Nanosized zinc oxide (nano-ZnO) was prepared by a microwave irradiation method using zinc nitrate and triethanolamine as starting materials and distilled water as a solvent. The as-prepared powder was characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The photocatalytic degradation of cetyltrimethylammonium bromide (CTAB) using the prepared material under UV irradiation was studied.The effects of ZnO dosage and initial pH on the photodegradation of CTAB were investigated. As the ZnO load increased, the CTAB degradation first increased and then decreased. The optimum ZnO dosage was 3 g L^–1. Photodegradation of CTAB is more efficient in slightly alkaline media (pH 9).     

萃取-非水介质氢化物发生-ICP-AES中的干扰及Ni-Fe基合金的分析

本文结合溶剂萃取研究了非水介质中氢化物发生-ICP-AES的分析条件、干扰等因素的影响。利用KI~+H_2SO_4/MIBK萃取体系将As,Sb,Bi萃取到MIBK中而与基体元素分离,然后将该有机相与甲酸按等体积混合后,即可直接进行氢化物发生-ICP-AES分析。还对影响萃取和氢化物发生的一些因素及共存元素的干扰进行了讨论。该方法应用于Ni-Fe基合金中As和Sb的分析,取得了较满意的结果。     

Evaluation of oxidant media for the determination of lead in food slurries by hydride generation atomic absorption spectrometry

Several oxidant media were evaluated for the generation of lead hydride from slurry samples and their application to the determination of lead in vegetables and fish by hydride generation atomic absorption spectrometry. Three oxidant - acid media were compared: hydrogen peroxide - nitric acid, ammonium persulphate - nitric acid and potassium dichromate - lactic acid. The powdered samples were suspended in Triton X-100 and shaken with 10.0 g of blown zirconia spheres until a slurry was formed. The potassium dichromate - lactic acid medium was the most satisfactory for the determination of lead in fish and vegetables, providing the lowest detection limits as a result of its high sensitivity and low blank values. The ammonium persulphate - nitric acid medium gave good accuracy, precision and selectivity for vegetables (1-2 p.p.m. of lead); however, with fish (0.1-1 p.p.m. of lead) it was only a semi-quantitative medium for the determination of lead owing to its lack of sensitivity and selectivity. The hydrogen peroxide - nitric acid medium was unsatisfactory for the generation of lead hydride from slurry samples because of decomposition of hydrogen peroxide by the organic matter in the sample.     

Evaluation of electrochemical hydride generation for spectrophotometric determination of As(III) by silver diethyldithiocarbamate

A batch electrochemical hydride generation system was developed for the spectrophotometric determination of inorganic As(III) by silver diethyldithiocarbamate. This method is based on electrochemical reduction of As to Arsine (AsH₃) in acidic media and on the subsequent reaction of AsH₃ with silver diethyldithiocarbamate to give an absorbing complex at 525 nm. The electrochemical generator consisted of a cathode cell separated from the anode cell by a porous glass frit and was operated with a constant direct current. A pre-activated graphite rod was used as cathode material for the production of AsH₃. The parameters related to the electrochemical hydride generation were investigated. Under optimized conditions, only As(III) can be converted to AsH₃ and a pre-reducing stage is required for total inorganic As analysis. The characteristic data of the electrochemical hydride generation and common hydride generation by NaBH₄ were compared. Also, the effects of interferences and their elimination were investigated. An absolute detection limit of 0.5 μg (3s_b) and a concentration detection limit of 0.05 μg/ml were obtained using a 10 ml sample volume. The relative standard deviation for five replicate analysis of 30 μg As(III) was 1.2%. The accuracy and recovery of the method were demonstrated by analysing spiked artificial sea water and tap water.     

原子荧光光谱法测定镉锭中锡的含量

采用氢化物发生-原子荧光光谱法测定镉锭中锡含量,研究了基体镉对锡的干扰及消除方法,优化了氢化物的发生条件,建立了镉锭中锡含量的快速分析方法。实验证明,原子荧光光谱法对锡的检出限为0.08mg/kg,回收率为99.0%～104.0%,方法准确、可靠,用于日常样品分析,取得了很好的效果。     

Determination of aluminium(III) in water samples in a microemulsion system by spectrofluorimetry

The sensitizing effect of cetyltrimetrylammonium bromide (CTAB) microemulsion media on the determination of aluminium(III) by spectrofluorimetry was developed. The main factors affecting the determination were investigated in detail. The results showed that 8-hydroxyquinoline (HQ) react with aluminium(III) forming a complex with fluorescence in the system of potassium acid phthalate-NaOH buffer solution at pH 6.0, the maximum excitation and emission wavelengths are at 380.0 and 502.6 nm, the sensitizing effect of CTAB microemulsion is higher than that of CTAB micelle. The proposed method has been applied to the determination of aluminium(III) in tap water and lake water samples with satisfactory results.     

Investigations for the determination of lead by in situ hydride trapping within a graphite electrothermal atomizer for routine analysis

A new commercial system consisting of a flow injection analysis system for hydride generation coupled with a transversely heated graphite atomizer-atomic absorption spectrometer for the determination of lead is investigated in detail. The hydride generation is optimized by using an ammonium peroxodisulphate-hydrochloric acid system as oxidant and sodium borohydride as reducing reagent. The addition of sodium cumol sulphonate as surface active substance shows advantages considering efficient plumbane production. The hydride trapping and atomization in a graphite electrothermal atomizer is also optimized. The characteristic concentration was 0.74 mug/l, the detection limit was 0.70 mug/l for 500 mul sample volumes. The relative operation standard deviation of this method was smaller than 2%. Further examinations demonstrate the influence of several heavy metals on the determination of lead. Finally, the measurement of standard reference materials shows the efficiency of the method in combination with decomposition with aqua regia solutions.     

共价氢化物与汞离子反应的研究 Ⅰ 痕量锑高灵敏度的分析新方法

本文提出了一个氢化物发生一冷原子荧光法间接测定痕量锑的新方法。考察了各种实验条件,并将此法用于水及沉积物标样分析,结果令人满意,对水中锑检出限为0.1μg/L,回收率96％～102％。     

Simultaneous determination of arsenic and antimony by hydride generation atomic fluorescence spectrometry with dielectric barrier discharge atomizer

Simultaneous determination of As and Sb by hydride generation atomic fluorescence spectrometry was developed with the dielectric barrier discharge plasma as the hydride atomizer. The low-temperature and atmospheric-pressure micro-plasma was generated in a quartz cylindrical configuration device, which was constructed by an axial internal electrode and an outer electrode surrounding outside of the tube. The optimization of the atomizer construction and parameters for hydride generation and fluorescence detection systems were carried out. Under the optimized conditions, the detection limits for As and Sb were 0.04 and 0.05 μg L⁻¹, respectively. In addition, the applicability of the present method was confirmed by the detection of As and Sb in reference materials of quartz sandstone (GBW07106) and argillaceous limestone (GBW07108). The present work provided a new approach to exploit the miniaturized hydride generation dielectric barrier discharge atomic fluorescence spectrometry system for simultaneous multi-element determination.