An optimal method for the design of a robotic tracked vehicle to operate over fresh concrete under steering motion

The objective of this paper is to find an optimal method for the design of tracked base travel systems for special purpose vehicles and robotic machines that may be required to steer over a light bonded terrain composed of fresh concrete. For the case of a vehicle traveling on a weak fresh concrete during construction, the paper presents detailed comparative studies of the steering performances of a small model tracked test vehicle with alternative amount of steering ratio for various concrete slump values. For these studies a detailed simulation analytical method has been developed. From this work it is proven, in comparison to experiment, that the simulation analytical method is useful for predicting various steering performances of a test tracked vehicle running upon soft fresh concrete of various consistencies.     

Development of a tracked vehicle to study the influence of vehicle parameters on tractive performance in soft terrain

This paper describes a new special tracked vehicle for use in studying the influence of different vehicle parameters on mobility in soft terrain; particularly muskegg and deep snow. A field test in deep snow was carried out to investigate the influence of nominal ground pressure on tractive performance of the vehicle. The vehicle proved useful for studying vehicle parameters influencing the tractive performance of tracked vehicles. The tests show that the nominal ground pressure has a significant effect on the tractive performance of tracked vehicles in deep snow. The decrease in drawbar pull coefficient when the nominal ground pressure is increased and originates at about the same amount from a decrease of the vehicle thrust coefficient, an increase of the belly drag coefficient and an increase of the track motion resistance coefficient.     

How to calculate the effect of soil conditions on tractive performance

The paper presents an analysis and quantitative evaluation of the effect of soil conditions on tractive performance of off-road wheeled and tracked vehicles. The results of this study indicated that to accurately calculate the tractive performance of a vehicle in a given soil condition, soil properties and parameters and their changes as functions of soil moisture content and density should be taken into account. An effective Tractive Performance Analytical (TPA) model which takes into consideration the effect of soil conditions on tractive performance of the vehicles is developed. The TPA model uses invariant soil parameters that can be given or measured before the calculations by routine methods of classical soil mechanics. Soil parameters can also be obtained by recommended empirical equations using four physical soil parameters measured in the field with hand held instruments without time consuming and costly plate or vehicle tests. The model was validated in different soil conditions and compared with other models used in terramechanics for tractive performance predictions. The paper includes also an analysis of capabilities and limitations of the observed models.     

Predicting mobility performance of a small,lightweight track system using the computer-aided method NTVPM

This paper describes the results of a study of applying the physics-based, computer-aided method – the Nepean Tracked Vehicle Performance Model (NTVPM), originally developed for evaluating the mobility of large, heavy tracked vehicles, to predicting the performance of a small, lightweight track system on sandy soil. The objective is to examine the applicability of NTVPM to predicting the cross-country performance of small, lightweight tracked vehicles on deformable terrain. The performance of the track system predicted by NTVPM is compared with experimental data obtained in a laboratory soil bin by the Robotic Mobility Group, Massachusetts Institute of Technology. It is shown that the correlation between the tractive performance predicted by NTVPM and that measured is reasonably close, as indicated by the values of the coefficient of correlation, coefficient of determination, root mean squared deviation, and coefficient of variation. The results of this study provide evidence for supporting the view that physics-based methods, such as NTVPM, that are developed on the understanding of the physical nature and detailed analysis of vehicle–terrain interaction, are applicable to large, heavy, as well as small, lightweight vehicles, provided that appropriate terrain data are used as input.     

“Wheels vs. tracks” – A fundamental evaluation from the traction perspective

The issue of wheeled vehicles vs. tracked vehicles for off-road operations has been a subject of debate for a long period of time. Recent interest in the development of vehicles for the rapid deployment of armed forces has given a new impetus to this debate. While a number of experimental studies in comparing the performances of specific wheeled vehicles with those of tracked vehicles under selected operating environments have been performed, it appears that relatively little fundamental analysis on this subject has been published in the open literature, including the Journal of Terramechanics. This paper is aimed at evaluating the tractive performance of wheeled and tracked vehicles from the standpoint of the mechanics of vehicle–terrain interaction. The differences between a tire and a track in generating thrust are elucidated. The basic factors that affect the gross traction of wheeled and tracked vehicles are identified. A general comparison of the thrust developed by a multi-axle wheeled vehicle with that of a tracked vehicle is made, based on certain simplifying assumptions. As the interaction between an off-road vehicle and unprepared terrain is very complex, to compare the performance of a wheeled vehicle with that of a tracked vehicle realistically, comprehensive computer simulation models are required. Two computer simulation models, one for wheeled vehicles, known as NWVPM, and the other for tracked vehicles, known as NTVPM, are described. As an example of the applications of these two computer simulation models, the mobility of an 8 × 8 wheeled vehicle, similar to a light armoured vehicle (LAV), is compared with that of a tracked vehicle, similar to an armoured personnel carrier (APC). It is hoped that this study will illustrate the fundamental factors that limit the traction of wheeled vehicles in comparison with that of tracked vehicles, hence contributing to a better understanding of the issue of wheels vs. tracks.     

Traffic performance of a rubber-tracked vehicle travelling up and down a sloped pavement

The tractive and braking performances of a 40 kN rubber-tracked vehicle travelling up and down a sloped pavement depend on the grouser shape. The purpose of this paper is to find the most suitable grouser shape to obtain the maximum optimum effective tractive effort and the maximum optimum effective braking force and to clarify the several traffic performances of the vehicle travelling up and down sloped concrete and asphalt paved roads. As results, it is verified that the most suitable shape of rubber grouser is an equilateral trapezoid type of contact length 3 cm for concrete pavement and another of contact length 5 cm for asphalt pavement, respectively, and that the effective tractive effort and the effective braking force decrease with the increment of slope angle.     

A new contact & slip model for tracked vehicle transient dynamics on hard ground

This study presents a new general transient contact and slip model for tracked vehicles on hard ground which is simple, accurate, and in agreement with the test results to a satisfactory level. Simulating zero track speed instances become possible with the new contact/shear model which is the major proposed improvement in addition to more accurate results for transient steering and tractive inputs. The model represents a general tracked vehicle having rear or front sprockets, with parameters for center of gravity, wheel positions, number of wheels, and track-pretention. To calculate longitudinal and lateral forces, a transient shear model is used. Shear stress under each track pad is assumed to be a function of shear displacement. The contact time formulation used in shear displacement calculation is improved to gain accuracy for transient and zero track speed conditions.The model is implemented on the Matlab/Simulink platform and verified with a comprehensive program of road tests composed of transient steering and tractive/braking scenarios. The results of the simulations and the road tests are satisfactorily similar for both constant and transient input maneuvers. Moreover, sensitivity simulations for vehicle parameters are conducted to show that the model responses are inline with the expected vehicle dynamics behaviours.     

Slip sinkage effect in soil-vehicle mechanics

The paper presents an analysis and quantitative evaluation of the slip sinkage and its effect on the tractive performance of wheeled and tracked vehicles in different soils. The results of this study indicated that to accurately predict the sinkage and motion resistance of a vehicle in a given soil and operating conditions, the slip sinkage effect should be taken into account. An effective analytical formula that takes into consideration the slip sinkage effect on sinkage of plates and vehicles is developed. The formula was validated in different soil conditions and compared with other formulae used in terramechanics for slip sinkage effect predictions.     

Evaluation of drawbar performance of winter tyres for special purpose vehicles

Driving on ice is still a risky activity. Research has investigated the factors contributing to the friction mechanism and has reported experimental studies of pneumatic tyres on ice in order to develop models that predict tractive and braking performance on ice/snow. Therefore, developing testing methods to obtain relevant experimental data for the validation of models is equally important.There are agricultural and industrial vehicles which are also designed for pulling but there are no specific studies reporting experimental tests on traction force of such machines in snowy conditions. However, this issue is very topical, as demonstrated by the appearance on the market of winter tyres for such vehicles.This study presents a method for testing winter tyres in outdoor test facilities with a focus on traction performance. The conclusions will serve in future investigations as a concise knowledge source to develop improved testing facilities and tyre–ice interaction models, aiding the development of better tyre designs and improved vehicle safety systems.The functional tests hereafter described have been carried out with the aim of evaluating the possibility of measuring the influences of different technique solutions on the performance of certain 17.5 R25 sized industrial tyres.     

Prediction of the tractive performance of a flexible tracked vehicle

In this study, we describe a mathematical model designed to allow for the determination of the mechanical relationship existing between soil characteristics and the primary design factors of a tracked vehicle, and to predict the tractive performance of this tracked vehicle on soft terrain. On the basis of the mathematical model, a computer simulation program (Tractive Performance Prediction Model for Tracked Vehicles; TPPMTV) was developed in this study. This model took into account the characteristics of the terrain, including the pressure-sinkage, the shearing characteristics, and the response to the repetitive loading, as well as the primary design parameters of the tracked vehicle. The efficacy of the developed model was then confirmed via comparison of the drawbar pulls of tracked vehicles predicted using the simulation program TPPMTV, with those determined as the result of traction tests. The results indicated that the predicted drawbar pulls, with the change in slip, were quite consistent with the ones measured in the traction test, for the changes in the weight of the vehicle, the initial track tension, and the number of roadwheels within the entire slip range. Thus, we concluded that the simulation program developed in this study, named TPPMTV, proved useful in the prediction of the tractive performance of a tracked vehicle, and that this system might be applicable to the design of a vehicle, possibly enabling a significant improvement in its functions.     

Development of high-mobility tracked vehicles for over snow operations

This paper describes a detailed investigation into the effects of some of the major design features on the mobility of tracked vehicles over snow. The investigation was carried out using the latest version of an advanced computer simulation model, known as NTVPM, developed under the auspices of Vehicle Systems Development Corporation (VSDC), Ottawa, Ontario, Canada. Results show that the road wheel system configuration, initial track tension (i.e., the tension in the track system when the vehicle is stationary on a level, hard ground) and track width have significant effects on vehicle mobility over snow. On deep snow where the vehicle belly (hull) contacts the snow surface, the location of the centre of gravity (C.G.) of the sprung weight in the longitudinal direction has a noticeable effect on vehicle mobility, as it affects the attitude of the belly and the belly–snow interaction. Based on the investigation, a conceptual high-mobility tracked vehicle for over snow operations is discussed. Results of this study will provide the vehicle designer with guiding principles for the development of high-mobility tracked vehicles. It also demonstrates that NTVPM is a useful and effective tool for design and performance evaluation of tracked vehicles from a traction perspective.     

Tractive and braking performance of a flexible tracked tractor moving up and down weak sloped terrain

The objective of this study is to analyse the tractive and braking performance of a tractor travelling up and down a weak silty loam sloped terrain. The effects of track belt size on terrain-track system parameters were investigated experimentally, and the force and energy balances were clarified for the actual flexible tracked vehicle. The flexibility of the track belt has been precisely analysed as a function of track tension, loading and reloading properties of terrain, and contact pressure distributions. The results show that the optimum effective driving (or braking) force decreases with the increase of slope angle due to the decreasing vehicle weight component, while the thrust (or drag) decreases and the compaction resistance increases. The contact pressure distribution under the flexible track belt shows a triangular wavy pattern having peak values under each track roller. The shear resistance distribution has positive and negative peak values for the driving and braking states, respectively.     

Automatic control system of a rear-wheel drive vehicle moving on a sloped weak sandy terrain

The general mechanism of tractive performance of a four-wheel vehicle with rear-wheel drive moving up and down a sloped sandy soil has been considered theoretically. For the given vehicle dimensions and terrain-wheel system constants, the relationships among the effective tractive or braking effort of the vehicle, the amount of sinkage of the front and rear wheels, and the slip ratio were analysed by simulation. The optimum eccentricity of the vehicle’s center of gravity and the optimum application height of the drawbar-pull for obtaining the largest value of maximum effective tractive or braking effort could be calculated by means of the analytical simulation program. For a 5.88 kN weight vehicle, it was found that the optimum eccentricity of the center of gravity e_opt was 1/6 for the range of slope angle—0βπ/24 rad during driving action of the rear wheel and e_opt was also 1/6 for the range of slope angle—π/24β0 rad during braking action of the rear wheel. The optimum application height H_opt was found to be 35 cm for the range of slope angle 0βπ/24 rad during driving action of the rear wheel and H_opt was 0 cm for the range of slope angle—π/24β0 rad during braking action of the rear wheel.     

Numerical simulation and testing verification of the interaction between track and sandy ground based on discrete element method

Tractive effort of tracked vehicles plays an important role in military and agricultural fields. In order to solve the problem of low precision in numerical simulation of the interaction between track and sandy ground, a systematic and accurate discrete element modeling method for sandy road was proposed. The sandy ground was modeled according to the mechanical parameters measured by soil mechanics tests. The interaction coefficients of sandy soil were measured by the repose angle test and triaxial compression test combined with the corresponding simulation. On this basis, a discrete element interaction model of track-sandy ground was established, which can be used to test the tractive effort of track. Numerical simulation calculation of track model at different speeds was carried out, and the simulation results were compared with the results of indoor soil bin test for verification. The verification results show that the interaction between track and sandy ground based on DEM simulation is consistent with the actual soil bin test. The discrete element modeling method in this paper can be used to model the track and sandy ground accurately, and the simulation model can be used to test the tractive effort of tracked vehicle.     

Application of the computer simulation model NTVPM-86 to the development of a new version of the infantry fighting vehicle ASCOD

In the past, the task of evaluating soft-ground mobility of off-road vehicles has been carried out primarily using empirical methods (or models), such as the NATO Reference Mobility Model (NRMM) or the Rowland method based on the mean maximum pressure (MMP). The databases for these empirical methods were mostly established decades ago. Consequently, in many cases, they cannot be used in evaluating new generations of vehicles with new design features, as the mobility of these vehicles simply cannot be described within the limits of these empirical databases.Since the 1980s, a series of comprehensive and realistic simulation models for design and performance evaluation of off-road vehicles has emerged. They are based on the detailed studies of the physical nature of vehicle-terrain interaction, taking into account all major vehicle design features and pertinent terrain characteristics. This paper describes the application of one of these models, known as NTVPM-86, developed by Vehicle Systems Development Corporation, Canada, to the design and development of a new version of the ASCOD infantry fighting vehicle, produced by a joint venture formed by Empresa Nacional Santa Barbara of Spain and Steyr-Daimler-Puch of Austria. The results of field tests performed by the Military Technology Agency, Ministry of Defence, Vienna, Austria and released recently confirm that, as predicted by the NTVPM-86 model, the new version of the ASCOD has much improved performance than the original over soft terrain, including soft clay and snow-covered terrain. This is another example of the successful application of the NTVPM-86 model to the design and development of a new generation of high-speed tracked vehicles.     

A methodology for quantitatively assessing vehicular rutting on terrains

This paper presents a quantitative method for assessing the environmental impact of terrain/vehicle interactions during tactical missions. Area wide mobility analyses were conducted using three standard US military tracked and wheeled vehicles over terrain regions representing both fine-grained and course-grained soils. The NATO reference mobility model, Version 2, was used to perform the on- and off-road mobility analysis. Vehicle and terrain characterizations along with different climate scenarios were used as input parameters to predict vehicle rut depth performance for the different vehicles and terrain conditions. The vehicles’ performance was statistically mapped over these terrain regions for percent area traveled and the resulting rut depth created by each vehicle. A selection of tactical scenarios for each vehicle was used to determine rut depth for a range of vehicle missions. A vehicle mission severity rating method, developed at the US Army Engineer Research and Development Center, was used to rate the selected missions and resulting rut depths.     

The optimum height of application of force and eccentricity of a wheeled vehicle running on a loose sandy soil

In earthmoving sites, multi-wheeled vehicles are used to excavate a sandy soil or to pull other construction machinery. In this paper, the mechanism of a 5.88 kN weight, two-axle, four-wheel vehicle running on a loose sandy soil is theoretically analysed. For given terrain-wheel system constants, the combination of the effective braking force of the front wheel during pure rolling state and the effective driving force of the rear wheel during driving action will clarify the relation between effective effort of the vehicle and slip ratio and the relation between amounts of sinkage the front and rear wheels and slip ratio, etc. The maximum effective tractive effort of the vehicle varies with the height of application force and the position of the center of gravity of the vehicle. The optimum height of application of force and the eccentricity of the center of gravity to obtain the largest value of the maximum effective tractive effort can be explained with an analytical simulation program. Results of this study showed that the optimum height of application force should be 30 cm and the optimum eccentricity of the center of gravity is 0.05 for a vehicle considered for this study.     

THREE DIMENSIONAL MODELING AND DYNAMIC ANALYSIS OF FOUR—WHEEL—STEERING VEHICLES

The paper presents a nonlinear dynamic model of 9 degrees of freedom for four-wheel-steering vehicles. Compared with those in previous studies, this model includes the pitch and roll of the vehicle body, the motion of 4 wheels in the accelerating or braking process, the nonlinear coupling of vehicle body and unsprung part, as well as the air drag and wind effect. As a result, the model can be used for the analysis of various maneuvers of the four-wheel-steering vehicles. In addition, the previous models can be considered as a special case of this model. The paper gives some case studies for the dynamic performance of a four-wheel-steering vehicle under step input and saw-tooth input of steering angle applied on the front wheels, respectively. The project supported by the National Natural Science Foundation of China (59625511)     

Tractive performance and compaction effect of a road roller running on a weak sandy soil

This study aims to investigate the tractive performance of a two-axle, two-wheel vehicle with rear-wheel drive or brake and the compaction of a decomposed granite soil. The effects of traction or braking, the change of sinkage, the slip ratio of the front and rear roller, and the number of passes of the road roller were studied. A number of tests were conducted and the experimental data were compared with the theoretical analysis results. It was observed that the amount of sinkage on the front and rear roller took the minimum value when the front roller was in the unpowered rolling state and the slip ratio of the rear roller was almost zero. When the absolute value of the slip ratio of rear roller increased, the amount of sinkage on the front and rear rollers, the absolute value of the driven or braking force of the rear roller and the absolute value of effective tractive or braking effort of the road roller increased. When the front roller was in the unpowered rolling state and the rear roller was in the braking state at −5% skid, the compaction density of the soil was at a maximum.     

Etude de la direction des véhicules articulés à chenille (l analyse théorique et expérimentale)

This paper presents theoretical and experimental analysis of steering performance of articulated tracked vehicles on level ground. A mathematical model for predicting the steerability of articulated units has been developed and computerized for numerical application. The accuracy of the analog has been verified by scale model tests.From the results of the simulation and scale model tests it was found that steerability was significantly improved and required sprocket torques for steering and track slippage were considerably decreased in articulated tracked vehicles when compared with a single and coupled tracked vehicles.